Could not start VM after P2V of Windows XP in ESXi 4 using vConverter Stand Alone 4

Similar Questions

• I have a windows computer 7 and when I boot it says windows could not start then he normally open windows or repair.

  * Original title: windows startup

  Hi I have a windows computer 7 and when I start it up it says windows could not start then it says windows normally or repair I choose windows star normally and his coming as a code error 0x0000005c and I did they opsen others, but still the same error code I just wanted if I can back up my photos because they are good, or I can try to solve this

  Thank you

  The BIOS back to their default level settings.

  • Make sure that all internal cables, cards, and other components are installed and correctly.
  • Start your PC with essential hardware only.

  If no change:

  Perform Diagnostics on the memory and hard drive tests.

• WAG300N: could not start correctly after power failure

  Hello

  After AC power interruption, I tried to turn on my router Linksys WAG300N, but he won't start properly. I will describe what it looks like and what I've tried:

  I push the power button / stop, all 4 Ethernet LED simultaneous light for about a second, (if there is LAN cable connected, one or more led lights permanently) and power the LED will blink twice at normal speed. After that, both voltage and wireless, led simultaneously for about 1-2 seconds, start power LED flashes quickly, after seconds wireless LED stop light, wireless flash LED again and stop two LEDs for lighting. Second later power LED flashes two times normal speed and the process begins again but without flashing of the LED Ethernet (loop).

  I tried to download the firmware using TFTP, but it does not work. Router did not respond to a ping. After many tests, I noticed that the only time where I can ping router is during normal those two blinks of the power led. I've got 11 times waiting and the response of 1 or 2<1ms, 11="" timeouts,="" 1="" -="" 2="" responses etc... (response="" waiting="" time="" for="" a="" ping="">

  I've tried a few ways to reset the router (based on this forum). It does not help, sometimes after the reset I power the router problems or flashing process stops after a few loops (only one Ethernet LED lightning or router turns off). At the end of a day all supports them to the previous behavior of closure with power LED and wireless LED blinking.

  In the end, I tried utility upgrade Sercomm 2.07 mentioned in this topic: http://forums.linksys.com/linksys/board/message?board.id=DSL&thread.id=52

  This software detects only router after reset, when the router is in unknown mode, Internet and power LED flashes alternately.

  Software detects the device as MAC address and visualize correctly the version of firmware loaded into memory. Looks like it works and flashing memory. While flashing memory, power LED, LED Internet and Ethernet LED flashing at the same time very fast. I tried all versions of firmware available, but it does not help, I still have the same behave after flash.

  I think it could be a problem with the bootloader, maybe that part of the memory is broken, but I did not how to fix it. I found information on the JTAG interface, but I don't know if it will work for router WAG300N and where I can find the appropriate file with bootloader.

  Maybe someone can help and give me the idea what should I / check. Theoretically, I should have left 1 year warranty, but I lost the proof of purchase required for the RMA process. I can't find the place in Poland where professionals can help me, so I think that should do it myself with your help

  I think that's the problem with the power adapter... You should try a different power of the specification of the same card...

• Help! VM does not start successfully after the conversion of Server VMware ESXi 4.1

  Hi, I have install my first server ESXi, everything seems OK and stable. Had a few PtoV machines, but to start I thought I propose our only current VM from VMWare server on our ESXi server.

  The VMware host is Win2003/32 running VMware server 1.0.6 and the prompt is also Win2003/32. I shut down the VM, installed the stand-alone converter on the VMware host and let it do it's thing. Successfully completed and took 20 minutes.

  When I try to start the virtual machine of the ESXi server, it looks OK, but hangs on "Application Startup Scripts", possibly the login screen appears, but then I get messages from "Remote RPC server not available" when you try to open an RDP session. A local login hangs right on the application of personal settings.

  Network everything seems fine, can ping the VM, etc.

  May not work on why the virtual machine should start any differently? Any ideas, anyone please. I am new to ESXi and migrate the virtual computer, but have used VMware Server a lot in the past.

  All advice appreciated...!

  That's good news.

  Which explains, normally, you must do the VMTools upgrade, then the virtual machine hardware, so if the converter upgrades the equipment, the order is bad. Of course, it is recommended to upgrade the hardware to ver 7. So now that it works you can improve the tools and then the vHardware. It might be interesting, if you have enough resources on the ESXi host, make a clone to the virtual machine and the test on the clone in a State (disconnect vNIC) offline.

