Connect to Force10 MXL N4032 using cables QSFP + DA 40 G

Similar Questions

• Cannot connect the Blackberry curve 8330 mobile using cable and Bluetooth

  Original title: I tried to connect my mobile curve8330blkberry with a cable and the pc does not recognizes it, tried via bluetooth and the same. Everyone pls.helptried to connect

  tried o my blkberry curve 8330 with a cable and Bluetooth

  Hello

  ·         What operating system do you use?

  ·         Are you able to connect other devices to your computer without any problem?

  ·         Did you try to connect the device to the other computer and check if it works?

  Method 1:

  Try running the fixit from the link give below and check if this can help:

  Hardware devices not detected or does not
  http://support.Microsoft.com/GP/hardware_device_problems

  Method 2:

  I suggest you to contact the Blackberry Support for better assistance and check if it helps.

  http://us.BlackBerry.com/support/devices/blackberrycurve8300.jsp

• My laptop does not work on a wireless connection that I have to use the yellow Ethernet cable to use internet.

  My laptop does not work on a wireless connection that I have to use the yellow Ethernet cable to use internet.

  I followed the instructions on my laptop on how to connect to broadband and I even called the company from whom get connection but they could n, t help me. I need help! I want to use my wireless laptop and how do I do it?

  Hi Hn_668,

  See the articles below and check if it helps.

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

  In Windows network connection issues

  http://support.Microsoft.com/kb/313242

  To set up automatic wireless network configuration

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/wlan_client_configure.mspx?mfr=true

  5 steps: how to set up your network wireless home

  http://www.Microsoft.com/athome/organization/wirelesssetup.aspx

• I added a router and a connection high speed using windows vistawhen pc is connected to the router her there is no internet connection. When the pc connected to the Internet by modem cable is available

  I added a router and a connection high speed using windows vistawhen pc is connected to the router her there is no internet connection. When the pc connected to the Internet by modem cable is available

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  It will be useful.

• No access to the personal files of Windows 7 to the disc format hard using a new computer that connects with a USB 2.0 cable to SATA/IDE in Windows 8

  I have a HDD that has been removed from a computer that does not work and I try to access my files staff on it. When the drive is connected, it appears as two items in Explorer: 'system Reserved (f)' and 'disk space (g) '. This drive has been connected to my new computer using a USB 2.0 to SATA/IDE cable.

  I can see all the program files and public folders in the path (g), but not one of my staff, including music, documents, photos, etc.. The path (f) does not seem to access anything whatsoever.

  My new computer using Windows 8, the hard drive, I'm trying to access Windows 7.

  This seems to be a security problem, that I have no idea on how to fix. I tried enabling 'total control' in the tab 'security' in the properties, what has not changed the situation.

  All solutions/advice would be much appreciated.

  Thank you.

  Hi David,

  1. What is the brand and model of the hard drive?

  2. do you get an error message/code?

  3 have you tried to connect the hard drive to a different USB port?

  4 have you tried the search for files by using the search function?

  This problem may be caused by the virus or files might be hidden.

  Method 1:

  Scan the hard drive for viruses:

  Reference:

  Microsoft safety scanner

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Method 2:

  Follow these steps and check:

  a. press the Windows key + X

  b. Select Control Panel and folder options.

  c. in the view tab, select Show hidden files, folders and disks and click on apply and then OK.

  d. check if you can see the files on the hard drive.

  I hope this helps. If the problem persists, you can write to us and we will be happy to help you further.

• Force10 MXL and blades - mapping of Interfaces

  Hello

  I know it's a recurring topic but I am facing a strange problem in the last M1000e chassis that I was sent.

  According to: mapping is very clear. For example, the first interface of the first plank must be connected via the Midplane to te0/1 (first in the IOM1 interface), but when I set up the battery of the A2 Force10 MXL (just a pile between A1 and A2) became the master so I changed the priorities to ensure that A1 is the master. Once this is done, I realized that the first interface of the first blade was linked to the Te1/1, the first IOM2 interface. Is it possible to change this? I have several chassis and I want to set all the same way...

  Thank you!

  What servers are used? Just to be clear, while MXL in A2 was the master, the LOM 1 port connected to 0/1 and the LOM 2 port connected to 1/1? Then when you changed a switch to A1, now port 1 shows that 1/1 LOM and LOM 2 port connected to 0/1?

