Configuration of the analog output of the controller PCI-7358

Similar Questions

• Black screen - try to activate the controller PCI of communication Simple: the drivers for this device are not installed. (Code 28)

  Original title: Safe Mode

  Can run my computer only in Safe Mode, whenever I try to boot into normal mode I get a screen with lines on the subject. Cannot download even the peak "white screen" now.

  Any help will be greatly appreciated. Thank you.

  New: I get his message when trying to activate the controller PCI of communication Simple:

  "Windows has enabled this device, however, this device still does not work correctly."

  Then:

  The drivers for this device are not installed. (Code 28)

  To reinstall the drivers for this device, click on reinstall.

  Then:

  "Windows cannot find the driver for your device".

  Get you the drivers accessing a site Web on your computer or the manufacturer of the graphics card > Search a drivers and download article > search your computer or your graphics card model number > your operating system > drivers for it: either video / graphic / Chipset (according to the label)

  See you soon.

• Model of card mother T7500 and configuration of the controller RAID LSI 1068e

  Hi, I just bought a T7500 workstation I would get around mid-December. Because of current prices for HARD drive storage, I decided to go with the 500 GB basic disk up to HEALING of Thailand. Thus, I am limited to basic integrated RAID controller. Because I am not familiar with the RAID configuration, etc. I wanted to read more before I dive in. The starting point would definitely find what was right for the Precision T7500 motherboard. Surprise! I can't find information anywhere. Even Dell people (3 different sales and support representatives) have not managed to tell me it's the Intel 5520 chipset (it looks that they believe that it is the motherboard model...). Well, I'm stuck. I would appreciate if someone could provide me with the model of motherboard and Special Edition, all information on the capabilities of the controller integrated RAID (LSI 1068e) would help me determine what drives should I plan to buy. In addition, one thing that is not clear to me what I inferred from the configuration on the website Wizard is the issue around disks > 2 TB. Of after I read it, I was not able to determine whether the problem was related to the simple readers > 2 TB or if it was related to the management of a storage space > 2 TB (which could be composed of several readers less than 2 TB). What I have in mind (remember that I do not have the machine right now) is to 4 X 1 TB drives in a RAID 0 + 1 (which I'm not sure that the integrated controller supports) configuration that will result in the storage of 2 GB mirrored. The operating system is Win 7 64 bit. Thanks in advance for any info that will help me to prepare my setup (buy hard drives, if I can find cheap ones) and find information on the configuration of the RAID. MrBricole

  I'm sure the T7500 uses an Intel Server Board (since this chipset is located on the Intel site under its motherboards, Dell is essentially correct, even if they didn't know why), but it doesn't matter in the context of your question, because the '' integrated '' RAID controller is not actually on the Board.  It's a card (called "integrated" only because it has a slot on this machine).  Because the functionality of the RAID controller is not on the Board of Directors, Board info will not help you.  Everything you need to know about your Council and the entire system, you can get the T7500 manual.  SAS 6/iR (LSI 1068e) RAID controller information can be found here:

  NOTE from the ADMIN: Broken link has been removed from this post by Dell >

  The SAS 6/iR will not support more than 2 TB of drives, or it will support more than 2 TB of virtual disks.

  It will also only supports RAID 0 OR RAID 1 OR both, but not together (not levels no RAID nested as RAID 10 or 0 + 1).

  So with four 1 TB drives, you can easily do two RAID 1 (called integrated mirror in the controller BIOS CTRL-C)... or you can do two 2-drive RAID 0 (Stripe called integrated in the controller BIOS CTRL-C)... or you can run mode non-RAID, with four individual discs in the operating system.  With this controller, those are your only options with four 1 TB drives.

  If you want / need more features RAID (nested RAID, 2 TB of the VFD above, on board levels, cache, etc.), you must upgrade to the PERC 6 / i.

  Do not buy office records class... Make sure you get enterprise-class drives.  If you decide at some point to go with PERC, not only enterprise class disks will be fundamentally necessary, but certified records would be strongly recommended for stability and performance.

