Configuration VPN FVS336G V3 FW 4.3.3 - 6:

Similar Questions

• How can I configure VPN with XP? Is it necessary to use a third party software? It requires a static IP address? It is possible with a dynamic IP?

  I am interested in establishing a VPN for my computer.  I looked at some of the information to help Ms.  I'm missing something in the way of understanding how do or end the connection.

  You can configure VPN regardless of static or dynamic IP, both are possible. You can refer to:

  http://support.Microsoft.com/kb/314076

• LT2P configuration vpn cisco asa with the internet machine windows/mac issue

  Dear all,

  I have properly configured configuration vpn L2TP on asa 5510 with 8.0 (4) version of IOS.

  My internet does not work when I connect using the vpn. Even if I give power of attorney or dns or I remove the proxy

  It does not work. only the resources behind the firewall, I can access. I use the extended access list

  I tried also with the standard access list.

  Please please suggest what error might be.

  Thank you

  JV

  Split for L2TP over IPSec tunnel tunnel is not configured on the head end (ASA), it must be configured on the client itself, in accordance with the following Microsoft article:

  http://TechNet.Microsoft.com/en-us/library/bb878117.aspx

• Need help to configure VPN NAT traffic to ip address external pool ASA

  Hello

  I need to configure vpn NAT ip address traffic external pool ASA

  For example.

  Apart from the ip address is 1.1.1.10

  VPN traffic must be nat to 1.1.1.11

  If I try to configure policy nat or static nat ASA gives me error "global address of overlap with mask.

  Please, help me to solve this problem.

  Thank you best regards &,.

  Ramanantsoa

  Thank you, and since you are just 1 IP 1.1.1.11 Polo, the traffic can only be initiated from your site to the remote end.

  Here is the configuration of NAT:

  access list nat - vpn ip 192.168.1.0 allow 255.255.255.0 10.0.0.0 255.255.0.0

  NAT (inside) 5 access list nat - vpn

  Overall 5 1.1.1.11 (outside)

  In addition, the ACL crypto for the tunnel from site to site should be as follows:

  access-list allow 1.1.1.11 ip host 10.0.0.0 255.255.0.0

  Hope that helps.

• Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router

  Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device.

  Someone please please suggest me something as soon as POSSIBLE.

  Thank you

  CLI version:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml

  ASDM and SDM Version:

  http://www.Cisco.com/en/us/partner/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml

• Configuration VPN windows server 2012 essencial

  What policy I need to add in the game until I will configure the VPN in windows server 2012 essential? because when I install the remote access roles I received a message when done that mention me politics. later I activate access and remote access and I can't access the internet, I disable access and remote access to I can connect to internet from my server.

  There is no forums for Windows Server community.  Windows Server forums are on the Technet site.  http://social.technet.Microsoft.com/forums/en-us/home?category=WindowsServer

• WRT1900AC cannot configure VPN

  I CURRENTLY HAVE 2 WIRELESS ROUTERS AN ASUS RT-N56U WHICH WAS EASY to set UP WITH ExpressVPN. COMING TO EXPAND MY NETWORK & IMPROVE USING A LINKSIS WRT1900AC. UNABLE TO SET TO THE TOP OF THE SAME. BOTH ROUTERS ARE HARD CABLES TO THE ISP ROUTER & WILL BE POSITIONED AT DIFFERENT AREAS OF THE HOUSE FOR COVER. I HAVE THE ExpressVPN PAST & DETAILS USER password, LIST OF GLOBAL SERVER ADDRESSES & THEIR ADDRESSES IP CONCERNED.

  CAN SOMEONE HELP ME IN THE BASIC CONFIGURATION. I AM NOT AN IT WIZZ BUT YOU CAN FOLLOW THE INSTRUCTIONS ESPECIALLY WITH SCREENSHOTS SUPPORTED. HELP IS GREATLY APPRECIATED.

  OK gents,

  Answers very well. It gives me a lot to think so thank you very much.

