Configuration of VLAN Switch Distributed

Similar Questions

• Ill at 5.5 VLAN switch distributed

  Begging for a little help. It's my first knife to set up a VLAN on an ESXi 5.5 Distributed Switch. I'm used to the physical switches... Dell & Cisco...

  Installation program:

  Firewall

  > > WAN1 [5 x static IP] > > WAN to the firewall

  > > WAN2 [1 x, DHCP] > > WAN to the firewall

  > > LAN1 "VMnet" 10.x.1.x/24 > > Firewall > Port1 on Dell PowerConnect 2748 (switch is not compatible trunking)

  > > LAN2 "WiFi" 10.x.2.x/24 [adapter Wireless Firewall]

  > > VLAN1 Switch1 Port1 'tag 'ESXiNet' [VMkernel + vMotion] 10.x.3.x/24' > > Switch1, Port 14 "Untagged."

  > > Port 14 on Switch1 attends Port2 on Switch3 [Dell PowerConnect 2716]

  > > Port 2 on Switch3 is 'tag', 3-16 Ports are not all "marked" and all go direct to VMkernel NIC card pairs for redundancy.

  > > VLAN2 "OfficeNET' 10.x.4.x/24 Switch1 Port1 to Switch1 LAG1 [Ports Switch1 15 & 16] > > Switch2 Ports 1 and 2 as"Gal1"[Dell PowerConnect 2724]

  > > VLAN3 'AdminNet' 10.x.5.x/24 Switch1 Port1 to Switch1 Ports 40-48

  Problem is that I have a VLAN that comes out of my Dell PowerConnect 2748 switch and enter an ESXi host. VLAN is #99. If I connect a laptop directly into the switch I get an IP DHCP correctly of the switch address on this VLAN. If I plug this LAG (or individual port if I break upwards the LAG) in my ESXi hosts can't pass the VIRTUAL local area network via the distributed switch.

  You are looking for assistance. Hope that the above explanation makes sense. Just trying to get one VLAN through a switch distributed to a virtual machine.

  Sorry for the bug to the community with this configuration. It seems that it was my fault... or my mistake. I got it setup properly from the start... For all those who in the future that concludes this thread...

  Firewall VLAN # 100 > Switch Port 01 (tag) > Group GAL 1 [15 & 16 switch ports] (unidentified) > ESXi host LAG (default configuration for VLAN Trunking 0 - 4094) > Distributed port group nec VLAN #100.

  The problem is that I have restart the physical switch and Firewall [Physics] but not the host ESXi, DS or virtual machines. Because the VMs system had been on before configuration changes their network cards were shooting a null IP and without release and renew their, they have been stuck without the IP DHCP VLAN address. I didn't enter the VMs (2012r2 server operating system) system and disable the network adapters and then enable them. They then shot the IP address of the subnet assigned to the VLAN.

  Stupid mistake but at least it is resolved.

• Cisco asa active multiple interfaces on a single switch without configuration of vlan switch.

  I was wondering if there is a work around on cisco asa to have 2 interfaces vlan on a switch. The reason I ask I have a cisco asa 5505 and a dell switch that does not support the configuration of VLANs. I set up 2 interface vlan on a cisco asa and when two interfaces are active my internet drops frequently. I was wondering if there is nothing to configure the asa cisco to make this thing work. Thanks in advance...

  Assuming that Dell switch at least linking several interfaces of the ASA to the Dell should translate all media spanning tree protocols, but a bet covering the tree blocking State to avoid a tree covering loop.

  If the Dell does not support tree covering weight then you would be in very bad shape each broadcast packet would be will loop indefinitely and cause what we call a 'broadcast storm. "

  One way is not good and the other real harm.

• Configuration of VLAN Switch SF302 - 08 p

  I have the following Setup using two switches PoE SF302 - 08 p:

  1st floor

  =========

  SWITCH1 # <------->private network

  <------->public network

  2nd floor

  =========

  Switch #2 <------->private network

  ... public network (visible, but devices can't connect)

  I tried to do the config in the identical to the #1 switch #2 switch, but something still does not work.

