Configure N9010A attenuation in mode EPI
Hello
With CVI 2009 IVI Driver for the Agilent N9010A, I'm measuring spurius...
in order to better search criteria, I need to apply the attenuation of 0 dB to the instrument.
I can't find the API related to the mode of the SPUR and mitigation and the APU 'agmxa_ConfigureElectricalAttenuation' in the Setup menu only apply to the
SCAN mode.
any suggestions?
Cordially Ofir
Hello ofirga,
I downloaded the IVI driver for the device you specified and noticed a few function calls from the IPS Configuration. I found these slot tree library instrument under Configuration > measurement Setup
Hope that helps!
Tags: NI Products
Similar Questions
-
Cisco RV220W IPSec VPN problem Local configuration for any config mode
Dear all,
I need help, I am currently evaluating RV220W for VPN usage but I'm stuck with the config somehow, it seems that there is a problem with the Mode-Config?
What needs to be changed or where is my fault?
I have installed IPSec according to the RV220W Administrator's Guide. Client's Mac with Mac Cisco IPSec VPN, I also tried NCP Secure Client.
I have 3 other sites where the config on my Mac works fine, but the Cisco VPN router is not.
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: remote for found identifier "remote.com" configuration
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: application received for the negotiation of the new phase 1: x.x.x.x [500]<=>2.206.0.67 [53056]
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: early aggressive mode.
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: RFC 3947
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: CISCO - UNITY
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: DPD
2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: for 2.206.0.67 [53056], version selected NAT - T: RFC 39472013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: floating ports NAT - t with peer 2.206.0.67 [52149]
2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT - D payload is x.x.x.x [4500]
2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT - D payload does not match for 2.206.0.67 [52149]
2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT detected: Peer is behind a NAT device
2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: request sending Xauth for 2.206.0.67 [52149]
2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: ISAKMP Security Association established for x.x.x.x [4500] - 2.206.0.67 [52149] with spi: 1369a43b6dda8a7d:fd874108e09e207e
2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: type of the attribute "ISAKMP_CFG_REPLY" from 2.206.0.67 [52149]
2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: connection for the user "Testuser".
2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: type of the attribute "ISAKMP_CFG_REQUEST" from 2.206.0.67 [52149]
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: ignored attribute 5
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: attribute ignored 28678
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode=>
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode
2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: attribute ignored 28683
2013-03-07 01:56:07: [CiscoFirewall] [IKE] INFO: purged-with proto_id = ISAKMP and spi = 1369a43b6dda8a7d:fd874108e09e207e ISAKMP Security Association.
2013-03-07 01:56:08: [CiscoFirewall] [IKE] INFO: ISAKMP Security Association deleted for x.x.x.x [4500] - 2.206.0.67 [52149] with spi: 1369a43b6dda8a7d:fd874108e09e207e
Hi Mike, the built-in client for MAC does not work with the RV220W. The reason is, the MAC IPSec client is the same as the Cisco VPN 5.x client.
The reason that this is important is that the 5.x client work that on certain small business products include the SRP500 and SA500 series.
I would recommend that you search by using a client VPN as Greenbow or IPSecuritas.
-Tom
Please mark replied messages useful -
The computer will be used only to access online catalog in my library. I need to remove the location toolbar, but keep the "back" button and the "home" button. If I use the Kiosk mode, I do not have the "previous" button. I can set it up so that I have the buttons but not the URL, but a user could right-click on the menu bar and reactivate the address bar. I need to stop them from doing it.
Thank you!Users can always bring up an address bar with the shortcut Ctrl + L if this bar is hidden.
One possibility is to hide the toolbar elements and elements of (context) menu with code in userChrome.css below default @namespace.
Customization files (interface) userChrome.css and userContent.css (Web sites) are located in the chrome folder in the user profile folder.
@namespace url("http://www.mozilla.org/keymaster/gatekeeper/there.is.only.xul"); /* only needed once */ #openLocation, #urlbar-container, #CustomizeToolbarWindow, #toolbar-context-menu { display:none!important; }
-
Play with Oracle SQL developer configuration and its debug mode
Greetings from a newbie, ask simple questions:
1. I'm trying to run sql scripts using sql developer without actually connecting to the database, which makes a fake link in order to check if the syntax of the scripts is correct. Can I do this?