  Please allow Points if it is useful

• My macbook pro could not start even after various combinations of keys

  After referring upgrade to the macbook pro mid 2011 for OS X 10.11.15, I have to do a lot to restart, as well as the different key combinations in order to get mac (even that becomes difficult to solve the problem now!) I tried the diet, Ctrl + R, Shift + Ctrl + S, Shift + Ctrl + R + P, etc.. Although this may work from time to time, I am particularly concerned when I do school work timely.

  What is responsible for this and how can it be solved?

  When your Mac "not getting", what exactly do? What told you it does not work properly?

• Want H8-1534: could not start HP Envy H8-1534 pc after Windows update 10, 1607

  Windows 10 has made automatically update 1607 (KB3176936) on the pc of my wife (HP Envy H8-1534) about 6 days ago. Since then I could not start the pc the first time I turn it on.

  When I hit the power button on the monitor lights up with the HP logo on black screen as usual but the loading icon (spinning points) does not start. Fans start, but there is no activity on the Tower in the way of flashing lights or beep sounds. If I turned off the pc by using the power button, wait 10 seconds and turn on again, the pc will start up as normal. So far, for the last 6 days, it took the 2nd attempt so that it starts the pc every time. It almost seems as if there are not able to go to the system except for the fans in this first attempt to start.

  I ran a test at startup by pressing the F2 key without no problems found. I disabled the SATA power management in the BIOS. I ran the Windows startup with no result repair. Here are the results of the txt file.

  I researched all the possibilities. I fear that this could begin to worsen. Any help will be appreciated.

  Name: Target OS Test
  Result: Completed successfully. Error code = 0 x 0
  Time taken = 265 ms
  The test is performed:
  ---------------------------
  Name: Checking content Volume
  Result: Completed successfully. Error code = 0 x 0
  Setting time = ms 2391
  The test is performed:
  ---------------------------
  Name: Diagnostic Boot manager
  Result: Completed successfully. Error code = 0 x 0
  Time taken = 63 ms
  The test is performed:
  ---------------------------
  Name: Diagnosis of the system startup log
  Result: Completed successfully. Error code = 0 x 0
  Time = 0 ms
  The test is performed:
  ---------------------------
  Name: event log diagnosis
  Result: Completed successfully. Error code = 0 x 0
  Time taken = 62 ms
  The test is performed:
  ---------------------------
  Rated: Internal audit of State
  Result: Completed successfully. Error code = 0 x 0
  Time = 0 ms
  The test is performed:
  ---------------------------
  Name: Start-up condition Test
  Result: Completed successfully. Error code = 0 x 0
  Time taken = 31 ms
  Root cause found:
  ---------------------------
  State the start indicates that the OS booted successfully.
  ---------------------------
  ---------------------------

  DBHPENVY,

  I turned off quickly startup on the pc and until now he started first try twice. I'll let you know how it does after a few days of testing.

  I read everything it does and it is perfectly logical, how it might affect our pc is the way. Go to this link and read about it and see if she could help. I thought I had turned off fast start already, but after an update he might have gotten turned on.

  Here is the link: http://www.tenforums.com/tutorials/4189-fast-startup-turn-off-windows-10-a.html

• PC with Windows Vista does not restart after installing updates, "Windows could not start...". "File:\Windows\system\winload.exe status: Oxcoooooof.

  Last night, I installed Windows updates on my HP Pavilion dv6227cl and now Windows will not boot.  I get the message "cannot start Windows.  A recent hardware or software change might be the cause.  File:\Windows\system\winload.exe status: Oxcoooooof Info: the selected entry could not be loaded because the application is missing or damaged.  I DO NOT have the Windows Setup disc.

  Hello

  I suggest you borrow the CD of windows vista to your friends

  Method 1:

  Step 1:

  I suggest you check in safe mode.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2:

  If you be able to start your computer in safe mode, I'd say make clean boot and check.

  Place the computer in a clean boot state, then check if it helps. You can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, make sure the computer to start as usual as mentioned in step 7 in the above article.

  Method 2:

  I also suggest you to see link and check.

  Error: Windows could not start. A recent hardware or software change might have caused the problem after installing Windows updates

  http://support.Microsoft.com/kb/2674065

• Windows could not start after activating the boot.

  Hi all

  I have a very serious problem.

  A few lost technology from Microsoft asked that I have to do the following:

  http://support.Microsoft.com/kb/929135.

