cRIO-9024 - supports SSH (Secure Shell) network?

Similar Questions

• Choose the network protocol for CRIO-9024 to PXI on Ethernet

  We are in the design phase, implementation of an embedded controller for CRIO-9024 to send data captured at an SMU-8105 on ethernet controller. The data will be arrays of double-precision 2D. These data should be sent to the pxi at the end of each test step. Each stage will have a different number of channels and sampling frequencies.

  For example, Test step 1 will have 5 channels of analog inputs that will be sampled to 100,000 KHz for 1 second. These data will come from the CRIO FPGA. Data will be get dealt with by the CRIO-9024 and analyzed post to pass or not not metric. Then, the CRIO controller will send the data 2D (data points 500 000 5 X 100 000) table and the results of all the measures (a table 1 d) for PXI.

  The connection with the PXI will use Ethernet.

  Do not forget that the PXI should also send the CRIO certain values to tell the CRIO when starting the test, and when the test sequence is completed.

  I thought that TCP/IP would work better because of communication 2-way necessary. But then I was watching streaming network or even using shared Variables.

  If anyone has any ideas or suggestions please please post them.

  Hello

  You can use either.  If you are more comfortable with really.  The STM method will be a little less overhead on my style XML tagging data, but it will be very short given the size of the data.  Probably go with STM has it right most of the work for you.

  Regarding the size data the you must normally transfer data as this is to flatten to a string.  If you convert a string of numbers readable human you will either lose accuracy, increase the size or both.  Because the string after that flattened will be the same size as the original array anyway for the quick calculation based on your previous post 500 000 double (8-byte) is 4 miB (3.8 MB)

  See you soon,.

• HP Deskjet 3050 - unable to connect to the WPA secure wireless network

  Hello

  My first post here so please excuse any misstep on my part.  I bought this HP Deskjet 3050 a week ago and have since been war with it.  I would be really grateful if someone could possibly give advice on how I can solve this problem.

  I am unable to connect the printer to my secure wireless network, even if the other computers, cell phones, etc. are connected without problem.  I tried WPA, WPA2 and WPA2-Mixed modes with the same failure security. Specifically, the 66% reached Connection Wizard, then displays the error that the wizard can not find/network printer.  If I disable the security, the printer connects very well.

  I use a Linksys WRVS4400N router with firewall and associated firewall disabled settings.  The router broadcasts on 802. 11 g / N mixed mode.

  I install the software provided on the CD for installation on a Windows XP SP3 System.  I confirmed that the PC and the printer are connected to the network are the same.

  The issue as well, if you will allow me: I have not yet tried these drivers, but I see there are any updated drivers for the printer in date from 14/12/2010.  The release notes indicate the improvement of networks, but do not develop beyond that.  Does anyone know if there was a known problem with the connection to secure networks that has now been corrected?

  Finally, just a note that I am partially blind and using a screen on all systems reader.  I'll try my best to be as helpful as I can to please forgive me if I can't find the settings, etc. on screen and sometimes need help for a little more detail.

  Thanks in advance for your help, I really enjoyed.

  Have a nice day,

  All the best for now and take care,

  Hussein.

  It is not the fact that it is impossible, is the fact that this was not done, yet.

  Hello

  first of all, my apologies for the delay getting back to you.  Poor health means that I had little time or want to do great thing on the side of the computer of htings.

  In any case, I am please to say the problem with the HP 3050 failing to connect to my network is now resolved.  There seems to be a bug with the installer, and that seems to include the version the most recent publication Dec 2010.

  To resolve this problem, I did the following:
  1. disable all security for the network options, so it's just an open network.
  2. connect the HP 3050 to the network by using the installation wizard. This time it connected OK for me.
  3. Locate the IP address of the printer.  I used the table of customer list accessed by my router interface. You may be able to get this through the printer on the menu screen, but as I am partially blind, it wasn't an option for me.
  4. Enter the control panel of the printer to http://ip.address.of.printer for example http://192.168.2.108
  5. under Advanced options, configure the network settings, including the password and the Security Protocol.  Don't forget to enter the SSID of the network exactly as it is configured on the router.
  6. apply settings, disconnect from the control panel of the printer.
  7 log in the router configuration panel and re-apply the security options.  Make sure they match these match those entered for the printer.

  I hope it will be useful to others in the same position.

  Thanks again for your time.

  Best,

  H.

• wireless network unsecured wireless (WPA2) secure verses network

  I can't connect to the internet using the secure wireless network, but I can using an unsecured wireless network is there a setting I need to change?

  Hi lylelm,

  In addition to valuable suggestions provided by PML, you can have a look at this article as well.

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  (May also be tried for Windows XP SP3)

  I hope this helps.

• Support for devices on network HP service does not start

  Product: HP Photosmart Premium all-in-one (C309g)

  OS: Vista Business 32-bit

  Errors:

  When running the part 'Add a device' overall upward to add the printer to my PC, so it can be accessed without thread that appears in the background: "the specified service does not exist as an installed service."

