Connection of the PXI-4071 - can sound and LOs remain interconnected for the impedance of the cable 2, voltage DC/AC, frequency and waveform acquisition?

Similar Questions

• Linksys Router WRT160N - Wireless does not connect to the cable modem

  I installed the Linksys WRT160n router to replace an existing G router. When installed the new wireless router works, but the router does not receive a connection (IP address - look under status) of the cable modem (so no internet). When I reconnect the old router and then connect the new router, I get any internet connection through two routers (so the old dishes router the IP address that accepts the new router).

  I have configured the router N new for

  "Automatic configuration - DHCP", no need for connection, IP address dynamic, etc (as required by ISP - Timewarner)

  I tried to renewal and release IP address by the router N when it is connected directly to the main switch (the switch to connect to the cable modem). In so doing, shouldn't that assign a new IP address to the router?

  I am allowed 3 IPs from the cable company (because of the switch) and I use all three with three different internet IP cameras to each address for home security system.

  Any suggestions on why the router is not connecting to the internet? Do I need to reboot physically everything on the network, including the cable modem?

  If I understand your post, you said that your ISP gives you 3 Internet IP addresses and you have 3 cameras that use one of these Internet IP addresses.  If this is correct, then that leaves no IP Internet address for your WRT160N use - so that would explain why your WRT160N cannot get an Internet connection.

  If I misread your post, and you have an Internet IP address available for the WRT160N, you might have a problem with your modem and two WRT160N tries to use the same 192.168.1.x subnet.  To check this, follow these steps:

  (1) Please indicate addresses that use your cameras (IE before you take the test below).  If the addresses do not begin with 192.168, then erase the last half of each address.

  (2) Please indicate your ISP

  (3) Please indicate the make and exact model of your modem (not the WRT160N) number.

  (4) Please do the following test:

  Put your entire network.  Disconnect the switch (including cameras) to the modem.  Using an ethernet cable, connect your modem directly to your computer.  (Do not use the WRT160N for this test).  Turn on the modem and the computer.  Make sure you have an active Internet connection, then go ahead with what follows: (even if your Internet connection does not work, include this and move forward.)

  Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig/all" (with no quotes), and press the Enter key.   Copy all results in your next post.  To make the copy, highlight the results, and then use the keys copy (Ctrl-c) and paste (Ctrl-v) keys.  If your "IP address" does not begin with 192.168, then for security reasons, delete the latter half of your IP address.

• In MS Project - how can I loose change "remaining work" for my tasks to 0?

  In MS Project - how can I loose change "remaining work" for my tasks to 0?

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• HP 8600 Pro Premium: 8600 Pro Premium connected to the cable network shows as not connected on the list of devices

  My printer/Premium Pro 8600 is wire connected to my network and works very well (exception below) but shows as not connected on the list of devices on my desktop computer Win 10.  What gives?  Private network.

  I also can not connect to my laptop which is connected wireless to the network.

  Hello and welcome to the community of HP @Pickles2011,

  I understand that you are having problems with your HP Officejet Pro 8600 Premium connection. I'll be happy to help you.

  Here are some links to documents that provide solutions for troubleshooting connection problems. Try the steps and let me know the results.

  HP printers - Printer not found during setup of the network (Windows) driver

  Wireless printing Center - Troubleshooting

  If it helps, will testify of my answer by pressing the 'thumbs up' below, or click on the button "Accept as Solution" if I helped you reach a solution.

  I hope this helps and have a nice day.

• Intermittently, Time Capsule does not connect to the cable Modem

  Capsule time bought a few weeks ago.  Barely implemented.  TC does not recognize the cable modem.  These forums to get help.  Tracking the specific set of sequence with long delays between the steps and the modem and the TC.  It worked for about a month.  Now about once a day the TC works but not internet wireless or ethernet through the CT.  If I unplug the TC and let it restart and initialize internet connection returns.  During the internet cuts I have ethernet and Wi - Fi at transport CANADA, printers, and drives on the network as well as the time Capsule backup drive and your data.  If I ever lose ethernet and Wi - Fi to TB.  In addition, the modem works fine.  If I cut the TC and to the cable modem ethernet connection I have access to the internet.

  Thank you.  All were huge last time assistance.

  If it's always the same modem... a SB6141 of Arris... There have been a number of reports of trouble with this product with Apple routers. There is no mention that in your first post a month ago, because we wanted to see if a reset of the good modem would get things works well for you.  I had the same experience as with the same exact modem you have.

