Se3008 used as switch with wrt1900?

Similar Questions

• Configure BEFSR41 V.2.1. to use as switch with ADSL ZTE Modem in Bridged mode

  I found a thread of 2009 who has a link that could help me with this configuration, but the link does not work.

  I have a Linksys BEFSR41 V.2.1 and need to set it up, so I can use it as a switch with our ZTE 831 ADSL Modem, which is in bridged Mode.

  The IP address of the BEFSR41 changed to avoid a conflict with the address IP of Modem ZTE ADSL, which is 192.168.1.1 to 192.168.2.1.

  If the PC is connected directly to the ZTE ADSL Modem, I can access the Internet and I can access the Menu of Configuration of Modem ZTE.

  If the PC is directly connected to the Linksys BEFSR41, I can access the Menu of Configuration Linksys.

  If the PC is connected to the Linksys BEFSR41, and which is connected to the ZTE ADSL Modem, I can't access the Internet, and I cannot Ping the ZTE ADSL Modem.

  Please give me a URL that indicates how the Linksys BEFSR41 should be configured to use as a switch with my ADSL Modem from ZTE in bridged Mode.

  My belief is that after I have the Linksys set up, I then plug the ZTE ADSL modem in the Linksys unit and use it to DHCP.

  DRM for your time and help! Lanny

  1. I never told of any change on the Advanced Routing page.

  2 do not connect the internet port for ZTE with this kind of configuration. You cannot use the internet port.

  3. Once you set that you can use the remaining LAN for ethernet devices ports in your local network.

• How to use a switch with a variable null?

  Here's my current situation...

  I have a form that will take the information entered in the field "LEDIR" and divide by the information contained in the field "AMMUNITION".  I get errors when the form is loaded first because the "AMMO" field is empty and a problem of "division by 0".   I tried to solve the problem with a switch, but an not sure how to create a 'null' switch box.  This is what I have... any ideas on how I can put the second case it returns a '0' for a field null of AMMUNITION?

  var InvR = this.getField("LEDIR").valueAsString;
  var AmmoPk = this.getField("AMMO").valueAsString;

  switch (ammunition)
  {
  case '0 ':
  Event.Value = 0;

  break;

  case '[what to put here?]. :

  Event.Value = 0;

  break;
  by default:
  Event.Value = (Math.floor (InvR/AmmoPk))
  }

  any ideas on how I can configure the second case , it returns a '0' when the AMMUNITION field is empty?

  Use an empty string:

• Using Windows XP with an access switched. How can I stop the network Dialer to invite the user connect even if I checked never dial a connection in Control Panel, then apply, then OK?

  Using Windows XP with an access switched. How can I prevent the network Dialer to invite the user connect even if I checked: never establish a connection to the Control Panel, then apply, then OK? She comes right back in a few minutes for: always connect by default. Help! Control panel Connections tab doesn't really seem to apply my change to never establish a connection right back to always make the default connection. What else is there to do?

  Hi Richard,

  You did it all change hardware or software on your computer before this problem?

  You can follow this link & check if the problem persists:

  Network connections and remote access troubleshooting

  Hope the helps of information.

• I don't understand why I can't login my account using mozilla but with googlechrome fb, I am able to do... Mozilla can load the fb site but cannot access my fb account... I'm uncomfortable with the use of mozilla as my browser... pls help thanks

  I don't understand why I can't login my account using mozilla but with googlechrome fb, I am able to do... Mozilla can load the fb site but cannot access my fb account... I'm uncomfortable with the use of mozilla as my browser... pls help thanks

  • "Clear the Cache": Tools > Options > advanced > network > storage (Cache) offline: 'clear now '.
  • 'Delete Cookies' of sites that cause problems: Tools > Options > privacy > Cookies: "show the Cookies".

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the Add-ons is the cause of the problem (switch to the DEFAULT theme: Tools > Modules > themes).

  • Makes no changes on the start safe mode window.

  See:

  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox

• I can use my laptop with internet connection by cable, but cannot configure the wireless connection.

  Wireless Internet

  can use my laptop with internet cable is plugged in, but I am unable to set up a Wi - Fi connection, even though two other laptops in the House are Wi - Fi. Tried the convenience store who said there is a button on the front of the laptop that I push to turn on wireless on, tried that, but nothing is. I have an Acer Travelmate 2410, can someone help me?