• Properties of the controller PCI Simple communications in windows 8.1

  Update my PC in windows on HP Pavilion 500 - 307 x 8.1

  (1) missing PCI Simple communication controller

  Hardware ID

  PCI\VEN_8086 & DEV_8C3A & SUBSYS_2AF7103C & REV_04

  PCI\VEN_8086 & DEV_8C3A & SUBSYS_2AF7103C

  PCI\VEN_8086 & DEV_8C3A & CC_078000

  PCI\VEN_8086 & DEV_8C3A & CC_0780

  (2) missing BCM43142A0

  Hardware ID

  USB\VID_0A5C & PID_216C & REV_0112

  USB\VID_0A5C & PID_216C

  You are the very welcome.

  See if the driver for the IMEI of your laptop works...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-123966-1&cc=us&DLC=en&LC=en&OS=4158&product=6521374&sw_lang=

  I see the ID of the hardware for your device in the driver installation information file.

  [Intel.ntamd64.6.1]
  ; DisplayName Section DeviceId
  % TEE_DeviceDesc % = TEE_DDI_x64, PCI VEN_8086 & DEV_1E3A
  % TEE_DeviceDesc % = TEE_DDI_x64, PCI VEN_8086 & DEV_1CBA
  % TEE_DeviceDesc % = TEE_DDI_x64, PCI VEN_8086 & DEV_1C3A
  % TEE_DeviceDesc % = TEE_DDI_x64, PCI VEN_8086 & DEV_1DBA
  % TEE_DeviceDesc % = TEE_DDI_x64, PCI VEN_8086 & DEV_1D3A
  % TEE_DeviceDesc % = TEE_DDI_x64, PCI VEN_8086 & DEV_8C3A
  % TEE_DeviceDesc % = TEE_DDI_x64, PCI VEN_8086 & DEV_9C3A

• Lose the controller PCI simple communication (pavilion dm4-1265dx) driver

  Dear all,

  My laptop lost the PCI simple communications controller driver.

  I need to get the driver for my hp pavilion dm4-1265dx.

  Here are the hardware ID.

  PCI\VEN_8086 & DEV_3B64 & SUBSYS_146A103C & REV_06

  PCI\VEN_8086 & DEV_3B64 & SUBSYS_146A103C

  PCI\VEN_8086 & DEV_3B64 & CC_078000

  PCI\VEN_8086 & DEV_3B64 & CC_0780

  I tried to find the driver on the Net, but I can't find the driver.

  I sincerely hope that everyone can provide the URL or the installation of the pilot program.

  Thanks for everyone's help.

  Hello

  Download and install the Intel MEI Driver at the following link.

  http://ftp.HP.com/pub/SoftPaq/sp50501-51000/sp50858.exe

  Kind regards

  DP - K

• acquire the voltage output of a channel of analog output current

  I'm controlling a HV configuration rather sensitive analog output voltages. Is there an easy way to read the voltage level which is currently awarded by an analog output?

  Hello

  If you set your subVIs different voltages, you can be sure that the voltage you set in these screws are similar to tensions, you have to your output PIN. For example, you could write the value you give to the output in a variable and read this variable in you main VI.

  Kind regards

  Peter

• What are the PCI ANALOG OUTPUT PORTS Terminal 6024E block CB-68LP

  Dear all

  I want to get the analog output on the physical output signal. In my LabVIEW diagram, I develop the DAQ assistant and configure ao0 as analog output. The tension I want hovel is analog - 5v to + 5 volts. Terminal block, what will be the output port analog physical that I measure this voltage.

  Waiting for ypur response.

  Kind regards

  Irfan

  In MAX, you can simply right-click on the device and select 'device pinouts. The DAQ Assistant will also show pinout.

• Unable to apply the model of WLAN to the controller through WCS

  Unable to apply the model of WLAN to the controller through WCS

  1 update your config all of your controllers of WCS. Go to configure---> controllers--> select all controllers.
  2. in the drop-down "Select", choose "refresh the configuration from the controller and select 'Go'."
  3. choose Delete therefore WCS will take the last setting of the WLC and select 'go '.
  4. remove the WCS WLC.
  5. Add WLC to WCS.
  6 try to set up the model again.

