crcdisk.sys interruption during the startup of Vista Basic on an E-machine

Similar Questions

• during the installation of Vista Service Pack 2, the computor has been disconnected. Now, I don't have an operating system and startup repair does not work. What should I do now?

  Computor was disconnected during the installation of Vista Service Pack 2. I did now no operating system and startup repair does not work. What should I do now?

  You may have to reinstall Vista from the original media or from the recovery partition according to the type of computer you have.

  Hope that you made the backup recommended all of your data before attempting to install Vista SP2.

• Satellite P305D - different error during the startup sequence

  Hi I have a constant problem I have no idea how fix it. I have Windows Vista Home premium loaded and it works very well when it is running. I can restart the laptop several times and it starts perfectly, if I turn it off for an hour or two and go to start it always happens with a different error during the startup sequence. Most of the time I just go to start Windows normally and it loads, other times I have to go to the ERD.

  I uninstalled Vista and wipe the system well before reloading (using another drive) and the same thing happens. Would it be more likely to be hardware related? I know the battery charges well and I ran all the tools that Vista has to check the hard drive, so I don't know where to go next.

  Any help would be appreciated.

  Terry

  Hello

  Can you please post what errors you get during the boot process?

  In my opinion it could be a hardware problem, because you have already tried to reinstall Vista, so I doubt that the error is software related.
  Strange, but it might be a problem of RAM or HARD disk. The two parties, you can test it with Memtest86 and Drive Fitness Test. Google is your friend to find these two tools.

  In the worst cases, you must go to an authorized service provider. Technicians can check the entire notebook.

• NTOSKRNL.exe problem during the startup of windows xp on a dv5000i Pavilion

  Hi all!

  I have a Pavillion dv5000i

  I get an error message mentioning a NTOSKRNL. Order EXE corrupt during the startup of windows xp.

  I can't boot from a disc XP system either.

  Could this be a HW problem?

  I've extracted the original HD and put it in a usb interface

  I can read it without problem with another PC (so the HD should not be the problem)

  Thank you all

  Kind regards

  Gino

  NTOSKRNL is a software, and it must be there for the machine to start.  The recovery discs should fix this.

• The custom during the Startup logo display

  I'm trying to get a custom logo to display during the startup of a laptop HP Elitebook 450 G1. Can someone send me instructions or link to a utility to do this. Any help will be making thank you.

  ECE

  Your manual

  http://h10032.www1.HP.com/CTG/manual/c03394575.PDF

  F10 Bios Configuration Sytem logo personalized

   

• During the upgrade of vista 64 bit, 7 64 bit process hangs about 2/3 of the way through the last part and I have to reboot that restores Vista.

  7 Windows vista upgrade problem

  During the upgrade of vista 64 bit, 7 64 bit process hangs about 2/3 of the way through the last part and I have to reboot that restores Vista. No idea what could be the cause of the crash?

  Hello

  I suggest you perform the steps in troubleshooting from the following link and check how it works.

  Upgrade stops responding (hangs) at 62% when you upgrade to Windows 7

  Check out the following link for more information about how to upgrade Windows Vista to Windows 7

  Upgrade Windows Vista to Windows 7

• I understand that the watch ntbtlog.txt file drivers loaded during the startup process. I'm worried when it shows driver loaded, but it is not a list.

  I understand that the watch ntbtlog.txt file drivers loaded during the startup process. I'm worried when it shows driver loaded, but it is not a list. Why is this?

  Hello

  Yes, it can be in hidden files that may cause by the virus.

  I also suggest you to see link and check.

  Show hidden files

  http://Windows.Microsoft.com/en-us/Windows7/show-hidden-files

• Cisco Aironet 1262N stuck during the startup process

  I'm banging my head against the wall, trying to figure out why my AIR-AP1262N-A-K9 will start all the way. He'll get all the way to initiate interfaces and stop. I can never get to control the CLI. This is my first time with a cisco ap but everything I read it very easy sewing.

  This unit from what I understand will work on its own with no controller. Therefore, it is called a "stand-alone" model Yet he seems to be looking for something to complete during the boot. Below the out put for starting. The last line is where it stops.

  If anyone can help me I would be very happy.

  WRDTR, CLKTR r: 0x8200083f 0x40000000
  r RQDC, RFDC: 0 x 80000033 0 x 00000212

  using the values from the eeprom

  WRDTR, CLKTR: 0X8200083F 0X40000000
  RQDC, RFDC: 0 X 80000033 0 X 00000212

  MCNG ddr static values of the eeprom series
  init done DDR

  IOS Bootloader - start System.
  Flash CHIP: Numonyx P33
  Check for more deleted blocks
  ................................................................................
  ................................................................................
  ................................................................................
  ......
  XMODEM file system is available.