  Hi Karldawkins,

  What operating system is installed on the computer?

  As the error message clearly indicates that the wireless switch is disabled on the computer. I suggest you consult the manual of the laptop and try to turn on the wireless switch.

  If you still experience the problem, then I suggest you to contact Acer support to enable the wireless switch.
  http://support.Acer.com/us/en/default.aspx

• How to use a switch connected to the DAQ card as a source of events in a Structure of the event

  Is easy using a switch on the front panel as a source of events. However, I like to use an external switch electrician on my card for the acquisition of data (NI PCI-6229) as the event source in the Structure of the event. Can anyone help?

  Happy New year to you too!

  Attached is an example in BT 8.5

  • It uses the time-out loop (running every 100ms) to simulate your reading of the data acquisition card.
  • A shift register is used to keep track of the previous value of the switch.
  • When a change of the switch is detected, the user event is raised and the display will show the new State.

  Running the vi with activated highlight performance can be useful.

  Steve

• WRT320N used as switch gigabit single - Question

  Hello friends,

  I use WRT320N a few days now and I'm happy with it so far! It has not overheated as many people reported and performance is also great (wifi and gigabit ports). I tested all the functions (NAT, Advanced Wireless Settings, Port Forwarding,... Access Restrictions) - all the great work, but I'm bit stuck on that easier - temporarily configure it as regular gigabit switch with an IP address: I put my cable WAN and LAN cables in ethernet ports 1-4. NAT, DHCP and firewalls are disabled in the router. I have the DHCP server in my network which is based on the MAC address IP address assignment. In "Setup" > "Basic settings" > "Router IP," I want to set up automatic configuration - DHCP, but it is not possible, so I just type the same IP address, it must obtain from the DHCP server (in this case 10.109.249.42). All ethernet ports 1-4 has the same MAC address (in this case, 00:25:9 C: 4 d: 16:86)?

  Everything works fine, my computer's IP addresses are correctly assigned (as well as wifi devices) from the DHCP server on my network, but I feel like WRT320N address is unaffected - the problem is that I can't connect to the router under http://10.109.249.42 administration. There is no IP restrictions for remote management. Any ideas?

  Screenshot of my "status" > "Local network".

  

  Routers Linksys WRT are not designed to be used as a simple access point/ethernet switch. That's why you won't find any configuration options you like for this configuration. You must configure a static IP address to the address LAN IP on the WRT. There's no other way. It's always a static IP address. The WRT will never get the address LAN IP of the server because it is designed to serve as a internet gateway and the DHCP server.

  It is clear to me why you are not able to access http://10.109.249.42/ while you are able to access the status page...

  Is the computer from which you are trying to access the router within the 10.109.249. *?

• What are the bare minimum commands to get a stack of PC6825 3 - switch with inter switch Link Aggregation?

  I am brand new to PowerConnect switches, even though I am familiar with the concepts of VLANS, aggregation of links and spanning tree.

  I am on a deadline to get some new ones installed 6248 in our baskets and get them functioning as a stack. What are the bare minimum commands for:

  • Three switches in a stack (master/Eve/member)
  • 2 ports grouped between each (total redundancy) switch with loops WITHOUT switching

  All the switches are running firmware v3.3.9.1 (January 2014).

  Thank you

  The range of interface Ethernet 1/g1-1 / g2 allows you to select the ports you want in the channel of the port. Page 293

  Channel-group 1 Auto mode to create 440 lacp lag page

  Select the Group of channels with interface port-channel 1

  Switchport page 601 in trunk mode

  Switchport trunk allowed vlan [VLAN you use]

  http://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/PowerConnect-6248_Reference%20Guide_en-us.PDF

• Does anyone use this switches in a data center?

  I have an interest in the switches of SG-300 or SG-500 small businesses for small and moderate use.

  These are rack switches, but my question is if someone is actually using them in a rack of data center with public servers rather than catalysts?

  I understand that they are small business units, but they would hold the heat, vibration in a rack? How do they practice?