2. Furthermore, I try to play with its CONF file, and I have a difficulty to understand the language that is using. What language is this? I can only guess "sqldeveloper - debug.conf ' is performed when I put ' IncludeConfFile sqldeveloper - debug.conf" in sqldeveloper.conf. But I don't really know how these configuration files. Could you give me some tips to learn this?
Best regards
ValerieNo, Developer SQL does not parse the SQL statements, just them sends to the server and presents the results with you.
As for the syntax of the configuration files, no idea. You might have more luck the {forum: id = 260} forum.
-
System configures stuck on selective mode
I used selective startup to perform a clean boot but now can't go back to a normal startup. Whenever I chose normal and click on apply it becomes selective. From elsewhere if I choose selective and check all and go to services and allow any, is it the same as usual?
I resolved to myself. Shot on an item under Startup tab was disabled permanently. It's a protection site software I had installed myself so I uninstalled, once I did that I was able to return to normal startup. I then reinstalled the software and everything is fine,
-
Original title: frozen configuration page
My laptop running windows xp pro was fine, when I went to bed last night, but this morning I woke and went to use the lt and it started as usual but then in a mode options regurly windows open or to last working configuration, or 3 safe mode options. And no matter what I choose, it keeps restart and return to this page and has continually repeated the same steps over and over again... someone can please help me with this?
It seems that your XP hangs for some reason any...
Why do we know almost nothing about your system (except a laptop with XP Pro)? I know this isn't your fault...
Please answer these questions and to implement the following:
Provide information on your system, the better you can:
What is your system brand and model?
What is your Version of XP and the Service Pack?
Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..
The question was preceded by a loss of power, aborted reboot or abnormal termination? (this includes the plug pulling, buttons power, remove the battery, etc.)
The afflicted system has a working CD/DVD (internal or external) drive?
You have a genuine XP installation CD bootable, which is the same Service as your installed Service Pack (this is not the same as any recovery CD provided with your system)?
If there is a problem starting, XP is configured to automatically try to start again and you can stuck in a loop not being able to go beyond the screen boot options, or none of these startup options you choose will work only.
Sometimes, when XP has a problem starting or falls down and tries to start again, it will give you a "short" menu of boot options and none of them will appear to be good to get your system going again. You have tried them all!
The options are similar to the Advanced Boot Options menu XP, but the only option that you need (disable automatic error system reboot) are not offered, because XP went too far during the boot process and offers a limited number of boot options.
If this is the case, you must call Options menu advanced boot yourself until you do not see the option:
Disable the automatic restart in the event of system failure
When you get the XP Advanced Options correct start menu you want to see, he has options on it like these:
Safe mode
Safe mode with networking
Safe mode with command promptEnable Boot logging
Enable VGA mode
Last good Configuration known (your most recent settings that worked)
Directory Services Restore Mode (Windows domain controllers only)
Debug mode
Disable the automatic restart in the event of system failureStart Windows normally
Reset
Return to OS Choices MenuYou need to choose in this menu is the option:
Disable the automatic restart in the event of system failure
Then if XP does not start normally, you will see an error screen with information and clues about the problem and then you can decide what to do next.If you do not see the automatic restart on system failure option turn it off, you must reset your system and start typing the key F8 on the keyboard until you see her disable automatic restart on system failure option.
If you miss the window of opportunity F8, you must try again and start tapping the F8 key with more urgency (earlier and more frequently) until you see disable automatic restart on system failure, and then select.
You must keep trying the F8 menu until you see disable automatic restart on system failure option, and select it.
If your system has a Blue Screen of Death (BSOD), we need to know what the screen says:
Here's a BSOD example showing information you provide:
http://TechRepublic.com.com/i/tr/downloads/images/bsod_a.jpg
Send for the nose and the Red arrows (3 to 4 lines total).
Send all * line STOP message since there are clues in the 4 parameters.
If it looks like there is some kind of name listed in the STOP message file, send this line also.
Ignore the boring text unless it seems important to you. We know what a BSOD looks like, we need to know what your BSOD looks like.
Answering queries and results report of the disable automatic restart on system failure screen and you can decide what to do next.
-
No command ' configure terminal ' privilege mode
Hi guys,.