  The ports are all physically defined by the M1000e chassis.
  Have you tried:
  -unstacking switches
  -Can ensure that ports appear correctly so that not stacked.
  -Set the priority and then put.
  -Check the enumeration.

• OfficeJet Pro 8500 a Premium: loss of connectivity wireless when I plug the cable on Officejet Pro 8500 a

  Successfully, I can connect an ethernet cable to the ethernet on the back of my printer port and print to the printer via the cable network.  I can unplug the ethernet cable and configure the printer features wireless to the printer and print successfully on the network wireless to the printer.  However, when I try to use wired and wireless at the same time (both running), it won't work.  If I try to turn on wireless with an ethernet cable connected to the printer, I get a warning message on the home screen, indicating that wireless printer can not be configured or turned on when an ethernet cable is plugged.

  Is this a limitation of the hardware printer or I have the printer configured incorrectly?

  I tried to reset the printer default network settings and reconfiguration of network but still have the same problem as described above.  On a HP Officejet 8600 A separate premium, however, I remember that the two cables and wireless can work at the same time.

  Thank you very much for your help!

  Hello

  This is a limitation of the printer, either a cable or a wireless network connection may work, you cannot use two connection options at the same time.

  Kind regards

  Shlomi

• Settings need to connect a second desktop computer using a NetGear wireless adapter.

  Original title: wireless settings

  I need the settings to connect a second desktop computer using a NetGear wireless adapter.

  The Belkin router work a lot using my Tablet and streaming movies but I can't understand

  the settings on the second PC.

  Any help will be appreciated.

  Thank you.

  "Settings", you need are the SSID (network name) and the encryption key (password).

  Unless you have configured the router to 'hide' the SSID (generally a bad idea), you will see in the list of available wireless networks.  Then, the only thing you need is the encryption key.

  If you do not write your encryption key, you can find it by logging into your router configuration utility.

  If you have a computer running Windows can now connect to the router, open a command prompt window (start > run > cmd > OK) and type "ipconfig" (without the quotes) and press ENTER.  Take note of the 'Default gateway' address.  It is the IP address of the router.

  The default IP for Belkin routers is 192.168.2.1.

  On a computer that is already connected to the router, open a browser (Internet Explorer or Firefox) and enter the IP address of the router (the gateway by default, you noted above or 192.168.2.1).  If you do not have a computer that is connected to the wireless router, you will need to temporarily connect a computer to the router by an Ethernet cable.

  Connect to the router configuration utility.  If prompted for a password and you don't remember, you need to reset the router to its factory default.  Return ticket for additional instructions.

  Once logged in, click on "Security" under "wireless" in the menu.  At this point, you should see a page that shows your password.  Write it down and exit the router configuration utility without making any changes.

  For more help, post back with the model of your Belkin router and also mention if you have any Windows computer that can connect to the router (and if yes, what version of Windows they use).

• My photosmart c309g-m is connected to the router by ethernet cable. Can I add?

  My photosmart c309g-m is connected to the router by ethernet cable.  Can I still add to e-print?

  Hello

  Is a printer ready ePrint? You can use the home router to access the internet? If Yes and Yes, then you should be able to do.

  Kind regards.

• Then a Force10 MXL blade handle no FCoE traffic?

  Hello.  I inherit a M1000e with few blades of the Force10 MXL switch installed.  The chassis has no other 10GBASE-T switches.  Since I have no plans on using FCoE, a Force10 MXL can be used for standard Ethernet (non-FCoE) traffic?  Or do I have to buy another switch?

  Thank you.

  Absolutely, to see the second page of the data sheet. It contains additional information about the available modules, how internal traffic is manipulated and external.

  http://Dell.to/1Q5fUo9

  The manuals are a great place to start. There is that a starter guide to help set up initial, and then a CLI and user guide to help configure additional features.

  http://Dell.to/1IIq8r2

  Let us know if you have any other questions.

• DeskJet 6940 connected via ethernet to the airport cable, do not print

  Hello

  I used to run my HP Deskjet 6940 printer using a USB connection. I recently installed an Apple Airport Extreme so I can print wireless. If necessary, the printer is connected to the airport by using an ethernet cable and turned on the light green network. On the advice of a HP rep by phone, I uninstalled all old HP software and reinstalled HP software downloaded from the HP website.

  When I try to add the printer to my 'system preferences', it opens a panel that contains the following options:

  Protocol: Automatically selects "line printer daemon - LPD.

  Address: Empty but allows me to type in the IP address assigned

  Print using: no idea.