  Temporarily, I currently have 2 routers connected switch wired to asus to linksys with the linksys being connected on the local network of the asus through the cable network. The asus is configured as L2TP that allows the details of user, password & VPN server. Use them in this way gives me the IP addresses associated with the address of the server used. This IP address is provided if connected to a router. Probably not the fastest or the best way but will suffice until I have work on your tech talk.  I have an ASUS RT - 68U (which has the VPN Client) available to replace the Asus RT - 56U to come. I can use the 56U on the edge of the property similar to the linksys. Trial & error prototyping will I hope make me it in the absence of knowledge or understanding.

  Can someone advise on potential pitfalls with the current configuration or plans for the future?

  Thanks again.

• BlackBerry 10 auto-configuration VPN connection on Wifi networks

  Dear all

  Soon-to-be owner of a Z10, I try to have a smooth start once it arrives. How would I go about establishing an automatic VPN connection to connect to certain Wifi (public, non-free)? Is it still possible?

  The VPN connection offer me free access to these networks, but it is quite annoying to always have to manually open the VPN when one of them is in scope.

  Thank you, Florian

  Hi floriparate and welcome to the community of BlackBerry Support Forums!

  Settings > network connections > Wi - Fi > saved, select the saved network and then add the VPN profile to configure auto-connect when it is connected to this network.

  This article will provide more information on the creation of a VPN on your BlackBerry Z10 profile.

  KB13469 - setting up a VPN profile on the BlackBerry smartphone

  Thank you.

• ASA5505 for configuration VPN Failover ASA-5510

  the best way to configure a second VPN tunnel by another carrier, to fail.  The two tunnels would go to the same network a Remote Site.   Is it possible to apply a metric or monitor the tunnel so that if the choice we're unavailable two choice would resume.   Can you point me to the example configuration preferably with ADSM?

  Hi Stewart,

  Please visit this link for the same thing:

  https://supportforums.Cisco.com/blog/150001

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• Cisco 1921 - how to configure VPN multiple Tunnels to AWS

  I have a router VPN Cisco 1921. I managed to create tunnel VPN Site to Site with AWS VPN Tunnel 1. AWS offers 2 tunnels, so I created another card Crypto and attaches to the existing policy. But the 2nd tunnel won't come. I don't know what I'm missing... is there a special setup that needs to be done to allow multiple IPsec vpn tunnels on the same physical interface? I have attached a picture and included the configuration of my router, if it helps.

  VPN - 1.jpg

  

  C1921 #sh run
  Building configuration...

  Current configuration: 2720 bytes
  !
  ! Last configuration change at 02:12:54 UTC Friday, may 6, 2016, by admin
  !
  version 15.5
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  hostname C1921
  !
  boot-start-marker
  boot-end-marker
  !
  !
  logging buffered 52000
  enable secret 5 $1$ jc6L$ uHH55qNhplouO/N5793oW.
  !
  No aaa new-model
  Ethernet lmi this
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  Research of IP source-interface GigabitEthernet0/1 domain
  IP cef
  No ipv6 cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  !
  !
  license udi pid CISCO1921/K9 sn FTX1845F03F
  !
  !
  username admin privilege 15 password 7 121A0C041104
  paul privilege 0 7 password username 14141B180F0B
  !
  redundancy
  !
  !
  !
  !
  !
  !
  !
  crypto ISAKMP policy 10
  BA aes
  preshared authentication
  Group 2
  lifetime 28800
  ISAKMP crypto keys secret1 address 52.35.42.787
  ISAKMP crypto keys secret2 address 52.36.15.787
  !
  !
  Crypto ipsec transform-set AWS - VPN aes - esp esp-sha-hmac
  tunnel mode
  !
  !
  !
  map SDM_CMAP_1 1 ipsec-isakmp crypto
  Description Tunnel 1 to 52.35.42.787
  defined by peer 52.35.42.787
  game of transformation-AWS-VPN
  PFS group2 Set
  match address 100
  map SDM_CMAP_1 2 ipsec-isakmp crypto
  Description 2 to 52.36.15.787 Tunnel
  defined by peer 52.36.15.787
  game of transformation-AWS-VPN
  PFS group2 Set
  match address 100
  !
  !
  !
  !
  !
  the Embedded-Service-Engine0/0 interface
  no ip address
  Shutdown
  !
  interface GigabitEthernet0/0
  Description connection Wan WAN - ETH$
  IP address 192.168.1.252 255.255.255.0
  automatic duplex
  automatic speed
  map SDM_CMAP_1 crypto
  !
  interface GigabitEthernet0/1
  Description of the connection to the local network
  IP 192.168.0.252 255.255.255.0
  automatic duplex
  automatic speed
  !
  IP forward-Protocol ND
  !
  IP http server
  local IP http authentication
  no ip http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  IP route 0.0.0.0 0.0.0.0 192.168.1.254 permanent

