Confusion of access VPN site to Site list

Hi all

I was wondering if someone could help me explain access lists when the configuration site to site VPN tunnels. Basically, I used this guide to create nearly a GNS3 lab to make me understand IPSec etc tunnels.

http://commonerrors.blogspot.co.UK/2011/09/site-to-site-VPN-CLI-configuration-on.html

It is this config works and my confusion is on the ACL they use. There is no mention of the internal subnet 10.1.1.1 on US router subnet but Pakistan a range 172.16.x.x internal in ACLs (but no it's external ISP IPs)

Why it works? This configuration is incorrect?

With these tunnels VPN site-to-site, what the source/destination IP address ranges should be in them?

Any help or information would be great.

Thank you

Paul

With the crypto ACL, the source must be the local LAN subnet and the destination should be the Remote LAN subnet. Crypto ACL defines interesting traffic that you want to encrypt remote and local peer.

The external interface of the router (generally the one with the public IP address assigned by ISP) will be used to encrypt the crypto ACL and is defined by the command "set by the peers.

Hope that helps.

Tags: Cisco Security

Similar Questions

remote VPN and vpn site to site vpn remote users unable to access the local network

As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.

Hello

Looking at the configuration, there is an access list this nat exemption: -.

192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

But it is not applied in the States of nat.

Send the following command to the nat exemption to apply: -.

NAT (inside) 0 access-list sheep

Kind regards

Dinesh Moudgil

P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

A Site to remote access VPN behind the same public IP address

Got a problem quite stupid. We have a VPN from Site to Site configured for a new data center, which will be responsible for general traffic management. In addition, some users need to use use a VPN client to access certain areas. The firewall at the Office only has a public IP address, so the two will come to the Site to Site VPN for remote access from the same source.

This seems a problem with legacy Cisco VPN clients because encryption card matches the entry VPN site-to-site, even if they use VPN clients. A good/simple solution to solve this problem?

Some newspapers (198.18.85.23) is the address public IP for the office and the tom.jones is the user. 192.168.1.0/24 is the pool of the VPN client.

January 7, 2014 19:12:52 ASA5515: % 713130-5-ASA: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, transaction mode attribute unhandled received: 5

January 7, 2014 19:12:52 ASA5515: % 737003-5-ASA: PISG: DHCP not configured, no viable servers found for tunnel-group "Corp-VPN.

January 7, 2014 19:12:52 ASA5515: % 713119-5-ASA: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, PHASE 1 COMPLETED

January 7, 2014 19:12:52 ASA5515: % ASA-3-713061: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, IPSec tunnel rejecting: no entry for crypto for proxy card remote proxy 192.168.1.4/255.255.255.255/0/0 local 0.0.0.0/0.0.0.0/0/0 on the interface outside

January 7, 2014 19:12:52 ASA5515: % ASA-3-713902: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, error QM WSF (P2 struct & 0x00007fff28dab560, mess id 0x37575f3c).

January 7, 2014 19:12:52 ASA5515: % ASA-3-713902: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, peer table correlator Removing failed, no match!

January 7, 2014 19:12:52 ASA5515: % 713259-5-ASA: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, Session is be demolished. Reason: political crypto card not found

January 7, 2014 19:12:52 ASA5515: % ASA-4-113019: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, disconnected Session. Session type: IKEv1, duration: 0 h: 00 m: 02s, xmt bytes: 0, RRs bytes: 0, right: not found card crypto policy

January 7, 2014 19:12:53 ASA5515: % 713904-5-ASA: IP = 198.18.85.23, encrypted packet received with any HIS correspondent, drop

Hello

Don't know if this will work, but you can try the following configuration (with the rest of the VPN configuration)

list-access CLIENT VPN ip enable any 192.168.1.0 255.255.255.0

card crypto OUTSIDE_map 4 is the VPN CLIENT address

card crypto OUTSIDE_map 4 set peer 198.18.85.23

card crypto OUTSIDE_map 4 set ikev1 transform-set ESP-AES-128-SHA ESP-3DES-SHA

The idea would be to have the ACL matches the VPN full Tunnel that the Client attempts to establish. (destination "any" from the point of view of the customer, the ASAs view source)

I tested briefly on my own SAA by connecting from an IP address to which the ASA offers free VPN in L2L. But as I don't have the operational L2L VPN, I can't really verify the VPN L2L at the moment. Thus, certain risks may be involved if you can afford it.

-Jouni

AnyConnect VPN full tunnel could not access the site to site VPN

I have a set of AnyConnect VPN upward with no split tunneling (U-turning/crossed traffic), running 8.2.5 code.

It works fine, but I want to allow customers to AnyConnect VPN site to site, which I was unable to access.

I checked the IP addresses of network anyconnect are part of the tunnel on both sides.