  DDR used values of the system serial eeprom.
  WRDTR, CLKTR: 0X8200083F, 0X40000000
  RQDC, RFDC: 0 X 80000033, 0 X 00000212

  PCIE0: the connection is established.
  PCIE0: VC0 is active
  PCIE1: the connection is established.
  PCIE1: VC0 is active
  PCIE 64-bit devices
  PCIEx: initialization done
  flashfs [0]: 147 files, 7 folders
  flashfs [0]: 0 orphaned files, orphaned directories 0
  flashfs [0]: Total number of bytes: 31739904
  flashfs [0]: bytes used: 6435328
  flashfs [0]: available bytes: 25304576
  flashfs [0]: flashfs fsck took 9 seconds.
  The system eeprom read cookie series... Fact
  MAC Ethernet address of base: 7 c: ad: 74:93:36:ba
  Waiting for auto-negotiation complete PHY... TIME-OUT!
  Ethernet link is down.
  Error: Speed RGMII

  The system has encountered an error during initialization
  the Ethernet port.
  The system is ignoring the error and continue to start.
  If you stop the system startup process, what follows
  orders will be re - initialize Ethernet, TFTP and finishing
  loading the operating system software:

  ether_init
  tftp_init
  boot

  for 22 seconds
  process_config_recovery: set the IP address and the default config 10.0.0.1
  process_config_recovery: image recovery

  PA:
  WRDTR, CLKTR r: 0x8200083f 0x40000000
  r RQDC, RFDC: 0 x 80000033 0 x 00000212

  using the values from the eeprom

  WRDTR, CLKTR: 0X8200083F 0X40000000
  RQDC, RFDC: 0 X 80000033 0 X 00000212

  MCNG ddr static values of the eeprom series
  init done DDR

  Normal running Memtest...
  Past.
  IOS Bootloader - start System.
  Flash CHIP: Numonyx P33
  Check for more deleted blocks
  ................................................................................
  ................................................................................
  ................................................................................
  ......
  XMODEM file system is available.

  DDR used values of the system serial eeprom.
  WRDTR, CLKTR: 0X8200083F, 0X40000000
  RQDC, RFDC: 0 X 80000033, 0 X 00000212

  PCIE0: the connection is established.
  PCIE0: VC0 is active
  PCIE1: the connection is established.
  PCIE1: VC0 is active
  PCIE 64-bit devices
  PCIEx: initialization done
  flashfs [0]: 147 files, 7 folders
  flashfs [0]: 0 orphaned files, orphaned directories 0
  flashfs [0]: Total number of bytes: 31739904
  flashfs [0]: bytes used: 6435328
  flashfs [0]: available bytes: 25304576
  flashfs [0]: flashfs fsck took 9 seconds.
  The system eeprom read cookie series... Fact
  MAC Ethernet address of base: 7 c: ad: 74:93:36:ba
  Waiting for auto-negotiation complete PHY... TIME-OUT!
  Ethernet link is down.
  Error: Speed RGMII

  The system has encountered an error during initialization
  the Ethernet port.
  The system is ignoring the error and continue to start.
  If you stop the system startup process, what follows
  orders will be re - initialize Ethernet, TFTP and finishing
  loading the operating system software:

  ether_init
  tftp_init
  boot

  "Loading Flash:/ap3g1-k9w7-mx.124-25d.JA1/ap3g1-k9w7-mx.124-25d.JA1"...### ".
  ################################################################################
  ################################################################################
  ################################################################################
  ################################################################################
  ################################################################################
  ###############################################################################

  File "flash:/ap3g1-k9w7-mx.124-25d.JA1/ap3g1-k9w7-mx.124-25d.JA1" uncompressed one
  ND installed, point of entry: 0x4000
  execution of...
  ENET stopped

  Legend restricted rights

  Use, duplication, or disclosure by the Government is
  subject to such restrictions as set out in paragraph
  (c) Commercial - limited computer software
  The rights to FAR clause 52.227 - 19 and subparagraph s
  (c) (1) (ii) rights to technical and computer data
  Clause of DFARS 252.227 - 7013 section software.