  !
  recording of debug trap
  host 192.168.0.3 record
  host 192.168.0.47 record
  !
  !
  Note access-list 100 permit to AWS Tunnel 1
  Access-list 100 CCP_ACL category = 20 note
  access-list 100 permit ip 192.168.0.0 0.0.0.255 any what newspaper
  Note access-list 101 permit to AWS Tunnel 2
  Note access-list 101 category CCP_ACL = 4
  access-list 101 permit ip 192.168.0.0 0.0.0.255 any logexit
  !
  control plan
  !
  !
  alias con exec conf t
  SIB exec show int short ip alias
  alias exec srb see the race | b
  sri alias exec show run int
  !
  Line con 0
  exec-timeout 0 0
  Synchronous recording
  line to 0
  line 2
  no activation-character
  No exec
  preferred no transport
  transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line vty 0 4
  privilege level 15
  local connection
  transport of entry all
  transportation out all
  !
  Scheduler allocate 20000 1000
  !
  end

  There should be no second tunnel.

  I use either a peer or the other, but not both at the same time.

  To display both at the same time, you need to use the Tunnel interfaces.  Amazon would have you sent pretty much the exact commands to copy and paste into.

• configuration VPN concentrator 3000 backup

  Hello

  Can someone tell me how can I take backup of my Cisco VPN 3000 series concentrator configuration?

  in GUI and command mode?

  I couldn't find any good document describing.

  Here is the link on how to Backup/restore configs and work with the file system.

  http://www.Cisco.com/en/us/docs/security/vpn3000/vpn3000_47/Administration/Guide/Fileman.html

• Configuration VPN Cisco RV110W.

  Hello

  We have a new RV100W router. I would like to use it for iPhone, PC and MAC for you connect via IPSec (QuickVPN) or PTTP.

  Whenever I go to the VPN configuration, it tells me that I need to set up a 10.x.x.1 network. How can I use VPN without doing?

  Thank you!

  Hi bndbrennan,

  Try to change the IP address, set up your VPN clients, and then restore the IP 192.168.1.1. The reason for which the router wants to change is because there are so many routers out there that have 192.168.1.1. If you always try to connect from one of these routers, the connection will fail. We see a lot of people that use 192.168.2.1 and it works fine.

• Configuration VPN - NAT - T support

  Hello

  A partner of business (BP) has the following requirements. I don't know which statements of config I need to use to ensure this successful connection

  Business (BP) needs partner complete the VPN tunnel on a firewall that is behind another firewall running NAT

  (BP) will create UDP 500 and UDP 4500 endpoints on the NAT firewall which is forwarded to the Firewall VPN termination.

  Because of this, the (BP) needs of my dissertation support encapsulation of ESP over UDP (NAT - T)

  My series of ASA5500 using the code (825) has the statements

  Crypto isakmp nat-traversal 21
  crypto ISAKMP ipsec-over-tcp port 10000

  VPN # match address BP_VPN crypto card
  VPN # set peer (peer_ip) crypto card
  VPN # game of transformation-AES_256_SHA crypto card

  IPSec-l2l type tunnel-group (peer_ip)
  IPSec-attributes of tunnel-group (peer_ip)
  pre-shared key (TBD)

  BP_VPN list extended access permit tcp host 10.x.x.x, 172.16.x.x eq (specified port) host
  BP_VPN list extended access permit tcp host 10.x.x.y host 172.16.x.x eq (specified port)

  NatExempt_VPN list extended access permit tcp host 10.x.x.x, 172.16.x.x eq (specified port) host
  NatExempt_VPN list extended access permit tcp host 10.x.x.y host 172.16.x.x eq (specified port)

  Please indicate whether these statements are sufficient and if not what else would be needed.