My logic tells me that I must not turn back traffic from the network anyconnect for the site to site VPN, but I don't know how to do this.

Any help would be appreciated.

Here are the relevant parts of my config:

(Domestic network is 192.168.0.0/24,

the AnyConnect network is 192.168.10.0/24,

site to site VPN network is 192.168.2.0/24)

--------------------------------------------------------------------------------------

permit same-security-traffic inter-interface
permit same-security-traffic intra-interface

the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.0.0 255.255.255.0
object-network 192.168.10.0 255.255.255.0
inside_nat0_outbound list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.10.0 255.255.255.0

outside_1_cryptomap list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0

mask 192.168.10.2 - 192.168.10.254 255.255.255.0 IP local pool AnyConnectPool
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 1 192.168.10.0 255.255.255.0
access-outside group access component software snap-in interface outside
Route outside 0.0.0.0 0.0.0.0 (the gateway IP) 1
WebVPN
allow outside
AnyConnect essentials
SVC disk0:/anyconnect-win-3.1.05152-k9.pkg 1 image
SVC profiles AnyConnectProfile disk0: / anyconnect_client.xml
enable SVC
tunnel-group-list activate
internal AnyConnectGrpPolicy group strategy
attributes of Group Policy AnyConnectGrpPolicy
WINS server no
value of 192.168.0.33 DNS server 192.168.2.33
VPN-session-timeout no
Protocol-tunnel-VPN l2tp ipsec svc
Split-tunnel-policy tunnelall
the address value AnyConnectPool pools
type tunnel-group AnyConnectGroup remote access
attributes global-tunnel-group AnyConnectGroup
address pool AnyConnectPool
authentication-server-group SERVER1_AD
Group Policy - by default-AnyConnectGrpPolicy
tunnel-group AnyConnectGroup webvpn-attributes
the aaa authentication certificate
activation of the Group _AnyConnect alias

Your dial-up VPN traffic as originating apears on the external interface, so I think you need to exonerate NAT pool PN traffic directed to the site to site VPN. Something like this:
```
 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 nat (outside) 0 access-list outside_nat0 nat (outside) 1 192.168.10.0 255.255.255.0 access-list outside_nat0 extended permit ip any 192.168.10.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.10.0 255.255.255.0
```

local host to access the vpn site to site with nat static configured

I have two 881 routers with vpn site to site between them. I have a static nat on the router for a Web server that is accessible from the internet. I can't access the Web server through the vpn. All other traffic is fine its VPN. I think that there is a problem with the NAT. Here are the relevant configuration lines.

IP nat inside source overload map route SDM_RMAP_1 interface FastEthernet4
IP nat inside source static 192.168.150.2 bonnefin map route SDM_RMAP_1

allowed SDM_RMAP_1 1 route map
corresponds to the IP 100

access-list 100 deny ip 192.168.150.0 0.0.0.255 192.168.123.0 0.0.0.255
access-list 100 permit ip 192.168.150.0 0.0.0.255 any

You should be able to access the web server with its IP private (192.168.150.2) through the VPN connection.

If you just add the VPN and the road map, try to clear the existing translation and see if you can access it via its private of the Remote LAN VPN ip address.

2 VPN SITE to SITE with ACCESS REMOTE VPN

Hello

I have a 870 router c and I would like to put 2 different VPN SITE to SITE and access remote VPN (VPN CLIENTS) so is it possible to put 3 VPN in the router even if yes can u give me the steps or the sample configuration

Concerning

Thus, on the routers will be:

Cisco 2611:

LAN: 10.10.10.0/24

access-list 100 permit ip 10.10.10.0 0.0.0.255 10.10.20.0 0.0.0.255

access-list 100 permit ip 14.1.1.0 0.0.0.255 10.10.20.0 0.0.0.255--> VPNPOOL

!

10 ipsec-isakmp crypto map clientmap

defined by peer 172.18.124.199

match address 100

!

IP local pool ippool 14.1.1.1 14.1.1.254

!

access-list 120 allow ip 10.10.10.0 0.0.0.255 14.1.1.0 0.0.0.255

access-list 120 allow ip 10.10.20.0 0.0.0.255 14.1.1.0 0.0.0.255 --> NETWORK REMOTE

!

crypto ISAKMP client configuration group ra-customer

pool ippool

ACL 120

!

Please note that the configuration is incomplete, I added that relevant changes, you should bring to the allow clients of RA through the LAN-to-LAN tunnel, of course, the LAN-to-LAN settings should match to the other side of the tunnel that is mirror of ACL, NAT and so on.