I'm seting up a 1250G AP Cisco via port console for the first time, something very strange, I can not find command "configure terminal" under privileged mode. Does anyone know why? Thanks in advance.
AP0026.994C.e39c #sh privilege
Current privilege level is 15
AP0026.994C.e39c #?
Exec commands:
CD change current directory
Disable the Reset functions
Manage the clock system clock
Crypto encryption related orders.
debug debugging features (see also "undebug")
Delete Deletes a file
List of files on a file system dir
disable the Turn off privileged commands
dot1x IEEE 802. 1 X commands Exec
turn on the turn on privileged commands
exit from the EXEC
fsck Fsck a file system
help Description of the interactive help system
led functions LED
locking of the terminal
Connection connect you as a particular user
Logout Exit from the EXEC
OfficeExtend AP lwapconfig configurations
LWAPP lwapp exec commands
mkdir create new directory
monitor various system events monitoring
more display the contents of a file
Name the connection-name an existing network connection
No function to disable debugging
Send echo ping messages
Working Directory current pwd display
RADIUS radius exec orders
Release to release a resource
Stop reload and perform a restart cold
Rename rename a file
renew renew a resource
rmdir remove the existing directory
rsh to execute a remote command
Register early to save the battery raise_interrupt_level
Send a message to other TTY lines
setting system Set Set (no config)
Show Show running system information
SSH open a secure shell client connection
SYSTAT display information about the terminal lines
terminal Set terminal line parameters
Test Test subsystems, memory and interfaces
Traceroute-Trace route to destination
undebug disable debugging functions (see also 'debug')
software upgrade upgrade
Check check a file
where the list of active connectionsAP0026.994C.e39c ter #config
^
Invalid entry % detected at ' ^' marker.AP0026.994C.e39c #.
AP0026.994C.e39c #sh worm
Software Cisco IOS, C1250 Software (C1250-K9W8-M), Version 12.4 JA (21 a), RELEASE SOFTWARE (fc1)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Updated Tuesday 8 June 09 16:49 by prod_rel_teamHello
The reason why you do not have the config t prompt is because you have a LWAPP access point. LWAPP ap do not have a config t, as the access point's configuration of the WLC.
If you find the useful rate please post... Thank you!
-
Hi all
I'm using the Oracle 11 g with Windows 32-bit platform.
My database was in noarchive mode.
I'm doing a switch a check to my way USE_DB_RECOVERY_FILE_DEST logs are generated.SQL> SELECT LOG_MODE FROM V$DATABASE; LOG_MODE ------------ NOARCHIVELOG SQL> shutdown immediate Database closed. Database dismounted. ORACLE instance shut down. SQL> startup mount ORACLE instance started. Total System Global Area 535662592 bytes Fixed Size 1334380 bytes Variable Size 306185108 bytes Database Buffers 222298112 bytes Redo Buffers 5844992 bytes Database mounted. SQL> alter database archivelog; Database altered. SQL> alter database open; Database altered. SQL> archive log list; Database log mode Archive Mode Automatic archival Enabled Archive destination USE_DB_RECOVERY_FILE_DEST Oldest online log sequence 40 Next log sequence to archive 42 Current log sequence 42 SQL> show parameter log_archive_start NAME TYPE VALUE ------------------------------------ ----------- --------- log_archive_start boolean FALSE SQL>
That's all it requires to configure databsae in ARCHIVELOG Mode.
A question is why is log_archive_start FALSE setting. I think it should be TRUE.
Thank youSQL> Alter system archive log start; System altered. SQL> show parameter log_archive_start NAME TYPE VALUE ------------------------------------ ----------- --------- log_archive_start boolean FALSE SQL>
SAZYou don't need this setting. This setting was amortized to the oracle 10g database.
Concerning
Asif Kabir -
I am puzzled as to how I can configure firefox on night mode.
Hello, you can set a dark theme or automatic night mode when you use the reder mode in firefox for android...
-
The Switch configuration and Wi - fi router in the same network
Hi team,
I have here is the configuration currently as below in the image. To describe the same internet cable is connected to a Cisco switch, which is connected to the PC in LAN (wired). A switch output is connected to the entrance of the wireless router Netgear Nighthawk AC 1900 Smart model of WiFi router # R6900. Wireless devices (laptop) are connected by the router.
