Configure BEFSR41 V.2.1. to use as switch with ADSL ZTE Modem in Bridged mode

Similar Questions

• Can I use macbook pro with the lid closed in target mode?

  Hello

  I wish I could use my iMac 27 (Lat) 2015 as monitor for my Macbook Pro (mid-2013) so that the Macbook pro is closed.

  Two computers use El Capitan

  Is this possible?

  Jim P.

  A 2015 27 "iMac does not support display mode of the target.

  Use your iMac as a display with the target - Apple Support Display Mode

  iMac (retina 5K, 27 inches, end of 2014) and the iMac later models can be used as target Display Mode displays.

• Se3008 used as switch with wrt1900?

  All,

  Help a brother. :-)

  I want through my computers and screens.

  I have the ea6900 which has been replaced by the wrt1900.

  I need about 7 total Port.

  Is it better to get a Se3008 and connect it to the wrt 1900?

  Or can I use the ea6900 as a switch only?

  In addition, wiring, I need a crossover cable cat 6 for the wrt and switch (or ea6900) the I can use cat 6 right for computers and screens, Yes?

  I mix of Wi - Fi and wireless, but I want to associate as much as I can.

  Longer cable length can be 25 feet. Is this a problem with the Cat 6?

  Thank you for your comments.

  Hi marctronixx, because would need you 7 ports in total, it is best to get just a switch (SE3008) because for the EA6900 to act as a switch for the first router, you must plug the ethernet cable from one of the regular port of EA6900 to one of the regular ports of the WRT1900AC.

  This means that only one port from each of the two routers will be busy.  With the switch, there is no configuration that you do as well.

  As for wiring, pose no problems with it since the router ports are all intelligent ports already. The maximum distance for a good connection is 75 feet.

• How to use a switch with a variable null?

  Here's my current situation...

  I have a form that will take the information entered in the field "LEDIR" and divide by the information contained in the field "AMMUNITION".  I get errors when the form is loaded first because the "AMMO" field is empty and a problem of "division by 0".   I tried to solve the problem with a switch, but an not sure how to create a 'null' switch box.  This is what I have... any ideas on how I can put the second case it returns a '0' for a field null of AMMUNITION?

  var InvR = this.getField("LEDIR").valueAsString;
  var AmmoPk = this.getField("AMMO").valueAsString;

  switch (ammunition)
  {
  case '0 ':
  Event.Value = 0;

  break;

  case '[what to put here?]. :

  Event.Value = 0;

  break;
  by default:
  Event.Value = (Math.floor (InvR/AmmoPk))
  }

  any ideas on how I can configure the second case , it returns a '0' when the AMMUNITION field is empty?

  Use an empty string:

• I want to record with < alt > < s > in the Exact program online. This function does not work. This is the first time I use this program with firefox.

  Question
  I want to record with < alt > < s > in the Exact program online. This function does not work. This is the first time I use this program with firefox.

  edit, escaped mod < s > in order to avoid the line through question

  A web page can be defined a "accesskey" for an item. Unlike IE/Chrome/Safari, who use the Alt key only, Firefox requires pressing Alt and Shift to activate the element. In other words, try

  ALT + SHIFT + S

  and see if it works.

  I don't know of any way to change this so that the change is not necessary. There may be an add-on?

• How can I configure my Airport Extreme in Bridge mode (use the 3rd party router)?

  Data sheet:

  Airport Extreme - v 7.7.7

  Luma Surround Wifi 8

  I recently bought a wifi (luminance) surround system.  It comes with 3 routers that you place around your home.  Unfortunately I still have stains died in my house I'm looking to add my Airport Extreme (AE) to Luma network.  Is it as simple as plug the AE to the network (via Ethernet) and the bridge mode selection in the configuration of EI?

  I can see the AE of my iMac, and it is green.  How do you know that actually extend the wifi of my router Luma range?

  I searched the forum and all messages dealing with this are several years old.

  Thanks for your time...

  Basically, you want to create a mobile network with your Luma and AirPort Extreme routers. As you said, the extreme would need to be connected to the luminance by Ethernet and reconfigured as a bridge.

  In addition, the following are also required on the extreme:

  • Wireless mode: create a wireless network
  • The network name must be the same as that used by the Luma.
  • The type of wireless security and the password must match that of the luminance as well.

  To 'know' that the extreme extends the network of Luma, simply consult the BSSID value in the drop-down of OS X Wi - Fi. It must match the ID of the airport on your base station. Note: You must hold down the option key before clicking on the icon of the free Wi - Fi connection.

• Creation of Configuration in OWB 11 GR 2, using Scripts OMB +.

  Hi all
  Please help how to create a configuration pointing to another repository OWB using OMB scripting + Also how to change the location of active deployment for a module using Script OMB +.