HTH,

Portu.

problem with users to access remote vpn site to site vpn network

I did the Setup: asa 5510 configured remote access vpn. My vpn users receive asa 5510 range 192.168.50.0/24 addresses and users access my local lan 192.168.0.0/24. the second side of the local lan 192.168.0.0/24 on asa 5505, I did a vpn site-to-site with network 192.168.5.0/24.on that both sides of a site are asa 5505. inside the interface asa 5510 Elise 192.168.0.10 and inside the interface asa 5505 have address 192.168.0.17.third asa 5505 networked 192.168.5.0/24 address 192.168.5.1. I want my remote access vpn users can access resources on network 192.168.5.0/24. I create the static route on inside the asa 5510 static route 192.168.5.0 interface 255.255.255.0 192.168.0.17 and a static route on inside the asa 5505 static route 192.168.50.0 interface 255.255.255.0 192.168.0.10, but it's not working. What do I do?

execution of the configuration of my asa 5510 is

Result of the command: "show run"

: Saved
:
ASA Version 8.4(2)
!
hostname asa5510
domain-name dri.local
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
nameif outside
security-level 0
ip address x.x.x.178 255.255.255.248
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.0.10 255.255.255.0
!
interface Ethernet0/2
description Mreza za virtualne masine- mail server, wsus....
nameif DMZ
security-level 50
ip address 172.16.20.1 255.255.255.0
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
!
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns server-group DefaultDNS
domain-name dri.local
object network VPN-POOL
subnet 192.168.50.0 255.255.255.0
description VPN Client pool
object network LAN-NETWORK
subnet 192.168.0.0 255.255.255.0
description LAN Network
object network NETWORK_OBJ_192.168.0.0_24
subnet 192.168.0.0 255.255.255.0
object network 192.168.0.10
host 192.168.0.10
object service ssl
service tcp destination eq 465
object service tls
service tcp destination eq 995
object network mail_server
host 172.16.20.201
object service StartTLS
service tcp destination eq 587
object service admin_port
service tcp destination eq 444
object service ODMR
service tcp destination eq 366
object service SSL-IMAP
service tcp destination eq 993
object network remote
host 172.16.20.200
object network test
host 192.168.0.22
object network mail
host 172.16.20.200
object network DMZ
host 172.16.20.200
object network Inside_DMZ
host 192.168.0.20
object service rdp
service tcp destination eq 3389
object network DRI_PS99
host 192.168.0.54
object service microsoft_dc
service tcp destination eq 445
object service https448
service tcp destination eq 448
object network mail_server_internal
host 172.16.20.201
object service Acronis_remote
service tcp destination eq 9876
object service Acronis_25001
service tcp destination eq 25001
object service HTTP3000
service tcp destination eq 3000
object network VPNPOOL
subnet 192.168.50.0 255.255.255.0
object-group network PAT-SOURCE-NETWORKS
description Source networks for PAT
network-object 192.168.0.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object object admin_port
service-object object ssl
service-object object tls
service-object object https448
object-group service DM_INLINE_SERVICE_2
service-object object admin_port
service-object object https448
service-object object ssl
service-object object tls
service-object tcp destination eq pop3
service-object tcp destination eq smtp
object-group service DM_INLINE_SERVICE_3
service-object object admin_port
service-object object https448
service-object object ssl
service-object tcp destination eq smtp
service-object object tls
service-object object Acronis_remote
service-object tcp destination eq www
service-object object Acronis_25001
service-object object microsoft_dc
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object tcp
object-group service DM_INLINE_SERVICE_4
service-object object Acronis_25001
service-object object Acronis_remote
service-object object microsoft_dc
service-object tcp destination eq www
service-object tcp
service-object ip
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 any object mail_server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any object mail
access-list Split_Tunnel_List extended permit ip 192.168.0.0 255.255.255.0 any
access-list outside_cryptomap extended permit ip 192.168.0.0 255.255.255.0 192.168.5.0 255.255.255.0
access-list DMZ extended permit object-group DM_INLINE_SERVICE_4 172.16.20.0 255.255.255.0 any
access-list DMZ extended permit object-group DM_INLINE_SERVICE_3 host 172.16.20.201 any
access-list DMZ extended permit object-group DM_INLINE_PROTOCOL_1 172.16.20.0 255.255.255.0 any inactive
access-list DMZ extended deny tcp any any eq smtp
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu DMZ 1500
mtu management 1500
ip local pool vpnadrese 192.168.50.1-192.168.50.100 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static LAN-NETWORK LAN-NETWORK destination static VPN-POOL VPN-POOL
!
object network mail_server
nat (DMZ,outside) static x.x.x.179
object network mail
nat (DMZ,outside) static x.x.x.180
access-group outside_access_in in interface outside
access-group DMZ in interface DMZ
route outside 0.0.0.0 0.0.0.0 178.254.133.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
action terminate
dynamic-access-policy-record dripolisa
aaa-server DRI protocol ldap
aaa-server DRI (inside) host 192.168.0.20
ldap-base-dn DC=dri,DC=local
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *****
ldap-login-dn CN=dragan urukalo,OU=novisad,OU=sektor2,OU=REVIZIJA,DC=dri,DC=local
server-type microsoft
user-identity default-domain LOCAL
aaa authentication enable console LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication telnet console LOCAL
aaa authorization command LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 192.168.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
virtual telnet 192.168.1.12
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 195.222.96.223
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.0.14-192.168.0.45 inside
!
dhcpd address 172.16.20.2-172.16.20.150 DMZ
dhcpd dns x.x.x.177 interface DMZ
dhcpd auto_config outside interface DMZ
dhcpd option 6 ip x.x.x.177 interface DMZ
dhcpd enable DMZ
!
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
!
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy GroupPolicy_x.x.x.223 internal
group-policy GroupPolicy_x.x.x.223 attributes
vpn-tunnel-protocol ikev1 ikev2
group-policy drivpn internal
group-policy drivpn attributes
dns-server value 192.168.0.20 192.168.0.254
vpn-simultaneous-logins 10
vpn-idle-timeout 30
vpn-tunnel-protocol ikev1 l2tp-ipsec
split-tunnel-network-list value Split_Tunnel_List
default-domain value dri.local
username driadmin password AojCAMO/soZo8W.W encrypted privilege 15
tunnel-group drivpn type remote-access
tunnel-group drivpn general-attributes
address-pool vpnadrese
authentication-server-group DRI
default-group-policy drivpn
tunnel-group drivpn ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group x.x.x.223 type ipsec-l2l
tunnel-group x.x.x.223 general-attributes
default-group-policy GroupPolicy_x.x.x.223
tunnel-group x.x.x.223 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect tftp
inspect ip-options
inspect netbios
inspect icmp
inspect http
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:69c651e94663fc570b67e0c4c0dcbae1
: end