Each device has internet access. However, I am unable to run software LAN or unable to share any file of devices connected to the switch to the connected wireless devices. I can't ping any device the device wireless wired.
Can anyone suggest what are the settings that I should do or what are the steps I should follow that will make wireless and wired devices in the same network.
PS Plus early I tried the internet connection to the wireless router and then out of the router to pass, which has solved this problem. But slowing down my internet speed in wired devices. So, is it possible to have all devices in the network even with the current configuration?
Thanks in advance.
Best,
Hardik
I made wi - fi router reset hardware and configured in Access Point mode, that solved my problem.
-
How to set the differential input for personal iotech Daq/3000 mode
Hi all
I currently use personal iotech daq/3000 for the acquisition of data from the accelerometer.
I got readings of the analog input, while there seems to be no configuration for the differential mode.
What I have is:
selection of material - personaldaq / 3000:direct
Double click on, then:
Channel installation, there should be a selection of differential mode, I guess. But this is not.
Thank you very much
Alan
Have you reviewed the C:\Program Files\DASYLab 10.0\manuals\IOtech_DAQ_notes. PDF? Or the help of equipment?
The section of material assistance, using the analog inputs with DASYLab, includes pictures to show how to do this.
Open hardware driver.
Click the line Analog Input Channels, and then right-click to open the properties. This will display a dialog box that allows you to set the properties.
-
Parameters of Configuration of No (gain) of SCXI-1313 able and Automation Explorer
Hello
QUESTION:
Help, please. What should I do for my system to be able to define the 1125/1313 to re-read a +/-50v range?
DETAILS OF THE PROBLEM:
I have a SCXI-1125 module with a 1313 mitigation module which is be digitized by a PXI-6251.
I create my daqmx inside my program tasks. I want to put the max/min range for signals entering the 1125/1313 to +/-50v. However, I get an error of daqmx saying that the mini/maxi is limited to +/-10v.
Furthermore, I see no to the MAX so that the attenutaion of the 1313 or the gain of the 1125. MAX actually displays a message saying that there isn't any configuration required for the 1313.
Installation program:
LabVIEW 8.6
MAX 4.6.2f1
DAQmx 9.0.2
Windows 7 Pro - 32-bit
Best regards
Chris
Dear Chris,
You may find it useful to review the following Knowledge Base so that you can find more information on what I will explain:
http://digital.NI.com/public.nsf/allkb/B138E2AA836B5354862570380073EA60?OpenDocument
The SCXI-1313 is an attenuator module which serves to reduce your levels of input voltage so that they are in the range of input for your DAQ card voltage. When you use DAQmx in LabVIEW, you don't need to worry about setting the +/-50v rank because it will be scaling automatically. Simply choose any given voltage range is valid for your specific DAQ card (+/-10 v) in this case.
It is for this reason that when you go to MAX to try to configure the attenuation, you get a message telling you that you need not do this from the descaling is done automatically.
-
Configuration of the analog output of the controller PCI-7358
Hello world
I work with the PCI-7358 during a period of time and now I need to configure the output of the controller for a specific purpose. All I have to do is turn on and turn off the output to an analog 5V DC voltage level. I use a UMI-7774 as a breakthrough. I plugged the IO of 5-8 to the UMI axis MOVEMENT and I hope to get the tension off-axis 1 of the UMI CONTROL block. I use DAC.vi to load to turn on and off this PIN on UMI. When I tried the voltage level was 1.5VDC and it fluctuates so I tried to read the voltage on the PIN and she was 3.2Vac. It was said in this DAC.vi of charge help offset values or front torque limits does not affect the level of tension. I can't understand what is to limit the output voltage level. (I tried the 32000 and-32000 for entry this .vi)
If anyone can help urgently, I will be grateful...
Gencer Genç
Hi Roman,
in MAX, you must configure the axis as the stepper motors. You don't have to worry about the type of comment. You can leave this set to "encode". You can configure the engines loop Mode step by step in the tab settings of the Stepper to open loop. But in fact your needs, no matter, if you configure open-loop or closed-loop axis. Any mode stepper will be unmap the CAD of the axis.
In LabVIEW, just use ' configure axis resources "and map of the main output of your axis of stepper output or 'None '. This will also unmap the CAD of the axis. The secondary output must also be mapped to 'None '.
