Configuration RAID - on Cisco UCS C 220 M3 with controller RAID UCSC-RAID-11-C220 problem.

Similar Questions

• Cisco UCS M81KR adapter is compatible with vSphere 5.5?

  Hello

  I can't find Cisco UCS M81KR adapter in the list of vSphere features 5.5 compatible hw. We vSphere 5.0 running on Cisco UCS B200 M2 blade with M81KR and are planning to upgrade to vSphere 5.5.

  Advice and suggestions will be greatly appreciated...

  Thank you!

  Hello

  It is supported by VMware HCL

  http://www.vmware.com/resources/compatibility/detail.php?deviceCategory=io&productid=10472&deviceCategory=io&keyword=m81&vioSolutions=Standard - IO devices & page = 1 & display_interval = 10 & sortColumn = partner & sortOrder = Asc

  Kind regards.

  Fred

• Cannot configure RAID on UCS C220 M4

  I'm trying to setup a new M4 C220 however the option press to enter the WebBIOS RAID never appears.  I also went in MMIC and the only options in there set up RAID 0, 1 or 10 However, we want to use RAID 5.  I tried to reinstall my readers and my RAID controller.

  Hi Cameron

  Which option RAID you bought?

  Is based on the RAID card, you can only create RAID 0, 1, 10

  http://www.Cisco.com/c/en/us/products/servers-unified-computing/UCS-c-SE...

  See Cisco UCS C220 M4 Rack Server Data Sheet

  Modular Cisco 12 G SAS RAID controller
  You can choose the Cisco 12 G RAID SAS controller, which plugs into a dedicated RAID controller card slot. This RAID controller supports RAID 0, 1, 10 (without option FBWC) and supports up to RAID 0, 1, 10, 5, 6, 50, 60 (with FBWC option).

• Configuring the Cisco UCS 5108 ports

  Hi all

  I'm new in the world of the Cisco UCS server and am setting up Cisco UCS 5108 blade server. The server has two Cisco UCS 6324 interconnections fabric I did the initial Setup on and I try to configure the ports for the blades. Looking through the various articles and tutorials after setting global policies, I see the whole world establishment of uplink and server ports. What I read the uplink ports are plugged directly into the switches (I work with two cisco nexus switches), and server ports are used to connect to the chassis.

  I wonder once the configured ports server what exactly are supposed to connect to? I assumed they would also connect to the switch nexus with the uplink ports. However, every time I set up the server ports and plug them in, the switch doesn't seem to have flooded and we lose all connectivity. If I unplug, the connection is restored almost immediately.

  The current configuration, that I work with is two ports uplink on each fabric interconnect (4 2 total in each switch of nexus), two server ports on each (4 2 total, in every nexus switch). The only other element connected to the nexus switches is a SAINT who will be configured as a boot and storage of the UCS 5108.

  Looks like you have a Mini UCS (6324), with 4-port 10 GB (each FI/IOM) with port QSFP 40 GB that can provide network connectivity linking rising, or if configured as a server port, could be used to connect to a server in a rack compatible Cisco UCS, or connect to a 5108 additional with IOM 2204XP chassis.  The blades installed in your initial 5108 chassis 6324 FI/IOM of housing have internal connectivity to the FIs / IOM without the need to configure ports 'server'...

  Please take a look at some of the visuals in the datasheet below.

  http://www.Cisco.com/c/en/us/products/collateral/servers-unified-computing/UCS-6300-series-fabric-interconnects/datasheet-C78-732207.html

  Unified ports can also be configured as a FC ports for connectivity of FC switch upstream or directly related to CF Storage processors.

  After having watched the datasheet, let me know if you have any other questions, and I'll try to address them.

  You'll not need actually configure ports such as ports 'server' unless you connect servers in a rack.

  Please configure any ethernet SFP type connected to your switches nexus upstream as 'network' uplinks.  I guess that you don't plan on a disjoint config layer 2 (where each FI has several sets of uplinks will different devices upstream, or the same device with different VLANS allowed on each link).    If you are, we can have a separate thread about how you need to configure that.

  Thank you

  Kirk...

• Cisco UCS configuration happy Pack

  Hello

  I downloaded the last available Cisco UCS Content Pack, listed as version 1.5.  I was able to import the content successfully Pack and see the dashboard properties, queries, alerts and retrieves the fields.  I am also able to select the Cisco UCS content Pack in a drop-down list in the section of the dashboards of the site (no data is displayed).