  Immediately after the restart, I was confronted with the following message:

  Windows could not start.

  Status: 0xc000000e

  Info: A required device is not connected or is not accessible.

  Startup Repair does not work. -Root cause found: the partition table has not a Sys component validates.

  System Restore does not work - the system cannot find the specified file (0 x 80070002)

  Bootrec - rebuildbcd works no item was not found.

  Bootcfg does not work - could not open the TRUNK. INI file.

  Bcdedit does not work - the requested system device cannot be found.

  GParted does not work - cannot load the ntfs module: invalid argument.

  How can it be fixed, please?

  It is an extremely urgent situation which must be resolved immediately, because I use this computer for work and need to return to work on a large commercial project Monday. Forget the original question that MS tech was trying to 'help' with, everything what I need now is to be able to get into Windows, or even just make this record available and accessible on the LAN computer.

  Hi all, thank you for the advice.

  Problem has been resolved after a cold start.

• Try reinstalling firefox on a windows machine 7 and I get «the application could not start correctly (0xc0000142)»

  To solve a different problem, I uninstalled Firefox. After you have solved the other issue I'm tying to re - install Firefox and get an error message that says that "the application could not start correctly (0xc0000142). Click OK to close the application. "The title bar of the window, said"setup - stub.exe - Application error. "My PC is a Dell Studio 19 all-in-one running Windows 7 Home Premium.

  I ended up solving this problem by doing a reinstall on Windows 7 site. It took a little while but fixed this and a few other issues I've had.

• Qosmio G45-AV680 - Windows could not start

  My cousin has this laptop and could not start the system. It displays the message:

  "Unable to start Windows. A recent hardware or software change might be the cause. To solve the problem:

  1. Insert your windows installation disc and restart your computer.
  2. choose your language settings, and then click "next".
  3. click on "Repair your computer."

  If you don't have this disk, contact your system administrator or computer manufacturer for assistance. Status: 0xc000000f

  "Info: the boot selection failed because a required device is not accessible.

  I tried to go into safe MODE, but it cannot do so. It starts to load the drivers, but it stops at some point and will not continue...
  The problem is that she did not have any DVD with laptop. I guess that the Vista operating system, that comes with it is the special partition on the hard drive, but how can I access it? How can I reinstall the system? I don't mind if I lose data, I used just to make it work...

  If DVD recovery is not assured that means installation of recovery can be started from the HARD drive. I don't know how it works exactly on cell phones in the United States. Try pressing zero button after starting upwards to see if HARD drive recovery option can be started.

  By the way: check the Toshiba U.S. support under http://laptopforums.toshiba.com/tshb/ forum
  Maybe someone there can explain how it works to start the installation of the OS on the HARD drive.

• Could not start the time service windows on the local computer 2 error

  Cannot update the system clock of time Internet.

  After double click to display the time in the taskbar, the Date and time properties window appears.

  Then I time tab-click Internet, and then click Update now - this produces the following message...
  "Year error occurred getting the status of the last synchronization." The RPC server is unavailable ".
  Then I clicked on start > Control Panel > Administrative Services > Services > time Windows
  I click Start the service and get the following message...
  "Could not start the time service windows on local computer."
  "error 2: the system cannot find the file specified."
  Help!  What now?

  Hello

  Glad to know that the problem has been resolved. If you have additional questions on the computer, please ask your question about Windows and we will be happy to help you.

• Windows ICS Services stopped & could not start the windows firewall in windows xp professional sp2.

  I am facing a problem regarding the ICS Service & could not start windows in windows Xp service pack 2 firewall, whenever I have install windows Xp Sp2 and join the network, the ics services ceased and the windows firewall. While windows firewall service starts when I restart my computer. But after some time stopped again had services that I'm cold does not access the readers of part, could not access network resources.this problem occurs only on windows xp sp2, when I install windows 7, then all better.i work fetch on different forums, apply the settings but I'm not able to solve the problem on base all the time. Someone tell me the permanent solution of this problem, on a forum, I see this solution,sharedaccess.reg and settings.but I am still unable to find a permanent solution.

  Someone tell me the permanent solution of this problem?
  
  
  
  

  Hello

  Here are a few troubleshooting steps that you can try to solve this problem. See the following links.