  More than two things: when I open the HP Device Manager and select "set up a network, information network configuration printer seems in good condition but the Manager does not allow me to 'apply'.  Not sure if this is important but no the printer utilities appear in my folder utlities since the new software download. Thank you.

  Looks like you are using a Mac.

  First of all, the driver for the Deskjet 6940 is built into Mac OS.  You really didn't need to download additional www.hp.com (sorry for the bad advice) stuff.

  Next, we'll check that the printer is on the network.  In Safari, select bookmarks, display all bookmarks.  Select Hello in the left pane, and then check the Deskjet 6940 appears on the list of devices on your network.

  Then, follow these instructions to reset the print Mac subsystem: http://support.apple.com/kb/HT1341

  Now add the printer to the Print & Fax under System Preferences applet by pressing the [+] button.  The Deskjet 6940 should be among the kind Hello from printers.  Select it and press Add.

  I think that should do it.

• HP EliteBook 8440p does not connect to the external monitor using VGA! Help!

  As you can read by the title, this computer does not connect to an external monitor using VGA.

  It will be not just to record all monitors in the control panel.

  Can I change the resolution, change the color, etc.. But it will pick up any display.

  -This computer has a HDMI port.

  -The Windows key and pressing P make the ring of little blue loading appear for a microsecond before nothing appears.

  -VGA cable is brand new, double male, directly connected to my Panasonic Viera 32 ''.

  -In the properties of this computer is giving an error code that this computer has no drivers. (Code 28)

  After a repair, he says "device Base system has not a pilot.

  Can someone direct me to the corresponding pages for drivers or instructions? Any help would be appreciated.

  There is probably a combination of keys specific to your model that enables / disables the VGA port on and outside.  Look in high ranking a key with a marking saucy that some how is supposed to look like a monitor.

• Unable to connect laptop to TV via HDMI cable

  Original title: unable to connect

  I recently put HP G-62 - b51SE.I tried to connect to my HDMI TV using the HDMI cable but nothing works. Is there a way I can connect. What settings should I do in order to make the display appear on television. I have windows 7 ultimate.

  Hi Lovemicrosoft,

  1. first you need a video cable to make the physical connection. For a better image quality, you must connect to the computer to the TV using standard VGA ports or via DVI to HDMI cable provided your TV supports these ports.

  2. open the "display settings" in your Vista computer and activate the output to the TV screen. You can reflect the content of your computer on the TV or extend the display as a double screen control.

  3. pick up your TV remote and switch to "External inputs" in the menu. You need to change the value by default "Video 1" to a different selection which may be "HDMI 1" or "video 2" depending on how you made the connection. "

  Important: Make sure you connect the cable to the TV before turning on the computer, because sometimes it may not recognize the external display.

  You may also change the resolution of your TV screen using the display settings in your panel of control remains the image may appear distorted.

  Link to view:

  What should I know before adding TV tuners to use with Windows Media Center?

  http://Windows.Microsoft.com/en-us/Windows7/what-should-I-know-before-adding-TV-tuners-to-use-with-Windows-Media-Center

• How can I connect to iTunes that it used to work now it isn't

  How can I connect to iTunes that it used to work now it isn't

  When happens when you connect the iPod to your computer running iTunes?  You say it does not appear in iTunes at all?

  Look at the screen of the iPod when you connect it to the USB port on the computer?  He said not 'connected' or 'do not disconnect' or give another indication of a data connection?  Or is it just to show battery charge symbol?  Or not it reacts at all to be connected?

  Your computer is equipped with a Mac or a Windows PC iTunes?  If Windows, which free?

• I have a problem connecting on ebay if you use firefox, I get a message saying that the page does not not despite having cleared my cache and cookies.

  I have a problem connecting on ebay when you use firefox, it has been fine for years, but since a few days, I get a message saying that the page does not when I try to log in. I tried to clear my cookies and cache, but it makes no difference. This does not occur in google chrome and I can log on fine there so what's the problem with firefox?

  Do you also have this problem if you temporarily switch to private browsing mode?

  • https://support.Mozilla.org/KB/private+browsing
  • Tools > Options > privacy, choose the setting Firefox will: use the custom settings for the story of
  • Select: [X] 'always use private browsing mode '.

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance/themes).

  • Makes no changes on the start safe mode window.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

  See also:

  • https://support.Mozilla.org/KB/fix-login-issues-on-websites-requrie-passwords