running config asa 5505

Result of the command: "show run"

: Saved
:
ASA Version 8.2(1)
!
hostname ciscoasa
enable password csq7sfr0bQJqMGET encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.5.0 PALATA
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.17 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address 10.13.74.33 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
object-group service DM_INLINE_SERVICE_1
service-object ip
service-object tcp
service-object icmp echo
service-object icmp echo-reply
service-object tcp eq domain
service-object tcp eq ldap
service-object tcp eq smtp
object-group service DM_INLINE_SERVICE_2
service-object ip
service-object tcp eq domain
service-object tcp eq www
service-object tcp eq https
service-object tcp eq smtp
object-group service Sharepoint8080 tcp
port-object eq 8080
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any any
access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_2 192.168.0.0 255.255.255.0 any
access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
access-list outside_2_cryptomap extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
pager lines 24
logging enable
logging asdm informational
logging mail errors
logging from-address
logging recipient-address level debugging
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 192.168.0.0 255.255.255.0
static (inside,outside) 10.13.74.35 192.168.0.22 netmask 255.255.255.255
static (inside,outside) 10.13.74.34 192.168.0.20 netmask 255.255.255.255 dns
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 10.13.74.1 1
route inside 0.0.0.0 0.0.0.0 192.168.0.17 tunneled
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication telnet console LOCAL
http server enable
http 10.13.74.0 255.255.255.0 outside
http 192.168.0.0 255.255.255.0 inside
http 10.15.100.0 255.255.255.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
virtual telnet 192.168.0.53
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_2_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 10.15.100.15
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!

threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username driadmin password AojCAMO/soZo8W.W encrypted privilege 15
tunnel-group 10.15.100.15 type ipsec-l2l
tunnel-group 10.15.100.15 ipsec-attributes
pre-shared-key *
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
!
service-policy global_policy global
smtp-server 173.194.79.109
prompt hostname context
Cryptochecksum:4767b6764cb597f0a7b8b138587d4192
: end

Thank you

Hello

I have previously edited the my initial response was in fact not necessary since you were actually using full Tunnel

EDIT: Actually just noticed the the VPN client isnt using Split Tunnel. Its Full Tunnel at the moment since it doesnt have the "split-tunnel-policy tunnelspecified"

So you don't really have any of those.

Please mark the question answers and/or assess response

Ask more if necessary

-Jouni

VPN site to site access via a VPN client

Hi all

From our headquarters, we use a vpn site-to-site to connect to another site and it works great.

We have just configured the VPN client on our headquarters, remote VPN user can access the LAN in the seat.

We need the remote user can also access the LAN on the other site, but it does not work.

The site to site VPN and VPN client are configured on the same device, using even outside the interface.

Vpn client address pool is already included in the address that is allowed to go through the site to site VPN.