  This is probably a configuration issue VLAN, or what?

  Thank you.

  Ken Watkins

  Hi Ken, the interfaces between switches must both vlan of the port.

  example of

  VLAN 1

  VLAN 2

  port 1 connects to port 1 of the second switch

  config t

  interface gi01

  switchport mode trunk

  switchport trunk allowed vlan add 2

  The ports between switches must be vlan unidentified native, all other VLAN Tag. In my example, 1u, 2 t.

  -Tom
  Please mark replied messages useful

• Configuration of virtual switch distributed to a display environment

  Are there specific practices around implementation of control network IO for a display environment. It is always better to separate the service console and keep on a standard virtual switch?

  I think that now its all what you're most comftorable with.  How many cards you like who could dictate how you would be put in place?

• What configuration of VLAN requires a switch connectivity defined as an access port?

  What configuration of VLAN requires a switch connectivity defined as an access port?

  By external switch tagging

• Configuration of vlan based SG200-8

  Hello world

  First of all, I m new to the company VLAN, but have some understanding of the general network configuration.

  I ve recently bought an SG 200-08 switch to separate traffic network (my home from the kids pc office)

  As seen by 'layout.png' I have an ASUS router which is connected to the switch on port 8. In addition I have desktop pc at home on the 7 port and the pc for children on port 2 (currently, this pc has a static IP address). Port 7 and 8 are on (default) vlan1 and port 2 is on vlan2 (test) - see 'vlans_one_and_two.png '.

  So my hypothesis is this: all the ports of the pc (1-7) are set up as 'Access' (for non - vlan hardware Manager) and the port of my router is "Trunk" (see interface.png) - in order for port8 in order to be member of vlan1 and vlan2 (but is my router able to identify communication trunk or forge would put in general?).

  If I move to vlan2 port2 all connections to the connected computer on which the port is lost. Even the switch is unable to ping.

  Maybe I ve got it all wrong - my installation requires a router connected between port 2 and the pc connected to the 2 port so that the installer to work? Or did I miss something in the configuration of the switch?

  Suggestions or comments are greatly appreciated.

  Kind regards.

  Kaare

  Hello

  First of all, thank you very much for all the information, it was very useful.

  Regarding your question, the problem is your router. I looked at the model number that you mentioned on the ASUS RT-AC68U schema, and although this seems to be a very capable router for functions more House, it is not capable of VLANS.

  The main component that you are missing is a router capable of VLANS, because it will perform the following functions:

  1. provide not only the default value (office) IP addresses VLAN, but also of the guess Vlan (Kids).

  2. it will take all the traffic of these two local area networks VIRTUAL on the Internet.

  The problem you are having now is that the switch is isolate children PC in a second VIRTUAL LAN, but once you do that, they even do not get IP addresses that the router knows nothing about the 2 VLANS.

  I recommend the RV130W router as close substitute of your Asus router. It is a small business router, which is capable of VLANS.

  I must say that your configuration of the switch is on site.

  I hope that this information has been useful.

• Configuration of the switch of the NAC

  Hello!!

  I bought a NAC server and a manager of the NAC, to centrally manage the vlan where users connect to based on authentication.

  I have several sites, but the NAC server will be at Headquarters.

  When a remote user authenticates, NAC must configure the user switch port for the vlan right.

  What is an out-of-band solution?

  Do need me a specific license for out-of-band?

  Best of look,

  Miguel Amaral

  Hello

  It's the same pattern: Yo uneed 2 licenses, one for the CAM and the other for CAs.

  One cam sets the number of cases you can add.

  That case defines how many users is supported.

  So either the CASE PAK has been lost, or never bought.

  In both cases, you will need to contact the entitiy that sold devices and demand for the PAK CASE.

