connection PCI-6035E and SCB - 68 and controls a laser to turn

Similar Questions

• Can satellite P300 - I connect to a TV and control?

  Can I connect my Satellite P300 to TV hdmi-cec and control the laptop with the tv remote?

  Hello

  Connecting via HDMI cable should t be a problem. Just buy a high quality cable and connect both devices. With FN + F5, you can switch between monitors.

  Unfortunately I think that it of not possible to control the laptop through TV remote. The TV remote is designed for your TV, not your laptop. ;)

• Strange problem with analog output PCI 6251 and BNC-2110

  I'm controlling current source of third parties using the connectors of analog output on my card PCI 6251 and BNC-2110.

  The current source needs an input signal of 0.1V. I tested it using a battery, the potentiometer and the voltmeter, and by manually adjusting the voltage of power current works - current output with control voltage scales according to the specifications and is relatively stable.

  The data acquisition card works too - when I connect a voltmeter to the AO0 AO1, the measured voltage corresponds to the target with great precision value.

  But when I connect the current source of third AO0 AO1 data acquisition card, the measured output voltage drops and fluctuates. This applies to both channels of the AO.

  I wonder what is the problem here. I suspect it could be a matter of the grounding - the current analog control of the source is an entry with two floating terminals differential. I tried to return the switches FS/GS on the BNC-2110, but that makes no difference.

  Anyone knows similar behavior? Does anyone have any suggestions?

  
  

• Yellow brand - PCI Device' and 'Network controller' on the Satellite A100-787

  There is a yellow question mark in Device Manager for a pilot called "PCI Device" and also for "Network controller" even if the network (LAN) connection is working well and all the other computer functions seem to work well.

  What are these devices?

  The second device appears to be a LAN or WLan card. You should check if one of these cards were not installed under network adapters.
  The PCI device can be a card reader. Check this box too.

  But I really don't understand why these yellow exclamation points appear in Device Manager. I assume that you have installed all the drivers available. Did you?
  Please check if some drivers were not installed.
  If so, then download and install!

• PCI device and unknown device (code 28)

  After the installation of Wind8.1 my Hp 250 G2 (FOY89EA #ABE) lost the PCI device and when I connect to HDMI or VGA, no image is produced on the TV. How can I solve this problem?

  You are the very welcome.

  You need this driver that is not on your PC support and driver page...

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5405424&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_124774_1%257CswEnvOID%253D4158%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• I use an analog input on a PCI-6224 and are having problems with the clock source

  I use an analog input on a PCI-6224 and are having problems with the clock source. I'm trying samples of 16 different analog inputs very quickly. I have the sample mode: Timed Single Point material. The rate, that I am running is the maximum (250 kHz (15625Hz per channel)). I left the default clock source and trying to taste several times. The analogue input works for a short time (2-3 seconds) and then everything stops. I'm doing something wrong or is there something I'm missing? Any advice would be great.

  That's how you samples using the sample clock clock. If you see a delay then something is wrong with how you track/data visualization.

  Single point NI the hardware is for PID control with a real-time operating system.

• Question related to the entrance with pci 6221 and SCC 68 analog

  I use 6221 PCI and SCC 68 analog read of voltage between the terminals of the drain and the source of a transistor. The drain is at 0 Volt and source is connected to 5 volts via a 100 k resistor. The transistor is used as a follower of the source, and therefore the output is measured at the source of the Terminal. When I measure the voltage by using oscilloscope, I see clearly the change of output as a result of change of voltage of the door. But, when I try to acquire the same by using labview, I see nothing. I tried to change the signal to the CSR, NRSE, but nothing works. Seems to be that something related to differences in impedance. Can you please advice me on this issue? Thanks in advance

  Hi rsd111,

  I understand that you measure a circuit similar to this ( http://en.wikipedia.org/wiki/Common_drain)

  I also get that you use an external power supply with GND connected to the Drain and - 5V connected to the Source with a 100 k resistor.

  You should be able to measure the tension between D and S setup a differential measurement and connection Ai0 + D and Ai0 - s, in fact you can youse Ain you prefer.

  You should be able to do the same measure also at configuration NRSE linking Ai0 AiSense at the Source and drain.

  The Board's input impedance is greater than 10GOhm, it must behave as the oscilloscope in pairing mode high-impedance DC.

  6221 specifications: http://digital.ni.com/manuals.nsf/websearch/8117DF4C5A29C95C862573020061023B

  Nice day.