We would like to know if it is possible to access the site to site VPN, connecting to the VPN client and when the architecture is as above?

in the case where we use different devices and different internet connection for client VPN and site to site VPN, we can access the other site by the remote user VPN LAN?

Kind regards

Since you already have 10.13.0.0/16 in your site to site crypto ACL, which already includes the pool vpn so you need not configure it specifically.

You are missing the following command:

permit same-security-traffic intra-interface

ACL split tunnel should be standard ACL as follows:

access list ACL-CL-VPN allow 10.13.0.0 255.255.0.0

access list ACL-CL-VPN allow 10.14.0.0 255.255.248.0

ASA5505 VPN Site to site and limiting access - URGENT

I'll admit knowledge limited to the front, so forgive me if I look like a fool. The company that I work began recently to hosting our application for some of our customers. to do this, we are renting rack space, connections and equipment in a data center. We must send data to our request for an application in the center of data of our customers. They have an ASA 5505.

Our data center will support VPN site-to-site and nothing else. Our client find it unacceptable, citing security and the inability to restrict access to only the small number of servers, our application needs to access. I have to be able to talk intelligently and with the facts (and, preferably, examples of configuration on hand) with their staff of the IOC and network in the next day or so.

The ASA 5505 can be configured for a VPM from site to site with our data center which limits our application server to access a limited set of IP addresses within their network? If so, this is quite easily possible? Anyone done this?

Thank you

Leighton Wingerd

Leighton,

Sounds complicated problem - but are simple actuall. Remember that a VPN ensures the transmission from site A to site B on a precarious environment - internet. For example, you can DEFINE the traffic that goes through the VPN, you also DEFINE the traffic that will launch the VPN tunnel in the first place. With these statements said - using your supposed information you would create valuable traffic as the exact traffic you want to allow through the vpn;

access-list permits datacentre_2_client tcp host 1.2.3.4 host 192.168.1.2 eq 1521

And you will use the same ACL to set which can cross traffic. However, I know for a fact that an ODBC Oracle connection uses more than one TCP port!

The confidentiality of data is something else - that your customer needs to define requirements. An SSL connection is fine and dandy - you will just be to encrypt the traffic twice!

Cannot access remote network by VPN Site to Site ASA

Hello everyone

First of all I must say that I have configured the VPN site-to site a million times before. Stuck with it. First of all I can't ping outside the interface of my ASA remote. Secondly, VPN is in place, but no connectivity between local networks