  You cannot start the Windows Firewall service in Windows XP SP2

  http://support.Microsoft.com/kb/920074

  Registry WARNING: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see this link:

  http://support.Microsoft.com/kb/322756

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users

  http://support.Microsoft.com/kb/875357

  If you have additional problems, please reply to this post and we will be happy to help you further.

• most programs now get error message "could not start from this location after a mail there is session 2 nite".

  After a session 2 nites E-mail there, many programs said message error "could not start program from this location. In addition, long delays after you clicked on a link, a large display hourglass for up to several minutes. Have tried to rebuild, but I think that the problem is still there. Any suggestions?

  What is a "mail session?

  What is, "have tried to rebuild?"

  Edition with Service Pack of Windows XP _ _?

  What anti-virus application that you use, and if she slept in day?

  Search for malware:

  Download, install, execute, update and perform analyses complete system with the two following applications:

  • MalwareBytes (FREE)
  • SuperAntiSpyware (FREE)

  Remove anything they find.  Reboot when necessary.  (You can uninstall one or both when finished.)

  Search online with eSet Online Scanner.

  The less you have to run all the time, most things you want to run will perform:

  Use Autoruns to understand this all starts when your computer's / when you log in.  Look for whatever it is you do not know using Google (or ask here.)  You can hopefully figure out if there are things from when your computer does (or connect) you don't not need and then configure them (through their own built-in mechanisms is the preferred method) so they do not - start using your resources without reason.

  You can download and use Process Explorer to see exactly what is taking your time processor/CPU and memory.  This can help you to identify applications that you might want to consider alternatives for and get rid of all together.

  Do a house cleaning and the dust of this hard drive:

  You can free up disk space (will also help get rid of the things that you do not use) through the following steps:

  Windows XP should take between 4.5 and 9 GB * with * an Office suite, editing Photo software, alternative Internet browser (s), various Internet plugins and a host of other things installed.

  If you are comfortable with the stability of your system, you can delete the uninstall of patches which has installed Windows XP...
  http://www3.TELUS.NET/dandemar/spack.htm
  (Especially of interest here - #4)
  (Variant: http://www.dougknox.com/xp/utils/xp_hotfix_backup.htm )

  You can run disk - integrated into Windows XP - cleanup to erase everything except your last restore point and yet more 'free '... files cleaning

  How to use disk cleanup
  http://support.Microsoft.com/kb/310312

  You can disable hibernation if it is enabled and you do not...

  When you Hibernate your computer, Windows saves the contents of the system memory in the hiberfil.sys file. As a result, the size of the hiberfil.sys file will always be equal to the amount of physical memory in your system. If you don't use the Hibernate feature and want to reclaim the space used by Windows for the hiberfil.sys file, perform the following steps:

  -Start the Control Panel Power Options applet (go to start, settings, Control Panel, and then click Power Options).
  -Select the Hibernate tab, uncheck "Activate the hibernation", and then click OK. Although you might think otherwise, selecting never under "Hibernate" option on the power management tab does not delete the hiberfil.sys file.
  -Windows remove the "Hibernate" option on the power management tab and delete the hiberfil.sys file.

  You can control the amount of space your system restore can use...

  1. Click Start, right click my computer and then click Properties.
  2. click on the System Restore tab.
  3. highlight one of your readers (or C: If you only) and click on the button "settings".
  4 change the percentage of disk space you want to allow... I suggest moving the slider until you have about 1 GB (1024 MB or close to that...)
  5. click on OK. Then click OK again.

  You can control the amount of space used may or may not temporary Internet files...

  Empty the temporary Internet files and reduce the size, that it stores a size between 64 MB and 128 MB...

  -Open a copy of Microsoft Internet Explorer.
  -Select TOOLS - Internet Options.
  -On the general tab in the section 'Temporary Internet files', follow these steps:
  -Click on 'Delete the Cookies' (click OK)
  -Click on "Settings" and change the "amount of disk space to use: ' something between 64 MB and 128 MB. (There may be many more now.)
  -Click OK.
  -Click on 'Delete files', then select "Delete all offline content" (the box), and then click OK. (If you had a LOT, it can take 2 to 10 minutes or more).
  -Once it's done, click OK, close Internet Explorer, open Internet Explorer.

  You can use an application that scans your system for the log files and temporary files and use it to get rid of those who:

  CCleaner (free!)
  http://www.CCleaner.com/
  (just disk cleanup - do not play with the part of the registry for the moment)

  Other ways to free up space...