  I have an older catalyst, it costs less than new now that some of this small business ones, but I really need gigabit for internal LAN traffic ports and my DC tells me none has this unit to small businesses in their DC, it is not normal to use because they are not high-performance switches. IM worried to go small businesses who are actually Linksys device and not Cisco. I have some Linksys devices for personal use and at home and they are still in years. But I Don t know how they perform outside of this environment. I need to stay under $ 1000 per switch.

  They would fail in a few months? Can be clustered (2 switches) so if one fails the other take the network up until I have replace the failure? If so, I could take the risk, but one dying switch would be a disaster.

  My needs are low speed gigabit between the servers for backup and storage, but usually less 50 Mbit on the public Wan. These switches are really only for small office use or if they work very well with the servers in an institution? If so, I'd love to hear some real experiences, everyone I ask most of them said not to go with the switches, but then why are they still rack? They can´t be this bad or that they are not really designed for 24/7 usage?

  I'd appreciate some experiences with the amount of traffic you are passing on them and for how long (months) because I Don t know anyone use so far in a remote installation.

  Catalyst has shared backplanes and ASICS. SX300 and SX500 series does not work. If you do not need things like the protocols of the road (BPG, OSPF, IS - IS), VTP, CEF then these switches are very good.

  The switch has generally not hardware failure unless it is due to external voltage problems. A real failure, the MTBF is probably 4 or 5 years old, and I say this because the SX300 was not of the most and I've honestly never seen a die with the exception of power problems (storms, power surges, etc.). I saw ports to die only once and a while but that does not matter much because the switches are hardware to life with replacement free advanace...

  If you plan to use these switches as a Ridge with high throughput, especially in layer 2, I seriously doubt you'll break this thing.

  I am not yet sold on the robustness in environments of layer 3 but as a core for sub 300 people is a good switch. In response to another concept, the SX500X switches supports VRRP.

  -Tom
  Please mark replied messages useful

• Operating a SG200-08 switch with case removed.

  I'll put a SG200-08 (8 port switch) within a 2U rack mount chassis.

  To improve cooling I thought I'd take off the outer case.

  Is there or are there problems with the help of the switch with the cover removed?

  Thank you

  Glen

  Hi Glen, the first question would be, the warranty is voided and you are not entitled to any help. The second question is static electricity and environmental concerns. The third question would probably be your property insurance.

  He is strongly against the recommendation to alter or change these units.

  -Tom
  Please mark replied messages useful

• Are there plans for the new ESW 500 models switch with PoE capability?

  I know that current models of ESW 500 switch don't have enough capacity to power all the switchports to 15.4, even if the ESW-540-8 p model has almost enough capacity to power all the switchports to 15.4.

  Reasons why new ESW 500 switch with PoE capacity are necessary:

  • The existing PoE 500 ESW switches have not always enough when these devices are deployed with the UC500:
    • 7945, 7965 and 797 x phones
    • series phones (not yet supported with the SBCS solution) 9900 and 8900
    • PVC2300 Surveillance Cameras
    • AP541N access points
  • The UC560 comes with all the PoE ports and requires at least an ESW switch be deployed
  • Version 48 ports gigabit switch ESW is currently available only in the version not PoE, and we need a version of 48 gigabit ports for users of the UC560 solution.

  Existing ESW 500 switch PoE capabilities are:

  • ESW-520-8 P: 60W
  • ESW-540-8 P: 120W
  • ESW-520-24 P: 180W
  • ESW-540-48P: 380W
  • ESW-540-24 P: 280W

  PoE of ESW 500 switch capabilities supporting 15.4 full power on all PoE PoE ports are:

  • 8 port: 123.2W
  • 24 port: 369.6W
  • 48 port: 739.2W

  Are there plans to release the new ESW 500 switch models increased capacity, enough to supply the full 15.4 to all PoE ports with PoE?

  Hi John - Thank you for your participation in the small community of business support. I talked to our switch product manager and want to share his response.