  Cisco Systems, Inc.
  170 West Tasman Drive
  San Jose, California 95134-1706

  Software Cisco IOS, C1260 Software (AP3G1-K9W7-M), Version 12.4 (25 d) JA1, COMMUNICATED
  SOFTWARE (fc1)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2011 by Cisco Systems, Inc.
  Updated Friday, August 11, 11 02:07 by prod_rel_team

  Proceed with the initialization of the system

  Proceeding to unmask interrupts
  Initialization of flashfs...
  Flash CHIP: Numonyx P33
  Check for more deleted blocks
  ................................................................................
  ................................................................................
  ................................................................................
  ......

  flashfs [1]: 147 files, 7 folders
  flashfs [1]: 0 orphaned files, orphaned directories 0
  flashfs [1]: Total number of bytes: 31481856
  flashfs [1]: bytes used: 6435328
  flashfs [1]: available bytes: 25046528
  flashfs [1]: flashfs fsck took 7 seconds.
  flashfs [1]: initialization complete.
  flashfs [2]: 0 files, directories 1
  flashfs [2]: 0 orphaned files, orphaned directories 0
  flashfs [2]: Total number of bytes: 11999232
  flashfs [2]: used bytes: 1024
  flashfs [2]: available bytes: 11998208
  flashfs [2]: fsck flashfs took 1 seconds.
  flashfs [2]: initialization complete... done Initializing flashfs.

  Radio0 presents 8364B 8000 B8020000 0 B8030000 10
  Present Radio1 8364B 8000 B0020000 0 B0030000 C
  Waiting for auto-negotiation complete PHY... TIME-OUT!
  Ethernet link is down.

  This product contains cryptographic features and is under the United States
  States and local laws governing the import, export, transfer and
  use. Delivery of Cisco cryptographic products does not imply
  third party approval to import, export, distribute or use encryption.
  Importers, exporters, distributors and users are responsible for
  compliance with U.S. laws and local countries. By using this product you
  agree to comply with the regulations and laws in force. If you are unable
  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:
  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at
  [email protected] / * /.

  processor of Cisco AIR-AP1262N-A-K9 (PowerPC460exr) (revision B0) with 81910 K/4
  9152K bytes of memory.
  Card processor ID FTX1716E2DN
  PowerPC460exr CPU 666 Mhz, the 0x18A8 revision number
  Last reset of tension
  1 gigabit Ethernet interface
  2 802.11 radios

  32K bytes memory simulated by flash not volatile configuration.
  Basic Ethernet MAC address: 7 c: AD:74:93:36:BA
  Part number: 73-12175-06
  Kit numbered PCA: 800-32268-06
  Revision number of PCA: B0
  Serial number of PCB: FOC17106662
  Top Assembly part number: 800-33866-02
  Top of page the Assembly serial number: FTX1716E2DN
  Top of page revision number: A0
  Product/model number: AIR-AP1262N-A-K9

  Press RETURN to get started!

  * 00:00:09.481 Mar 1: % SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: crypto IOS FIPS t auto
  is spent
  * 00:00:09.490 Mar 1: * CRASH_LOG = YES

  * 00:00:09.490 Mar 1: PCIE 64-bit devices
  * 1 Mar 00:00:09.789: soap_extern_intr_dispatch: no handler for UIC2 intrno 12 l
  n level 4
  * 1 Mar 00:00:10.088: soap_extern_intr_dispatch: no handler for UIC2 intrno 12 l
  n level 4
  * 00:00:12.966 Mar 1: % SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: crypto RADIO FIPS auto
  test successful Dot11Radio interface 0
  * 00:00:15.649 Mar 1: % SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: crypto RADIO FIPS auto
  test successful 1Base Dot11Radio interface Ethernet MAC address: 7 c: AD:74:93:36:
  BA

  * 00:00:56.377 Mar 1: % LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
  up to
  up to
  ernet0, changed state down
  * 00:11:00.003 Mar 1: % LINK-5-CHANGED: Interface Dot11Radio1, changed state of a
  dministratively down
  * 00:11:00.003 Mar 1: % LINK-5-CHANGED: Interface Dot11Radio0, changed state of a
  dministratively down
  * 00:11:00.003 Mar 1: % CDP_PD-4-POWER_OK: full power - AC_ADAPTOR inline power s
  ource
  * 00:11:00.012 Mar 1: % SYS-5-RESTART: System restarted.
  Software Cisco IOS, C1260 Software (AP3G1-K9W7-M), Version 12.4 (25 d) JA1, COMMUNICATED
  SOFTWARE (fc1)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2011 by Cisco Systems, Inc.
  Updated Friday, August 11, 11 02:07 by prod_rel_team
  * 00:11:00.012 Mar 1: % SNMP-5-start COLD: SNMP agent on host ap undergoes a c
  old beginning
  * 00:11:00.994 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
  State of GED until
  * 00:11:01.003 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
  1, changed down state
  * 00:11:01.003 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
  0, changed down state
  * 00:11:11.956 Mar 1: % LINK-3-UPDOWN: Interface BVI1, changed State to down
  * 00:11:12.957 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
  State of GOL downstairs

  What are your settings of the nec console?

