Control reference 1055 error when you use a loop for

Similar Questions

• IMAQ Grab Acquire.vi error when you use an external trigger on a card NI PCIe-1433 (sync problem?)

  According to my recent post on getting up and running with the NI PCIe-1433 camera link card, I ran into a bit of a snag.

  When you use the internal trigger on the camera, everything works 100%. I can view all the data from the camera in MAX as well as in the labview project. However, whenever I have set the mode switch is where things start to fall apart.

  What I have confirmed:

  -Camera is switching between inside and outside triggering.

  -NI PCIe-1433 camera link card is set up properly. While in external mode, I can trigger the camera by using a function generator and check the wire to the MAX. Everything works fine.

  When the unit is in external mode, the function Acquire.vi enter IMAQ - my mistake VI. The error is:

  Code :-1074397150

  The possible reasons for a timeout.

  Now, I have it set up so that a mistake here will not end the LabVIEW file. Sometimes, data of interest makes however (about every 10 seconds-ish). So what seems to be the case, it's that this external trigger signal is not in the lineup when the clamp is attempted. Is it possible to synchronize these? May reference the trigger signal external sort in my LabVIEW project so that the clamp is performed only when that trigger impulses?

  So I solved my problem. He was in time. The external trigger that I used for the device was simply too slow. I was initially using a trigger from 2 Hz to be able to view the values changing on LabVIEW probes. But it was enough to get enough data to move above the camera cable to assemble a picture and kept it in time. Travel up to 9 kHz solved the problem. No adjustment to the camera settings or LabVIEW code was necessary.

• TWAIN errors when you use Canoscan3200F on Win7

  I get error TWAIN when you use Canoscan3200F on Win7. Tried to use Canoscan Toolbox 4.5, Irfanview 4.32 and Windows Fax & Scan - all give variations of the TWAIN error, bascially do not recognize the scanner, even if it looks OK in Device Manager.

  CanonScan said - could not open TWAIN source.

  IrfanView, said - rmslantc.dll missing.

  Windows Fax Scan & said - no scanners not detected.

  Hi the string 1,

  Make sure that a certain folder path is in the PATH environment variable. Follow these steps:

  (a) first, to determine the correct path to add to the PATH environment variable.  Look in C:\Windows\twain_32 and there should be another folder (example:-CNQ4803). This is the way that is needed to be added to the PATH environment variable. C:\Windows\twain_32\CNQ4803

  (b) alter the PATH environment variable. Go to Control Panel, Systemand then choose Advanced system settings in the left column.

  (c) this will bring up the System Properties dialog box (it should already be in the Advanced tab).

  (d) at the bottom of this dialog box is a button Environment Variables .  By clicking on this button to display the Environment Variables dialog box.

  (e) in the bottom panel, scroll down until you find the variable named Path.  Select it and then press the Edit button to bring up the Edit System Variable dialog box.

  (f) in the Variable value text box, scroll all the way to the right, and then add the C:\Windows\twain_32\CNQ4803 path that was determined earlier.  Be sure to separate this value by a preceding semicolon.  And also be ensure not to make further changes to this value. Click OK.

• I keep getting out of memory errors when you use Windows Media Player.

  original title: of memory error

  Hi, I have a Windows 7 PC brand new with 12 GB of RAM, but I get low on errors of memory, especially when you use Windows Media Player. I tried:

  -Execution of the antivirus scans

  -Cleaning things out of the startup folder

  -Increase in the size of paging file

  I can't understand what the devil is the cause of this error - as I said, it's a new machine, and is not practically nothing on it yet.

  Any help is appreciated.

  Hello

  Follow these steps and check.

  (a) open 'command prompt' as an administrator (programs, accessories, right-click "command, prompt" run as administrator).

  (b) type the following without the quotes and press ENTER.

  "for %a in (% systemroot%\system32\wm*.dll) do regsvr32 /s %a.