  Hello

  Here's how you can add a new location for a module and adjust its configuration settings (ADC) here;

  OMBALTER ORACLE_MODULE "TGT_MOD" ADD REF LOCATION "ADC".
  OMBALTER ORACLE_MODULE 'TGT_MOD' SET VALUES OF PROPERTIES (DB_LOCATION) ("ADC")

  http://download.Oracle.com/docs/CD/E11882_01/OWB.112/e14406/chap3015.htm#DADFHBGE

  Not sure if that's what you're after? To create a new configuration pointing to your own control center;

  OMBCREATE CONTROL_CENTER "MYCC" SET PROPERTIES (etc...
  CONFIGURATION OMBCREATE "MYCONFIG".
  OMBCC "MYCONFIG".
  DEPLOYMENT OF OMBCREATE "MYCONFIGDEPLOY" THE REF "MYCC" CONTROL_CENTER VALUE

  See you soon
  David

• I can use my laptop with internet connection by cable, but cannot configure the wireless connection.

  Wireless Internet

  can use my laptop with internet cable is plugged in, but I am unable to set up a Wi - Fi connection, even though two other laptops in the House are Wi - Fi. Tried the convenience store who said there is a button on the front of the laptop that I push to turn on wireless on, tried that, but nothing is. I have an Acer Travelmate 2410, can someone help me?

  Hi Karldawkins,

  What operating system is installed on the computer?

  As the error message clearly indicates that the wireless switch is disabled on the computer. I suggest you consult the manual of the laptop and try to turn on the wireless switch.

  If you still experience the problem, then I suggest you to contact Acer support to enable the wireless switch.
  http://support.Acer.com/us/en/default.aspx

• How to configure the Windows speech recognition and use gtalk and gmail?

  Original title: Windows Vista speech recognition program the

  Trying to learn how to use the program of recognition of the window so that I can help a friend who has very high served as his hands. I'm getting the hang of it, but I need to know how to use Windows RV with gmail, because that's where we have been typing his e-mails for him, and is where he'd like to read his mail. On my own page of gmail, I am able to use the "numbers" for everything except actually typing in the main field, where he would actually type emails. Anyone able to help?  Max of TIA

  Hello
  • What happens when you click on the text box and dictate?
  • Also, try to use the HTML version of gmail and check.
   
  1. in Windows vista speech recognition.
  I've collected some articles from the Microsoft Knowledge Base that will help you in until the speech recognition settings.
  Windows speech recognition
  http://www.Microsoft.com/enable/products/windowsvista/speech.aspx
  Set up speech recognition
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-speech-recognition
  Setting speech options
  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-speech-options
  What can I do with speech recognition?
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-can-I-do-with-speech-recognition
   
  2 on the use of speech recognition on gtalk you can ask your question on the forums of gtak. Here is the link.
  Voice and video Chat
  http://www.Google.com/support/forum/p/chat/label?lid=18819d87e4369fa5&hl=en
   
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Problems with the new modem DSL and Linksys BEFSR41

  My Speedstream modem died and I had to buy a new modem.  At this time of year, it is difficult to find exactly what I wanted and I ended up buying a D-Link DSL - 2320-B.  I got the Linksys BEFSR41 (old version 1, I think) for years and it has always worked well.  I have problems to get an internet connection through the router.  With the modem connected directly to the network card, as now I have no connectivity problem.  I had to change the IP address on the Linksys BEFSR41 192.168.2.1, as the modem is 192.168.1.1, 192.168.0.1 as the old Speedstream.  I couldn't see a way to change the IP Address of the new D-Link.  I have my ICS TCP/IP set to auto obtain IP and DNS.  I was previously created for a fixed IP of * provided by the router.  Even with the setting on the router to "Obtain an IP address automatically", I can't to the internet with the router in the middle.

  Any help will be appreciated.

  Your modem is a combination of the modem and the router. The problem occurs when you try to connect another router behind this configuration and end up having 2 servers dhcp and nat 2 (for port forwarding and other issues, creating in some cases where even branded products use ip addresses will clash and devices will not connect at all when him are interconnected).

  To avoid the situation described above, it is recommended that you enable the full Bridge mode on the modem / router that you currently connected to the internet and let your new wireless router controls all the functions within your local network and the internet connection (you must enter all the details in the new router, including Internet service provider username and password).

• You can use my Mac with iOS

  You can use my Mac with iOS

  Hello ifixer2,

  Thank you for using communities of Apple Support.