  The SB6141 is a good product, and the time Capsule is as well. But for some users, these two products do not work as well together. If you call people to support for modem, they show sure to like the question time Capsule. If you call Apple, they will have a different view on things. The bottom line when you go to a support group... because it of always the other guy that you are having problems.

  At this point, the only real solution would be to decide if you want to try another brand and model of modem and keep the time Capsule, or keep the modem and try another brand of router and then connect the Capsule to the router.

  In my case, I replaced the SB6141 (I tried 3 different SB6141s previously because the ISP admitted having difficulties with this modem and some routers) with a 5341J Zoom, and did not have a single falling Internet connection since I installed the Zoom for more than a year. If your Internet service provider indicates that the Zoom is a product that is compatible with their service, you might want to try this modem.

  But unfortunately, there is no assurance that the "solution" that has worked for me will be the solution that suits you. Such is the nature of the beast, when you work with products from two different suppliers.

• Dell Dimension 4600 with pack 1 XP does not connect to the cable modem

  Hello, I have a Dell Dimension 4600 older XP. The hard drive is dead and I replaced and then reloaded pack 1 with the intention of making all the revisions on the internet. The problem is that I cannot now connect to the internet via my broadband router directly connected to the computer. It seems that the wizard to connect only wants to use the dial upward and does not connect to the router. Just recompose. It seems to ignore the connection from the router to broadband and wants to use the dial upward only.

  Go to control panel of control/Internet options/connections, then set it - never establish a connection - then click on apply.

• HP8600 print in reverse order from OSX 10.9.5. Connected through the cable network.

  His impression back in front. I see how to resolve this problem in Windows 7, but there seems to be no option in HP utility on the mac; Paper handling has only "Tray Lock" and "Tray by default".

  5.23.4 HP utility

  Hi John, I hope you had a good weekend!

  I recommend you create a print preset.  I'm linking a document below on how to creat and modify the predefined settings:

  Creating and editing print settings predefined

  Please hold me!

• Connection of the cable to the HDTV. .

  Is it possible to view the multimedia content of my Z3 by connecting the port supported USB cable to the USB input on my HDTV?

• my laptop won, t connect to the internet more without the ethernet cable, help attatched

  As I, ve said it won, t connect unless the cable is connected.

  I had to change the password for internet security to allow my new Apple iPad access to the internet, 3 days after my laptop refuses to connect to the internet.

  I, made the change of the password in my laptop security settings, but after I pressed ok, apparently the password returns to that of origin and isn, t recognized. Can someone help, please

  Hello

  Thanks for posting your query in Microsoft Community and thank you for the opportunity to help you.

  From the description of the problem, it seems that you have difficulty to connect to the internet without Ethernet cable.

  To help you to propose measures to solve the problem, I would appreciate if you could answer the following questions:

  1. you receive an error message or error code?

  2 did you do changes on the computer before the show?

  I suggest to follow the steps in the article mentioned below and check if that helps.

  Why I can't online?

  http://Windows.Microsoft.com/en-us/Windows-Vista/why-cant-I-get-online

  You can also see the following article for more information on Internet connection problems:

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

   

  Hope this information helps. Answer please if you have any additional questions about the problem you are having and we will be happy to help you further.

• wireless connection with the unidentified network

  Hello

  I have recently moved house and who to connect my computer to the wireless network that we installed. He works to connect said however that the network is 'unidentified' and I can't connect to the internet. I tried to diagnose the problem, but nothing seems to work. There is nothing wrong with the router, because it works with all other computers in the House except our HP computers two and it works whenever I connect with the cable, but not wifi.

  I've had the laptop for about 5 years now.

  Computer: HP Pavilion DV6824eo PC entertainment network

  Operating system: Windows Vista 32-bit

  I would be very happy if someone could help me with this!

  Lovisa

  I managed to fix everything at the time, had to download the latest version of the WLAN ahteros driver.

  Thank you very much!

• Toshiba NB550-111 - no connection if the LAN cable is more than 2 metres

  Hello

  My newly purchased Toshiba NB550-111(Windows 7 Starter Service Pack 1) has problems with the LAN card.
  If the LAN cable is more than 2 meters, no relation to Allied Telesyn switch (no indicator led on the switch, 2 other desktop computers already connected). I tried not to connect in a different port (one used previously by one of desktop computers), no connection. I tried with 3 cables, still no results.

  Cables (cat5E, so important) have been tested OK before with a cable Tester, and I use both of them without any problem with another 2 desktop computers at home. I set another cable (5 m long, newly purchased) and tested for connectivity. It works very well with the other two offices, no results with the netbook. I tried with adapter it works, I disabled ' energy efficient ethernet "NIC, still no connection properties page. It only connects if the cable is less than 2 meters. I tried to connect the netbook directly to the DSL router, still no connection with a longer cable.