  You must be 9600, none, 8, 1 and flow controll set off to be able to interact with the CLI

  HTH,
  Steve

  ------------------------------------------------------------------------------------------------
  Please don't forget to rate helpful messages and mark the questions answers

• "Windows could not update the configuration to start the computer" error during the upgrade of Vista in Windows XP

  I have a laptop Dell Inspiron 1505, that is running Windows XP Media Center Sp3. I'm doing a place in upgrading to Vista since the disks to upgrade Dell... Everything's fine until the 'Expansion of the files' [27%], then the installation fails with this message: "Windows could not update the configuration to start the computer. Installation cannot continue. Any changes made to your computer during the upgrade". I did a google search for a fix that involves changing a value in the registry in the HKLM\SYSTEM\CurrentControlSet\Control\Class\ {4D36E976-E325-11CE-BFC1-08002BE10318} for example change the value to PartMgr Upperfilters. Unfortunately, this value was the default for my registry key changes could be made. Some other fixes involved the renaming of Upperfilter.bak, for Upperfilters unfortunately this .bak value does not exist in my registry.

  I tried to boot from the disk of Vista and changing the msconfig for a selective startup but without result.

  In addition, the stall even appears at a similar point when you try to upgrade to Windows 7. Is it because of the presence of hidden Media Direct and Dell restore partitions? Compatibility Assistant programs for the two operating systems found nothing significant. Anti virus has been disabled during the installation procedure. Any help will be greatly appreciated. Thank you.

  Hello

  Not quite, but pretty close. Media Direct could not lock the boot sector. It must be a BIOS lock or a mechanism of protection provided by your antivirus software.  Given that, I would check your program settings then for all that prevents changes to the boot sector. You may find more easy just uninstall it and reinstall it after the upgrade. Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• How to select a different language during the installation of Vista on Satellite L30?

  At the start of the toshiba L30 first running windows vista basic in Dutch has been selected by mistake. The vista has been installed. I tried to format PC and reinstall windows vista basic to the General again, but it would still allow me select the English operating system.

  Unfortunately, it was a mistake, and I don't understand Dutch. Is thereany way I can reinstall the operating system in English. ?

  E-mail: [email protected]
  Thank you

  Matthew

  Hello Matthew

  Do you use any recovery DVDs delivered for installation of the OS? where you bought your laptop (country)?

• Qosmio G30-153: no drivers were found during the installation of Vista

  Hi I tried to install Vista on my computer, but there are some bad things. I just insert the Vista CD and restart my machine.

  Vista has started to install and I have reached the point where Vista should find the drivers to choose, but its tells me no drivers were found.

  I took it to the Agency in Syria and they told me that this (Qosmio G30-153) machine comes with vista only.
  If you have upgraded from XP applies to the Qosmio only.

  I think there is another problem, but they could not solve it because I told them when I go to the configuration of the system, I found the drivers, but the names are different.
  Driver (C) named Raid 0, but the names of the drivers D Jbod and I think they should be eponymous.

  If they are different name, but they don know what I mean.
  do you know how to change the name of the pilots and why they are different.

  I hope you can help me and I will answer you on my email address if you don't mind my ([email protected]) is

  Thanks alotttttttt Byeeeeeeeeeeeeeeeee

  Here is no problem at all. Visit the Toshiba support under http://eu.computers.toshiba-europe.com page

  You will find RAID driver. Please download this driver and use it for the installation of the OS. Unmanned RAID HDD is not visible, but after the hard disks in RAID driver loading will be visible and you can continue the installation of the OS. RAID driver can be saved to USB.

  If you have any other questions, please write again.

  Bye and good luck!

• During the installation of Vista SP2 (KB948465) on a laptop, I get error code 800F082C.

  There is very little information on the Internet for this error code. The OS is Vista Ultimate on a Dell Precision laptop. The machine is a member of a domain AD running on SBS2008.

  Hi Homechicken,

  Welcome to Microsoft Vista answers Forum!

  Download and run (Checksur.exe) system update readiness tool. After downloading this tool, it runs an ad hoc analysis of inconsistencies that might prevent future maintenance operations.