• Cable RTSI with PCI 6034 and 6602. Test validation of LabVIEW code.

  Hi all

  Please could someone take a look at my code (LabVIEW 8.5) and tell me if it does what I hope it is? (!)

  My goal:

  To connect to analog to a PCI-6034 and data of angular encoder to a PCI-6602 tensions. I want my tension and angle data to synchronize.

  My approach:

  Both cards are connected with a RTSI cable and configured in MAX. One of the counters on the 6602 is set up like a clock. I think I use this clock to make sure that my angles and tensions are synchronized. I want to read in a load of data from two sources, treat it, and repeat.

  The synchronization set is a little new to me - the code execution, but right now, I'm not sure if I get the sychronisation I need. Please what could someone comment if this sounds right or give me any advice for the improvement?

  Thank you!

  Ian

  

  Sorry Ian,

  This code was a bit thrown together then you might need to forget it. The table of construction was incorrect, and I don't quite know how it got there.

  The output of the counter in the middle of your task is not doing anything. You can remove this, and as long as you had a single start task depends on the other that you already do and share all the same settings of the clock, which should start the task at the same time and keep it synchronized to readings.

  On top of that my tip for better start synchronization would be to use a hardware trigger to start tasks. the start is so dependent on a hardware clock and not software.

  Kind regards

• Can a system using Windows XP Professional remotely help another system by using Windows 2000 Professional and control 2000 Professional computer to help solve the problems?

  Windows 2000 Professional has the capabilities of remote assistance?  My sisters husband just passed away and she doesn't know anything about computers.  All their documents, photos, ect..., my brother-in-law kept on the computer.  We live thousands of miles away and I can't fly to him.  Can I remotely access her computer and control it with mine that uses Windows XP Professional?  If the answer is "Yes", if you please tell me how to do it.

  Hello Jeff,.

  -Remote Office application do you use?

  You will be able to connect Windows XP computer to Windows 2000 via the remote desktop connection.

  I suggest you to check the following links for the desktop connection software remotely for Windows XP and Windows 2000.

  Windows XP Remote Desktop Connection software

  Configuration of remote desktop

• When I change how a user connects power on and off a screen appears saying "client for Netware has disabled the Welcome screen and the fast user switching. To restore these features...

  Original title: how to uninstall client services for netware?

  When I change how a user connects power on and off a screen appears saying "client for Netware has disabled the Welcome screen and the fast user switching. To restore these features, you must uninstall client services for Netware... But it is impossible to find... Help?

  Hello LindsayJune,

  Click the Start button.
  Click on Control Panel. Select network connections
  Right click on 'Connect to the Local network', then click 'properties '.
  Search for "Client Service for NetWare" slot "this connection uses the following items."
  Click it, and then click the "Uninstall" button
  Restart your computer.

  Uninstall client for Netware feature will allow the option of quick change of user on your computer.

  I hope this helps.

• My WMP said that I need to connect a burner and restart the player?

  For long time now Ive been burning cd and just recently my WMP started getting a message saying I needed to connect a burner, and then restart the player. It goes the same for extraction, he said "A CD DRIVE IS NEEDED in order to RUN RIP". I don't know why he started to do this, he has never been a problem before. I have a laptop HP Pavilion with Vista Home Premium. Is there anything I can do to restore or solve my dilemma? Advice or answers would be useful.

  Thank you
  Mike

  Hello

  Step 1: Please make all underneath the same if you've done it before as it's often the total of the process which
  solves the problem. Start at the top and use it as a checklist to the drive works and not jump around like a menu.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  If necessary:

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry entries
  that the troubleshooter does not, and those who "could" be the cause.

  Check with your system manufacturer Maker and device for possible firmware updates and the good
  Your player registry entries.

  Here are the keys in my opinion, are those in question - for the reader of CD/DVD subkeys of course that he will be
  other subkeys in these keys. Be sure to ask specific keys involved as well as the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even registry settings correct for your CD/DVD drive
  a person with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• What to do if your computer has been hacked or hacked and controlled by a remote elsewhere.

  Original title: hijacked, hacked into the computer

  What to do if your computer has been hacked or hijacked and controlled by a remote connection

  Furthermore.  Many different programs added and if I try to uninstall or remove programs I don't recognize
  I'm being denied access.  I have cleaned, restored and repaired my computer several times and it keeps
  happens to me on my laptop and my PC computers.   my user name is not changed, but the control
  is not outside of me and they're using my name.  Can anyone help?