• Error when you use the feature Version «Back upward in a file»

  I run an error when you try to save a file version. The error is below to:

  There was an error trying to get the status of the job.

  1: the server returned an error during the processing of the action: CloseJob. Error message: String reference not set to an instance of a string.

  Parameter name: s

  As you can tell, he didn't give me much to do.

  Some background information:

  -J' trying to backup/export a version that has been upsized QA development

  -QA and development have the same version/patch 11.1.2.3.500

  -This version has been imported into the development, and then copied, and then mixed with a development version.

  -I did not receive any errors during this process

  -I am able to backup other files without getting this error

  Any help will be really appreciated.

  Thank you

  Aaron

  Hi Aaron,

  At first glance, it looks like there may be a string of property that is not a string data type. However, before you dig too deep, try to reload the version to see if that makes a difference. I had a similar problem before and it is solved.

  Thank you

  Jordan

• get the error when you use the TRIM method in the collections

  Hi Experts,

  When you use the TRIM method I get below error. I make any mistake here?

  DB: Oracle 11g

  SQL > declare

  2

  emp_tab of type 3 is the employee table % rowtype index directory.

  4 l_emp_tab emp_tab;
  5

  6 start

  7

  8 select * bulk collect into l_emp_tab of employees;

  9 l_emp_tab.trim (5);

  10 dbms_output.put_line (l_emp_tab.count);

  11

  12 end;

  13.

  l_emp_tab. Trim (5);

  *

  ERROR on line 9:

  ORA-06550: line 9, column 2:

  PLS-00306: wrong number or types of arguments in the call to 'TRIM '.

  ORA-06550: line 9, column 2:

  PL/SQL: Statement ignored

  Thanks in advance for your help.

  See you soon,.

  Suri

  For PL/SQL collections "index by" you cannot use the TRIM function. If your collection statement excludes the portion "index of...» ", then you can.

  Gerard

• error when you use the Export-CSV cmdlet

  Hello

  I get the following error when you try to pipe the output to a csv file

  " Could not bind the parameter argument 'InputObject' because she's nowhere.'"

  The output is placed in the csv file, but I get this error at the end of the script.

  Here is the code:

  ##Variables

  ###################################

  $report = @)

  $CSVfile = "d:\Vm_Report.csv".

  $VMs = get-vmhost | Get - VM

  ###################################

  {foreach ($VM to $VMs)

  $VMx = get-view $VM.ID

  $HW = $VMx.guest.net

  foreach ($dev to $HW)

  {

  foreach ($ip in $dev.ipaddress)

  {

  $report += $dev. Select @{Name = 'Name'; Expression = {$vm.name}},@{Name = 'IP address'; Expression = {$ip}}, @{Name = 'MAC'; {Expression = {$dev.macaddress}}.

  @{Name = 'Property DL'; Expression = {$vm. CustomFields}}

  }

  }

  }

  $report | Export-CSV - NoTypeInformation $CSVfile

  Thank you

  The attached script implements the test of the $HW variable.

  In my test environment, Export-Csv now works without any problem.

  Give it a try.

• How to disable direct sound when you use a plugin for guitar?

  I use the Waves GTR plugin for recording guitar in Logic Pro X, but because it puts a lot of pressure on the CPU, I tried he governs through a "bus" instead of having the plugin separately on every guitar track. The difference is that when I use the bus option, I can't seem to get rid of dry direct sound which is obviously very embarrassing. The only way for me to get rid of the direct sound is to use the RTM plugin on every guitar track that quickly causes the overload program when using several of these titles.

  Anyone know how to get rid of the direct sound when you use the alternative of bus for the guitar tracks?

  just at the exit of the guitar channel strip no output. This way you won't hear at the follow (because the dry track will not be transmitted to any output)

• When you use the search for a window, the files are not listed in the search index

  Original title: question of Windows search

  When you use windows search, records that are not not in the search index are searced. Why?

  Hello

  1. What is the operating system installed on your computer?

  2 are there any changes made recently to the computer?