  No, you need two or more Mac computers that meet the following requirements to use Back to My Mac:

  What you'll need

  To configure and use Back to My Mac, you need these things:

  • Two or more Mac computers that use the same account iCloud on OS X Lion v10.7.5 or later version.
  • A Terminal supported access AirPort (AirPort Extreme, AirPort Express or AirPort Time Capsule) or other Internet router that supports UPnP or NAT - PMP protocol, with the latest firmware available. AirPort base stations require version of firmware 7.6.1 or later for Back to My Mac.
  • Utility airPort 6.3 or later.
  • For screen sharing, a 300 Kbits/s-or-more rapid, bidirectional (high-low) Internet connection between computers. You may be able to use with slower connections to share files. If file sharing doesn't work as you think, check your settings and connections.
  • A firewall that allows remote connections. Some firewalls may prevent some back to my Mac connections. For example, when you're at home, don't maybe not able to connect you to your Mac at work. But when you're at work, you might be able to connect to your Mac at home. If you are not sure if the firewall will allow the back to my Mac connections, check with the network administrator for your organization.

  If you want to use an AirPort Extreme or airport Time Capsule to access files on a hard drive external, you need a Mac OS extended (journaled) formatted USB hard drive. When you use with Back to My Mac, your hard drive is displayed as the base under shared in the sidebar station Finder.

  Set up and use Back to My Mac

  Take care.

• How can I configure my Airport Express to mesh with new cable modem bridge mode?

  Time Warner sent me a new cable modem and my Airport express still flashing orange light. How can I configure the Airport express in bridge mode?

  You can simply do using AirPort Utility on your iMac or iPhone, as follows:

  • Run the AirPort Utility.
  • Select the AirPort Express Terminal and then, select change.
  • For a Mac:
    • On the network tab, change the router Mode to: Off (bridge Mode)
    • Select to update and allow the base station restart.
  • For an iOS device:
    • Select Advanced > DHCP and NAT
    • Change the router Mode to: Off (bridge Mode)
    • Select done and allow the base station restart.

  

• After the upgrade to El Capitan, I get "the scanner is attributed to ImageCapture. Using the scanner with TWAIN? What to say?

  I have XP Epson-610 and have scanned on it successfully for years. To date, but when tried to open I get the ap scanner, the scanner is attributed to ImageCapture. Using the scanner with TWAIN? ImageCapture does not work on El Capitan? What is TWAIN, a printer-scanner driver?

  Thank you.

  TWAIN is an old scanner interface. OS X now use ICA, Architecture (?) of Capture of Image.

  Never seen this message, but I guess that means Capture of Image is using the scanner, or is configured to use the scanner and it is not necessary for the third party software. You open picture Capture, or did the scanning software provided with the scanner by Epson?

• Source a current Sine using USRP N210 with Labview

  Hello

  I use USRP N210 with boards LFTX/RX for communication (electromagnetic Induction) cable and programming using LabVIEW and downloaded the drivers. I need to order the USRP to send a signal sine of 1 MHz through the barbed wire. I used the "Sine simulation block", but I'm not sure the block to which it must be connected to. Please let me know the steps or the blocks/screws that can be useful.

  Thank you.

  Hi Julie,.

  I think you need to use the open niusrp and log screw

  You don't need to use the configuration VI signal because I think that you can not set the frequency of the carrier on the Remora LFTX and LFRX.

  I think you can use the sinus blocks of generation as shown in the picture as an attachment.

  Thank you.

• WRT320N used as switch gigabit single - Question

  Hello friends,

  I use WRT320N a few days now and I'm happy with it so far! It has not overheated as many people reported and performance is also great (wifi and gigabit ports). I tested all the functions (NAT, Advanced Wireless Settings, Port Forwarding,... Access Restrictions) - all the great work, but I'm bit stuck on that easier - temporarily configure it as regular gigabit switch with an IP address: I put my cable WAN and LAN cables in ethernet ports 1-4. NAT, DHCP and firewalls are disabled in the router. I have the DHCP server in my network which is based on the MAC address IP address assignment. In "Setup" > "Basic settings" > "Router IP," I want to set up automatic configuration - DHCP, but it is not possible, so I just type the same IP address, it must obtain from the DHCP server (in this case 10.109.249.42). All ethernet ports 1-4 has the same MAC address (in this case, 00:25:9 C: 4 d: 16:86)?

  Everything works fine, my computer's IP addresses are correctly assigned (as well as wifi devices) from the DHCP server on my network, but I feel like WRT320N address is unaffected - the problem is that I can't connect to the router under http://10.109.249.42 administration. There is no IP restrictions for remote management. Any ideas?

  Screenshot of my "status" > "Local network".

  

  Routers Linksys WRT are not designed to be used as a simple access point/ethernet switch. That's why you won't find any configuration options you like for this configuration. You must configure a static IP address to the address LAN IP on the WRT. There's no other way. It's always a static IP address. The WRT will never get the address LAN IP of the server because it is designed to serve as a internet gateway and the DHCP server.

  It is clear to me why you are not able to access http://10.109.249.42/ while you are able to access the status page...

  Is the computer from which you are trying to access the router within the 10.109.249. *?