  You must save your stuff important on an external and reinstall your entire system since the manufacturer's recovery partition. You can find instructions for this on the site of manufacturer support.

  If you have no recovery partition, follow...

  http://Windows.Microsoft.com/en-CA/Windows7/installing-and-reinstalling-Windows-7

  Immediately after having re-installed, the next task is to make all Windows, including SP1 updates if your floppy drive or the partition recovery date before the service pack.

  Then install your antivirus solution. Avoid using McAfee or Norton. It is a good solution, free and easy to use...

  Microsoft Security Essemtials... http://Windows.Microsoft.com/en-CA/Windows/products/security-essentials

  OK so far?

  Then, change the passwords for all programs that interact with the Internet... This includes Facebook, Windows Live Messenger, Yahoo Messenger, Skype etc.

  When you create a password, do NOT use real names and use a combination of numeric characters and alphabet, up and down case. It must be complex enough so that he could not be found in a dictionary, but not quite complex that you don't remember it...

• I want to access and control my other laptop with wifi.

  * Original title: remote access

  I don't know anything then please help me from 0. I want to access and control my other laptop with wifi. I don't know where to start? Please?  Reference Dell w7 while the other is toshiba w8.

  (Moved from devices and drivers)

  You can do this with Remote Desktop.

  These can be useful:

  Remote Desktop connection: frequently asked questions

  The application of remote desktop help

  Remote Desktop in Windows 8

  John

• Photoshop CC 2015 is a line connecting the start and end of the brush strokes

  Hi guys,.

  I had a strange problem with a certain brush (size 5px, difficult tour, no shape dynamics, no transfer) in Photoshop CC 2015.1.2.

  It only happens when the drawing very fast on my Cintiq 22HD.

  The problem is PS is a line connecting the start and end of the brush strokes. I don't hold in shift or whatever it is.

  

  Here's my brush settings:
  

  I use a PC with these specs:

  Intel Core i7 - 4790 K 4.00 GHz

  ASUS motherboard

  NVIDIA GeForce GTX 970 (10.18.13.5354 driver version)

  16 GB OF RAM

  Cintiq 22HD

  Win 10
  

  Is it a question of PS or Cintiq?

  Thanks for help.

  OK, here is therefore an update.

  The problem is not at all with Photoshop or Cintiq, with Windows 10 parameters of the stylus.

  Fortunately, there is a small piece of free software that you can download called "Fix my pen" (by Smith Reddy) which defines the features of Windows Tablet PC in the registry for you (essentially by disabling everything related to it):

  viziblr - News - difficulty my pen makes your Wacom tablet JUST WORK on Windows 7

  It works fine on Win10 too.

  Now, as my original problem with Photoshop to do a line connecting the start and end of the brush strokes left, however I have another question more small that came after running difficulty my pen. The lines that I draw now are not smoothed by a software more. You can see the difference below.

  

  Fix My Pen sets a lot of things in the registry, but you cannot individually control which setting is disabled. So I guess that one of them is the cause.

  

  I expect response from Smith about it, cause I have no idea who he is.

• strategy of redo and control files

  Excuse my ignorance in this area (not oracle or a DBA), but from a risk perspective, I read his best practices for storing a redundant copy of recovery logs and control files on a separate disk / server - for redundancy.

  However, if the server is a server database physical, with local storage (in which case files of database and the oracle software resides), no configuration of cluster if the server dies a sudden death, then what exactly are the newspapers redundant recovery and control of files will save you of? Is it to minimize the loss of data, or else (told you I wasn't a DBA or Oracle guru). If you back up your recovery connects dialy then I don't know what exactly the redundant copies really are for/record you leave?

  So if the server dies (and the storage is still ok) and then transport the storage to another server and you are in business again. Multiplexing or not does not change your ability to use another server.

  In a disaster situation, where you lose the server and the storage is also lost, so you have to go to a backup and multiplexing saves you from what it is because the backup has only 1 copy of the controlfile and archivelogs.

  If you get a logical corruption (IE a bug in the software) with controlfiles multiplex, then you're still screwed because all controlfiles are physical copies of each other, so all controlfiles have the same corruption. In this case, you must go to a good backup of the controlfile.

  Multiplexing allows you to save when you get corruption Physics (due to the corruption of storage) of your command multiplex or multiplex redo logs file, and so you can use the good copy of the file control or redo logs to continue without losing the validated data.