  For more information about how to download and run the system update readiness tool, click on the number below to view the article in the Microsoft Knowledge Base: 947821 Description of the System Update Readiness Tool for Windows

  Vista and Windows Server 2008: http://support.microsoft.com/default.aspx/kb/947821

  No matter what field of issues; I suggest you contact the TechNet forum for further assistance. Please visit the link below to find a community that will provide the best support.

  http://social.technet.Microsoft.com/forums/en-us/category/windowsvistaitpro

  Hope this information is useful.
  Let me know if it worked.
  All the best!

  Thank you, and in what concerns:
  Swathi B - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows XP Pro can't find HD during the startup of the CD process.

  Lately, when my computer starts, it began to automatically run the disk check process. During the process, several files are either deleted or recovered. It's embarrassing so I tried to repair Windows XP Pro OS. The problem is that Windows does not detect the drives. I tried the ASR system, the R option to repair, and continues even with the start of the CD but Windows reports it cannot locate my hard drives. My motherboard is GA-81955 X Royal Gigibyte with 2 IDE hard drives of 40G and 2 DVD/CD players. Thanks for any help.

  The problem is in the AVG Antivirus software that I had to uninstall and remove all references to it in the registry. With no antivirus on the computer software, everything worked fine.

  Then, recently, there was an automatic update of Windows that enamored System32 of the computer records. Due the Gigibyte motherboard and how second HDD and DVD/CD player were to be installed to operate Windows has not found any drive C.

  To get the C drive to work again I had to remove it and install it in another computer as a slave drive XP then manually restore the files of System32. The restored files are not the same that have caused other problems. I tried to reinstall only the C drive and 1 DVD/CD drive but windows still not able to perform automatic recovery. Spent several weeks to correct the problems and reinstalling the software.

  The best solution would have been to reformat the C drive and reinstall the software, but I didn't know if I had backed up all my data.

• Windows 10 gives an error during the startup screen

  New installation of Windows on a laptop Lenovo B50 10 - 30, all drivers updated.

  Adobe Photoshop Lightroom 6 installation ends without errors, but when I run Lightroom an error message appears during the boot screen, saying: «Adobe Photoshop Lightroom 6 stopped working...» ». The only option at this point is to close the application.

  What should do? Thank you!
  

  The failing application path: C:\Program Files\Adobe\Adobe Lightroom\lightroom.exe

  Path of the failing module: C:\WINDOWS\SYSTEM32\ig7icd64.dll

  Report ID: cceda8ca-0de5-48b0-95d3-5d2aed59f4a6

  Cause of the crash is your graph card C:\WINDOWS\SYSTEM32\ig7icd64. DLL

  Update your graphics card as one of its defective module crashes Lightroom

  To confirm this:-open Device Manager > display adapters > right click on your graphics card

  Select Disable

  Starting Lightroom

  Let us know if this helps

  Assani

• Blue screen during the startup or shutdown

  I have windows vista home premium.sometimes during startup or during shutdown, a blue screen appears for a very short time and the restarts.from of the computer, what I have seen during this short period his written dumping physical memory, etc as something is written on my BIOS.do I need to update my BIOS version or is there any other problem? Please answer soon.thanks.

  You can download the contents of the c:\windows\minidump on SkyDrive and provide a link?

  Consider the following general guidelines for dealing with bluescreens.

  Consider running chkdsk on all partitions.  Leave complete chkdsk on each partition and see if that helps.

  Also consider running SFC/scannow.

  If you start in safe mode, do you still feel bugs? What if you do a clean boot, or boot device?

  Consider the memory with memtest86 or Windows Memory Diagnostic test. Note that memory that pass the tests isn't necessarily good memory - he not only failed a review.  Examine systematically to eliminate the system RAM - run with a few modules for awhile and see how things are going. Then try the other modules.

  Other common suggestions include ensuring drivers are up to date, but also to ensure that you use the latest version of the BIOS.

  It may be useful to use the driver verifier.  To activate the... Driver Verifier start-> verifier.exe-> OK-> create standard settings-> next-> driver select the names to a list-> next-> sort by provider-> select all other Microsoft drivers-> finish and OK your way out of the dialog box.

  Then restart and use the system as you normally and wait for a problem.  In case the system does not completely start after activation of the Verifier, boot mode safe and run driver verifier and tell him to remove the changes.

  Wait for a bugcheck occurs after you have enabled the auditor as described, and then download the dump on your SkyDrive and provide a link.