  The device is reported by windows as work very well, and the test Toshiba utility ends there is no problem. Windows I configured in the Control Panel, the Plan balanced for maximum performance in the power options, still no results.
  Any ideas, please?

  Now maybe stupid question but what is with WLAN? You don t want to use WLAN?

• Error starting: "check the cable connection.

  Original title: that check the connection of the cable during the start up to the average?

  When I boot my computer says check cable connection? my computer crashed and has messed with it when you start to get in the system until I restored the computer to its original state. help I don't want to go through this again

  Hello

  ·          What version of the operating system is running on your computer?

  ·          Where there are changes made to your computer before this problem?

  ·          Question took place even after the computer has been restored to its original state?

  ·          It's a laptop or a desktop computer?

  This happens usually when the physical connection to the computer is not intact. Make sure that the physical connections are correctly configured.

• Lose the wireless connection when the modem connects to the internet.

  Hello

  I've updated my laptop to windows 7 (new installation).  I have a cable modem which is connected by ethernet to a wireless modem/router which I have configured to be a wireless access point (dhcp is the cable modem).  The laptop can connect wireless access point when the cable modem is not connected to the internet (so the ip address of the access point is 192.168.100.50 & the laptop takes an automatic ip address within the range). The problem is when I connect the modem cable to the internet, & so the ip address of the access point is derived the cable modem, the laptop can't connect to the access point. When I renew the ip address of the wireless card, it says it is connected to the selected network but the ip address is not correct, nor do I have access to the internet.

  The laptop connects fine to pick up the new ip address when it is ethernet connected the access point when the cable modem is both on or off, so I can access the local access point configuration when the modem cable is off, & can access the internet when the cable modem is enabled. When it is connected with the cable modem access point wireless at sea, both my wireless & ethernet connection say that they are connected to the selected network, but as soon as I turn on the cable modem, wireless connection says it is connected to an unidentified network, but my ethernet connection is connected to the selected network.

  I tried the broadcasting/no broadcast of the SSID, different levels of security, modification of the power saving options on the card wireless without success. I don't think it's a problem with the real network that the wireless card can capture the network & settings when the cable modem is disabled.

  This Setup has worked well when I had win xp.  My mobile phone can capture the network without wire end also & is able to access the internet.  The driver for the wireless card is current as well as the firmware on the access point.

  Can you please help? Thank you very much

  Hi Jack

  You led me in the right direction with the MAC addresses on the cable modem.  It's a simple solution... turn off the cable modem so it would refresh the MAC addresses of connecting devices, & hey presto, I wireless & ethernet access internet on my laptop with wireless internet on my laptop.

  Thank you for your perseverance.

  See you soon

• Unable to connect to the computer using wifi

  A got a new Sony HX30V and tried to use the feature "send to the computer. He is able to connect to the wi - fi home and also able to detect the name of the computer to which it is supposed to transfer the photos to. However, during the process to actually connect to the computer, it throws a "network error" after trying for about 30 seconds. I have Windows 8 running on my system. Any ideas how to solve this?

  After spending hours and hours with exactly the same problem, I found the solution. I tried with 2 computers with different OS, 2 different networks, and I read a lot of posts...

  The problem behind it is that you could not transfer images using WIFI while your computer is also connected via WIFI.  Then:

  (1) connect your computer using the connection of the cable to the access point.

  (2) connect the camera via USB to your computer and make sure that the PlayMemories software detects the camera.

  (3) then, unplug the unit and send images to the computer using WIFI.

  If this does not work because the shipment never ends, and then review:

  (1) the battery should not be weak, or if she is then connect the camera to the power supply.

  (2) the distance from the camera to the access point must be short (maximum of 3 meters), otherwise it is too slow.

• Cannot rename my PXI-4071 for something else that "PXI-4071" have the self-assessment work, and I can use the new name in the ivi drivers

  I tried to change the name of the PXI-4071 "DMM" that worked, but when I try to launch the "self-test" or open the app it Panel always fails.   This is also true if I pass the new name of the ivi driver.   Return to the name "PXI-4071" makes everything works again.   Note I managed to change the name of our PXI-2530 b 'SWITCH' and the name of our SMU-6363 to "MIO" and I could pass these names to their IVI drivers and they would work.

  I messed with alias VISA, IVI logical names, but nothing works unless it is called "PXI-4071.