  However, I can't find anyway to configure the content Pack in my Center of interconnection Cisco UCS fabric, etc!

  Am I missing something?

  Do you mean Insight Log version 1.5 to version 1.5?

  Instructions for the UCS configuration can be found here: http://www.cisco.com/c/en/us/support/docs/servers-unified-computing/ucs-manager/110265-setup-syslog-for-ucs.html. You can add a review on the UCS on Solution Exchange application documentation.

• How to move a stand-alone series C of Cisco UCS managed service profile without losing any data?

  Hello

  We currently have a stand-alone series cisco C with 2012 Windows Server installed on the local disks.  We need to go this Cisco UCS server managed with a service profile, but can not lose existing data and the method of operating system boot.

  Does anyone know how to do this?

  Thank you

  Hi Adrien,.

  To be able to accomplish this together the local drive to 'any Configuration' policy this way UCSM won't overwrite the current raid on the server configuration.

  See the link below

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/SW/GUI/config...

  Let me know if that helps

• Cannot configure RAID 10

  UCS C220 M3S with 2008 M - 8i SAS raid PCI mezzanine card

  We just got a new server wiith this controller when trying to configure it with four (04) disks to a Raid 10 SAS... OOHH no RAID 10 could choose.

  I found a paper that says that controllers RAID 10 support:

  Link:

  http://www.google.com.pe/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&ved=0CDkQFjAA&url=http%3A%2F%2Fwww.cisco.com%2Fen%2FUS%2Fdocs%2Funified_computing%2Fucs%2Fc%2Fhw%2FC220%2Finstall%2Fraid.pdf&ei=_JmDUt7QEZPesASeqYLwBg&usg=AFQjCNEDExxiAHNdoxdwcD6VcVYk-ZL_LA&bvm=bv.56343320,d.cWc

  Please know what happends.

  Thank you.

  William Z.

  Hi William,.

  How do you set up the raid volume? You use the WebBios utility?

  If you use the WebBios utility you must make sure that you create two spans of two disks of each to be able to see raid 10 in option.  See the document below, it will show you how to configure raid 10 beginning on page 76.

  http://www.LSI.com/downloads/public/MegaRAID%20Common%20Files/51530-00_RevF.PDF

• Cisco UCS c240 can not have a partition outside the disk

  Hello

  I try to install ESXi 5.5 on a Cisco UCS of c240 M3.

  The local drive is a FlexFlash Raid 1 2 sd cards.

  When installing esx sees the local map 30 g.

  request the language, root password and when I click on install, it gives an error. (see attached files)

  This program has encountered an error: parted util, can't have a partition outside the disk

  I have 2 servers configured exactly, out of the box, same error... any idea?

  OK, so I tried with an older version of esx:

  ESXi-5.5.0-1746018-Custom-Cisco-5.5.1.3.iso

  and it seems to work for now (it's 28%)

• Cisco UCS C210 M2: PXE - E61: Media test failure, check cable of

  Hello

  I'm working on Cisco UCS C210 M2 servers. I got 10 146 GB SAS HD with LSI MegaRAID Raid Controller. I did run the Raid Controller and choose RAID6. After that I installed ESXi and it said to reboot the server. Now, when I restart the server I get the following error message:

  PXE - E61: Media test failure, check cable of

  PXE - M0F: Exit Boradcom PXE ROM

  Restart, and then select proper boot service

  or Insert Boot Media in some boot device and press a key

  Any suggestions how I can solve this problem.

  Thank you.

  You will need to go into the Bios of the controller LSI MegaRaid (Ctrl + H) and select the option of virtual drives on the left. When the virtual command window opens, you must select the drive (Raid Volume) on which you want your drive master boot and underneath there will be an option to set as your boot device. Apply and save.

• Cisco ucs with VMware 5 auto deploy

  Hello

  In our lab, I test with 5 VMware and Cisco UCS. We run UCSM 2.0 (1 m). I am now to test the auto hand deploy. I have auto configuration to deploy in VMware and it works (first of all, I had some problems with DHCP on windows which is solved in version 2.0 of UCSM (q)). vSphere gets deployed to the blade. When the blade (vShpere) wants to connect to vCenter I get an error of vCenter has enough licesing for this action. I loaded a lot of low-income VMware. When I create a virtual machine, it starts perfectly and apears in vCenter.