  SequoiaView
  http://www.win.Tue.nl/SequoiaView/

  JDiskReport
  http://www.jgoodies.com/freeware/JDiskReport/index.html

  Those who can help you discover visually where all space is used.  Then, you can determine what to do.

  After that - you want to check any physical errors and fix everything for efficient access"

  CHKDSK
  How to scan your disks for errors* will take time and a reboot.

  Defragment
  How to defragment your hard drives* will take time

  Cleaning the components of update on your Windows XP computer

  While probably not 100% necessary-, it is probably a good idea at this time to ensure that you continue to get the updates you need.  This will help you ensure that your system update is ready to do it for you.

  Download and run the MSRT tool manually:
  http://www.Microsoft.com/security/malwareremove/default.mspx
  (Ignore the details and download the tool to download and save to your desktop, run it.)

  Reset.

  Download/install the latest program Windows installation (for your operating system):
  (Windows XP 32-bit: WindowsXP-KB942288-v3 - x 86 .exe )
  (Download and save it to your desktop, run it.)

  Reset.

  and...

  Download the latest version of Windows Update (x 86) agent here:
  http://go.Microsoft.com/fwlink/?LinkId=91237
  ... and save it to the root of your C:\ drive. After you register on the root of the C:\ drive, follow these steps:

  Close all Internet Explorer Windows and other applications.

  AutoScan--> RUN and type:
  %SystemDrive%\windowsupdateagent30-x86.exe /WUFORCE
  --> Click OK.

  (If asked, select 'Run'). --> Click on NEXT--> select 'I agree' and click NEXT--> where he completed the installation, click "Finish"...

  Reset.

  Now reset your Windows with this FixIt components update (you * NOT * use the aggressive version):
  How to reset the Windows Update components?

  Reset.

  Now that your system is generally free of malicious software (assuming you have an AntiVirus application), you've cleaned the "additional applications" that could be running and picking up your precious memory and the processor, you have authorized out of valuable and makes disk space as there are no problems with the drive itself and your Windows Update components are updates and should work fine - it is only only one other thing you pouvez wish to make:

  Get and install the hardware device last drivers for your system hardware/system manufacturers support and/or download web site.

  If you want, come back and let us know a bit more information on your system - particularly the brand / model of the system, you have - and maybe someone here can guide you to the place s x of law to this end.  This isn't 100% necessary - but I'd be willing to bet that you would gain some performance and features in making this part.

• Could not start the Windows Vista firewall

  Hi all

  I can't start the Windows Firewall service in anyway.
  I can't open it via Control Panel, as it is said simply: "the Windows Firewall settings cannot poster because the asscioated service is not running. You want to start the Windows Firewall service? »
  I click "Yes", then he said: 'Windows cannot start the Windows Firewall service. There is no error code indicated.
  I tried running "wf.msc" using the Microsoft Management Console. When this window appears, he says: "there was an error opening the Windows Firewall with advanced snap-in security.; The Windows Firewall with Advanced Security snap could not load. Restart the Windows Firewall service on the computer that you are managing. "Error code: 0x6D9.
  As it seems, I can not start it this way or the other.
  I pressed Ctrl + Alt + Delete and click on the Services tab, then click services on the bottom, and this opens the Services window.
  In the new Services window, I try to start the service "Windows Firewall". I get a message saying: "Windows could not start the Windows Firewall service on the Local computer.; Error 1068: the dependency service or group could start. »
  Therefore, it does not. The service is set to automatic.
  I found another process called 'Base filtering engine', which I discovered is related to the use of the Windows Firewall service. Then, that I try to start this service, and he said: "Windows has no start the engine service of filtering based on Local computer." Error 0 x 80320009: an object with this GUID or LUID already exists. »
  Still, I can't find a way to fix the problem. In addition, the service is set to automatic.
  So if someone could help me, give me ideas or tell me how to solve the problem, it would be greatly appreciated. Thanks in advance.
  P. S. sometimes, when I type things in the command prompt, I get a message saying that "the requested operation requires a rise." What it means
  ?
  EDIT:
  The base filtering engine
  IKE and AuthIPsec Keying Modules

  Internet Connection Sharing (ICS)

  IPsec policy agent

  Routing and remote access

  Windows event collector

  Windows Firewall

  All of these services don't work, with each saying "Windows did not start the * service * service on Local computer.; Error 1068: The dependency service or group could start. ", with the exception of the Base Filtering Engine service.