  Improve Windows searches using the index: frequently asked questions: http://windows.microsoft.com/en-US/windows7/Improve-Windows-searches-using-the-index-frequently-asked-questions

  You can also check:

  Reconstruction of Index of Microsoft Windows 7 search: http://windows.microsoft.com/en-US/windows7/Change-advanced-indexing-options

  Advanced Tips for searching in Windows

  http://Windows.Microsoft.com/en-us/Windows7/advanced-tips-for-searching-in-Windows

  I hope this helps.

• Unable to get into the MSN account or by mail WHEN you use Norton connection for security reasons. I can't add attatchments.

  I use Norton Secure login. MSN & mail is the only site that I can't access. This mind by scary business monitoring, MSN? Sorry ' end that.  I can't add attachments to the e-mail message. Apparently, there are many of us with the problem of attachments. Why I use msn? anyone?

  Hello

  Thanks for posting the request in the Microsoft community forums.

  It seems that you are not able to MSN account or by mail when you use the connection of Norton.

  You can try to disable Norton antivirus installed on the computer and check is that you are able to connect to MSN and email.
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
  NOTE: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable the antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  We know if you need help with Windows. We will be happy to help you.

• Error when you use the Group feature

  Oracle forms6i
  
  Hai
  
  While I compile my coding it will compile correctly, but when I tried to run I revealed an error in the function of group
  
  my code is
  
  
  If (NTC <>0) then
  Select the BAR code, RESPONDENT, OUTTIME today_bar, today_in, today_out from dail_att where BARCODE =: bar code
  and ATTEND_DATE =: bardate;
  Update dail_att set outtime = max(:bartime) where barcode =: bar code
  and ATTEND_DATE =: bardate;
  
  on the other
  If (cnt2 <>0) then
  
  Select RESPONDENT, OUTTIME in yest_in, yest_out from dail_att where BARCODE =: bar code
  and ATTEND_DATE =: bardate-1;
  
  If (yest_in is not null and yest_out is null) then
  Update dail_att set outtime = max(:bartime) where barcode =: bar code
  and ATTEND_DATE =: bardate-1;
  
  on the other
  insert into dail_att(barcode,intime,attend_date)
  values (: Barcode, min(:Bartime),: bardate);
  end if;
  on the other
  If: bartime between 0100 and 0630
  insert into dail_att(barcode,intime,attend_date)
  values (: Barcode, min(:Bartime),: bardate-1);
  
  Update dail_att set outtime = max(:bartime) where barcode =: bar code
  and ATTEND_DATE =: bardate-1;
  
  on the other
  
  insert into dail_att(barcode,intime,attend_date)
  values (: Barcode,: min (Bartime),: bardate);
  end if;
  end if;
  end if;
  
  while I'm trying this groupfunction it throws error while I use seen tell me how to use the Group feature and where
  to use
  
  Regadrs
  
  Srikkanth.M

  Srikkanth,

  For this you need to calculate the max outside of the update statement and then use this value in the update statement.

  The bartime is a control in the block?

  If Yes, then you need to find the max manually, and if it isn't, then you can write a sub query to find the maximum value.

  Kind regards

  Manu.

  If my response or response from another person was helpful, please mark accordingly

• Error Msg: "there was a problem sending the command to the program" when you use a shortcut for FireFox

  This only happens when I use a shortcut to call Firefox. I am running Windows 7 Professional. The Firefox window opens after the error message occurs, so I would class this as a gene.
  Many help comments mention 'ddeexec' removal of Firefox registry entries. It worked for a while (it seems to be related to updates of Firefox), but now no longer works: ddeexec is removed, but the error message persists.

  I found a fix for Win 7 (x 64) based on two observations:

  1. the waiting period does not exist if Firefox is already running.

  2. There are (at least) two types of shortcuts: Application and URL. When Firefox is the default browser, shortened URL get a timeout message. A the application shortcut to Firefox works without any problem.