  Also, you can upgrade to 6.0.170 as there are to many model feature bugs that have been fixed in this version.

  http://www.Cisco.com/en/us/docs/wireless/WCS/release/notes/WCS_RN6_0_170.html#wp44440

  -nael

• variable phase shift between two analog output signals

  Hey! I would drive two different piezo elements with an sine - / square signals and have a phase shifted output signals. After some trail and error, I was able to get a second analog output on my card PCI-6221 (using LabView 8.2) also allowed me to have different amplitudes for both signals. However, I could not output signal having a frequency different and most importantly to my request to have one of the signals variably shifted phase.

  Thanks for the very useful suggestion. I have attached the file .vi installation I've run so far.

  Hello!

  A way to generate waveforms is using the analog waveform Toolbox. I created an example VI that is attached and that shows you a way to use the base generating function VI. I saved for LabVIEW 8.2.

  I hope this helps!

• Strange problem with analog output PCI 6251 and BNC-2110

  I'm controlling current source of third parties using the connectors of analog output on my card PCI 6251 and BNC-2110.

  The current source needs an input signal of 0.1V. I tested it using a battery, the potentiometer and the voltmeter, and by manually adjusting the voltage of power current works - current output with control voltage scales according to the specifications and is relatively stable.

  The data acquisition card works too - when I connect a voltmeter to the AO0 AO1, the measured voltage corresponds to the target with great precision value.

  But when I connect the current source of third AO0 AO1 data acquisition card, the measured output voltage drops and fluctuates. This applies to both channels of the AO.

  I wonder what is the problem here. I suspect it could be a matter of the grounding - the current analog control of the source is an entry with two floating terminals differential. I tried to return the switches FS/GS on the BNC-2110, but that makes no difference.

  Anyone knows similar behavior? Does anyone have any suggestions?

  
  

• How can I change the configuration for the output channels analog on a PXI-6704?

  I can't seem to understand how to access the configuration of the channels to the outputs analog (channel 33 and 35) for PXI-6704.

  This piece of test equipment is out of tolerance and must be calibrated.

  I have followed the procedure of calibration http://www.ni.com/pdf/manuals/374081b.pdf, but am getting hung up on step 8, where it is said to repeat steps 4-7 when changing the _cal_ao_current_offset. I can't figure out how to open this channel because it is not listed as a physical channel for step 5.

  I'm using Labview 7.1

  Thank you

  Hello! What you need to do is to add 'Internal channels' to your list of channels, so you can choose the _cal_ao_current_offset or _cal_ao_voltage_offset.  This is done through the drop-down list channel right click and select "I/o name of screening...". ».  There will be a check box that says 'Internal channels' and will provide you with all available internal channels to enter your vi Create Channel.  I have attached some photos illustrating how to do. See you soon!

• To input analog shutdown when the analog output is completed and synchronization

  Hello

  I'm trying to get my LabVIEW program to send analog output to a computer and read acceleration using the cDAQ-9184. Chassis output that I use is the NI 9263 and the chassis of entry is the NI 9234. I generate a signal of white noise using LabVIEW Express signal generator.

  The first problem I have is the synchronization. I had an old VI that has begun to measure the acceleration just about a second after the entry has been given to the machine. I used the LabVIEW tutorial on how to sync the analog input and output, only to discover that it does not work with two different hunts. Then I found another tutorial that shows how to synchronize different frames between them.

  The second problem is the cessation of the LabVIEW program. What I want to do is to generate the signal and then simultaneously send and read the input and output analog, respectively. It is because I don't want a phase difference or any shorter signal for a direct comparison. But as soon as the signal is sent to the machine, I want the entry to stop analog playback and then then the LabVIEW program must stop. I want to be able to choose any length of signal to be generated and stop as soon as the entire duration of the signal has been sent to the machine.

  I tried 'DAQmx stop', "DAQmx Timer" and 'DAQmx's task made?' and none of them have worked for me. It is also my first time on a forum posting, so I hope I gave enough information. I enclose my VI as well. The VI shows I read an entry for the analog input voltage, but I am only using this to try to get to the work programme.

  I'd appreciate any help I could get.

  Thanks in advance

  Peter

  Hi Peter,.

  I have some recommendations for you that I think you will get closer to your solution. First of all, I assumed you meant that you had 1 chassis (cDAQ-9184) who had two modules in it (NOR-9263 and NOR-9234). My next steps are based on this assumption, so if it's wrong, please let me know.