  HTH,

  Tiago

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Configure the VLAN SG-200-26 2 p using WRVS4400N

  I would like to configure two VLANS on my SG-200-26 p switch. Using port 25 for VLAN 1 and port 26 for VLAN 2 from my WRVS4400N. Then assign each port (1-24) to one or the other VLAN.

  My router has 2 VLAN private Public (1) (2). Private is conifured wireless 1, 3 & 4 and private ports. Configured public port 2 and public wireless.

  Each work fine with different IP on each VLAN.

  Can I configure the switch as described above by using port 25 and 26? Y at - it instructions somewhere?

  PEOPLEVISON,

  Under the terms of a Port VLAN membership, you may need to select a port before joining VLAN...

  You can also us Port to VLAN if you wish. Just the VLAN at the top and click on Go. Then check the radio button for Untagged for the ports you want to in this VLAN.

  I have no problem with what you're trying to do. Please keep us updated.

  -Marty

• Configuration of vlan SG 300 - 28 p

  Hello

  I tried to Setup VLAN on a SG300 - 28 p, but they do not work.

  This is my setup:

  

  I want to Switch1 to have 1-10 ports to access the area demilitarized and 11-24 the LAN.

  Then I wan to add switch2-4 to expand access to the local network.

  Is this possible?

  I tested with cisco 2960 switches by saying just what ports forge have access to

  DMZ and LAN, but small business switches are different...

  I really appreciate the help!

  Hi Francisco, assuming that the 2960 worked and there was no difference in configuration then the problem would be that you have not added the VLAN to the trunk.  On a catalyst you do not configure the VLANS on a trunk, since all VLAN pass them. On SB switches, that you need to configure the VLANS on the trunk, otherwise only the VLANs native / default works.

  -Tom
  Please mark replied messages useful

• Configuration of the switch SGE2010P

  I am facing a problem during the installation of the switch SGE2010P with UC560. There are two switches in a SF300 and SGE2010P site. The SF300 works very well. But the SGE2010P switch is a problem. I connected the UC560 to the SF300 directly and connected SGE2010P to the SF300. In the two switches, all ports are trunk, not tagged vlan data and tag vlan voice. Switch SGE2010P is offline. Unfortunately, the phones don't work switch not which are connected to SGE2010P. Then I started shooting poorly, not marked all ports which phones are connected only to the voice vlan (vlan data excluded) and set the same ports to be the access port. Set the STP priority to zero. Now some phones work some are not. Can someone suggest what to do to fix this?

  Hi sham, by default the EMS classic switch short tree covering weight. This switch to RSTP. Secondly, you may need to manually set the fast port on all ports. Spanning interfaces of the tree then set the edge port on instead of auto.

  You said that all ports are given vlan not identified, voice vlan tagged, if that's the case, that your configuration of vlan is made. Assuming that the SF300 wearing exactly what you did on the EMS.

  In addition, you mentioned that the EMS is autonomous, check again please. If you use port 24 or 48 so that in the stacking mode, these ports do not work.

  -Tom
  Please mark replied messages useful

• Configure the vlan with SG 300 - 10 p and 520 SA

  Hi all

  Forgive my ignorance, but I need help with the basic configuration.

  For a small office, I bought an appliance of security SA520 (for future VPN with another remote desktop) and a switch of SG 300 - 10 p to connect 3 PCs and 3 IP PHONE. The SA 520 is the router. I have to configure 2 VLANS on the switch:

  VLAN2: DATA (for PC)

  VLAN3: VOICE (for IP PHONE)

  VLAN1: BY DEFAULT.

  How can I configure simply all ports?

  I would like to configure ports 1-4 on 5 to 8 ports and VLAN2, VLAN3 and G10 port is reserved for the SA520 router.

  I want to split VOICE and DATA network.

  I think I need to create a trunk on G10 to SA520...

  Can someone help me?

  Hi Julien,

  OK sounds like you use it vlan by default for network management and the vlan 2 for vlan3 for voice and data.

  I use a calculator for this, my SA520 is ready at the present time.