ASA local:
hostname gyd - asa
domain bct.az
activate the encrypted password of XeY1QWHKPK75Y48j
XeY1QWHKPK75Y48j encrypted passwd
names of
DNS-guard
!
interface GigabitEthernet0/0
Shutdown
nameif vpnswc
security-level 0
IP 10.254.17.41 255.255.255.248
!
interface GigabitEthernet0/1
Vpn-turan-Baku description
nameif outside Baku
security-level 0
IP 10.254.17.9 255.255.255.248
!
interface GigabitEthernet0/2
Vpn-ganja description
nameif outside-Ganja
security-level 0
IP 10.254.17.17 255.255.255.248
!
interface GigabitEthernet0/2.30
Description remote access
VLAN 30
nameif remote access
security-level 0
IP 85.*. *. * 255.255.255.0
!
interface GigabitEthernet0/3
Description BCT_Inside
nameif inside-Bct
security-level 100
IP 10.40.50.65 255.255.255.252
!
interface Management0/0
nameif management
security-level 100
IP 192.168.251.1 255.255.255.0
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
DNS server-group DefaultDNS
name-server 192.168.1.3
domain bct.az
permit same-security-traffic intra-interface
object-group network obj - 192.168.121.0
object-group network obj - 10.40.60.0
object-group network obj - 10.40.50.0
object-group network obj - 192.168.0.0
object-group network obj - 172.26.0.0
object-group network obj - 10.254.17.0
object-group network obj - 192.168.122.0
object-group service obj-tcp-eq-22
object-group network obj - 10.254.17.18
object-group network obj - 10.254.17.10
object-group network obj - 10.254.17.26
access-list 110 scope ip allow a whole
NAT list extended access permit tcp any host 10.254.17.10 eq ssh
NAT list extended access permit tcp any host 10.254.17.26 eq ssh
access-list extended ip allowed any one sheep
icmp_inside list extended access permit icmp any one
icmp_inside of access allowed any ip an extended list
access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
RDP list extended access permit tcp any host 192.168.45.3 eq 3389
rdp extended permitted any one ip access list
sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
NAT-vpn-internet access-list extended ip 192.168.121.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 172.26.0.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 192.168.122.0 allow 255.255.255.0 any
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.60.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.50.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 192.168.0.0 255.255.0.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 172.26.0.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.254.17.0 255.255.255.0
GHC-ganja-internet access-list extended ip 192.168.45.0 allow 255.255.255.0 any
Standard access list Split_Tunnel_List allow 192.168.16.0 255.255.255.0
azans 192.168.69.0 ip extended access-list allow 255.255.255.0 any
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.121.0 255.255.255.0
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.80.0 255.255.255.0
pager lines 24
Enable logging
emblem of logging
recording of debug console
recording of debug trap
asdm of logging of information
Interior-Bct 192.168.1.27 host connection
flow-export destination inside-Bct 192.168.1.27 9996
vpnswc MTU 1500
outside Baku MTU 1500
outside-Ganja MTU 1500
MTU 1500 remote access
Interior-Bct MTU 1500
management of MTU 1500
IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
IP local pool ssl 192.168.121.130 - 192.168.121.200 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any outside Baku
ICMP allow access remotely
ICMP allow any interior-Bct
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
global (outside-Baku) 1 interface
global (outside-Ganja) interface 2
3 overall (RAS) interface
azans access-list NAT 3 (outside-Ganja)
NAT (remote access) 0 access-list sheep-vpn-city
NAT 3 list nat-vpn-internet access (remote access)
NAT (inside-Bct) 0-list of access inside_nat0_outbound
NAT (inside-Bct) 2-nat-ganja access list
NAT (inside-Bct) 1 access list nat
Access-group rdp on interface outside-Ganja
!
Router eigrp 2008
No Auto-resume
neighbor 10.254.17.10 interface outside Baku
neighbor 10.40.50.66 Interior-Bct interface
Network 10.40.50.64 255.255.255.252
Network 10.250.25.0 255.255.255.0
Network 10.254.17.8 255.255.255.248
Network 10.254.17.16 255.255.255.248
redistribute static
!
Access remote 0.0.0.0 0.0.0.0 85.*. *. * 1
Outside-Baku route 10.0.11.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.33.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.150.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.170.0 255.255.255.0 10.254.17.10 1
Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
Route outside Baku 10.254.17.32 255.255.255.248 10.254.17.10 1
Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.27.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.66.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
Outside-Baku route 192.168.80.0 255.255.255.0 10.254.17.11 1
Access remote 192.168.121.0 255.255.255.0 85.132.43.1 1
Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
Route inside-Bct 192.168.254.0 255.255.255.0 10.40.50.66 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede GANYMEDE +.
AAA-server GANYMEDE (Interior-Bct) 192.168.1.8
key *.
AAA-server GANYMEDE (Interior-Bct) 192.168.22.46
key *.
RADIUS protocol AAA-server TACACS1
AAA-server TACACS1 (Interior-Bct) host 192.168.1.8
key *.
AAA-server TACACS1 (Interior-Bct) host 192.168.22.46
key *.
authentication AAA ssh console LOCAL GANYMEDE
Console to enable AAA authentication RADIUS LOCAL
Console Telnet AAA authentication RADIUS LOCAL
AAA accounting ssh console GANYMEDE
Console Telnet accounting AAA GANYMEDE
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 Interior-Bct
http 192.168.139.0 255.255.255.0 Interior-Bct
http 192.168.0.0 255.255.255.0 Interior-Bct
Survey community SNMP-server host inside-Bct 192.168.1.27
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
Crypto ipsec transform-set esp-3des esp-sha-hmac vpnclienttrans
Crypto ipsec transform-set vpnclienttrans transport mode
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.10
card crypto mymap 10 transform-set RIGHT
correspondence address card crypto mymap 20 110
card crypto mymap 20 peers set 10.254.17.11
mymap 20 transform-set myset2 crypto card
card crypto mymap interface outside Baku
correspondence address card crypto ganja 10 110
10 ganja crypto map peer set 10.254.17.18
card crypto ganja 10 transform-set RIGHT
card crypto interface outside-Ganja ganja
correspondence address card crypto vpntest 20 110
peer set card crypto vpntest 20 10.250.25.1
newset vpntest 20 transform-set card crypto
card crypto vpntest interface vpnswc
vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
card crypto interface for remote access vpnclientmap
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = gyd - asa .az .bct
sslvpnkeypair key pair
Configure CRL
map of crypto DefaultCertificateMap 10 ca certificate