  You need not order

  crypto isakmp ipsec-over-tcp port 10000

  It is for the exclusive implementation that was used before NAT - T is available. You only need to nat-traversal active. For your ACL, using ports in there makes everything complicated. You should see if you can just use 'ip' here. If there is already configured on your ASA virtual private networks, then the config is probably ok. If this isn't the case, you must always configure ISAKMP and activate the encryption on the interface card.

• The router configuration VPN VTI adding a third site/router

  Hello

  I currently have two cisco routers configured with a connection to a primary WAN interface and a connection to an Internet interface. I have a VPN configured using a VTI interface as a secondary path if the primary circuit WAN fails. IM also using OSPF as a dynamic routing protocol. Failover works and itineraries are exchanged. The question I have is that if I want to put a third-party router in this configuration I just add another interface tunnel with the tunnel proper Public source and destination IP and new IP addresses for a new tunnel network.
  The current configuration of the VTI is below:

  Any guidance would be appreciated.

  Thank you

  Andy

  Router1_Configurtation_VTI

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key Cisco12345 address 0.0.0.0 0.0.0.0

  Crypto IPsec transform-set esp-3des esp-sha-hmac T1

  Crypto IPsec profile P1

  game of transformation-T1

  !

  interface Tunnel0

  IP 10.0.1.1 255.255.255.0

  IP ospf mtu - ignore

  load-interval 30

  tunnel source 1.1.1.1 Internet Source * Public

  2.2.2.1 tunnel * Public Destination Internet destination

  ipv4 IPsec tunnel mode

  profile P1 IPsec tunnel protection

  !

  Router2_Configuration_VTI

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key Cisco12345 address 0.0.0.0 0.0.0.0

  Crypto IPsec transform-set esp-3des esp-sha-hmac T1

  Crypto IPsec profile P1

  game of transformation-T1

  !

  interface Tunnel0

  10.0.1.2 IP address 255.255.255.0

  IP ospf mtu - ignore

  load-interval 30

  2.2.2.1 tunnel source * Source public Internet

  1.1.1.1 tunnel * Public Destination Internet destination

  ipv4 IPsec tunnel mode

  profile P1 IPsec tunnel protection

  Since this config is configuration of keys ISAKMP using address 0.0.0.0 0.0.0.0 is not required for a new encryption key isakmp with the new address of the site. Simply configure the VTI on the new router and one or both of the existing routers.

  One of the aspects of this application that should consider the original poster, that's how they want data to flow when the third-party router is implemented. With both routers, you have just a simple point-to-point connection. When you introduce the third-party router do you want one of the routers to use hub? In this case, the hub router has tunnels each remote Ray. Each remote RADIUS has a tunnel to the hub. Talk about communication talk is possible but will have to go to the hub and then out to the other remote. The other option is a mesh configuration where each router has VTI tunnel to the other router.

  HTH

  Rick

• Cisco ASA 5505 - Configuration VPN

  I'm trying to configure a VPN connection to allow customers access to the internal network. I have tried to use time Wizard VPN & repeatedly but customer connect but can get out to the internet and communicate with any host on the network. I tried to use a vpn in the 192.x.x.x or 10.10.1.X network dhcp pool but no luck.

  Comments or suggestions appreciated.

  What is the reason for these commands?

  NAT (outside) 0-list of access policyPAT

  NAT (outside) 5 10.10.1.0 255.255.255.0

  If this isn't spicific reason remove

  and put the following command:

  Permitted connection ipsec sysopt

  in global configuration mode to enable the VPN traffic to work around interface access lists

  Good luck

  If useful rates