I hope this helps,
Jochen
-
Limits of vs in CSR or DIFF mode
Hello
I have the following question.
Some cards like 6009 Multifunction DAQ support several beaches for the configuration of the analog inputs differential as ±20V, ±10V, ±4V, ±2.5V, ±2V, ±1.25V, ±1V, while the CSR mode is supported only ±10V. However, the property of the device node lists all available tracks. When you configure the analog channel there is an option to choose the limits of signal and based on the limits of the DAQ driver automatically selects the range.
My problem is how to detect, according to the mode I select (DIFF vs CSR), what ranges are available to allow the user to select the voltage range without deceive the user to think that greater precision is selected, but the Council is to use only ±10V regardless of what limits are selected.
For example, if the device is configured to use HAVE mode DIFF by selecting signal ±1V limits will lead to measure in the range ±1V (greater precision), but if the device is configured to use CSR mode selection ±1V limits will mean nothing, because the driver will always use ±10V range because only this range is available.
Thank you
Ted
Hello
Thanks for the reply. The solution offers works if the info for 600 x series or if there is a list of cards DAQ coded into the software. However, I played a bit and found a more elegant and DAQ independent solution. Here is the diagram.
Below is the example of VI. The output array will duplicate areas of beaches which are used instead of unavailable lines, but then the removal of duplicates is trivial.
Ted
-
Using the scan Mode 9411 cRIO-9074
Hello
I use an entrance Module differential differential NI9411 under cRIO-9074 with scan Mode, but I noticed that some problems are present.
My application needs two encoder and we choose two incremental encoders with 1024pulses/rev. I have configured the NI9411 quadrature Mode, so I can read the position and speed of the encoder. Each shaft turn at different speeds.
One of them can turn 4.6 rad/s as a maximum speed, while the other hit it up to 402 rad/s. Then, the configuration of the module input filter is set to 1microsed, the time base speed 32768 microseconds and the disabled index mode. These values make for a correct reading? The cRIO scanning speed is set to 1ms.
On the other hand, watching the tutorials or (http://zone.ni.com/devzone/eda/tut/p/id/7109), that the degree of rotation depends on the encoding type, what type of encoding is used in Scan Mode? X 4?
Using System Manager OR distributed, one of the encoders to read impulses sometimes sporadic (up to 2 digits) Although the encoder is stopped. However, the other bed is always 0. It seems that the encoder is broken, isn´t it?
Thanks in advance for your comments
Hi Juancar,
I think that the values are suitable. The issue of reading 0 is explained in this KB:
http://digital.NI.com/public.nsf/allkb/C9088DFDF803CD8B862575F3007C40FD?OpenDocument
In addition, according to this document:
http://zone.NI.com/DevZone/CDA/tut/p/ID/7338
decoding type must be set to X 4.
I hope this helps! Suerte con ello.
Jesus
Maybe you are looking for
-
Unable to sign in iTouch with password security
why I can't SIGN IN on MY ITOUCH NOW? I USE TO BE ABLE TO GET ON THE NET TO THE HOME OR A PLACE OF FREE LIKE STARBUCKS WIFI. I TRIED TO CHECK MY LAPTOP TO SEE WHAT TO DO BECAUSE IT WORKED WELL AT THE BEGINNING
-
Internet Toolkit for LabVIEW 2012 64-bit
I have an application which is currently written in LabVIEW 2009. It requires the Internet. I try to open it in 2012 of LabVIEW (64-bit) (using Windows 7 64-bit). LabVIEW 2012 does not find the box at Internet tools since he has been deprecated in La
-
Hi, during the opening session on my computer, I got a little split screen, separation is 1/4 to the top of the screen and the screen ends 3/4 through my computer screen. It is not connected to a screen divided through tile, pls don't tell me to undo
-
CardScan Executive 700 c Scanner USB compatible with windows 7 64 bit?
CardScan Executive 700 c USB Scanner drivers available for Windows 7 64-bit?
-
IK heb een homecinemasysteem. Via een accespoint heb ik goede our price puts het internet. Via Nero mediahome4 was het expensive check-in een thuisgroep. IK krjg het niet meer voor een setting tot stand location you between pc en homecinemasysteem br