  Follow these three steps to create a new shortcut that runs Firefox with the URL as a command:

  1. create a shortcut to the Application either by copying an existing shortcut, or right-click on the desktop, select new | Contextual and choose the location of Firefox.exe.

  2. then right click to open the new shortcut, properties. On the shortcut tab, you will find:

  Target: "C:\Program Files (x 86) \Mozilla Firefox\Firefox.exe.

  Start in: "C:\Program Files (x 86) \Mozilla Firefox".

  3. copy the URL address, type a space after the quotation marks of the target and paste that URL, it should look like this:

  Target: "C:\Program Files (x 86) \Mozilla ' http://postini.com

  I used a short URL to this example to fit on a single line, but the useful commands can be much longer; for example:

  https://login.Postini.com/exec/[email protected]

  The second example opens a connection to Postini spam filter window and between your email for you. Below is a screenshot of a tab popup properties shows in the middle of the target where Firefox ends the line, and the URL starts.

  -Jim

• "27049 internal error" when you use recovery with Equium A60-692 utility

  TOSHIBA SATELLITE A60 - 692

  I'm trying to fix a friends laptop. The laptop computer wouldnâ? t start, would go to the blue screen just before the came WinXP loading screen then will re-start. I used a USB 2.5 HDD enclosure "to copy important files on my laptop and then formatted the drive of my laptop. I put the HARD drive in the Toshiba and have used the CD of restoration via an advanced option. on exactly 9mins 50sec time on the recovery process, an error message appears (27049 internal error). After that, it goes to a screen of style BACK with a little more information. Essentially by specifying that the error is "cannot read FILE_BITMAP MFT entry.

  I cleaned the CD
  I swapped the CD drive with my laptop
  Quick formatting it formatted, it is full
  Used the basic option where it does itself and it ERRORS with - not enough space on the partition - there is no partition! or if there's empty sound

  What can I do?

  Hello

  I think that the HARD drive is broken, because if you receive an error message with words like "MFT" (meaning MasterFileTable) then you can expect that the HDD has serious problems.
  OK, easy to talk to it s fast without knowing the machine and so on, but I know a similar error and I can give you the advice to probe hard disk errors.
  You can do this with the help of the "ultimate boot cd" which is a very interesting tool when you need information about your computer or you want to just check if everything works well.
  Here´s the link to the downloadable CD image that should be on a CD:

  http://www.ultimatebootcd.com/

  Hope you can solve this problem...

  Welcome them

• How can I fix the cannot find server error when you use Bing?

  When I want to use Bing as a search engine, I always get an error message cannot find server. When the connection problem is diagnosed, the result is that there is not a problem with the connection. I get the same thing when I use the Google search engine. OT most of the time I'm successful search with Ask. I use Windows XP.

  Hi MineMN,

  ·         Did you do changes on the computer before the show?

  ·         What web browser do you use?

  If you are using Internet Explorer, follow these methods.

  Method 1: Follow the steps in the article.

  "Internet Explorer cannot display the webpage" error in Internet Explorer

  Method 2: If you still face the same problem reset the TCP/IP stack.

  How to reset the Protocol Internet (TCP/IP)

  Method 3: Reset the proxy server. Follow these steps:

  (a) click Start, run, type cmd , and then press enter.

  (b) type the following commands at the command prompt and press enter after each command:

  proxycfg d

  proxycfg-u

• How can I remove J2SE Runtime Environment 5.0 update 11. Application of transformation error when you use Add/Remove programs

  Cannot remove J2SE Runtime Environment 5.0 update 11 or Java or Java 2 Runtime Environment SEv1.4.2_6.

  Add/Remove Programs DOES NOT WORK.  Message received when you try to remove programs is, "error application of transformations".

  Java (TM) 6 Update 21 is installed on my computer.

  Please let know us the step by step procedure to remove the old Java programs.  Thank you.

  E-mail address is removed from the privacy *.

  use revo uninstaller