crypto isakmp identity address
ISAKMP crypto enable vpnswc
ISAKMP crypto enable outside-Baku
ISAKMP crypto enable outside-Ganja
crypto ISAKMP enable remote access
ISAKMP crypto enable Interior-Bct
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 30
No vpn-addr-assign aaa
Telnet timeout 5
SSH 192.168.0.0 255.255.255.0 Interior-Bct
SSH timeout 35
Console timeout 0
priority queue outside Baku
queue-limit 2046
TX-ring-limit 254
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.168.1.3
SSL encryption, 3des-sha1 rc4 - md5 aes128-sha1 sha1-aes256
SSL-trust point ASDM_TrustPoint0 to vpnlb-ip remote access
SSL-trust ASDM_TrustPoint0 remote access point
WebVPN
turn on remote access
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal group ssl policy
attributes of group ssl policy
banner welcome to SW value
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
group-lock value SSL
WebVPN
value of the SPS URL-list
internal vpn group policy
attributes of vpn group policy
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the PFS
BCT.AZ value by default-field
ssl VPN-group-strategy
WebVPN
value of the SPS URL-list
IPSec-attributes tunnel-group DefaultL2LGroup
ISAKMP retry threshold 20 keepalive 5
attributes global-tunnel-group DefaultRAGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
IPSec-attributes tunnel-group DefaultWEBVPNGroup
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.10 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.10
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type SSL tunnel-group remote access
attributes global-group-tunnel SSL
ssl address pool
Authentication (remote access) LOCAL servers group
Group Policy - by default-ssl
certificate-use-set-name username
Group-tunnel SSL webvpn-attributes
enable SSL group-alias
Group-url https://85. *. *. * / activate
tunnel-group 10.254.17.18 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.18
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.11 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.11
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type tunnel-group DefaultSWITGroup remote access
attributes global-tunnel-group DefaultSWITGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultSWITGroup
pre-shared key *.
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect the netbios
Review the ip options
class flow_export_cl
flow-export-type of event all the destination 192.168.1.27
class class by default
flow-export-type of event all the destination 192.168.1.27
Policy-map Voicepolicy
class voice
priority
The class data
police release 80000000
!
global service-policy global_policy
service-policy interface outside Baku Voicepolicy
context of prompt hostname

Cryptochecksum:4f35f975ba7a0c11f7f46dfd541d266f
: end
GYD - asa #.

ASA remote:
ASA Version 8.2 (3)
!
ciscoasa hostname
activate the encrypted password of XeY1QWHKPK75Y48j
2KFQnbNIdI.2KYOU encrypted passwd
names of
DNS-guard
!
interface Ethernet0/0
nameif inside
security-level 100
IP 192.168.80.14 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 10.254.17.11 255.255.255.248
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
nameif management
security-level 100
no ip address
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
access-list 110 scope ip allow a whole
192.168.80.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.0.0 255.255.0.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
management of MTU 1500
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ICMP allow any inside
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside) 0 access-list sheep
Route outside 0.0.0.0 0.0.0.0 10.254.17.9 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.80.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.9
mymap 10 transform-set myset2 crypto card
mymap outside crypto map interface
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN

tunnel-group 10.254.17.9 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.9
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname

Cryptochecksum:1c1ac60e2fb84f65269d15d53f27c21b
: end
ciscoasa # $

Still, I can't ping ASA remote outside from outside of the Local interface. And there is no connectivity between the 192.168.80.0 distance and local don't say 192.168.1.0. I have run out of ideas

Would appreciate any help. Thank you in advance...

If the tunnel is up (phase 1), but no traffic passing the best test is the following:

Add order management-access to the Interior , and then try to PING the intellectual property inside ASA counterpart.

inside x.x.x.x ping --> x.x.x.x is the IP of the ASA peer inside

The test above shows if the traffic passes through the tunnel (check encrypted/decrypted packets of sh cry ips its).

Test on both directions.

Please post the results.

Federico.

VPN access to site-toSite to servers of HO with remote site with overlapping network...

Hi all

I have an obligation to create a tunnel vpn site-to-site on ASA 5510 from a remote location to my HO, I have already other site to site tunnels are on the rise and running on the ASA. This is what my remote site got the network address that is part of a subnet used in HO(192.168.10.0/24). My requirement is only my need to access remote site couple of my servers in HO, who is in the subnet 192.168.200.0/24.

Veuileez help how can I achieve this... your advice at the beginning is very appreciated...

Thanks in advance
Mikael

Hi Salem,

I think the installer at your end is a bit like this:

You want the remote location to access the subnet 192.168.200.0/24 behind the ASA HQ servers. In this case, you can NAT traffic from the remote site to a different subnet when you go to 192.168.200.0/24.

i.e. the 192.168.10.0/24 subnet resemble 192.168.51.0/24 when he goes to 192.168.200.0

This can be done by using political based natting:

permit access-list policy-nat ip 192.168.10.0 255.255.255.0 192.168.200.0 255.255.255.0

public static 192.168.51.0 (inside, outside) access-l policy-nat

In the encryption of the remote side access list, you will have:

cryptoacl ip 192.168.51.0 access list allow 255.255.255.0 192.168.200.0 255.255.255.0 (this is because the remote side will see 192.168.51.0/24 and not the 192.168.10.0/24)

Similarly on the end of HQ the accesslist crypto will be

XXXXX 192.168.200.0 ip access list allow 255.255.255.0 192.168.51.0 255.255.255.0

Please try this and let me know if it helps.