  I search on the internet for people who have the problem of the simailer, but could not find.

  Some body the same problem our help me?

  Thanks in advance,

  Robin

  Robin,

  This looks more like a VC related question (UCS) platform.  UCS has no effect on the functionality of licenses of the VC.

  If the host does not connect to the CR, how are you VMs to "start perfectly and appear in vCenter?

  Kind regards

  Robert

• How can Cisco ucs c220 m4 I start with 12g cisco sas controller? 2012 UEFI Server installation issues

  first time with cisco ucs c220 m4, check my photos

  You have a VD 11TB.

  Only way to start on this is by using UEFI.

  You need to activate UEFI in the boot order.

  Anything over 2 TB and more 4 K sector size readers require the UEFI boot option.

  BIOS will not process the VDs when manages UEFI.

  Kirk...

  Summary for those who seek a similar question:

  • Client a large VD created, 11TB
  • 2 TB and more, 4K sector drives, require boot UEFI + GPT, cannot use the legacy/MBR
  • To set startup to local HD option, that referenced the PCI-E Slot, the raid controller was in (HBA slot in this case)
  • UEFI mode, can't score a VD as "bootable disk / startup.
  • You will see not the VD/raid controller appear in the 'real' boot order during the OS install.
  • Once the installation of the OS compatible UEFI is made, it will create a UEFI boot to the operating system "Windows Boot Manager" entry in our case.
  • After the next reboot, if you check your boot order, you should see this UEFI OS boot manager entry.

• Dell TL4000 Tape Library on Cisco UCS 6120

  Hello

  We have Cisco UCS 5108 2 6120XP fabric of interconnection. We are running VMware on my Cisco blades. I have I need to connect my Dell TL 4000 LTO3 tape library this Cisco UCS so that I can configure a virtual machine with the EMC Networker software for backup of virtual machine data. When I connect the Cisco UCS library, it does not recoginize as tape drive.

  Please suggest how to set up the same.

  Thank you

  Amit,

  We do not support direct damage attach FC tape library to the FI currently.

  It may be a CF or CF storage end switch.

  . / Afonso

• Cisco UCS C240 M3 questions

  Hello

  I'm trying to install VMWare ESXi on a Cisco UCS C240 M3 and have a few problems.

  I configured the other servers before, but never a Cisco UCS.

  Firmware versions

  v1.5 (7 c) I could not load the KVM as I have a problem of Java. I am running Java v1.6.0_27 on my client.

  v2.0 (1B), the server kept by booting to the BIOS and seemed to ignore other startup options

  v2.0 (3d) the keyboard no longer works in KVM.

  Startup options

  There are a lot of startup options, and they seem to be configurable in many different places.

  I don't know where to start or what would be best practices?

  Nothing seems to work I'm waiting, and I did a lot of reading through documents, help, etc. online.

  My local Cisco support person on vacation so I hope someone can help me or guide me in the right direction.

  Thank you & best regards

  Steve

  Glad you found a way to fix it, don't forget to mark it as answered future users finding themselves in the same situation.

  -Kenny

• Service profile of the CISCO UCS for ESXi

  Do you need multiple boot LUN on the storage array for each host that you want to apply the service profile to? I'm just confused, let's say I have 12 blades that I want to designate as boot SAN for ESXi, y aura-t 12 profiles of separate service for each of them, and will need me 12 different LUNS on our storage? I am new to this and I just want to make it as clean as possible! Any help is appreciated.

  Hi Justin,

  You can have the same LUN ID for multiple service profiles, as well as the same target ID. However, your initiators will be different and you will need to configure the zoning on your switch upstream if you use the end host mode.

  Here is a good guide, review the basics and how to put in place.

  http://jeffsaidso.com/2010/11/boot-from-San-101-with-Cisco-UCS/

  Also here is an excellent guide to troubleshooting;

  http://www.Cisco.com/c/en/us/support/docs/servers-unified-computing/UCS-...

  Kind regards

• Configurations RAID P70 delayed?

  I configured a P70 RAID1 with two 512 GB SSD of PCIeNVMe on 12/23. The date of planned construction was delayed several times, the latest of 29/01/16. Has anyone received a P70 with still configured RAID?

  The initial order was placed on 12/23. The system was supposed to ship 1/9, but back push twice. 1/27 is now the new date. I'll check tomorrow because we are 1 day behind manufacturing in China.