  / * Style definitions * / table. MsoNormalTable {mso-style-name: "Table Normal" "; mso-knew-rowband-size: 0; mso-knew-colband-size: 0; mso-style - noshow:yes; mso-style-priority: 99; mso-style - qformat:yes; mso-style-parent:" ";" mso-padding-alt: 0 to 5.4pt 0 to 5.4pt; mso-para-margin: 0; mso-para-margin-bottom: .0001pt; mso-pagination: widow-orphan; do-size: 10.0pt; do-family: "Times New Roman", "serif" ;} "}

  We have taken the conscious decision to deliver PoE as ESW and other switches for small businesses for several reasons:

  • Endpoints PoE more attract a lot less than the 15.4 W maximum power. Most IP phones are below the range of 7W.
  • A typical deployment would most PoE devices connect to a switch.
  • For these reasons, the ESW is not burdened cost with the PoE feature which would not be used most of the time.
  • All ports are still able to PoE you can connect up to 24 devices PoE Switch 24 ports to any point in time, as long as the handset is in the title of the budget.
  • Therefore, given that these products are intended for small business and the price is an important factor, we opted for this approach.

  We do not have a product at full power on all ports in the Cisco Small Business portfolio, except in the arena of 8 channels. Within Cisco, Cisco Catalyst products support this today.

  Thanks again for the question,

  Stephanie Reaves

  Cisco Small Business

• / close the switch with the media player 12 on windows 7 32-bit o/s

  I try to use the /close switch with media player 12 on windows 7 32-bit o/s, the media player opens and plays the file but does not close after the reading of the file.

  I expect that the /close should work when used in conjunctino with the /play after reading the site--> http://support.microsoft.com/KB/241422

  Some commands I tried:

  Start/min Mplayer2.exe /play/c:\alert.wav nearby

  Start/min /play/c:\alert.wav nearby wmplayer.exe

  This same exact command is currently working on Windows XP. Appreciate any help on this.

  Thank you

  Kalyan

  Hi Kalyan,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  TechNet Forum

  http://social.technet.Microsoft.com/forums/en/iTCG/threads/

  I hope this helps.

• Using ProSite existing with the new account CC

  I currently have a Behance ProSite I pay for separately each month.  I think about the purchase of a membership of creative cloud and see a ProSite is included in the subscription.

  Can I use my existing with my new account CC ProSite?

  If so, what happens to my current monthly payments I have do to Behance?

  Would like to have this issue resolved before I have buy my CC membership as my ProSite is the main site of my company, I can't lose it or have done anyway by signing up to CC.

  Hello

  "Can I use my existing with my new account CC ProSite?" - Yes you can! You should just make sure that your ProSIte account is associated with the e-mail address that you used to pay for creative cloud (if this isn't the case, you can switch what Adobe ID associated with you here: https://www.behance.net/portfolio/promote )

  "If so, what happens to my current monthly payments that I do to Behance?" - you not will be charged again. (You can always send us at help.behance.com to make sure)

  Thank you!

• Throw after error while using the switch inside the ProductLookup... ?

  Hi all
  
  When you use droplet of switch with release of ProductLookup droplets, throws following error...
  
  code-
  
  < name dsp:droplet = "/ atg/commerce/catalog/ProductLookup" >
  < name = 'elementName' value 'product' = dsp:param / >
  < name dsp:param = 'id' param = "productId" / >
  < name dsp:oparam = "output" >
  Product is new? -param = "product.new" dsp:valueof / >-here it gives false... but the error happens when you use droplets of switch
  < name dsp:droplet = "/ atg/dynamo/drop/Switch" >
  < name dsp:param = "value" value = "true" >
  < name dsp:oparam = "false" >
  This product is not new
  < / dsp:oparam >
  < dsp:oparam name = "true" >
  This product is new
  < / dsp:oparam >
  < / dsp:droplet >
  < / dsp:oparam >
  < / dsp:droplet >
  
  
  errorMessage-
  
  
  2012-11-29 19:44:54, ERROR 312 [org.apache.catalina.core.ContainerBase. [JBoss.Web]. [localhost]. [chi]. [jsp]] Servlet.Service () for servlet jsp threw exception
  org.apache.jasper.JasperException: product/inc/product_inventory.jsp(96,3) according to the TLD, dsp:param of the tag must be empty, but is not
  
  
  
  Thanks in advance,
  Laurie Bovilla
  
  Published by: Laurie B on 29 November 2012 06:22

  You should do like this in the drop of switch:

  
  
  
  
  Product is new? - -Here is giving fake... but the error happens when you use droplets of switch
  
  **
  
  This product is not new
  
  
  This product is new