  Step 1   On the SA520 add vlan 2 and vlan 3 and label them voice and data respectively.

  

  Step 2. Allows you to use the switch port 4 on the SA520 as a port to shared resources to the SG-300.

  (my intent is to use vlan1 not tagged vlan tagged 2 and vlan tagged 3 on the uplink of the switch and the SA500.)

  To do this, I have to say the SA520 port 4 of the switch will be in trunking and not access mode.

  

  You will need to check the membership of vlan 2 and vlan 3 on switch port 4.

  Step 3.  Now add a few IPS to VLAN2 and VLAN3

  Step 4.  Create DHCP scopes if that is what is needed on the SA520

  

  So now I hope that we have the SA520 with the associated IPS VLAN1, VLAN2 and VLAN3

  We also have the switch port 4 as a network interface

  We are vlan1 reproducing unidentified and vlan2 tag and tag to the SG-300 switch vlan3.

  We do the opposite on the SG-300 switch.

  If you use G10 as the uplink to the SA520 you'll notice of default port 10 must already be in trunk mode.

  Switch ports G10 should be marked for vlan 2 and labelled for vlan3.  It will be, default Gi10 untagged for vlan1.

  Make sure you keep ports switch is correctly set up.

  Best regards, Dave

• Configuration of VLAN 'Wi - Fi comments' on ASA 5512

  I'm trying to configure a new vlan on my Cisco ASA 5512 running version 8.6 (1) 2.  This vlan will give access to AP Wireless 'invited' into my network.  I have the configuration of vlan comments through my switches, I am able to devote a switch port to 40 VLANS and acquire an IP address in the network 10.40.10.0/24.  Below is an extract from what I think is relevent to the config information.  I try to carry the traffic of comments on my ' outside' interface.

  Obvious to me miss me another command here.  Any help would be appreciated to greatling. If more running-config is required please advise.  Thanks in advance!

  _________________________________________________________

  interface GigabitEthernet0/1.40

  Description comments Wireless Network

  VLAN 40

  nameif guestwireless

  security-level 50

  IP 10.40.10.5 255.255.255.0

  Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1 (public IP address to X.X.X.X)

  access extensive list ip 10.40.10.0 guestwireless_access_in allow 255.255.255.0 interface outside

  guestwireless MTU 1500

  Access-group guestwireless_access_in in the guestwireless interface

  dhcpd address 10.40.10.50 - 10.40.10.250 guestwireless

  dhcpd dns 8.8.8.8 interface guestwireless

  guestwireless enable dhcpd

  ________________________________________________________

  Here is the part of the killing

  interface GigabitEthernet0/0

  ISP Interface Description

  nameif outside

  security-level 100

  To take

  interface GigabitEthernet0/0

  security level 0

  You do not want the more precarious with the higher level hehe safety interface

  Looking for a Networking Assistance?
  Contact me directly to [email protected] / * /

  I will fix your problem as soon as POSSIBLE.

  See you soon,.

  Julio Segura Carvajal
  http://laguiadelnetworking.com

• Virtual switch distributed on ESXi integrated Client Host

  Any plans to support vDS on the embedded host customer?

  If the distributed virtual switches are supported, I can't find how to set up their own good that I was able to configure virtual Standard switches.

  I haven't used client embedded myself yet, but in order to create or configure the vDS, you need to vCenter server you manage using vSphere Client/vSphere Web Client. vSS are by the host-based virtual switches that can be created and managed at the host level, so you can create those who use client Embedded or stand-alone vSphere client.

• migrate VM switch distributed to a standard switch

  Hello

  I need to migrate a virtual machine that is hosted on a cluster with switch distributed to another cluster with standard switches.

  This migration is possible when the virtual machine is turned off.

  By default, migrate function I get the following error message.

  Is there another solution?

  (without removing the network adapters)

  Thank you, Sven

  You can check that the host of the virtual machine's network configuration is running. He is a relevant portgroup created on the vSwitch Standard VM.