  For your first question about the synchronization, the code you provided is very close to what you need. You need to do, however, implement architecture master/slave for startup tasks DAQmx functions. To do this, you can add another frame to the flat sequence structure and put the master start task (input voltage) after the start slave (output voltage) task.

  To manage your second question and that the program ends at the point where you, the first step is to get rid of all the logic that you use with the local variable of length of time. Rather than use this logic, just wire the node "task performed?" of "is task performed?" operate to stop the loop. This will cause your loop to stop as soon as the signal is sent to the machine.

  I have some other recommendations for you that will increase the performance of your program:

  (1) rather than writing on file inside the last loop, you can use the DAQmx Configure Logging (PDM) .vi. You will place this VI between DAQmx Timing.vi and DAQmx Start Task.vi to the task of the analog input voltage.

  (2) after the last while loop, you want to stop the task and analog outputs as well with another DAQmx stop Task.vi.

  (3) rather than using a local variable for the entrance of displacement and wiring it in the DAQmx Write.vi, you can wire directly from the output waveform of the wave to build function node.

  That should help you get started in the synchronization of these tasks.

  -Alex C.

  Technical sales engineer

  National Instruments

• How to determine the number of highlight ' to write ' for DAQmx generate analog output?

  On the configuration of the stage for DAQmx generate analog output, there is a field "value to write.  I can't find any explanation for what it is, how it determines the value to enter, nor what he writes.  I am trying to go through the tutorials and it cling.

  Someone would give an explanation?

  Hello

  To write value specifies the value to write in the channels, lines or ports selected in string parameters. In other words, this value will be the value of your DC output (for example if you enter 5, your output will be 5V). To get information on different fields in SignalExpress, access help"context-sensitive help. A pane will appear in your work environment that displays the coordinates of the field when you place your pointer over them.

  For new users of SignalExpress:

  Generation of DC signals with NI DAQmx devices: step in the DAQmx build, select 1 sample (on request) in the generation Mode dropdown. You can select a programmatic input to generate, or you can remove the check mark from the check box use programmatic input and specify a value for generating in the field of value to write . NOR-DAQmx help also provides additional information about the data generation.

  Best regards

  M Ali

  Technical sales engineer

  National Instruments

• Problem of generation of the analog output on PCI-7342

  I use for the control of servo motor with encoder Axis 1 of my PCI-7342 feedback

  and trying to out of the velocity of the encoder on the analog output of the axis-2 which is currently not used.

  For testing purposes, I pulled out a constant 16383 (half of 32767) to the analog output

  through load DAC.flx permanently, but there is no voltage on the map of the motion.

  I read

  http://digital.NI.com/public.nsf/WebSearch/102BE3EEED8A8B0DC1256EDA0059EC47?OpenDocument

  http://forums.NI.com/T5/motion-control-and-motor-drives/analog-output-voltage-from-UMI-7764/m-p/5219...

  http://forums.NI.com/T5/motion-control-and-motor-drives/configuring-the-analog-output-of-PCI-7358-mo...

  and configure my 2 axis to be a stepper motor. I also tried to disable axis - 2. None of them works for me.

  Also, I tried to read the value of CAD using reading DAC.flx right after that load DAC.flx is called.

  Correctly, the value was shown on the screen. (See the attached figure)

  I'm really bad now. Please, please, please help!

  Any possible solution is fully appreciated!

  Ron Liou

  
  

• NEITHER 6052e: can I re - route the analog output of DAQ for PFI?

  Hello

  Does anyone know if it is possible to route analog output to one of the PFI (e.g. PFI0)? I use NEITHER 6052e and I would do the following: 1) output a signal to DAQ0; 2) then a few hundred milliseconds a signal of DAQ1; and then 3) read out a simple analog pulse on any output connector external to trigger an external device.

  Thank you very much for your help!

  Hello sometimes.

  Could you please provide more information about your hardware configuration:

  What devices are DAQ0 and DAQ1?

  Are you using a PXI and PCI 6052?

  When you say AO reroute to PFI do you mean you're trying to wire AO into a PFI line for release purposes or are you trying to exit and the analog signal of a PFI line?