  EDIT:

  I believe that the motor of filter of Bae is the root cause of the problem, because when I try to start it, it says "Windows cannot start the engine service of filtering based on Local computer. Error 0 x 80320009: an object with this GUID or LUID already exists. ", so that all the other programs on this service, said depedent" Windows did not start the * service * service on Local computer. " ; Error 1068: The dependency service or group could start. ».

  EDIT:

  Hello everyone, I solved the problem. The problem is a corrupted, file called "secdrv.sys. To resolve this problem, I had to first download the file "secdrv.sys' out of my operating system CD. To do this, you must create a partition and "mount" a file on CD, on the newly created partition. The file you have to climb is and is called: "*: \sources\install.wim. Extending .wim means a "file system Windows Image" and to see what files it contains, you will need to download what we call the "Windows Automated Installation Kit". Explicit instructions on the installation procedure and where to get this program, is here: "http://www.vistax64.com/tutorials/86959-access-vista-install-dvd-files.html". Once you have the file mounted, just search the area mounted for "secdrv.sys", then copy and paste it in "C:\Windows\System32\drivers" or that where the drivers from your system. After that, restart and the BFE service and all of its dependencies should work properly. Thanks for the good help like SpiritX.

  Hello everyone, I solved the problem. The problem is a corrupted, file called "secdrv.sys. To resolve this problem, I had to first download the file "secdrv.sys' out of my operating system CD. To do this, you must create a partition and "mount" a file on CD, on the newly created partition. The file you have to climb is and is called: "*: \sources\install.wim. Extending .wim means a "file system Windows Image" and to see what files it contains, you will need to download what we call the "Windows Automated Installation Kit". Explicit instructions on the installation procedure and where to get this program, is here: "http://www.vistax64.com/tutorials/86959-access-vista-install-dvd-files.html". Once you have the file mounted, just search the area mounted for "secdrv.sys", then copy and paste it in "C:\Windows\System32\drivers" or that where the drivers from your system. After that, restart and the BFE service and all of its dependencies should work properly. Thanks for the good help like SpiritX.

• Windows Vista: windows could not start error. is suspended from the "Microsoft Corporation" loading bar then black screen BIOS not acpi compliant

  After you have installed the driver for the zune hd, I was asked to restart my computer. After the reboot, start froze on a white screen. I've seen this before and it is usually because of some connected usb components. so I manually powered down the Tower, disconnected the cable from zune and restarted. This time a screen saying that windows could not start, "launch Startup Repair tool" was recommended. Select this habit makes the startup hang to the progress bar from Microsoft corporation, then to a completely white screen. Although strangely, once only a blue error screen appears which says that the BIOS is not acpi compatible. I can't restart with F8 to go into safe mode, "windows error recovery" still appears. "Start windows normally"produces the same results as the tool to restart launch system. " I have a drive to upgrade to windows 7 and a windows XP upgrade disk. the disc of windows 7 hangs at "starting windows" and the XP disc gives a blue screen error: stop: 0x0000007B (0xF78D2524, 0c 0000034, 0 x 00000000, 0 x 00000000)

  I think I have a BIOS problem, but I don't know how I could continue dealing with the repair. I have no success update the bios from usb flash. Any idea is appreciated.
  Update: managed to start with F8, choose to boot in safe mode and loading hangs after "load: \windows\system32\drivers\crcdisk.sys"***.
  the machine is a gateway LX6810-01 (friend motherboard)

  Hello

  1. What is the exact error message when Windows Vista does not start?

  2. you have the disk Installation of Windows Vista operating system?

  I suggest you change the mode of RAMA to IDE in the BIOS. You can contact the PC manufacturer for assistance.

  Note: BIOS change / oxide of additional metal (CMOS) semiconductor parameters incorrectly can causeserious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

   

  In addition, perform a check disk in Windows Recovery Mode.

  (a) Insert the Windows Vista installation disc in the disc drive, and then start the computer.

  (b) press a key when the message "Press any key to boot from CD or DVD".

  (c) select a language, an hour and the currencyand a keyboard or an input method, and then click Next.

  (d) click on check drive for errors.

  (e) in the System Recovery Options dialog box, select the drive of your Windows installation and click Next

  (f) to the System Recovery Options dialog box, click on check Drive for errors.

  (g) use the switch/r to run the disk check.

  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

   

  It will be useful.