Thank you

Vishnu Sharma

Access Manager will not see this website need a supervisor password. This Page has been blocked by your approved Sites list.

kb956196

Access Manager will not see this site, supervisor password needs. This page has been blocked by your approved sites list

We have forgotten the password. is there a way to reset the password or to disable it without the password?

Hello

Download and run the http://www.nirsoft.net/utils/conadvpass.html program (if you are able to access the site)

If not, perform this task:

"If you have forgotten the password of Access Manager, you can remove it by accessing this folder in Regedit (don't forget to back up your registry first):

HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\

CurrentVersion\Policies\Ratings

Select the key called icon in the right pane and press on delete. Close Regedit.

Now, you can start Internet Explorer and goto tools, Internet Options... Select the content tab and click on disable. When asked a password, do not write, just click OK. This will disable access Manager, since nothing is more a password. You can enable it again as soon as invent you a more memorable password"

VPN site to Site with client access VPN

I have a pix 500 series configured with access to the VPN client. When I set up a site to site vpn to a remote location, access to the customer no longer works. If I remove the vpn site to site, the vpn client works again. I tried the MDP and the CLI. Someone could look at my config and let me know what I'm missing. See the two configs attached.

Thank you

Lost in VPN

Ah, I missed that. You can change the States of card crypto for virtual private networks to be on the same card encryption like this...

mymap 20 ipsec-isakmp crypto map

card crypto mymap 20 match address ipsecvpn

card crypto mymap 20 peers set xxx.xxx.100.180

transform-set set mymap 20 sha - crypto card game

map mymap 65535-isakmp ipsec crypto dynamic outside_dyn_map

client card crypto mymap RADIUS authentication

mymap outside crypto map interface

or

outside_map 20 ipsec-isakmp crypto map

card crypto outside_map 20 match address ipsecvpn

card crypto outside_map 20 peers set xxx.xxx.100.180

transform-set set sha - game card crypto outside_map 20

map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

outside_map the RADIUS client authentication card crypto

outside_map interface card crypto outside

ASA 5510 vpn remote access - must now be added vpn site-to-site.

We currently have a configuration of remote access vpn and all this hard work.

I need to configure a vpn lan lan 2 now.

Can someone point me to the documentation on that? I used the command line to add a site to site and wrong on it and disconnected me when I applied the crypto map to the external interface. Do I need another card encryption or should I use my existing?

Shannon,

Please see the below URL for more configuration information. Even if that configuration is dynamic to static IPSEC, you can use the concept to build the Tunnel L2L with static IP.

http://www.Cisco.com/en/us/partner/products/ps6120/products_configuration_example09186a00805733df.shtml

Let me know if it helps.

Kind regards

Arul

* Please note all useful messages *.

Help with 1921 SRI Easy VPN remote w / Easy VPN Site-to-Site access

I have two 1921 ISR routers configured with easy site to site VPN. I configured VPN each ISR ACL so that all networks on each site can communicate with the private networks of the other site. I have a 1921 SRI also configured as an easy VPN server.

Problem: when a remote user connects to the easy VPN server, the user can only access private networks on the site of the VPN server. I added the IP network that is used for remote users (i.e. the Easy VPN Server IP pool) to each VPN ACL 1921, but the remote user still cannot access other sites private network via the VPN site to another and vice versa.

Problem: I also have a problem with the easy VPN server, do not place a static host route in its routing table when he established a remote connection to the remote user and provides the remote user with an IP address of the VPN server's IP pool. The VPN server does not perform this task the first time the user connects. If the user disconnects and reconnects the router VPN Server does not have the static host route in its routing table for the new IP address given on the later connection.

Any help is appreciated.

THX,

Greg

Hello Greg,.

The ASAs require the "same-security-traffic intra-interface permits" to allow through traffic but routers allow traversed by default (is there no need for equivalent command).

Therefore, VPN clients can access A LAN but can't access the Remote LAN B on the Site to Site.

You have added the pool of the VPN client to the ACL for the interesting site to Site traffic.

You must also add the Remote LAN B to the ACL of tunneling split for VPN clients (assuming you are using split tunneling).

In other words, the VPN router configuration has for customers VPN should allow remote control B LAN in the traffic that is allowed for the VPN clients.

You can check the above and do the following test:

1. try to connect to the remote VPN the B. LAN client

2. check the "sh cry ips his" for the connection of the VPN client and check if there is a surveillance society being built between the pool and Remote LAN B.

Federico.

Confusion of access VPN site to Site list

Similar Questions

Maybe you are looking for