  The result of the above process is the following message is displayed in the installation of HP screen: "the HP software that allows networking is not responding. Cancel the installation and then restart the PC. »

  As you can guess, I had this printer for some time a couple / few years at least and I did turn it wireleslly for some time.

  The printer is active on my wireless network, print the printer wireless network Test report proves. I can also access the printer Web page by entering its IP address in a web browser.

  We perceived first of all the question when the HP Solution Center reported that the printer is connected is no longer. And he suggested to do something with the installation, which sent me down the road to unintalls and installs.

  I ran printing HP and the Scan doctor, who tells me that the printer is installed for use via the USB port, but the instance networking is not installed.

  I still have the original installation CD for this printer. Run the installation off the coast of the root of the CD, I get the 'latest Version already installed"or something to that extent.  I also downloaded the latest Basic and full functionality installed on HP site.

  I used Revo Uninstaller to my uninstall and I ran CCleaner once all applications have increased from the list of programs.

  I read somewhere that it is related to the "HP network devices Support" service

  In computer management, I see that its not working do not and it is configured to start "automatically (delayed start)".

  When I try to start the service I get this: "Windows could not start the service of supported devices in HP Network on the computer local error 2: they system could not find the specified file.

  Somethings that have been made on this machine recently, I don't know when the problem of the printer started...

  Installed Quicken 2013

  ITunes installed

  Changed my home network from the Public to the private sector on this machine so I could implement the media servers.

  I check through all files updated my antivirus quarantined and it doesn't seem to be HP files in there.

  I hope my question is in fact this service, and somehow replace the missing his refferencing file will fix this.

  My next step is to uninstall once again and make sure that service falls off the list too, then reinstall HP DOWNLOAD.

  I suggest using the scrubber software integrated into the installation of clean up. The steps below will guide you through it.  Before step 10 from a CD or step 15 leave a download, check the two program folder files to make sure that the HP files are deleted.

  Of the original printer installation CD:

  1. Insert the CD in the drive and then cancel Setup

  2. open my computer and click right then on the CD from the drive and select open

  3 open the Util folder

  4 open the CCC folder

  5. run the L4.bat uninstall_ for computers not HP.  For HP computers, run the Uninstall_L3.bat

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9. use this tool to clean the registry.  Note: This utility is not HP sponsored or approved.  HP and I are not responsible for damage or loss of data caused by the utility.  This step is optional.   You can skip if you want.

  http://download.CNET.com/advanced-SystemCare/3000-2086_4-10407614.HTML?part=DL-6271865&Subj=DL&tag=button

  10 download the drivers and full software features

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-73652-3&cc=us&DLC=en&LC=en&OS=2093&product=3793676&sw_lang=

  11 start the download to reinstall the printer

  Starting a download:

  1. run the disk cleanup on your computer

  2. download and run the software and the drivers below.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-73652-3&cc=us&DLC=en&LC=en&OS=2093&product=3793676&sw_lang=

  3. once the download is done retrieve, cancel the download.

  4. click on the start menu.

  5. click on run.

  6. type %temp% enforcement

  7. Locate and open the folder starting with 7z (example: 7zS2356)

  8 open the Util folder

  9 open the CCC folder

  10. run the L4.bat uninstall_ for computers not HP.  For HP computers, run the Uninstall_L3.bat

  11. once the uninstall is complete, restart the computer

  12 run the Accessories\ System Tools Disk Cleanup

  13. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  14 use this tool to clean the system and the registry.  Note: This utility is not HP sponsored or approved.  HP and I are not responsible for damage or loss of data caused by the utility.  This step is optional.   You can skip if you want.

  http://download.CNET.com/advanced-SystemCare/3000-2086_4-10407614.HTML?part=DL-6271865&Subj=DL&tag=button

  15 download the drivers and full software features

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-73652-3&cc=us&DLC=en&LC=en&OS=2093&product=3793676&sw_lang=

  16. run the download to reinstall the printer

• How to secure wireless network with a computer running XP and one running Vista

  When I secure my network wireless on my desktop (XP) I can not connect to internet on my laptop which is running Vista.    I use "WPA Personal" as my security mode on my desktop.

  I've seen variations of this question, but not exact, so I'm still at a loss.

  Hello

  Follow the steps in this link-

  http://forums.Afterdawn.com/thread_view.cfm/678319

  If you have created a network profile, then delete it and create a new you follow these steps.

• iOS image support ssh

  Hello dear

  Please can you tell me the image ((c2960-lanbase - mz.122 - 53.SE1.bin)) support the ssh or not?

  If not what ios image can I charge for the 2960 G switch to support ssh.

  Thank you

  Hello sajjad_m1987,

  C2960-lanbase - mz.122 - 53.SE1.bin does not support ssh.

  You will need the crypto image that has the k9 in the name.

  C2960-lanbasek9 - mz.122 - 52.SE.bin

  You can go to the following link to search the ios which supports the functionality that is necessary.

  http://Tools.Cisco.com/ITDIT/CFN/JSP/by-feature-technology.jsp

  Hope this helps,

  If Yes, please rate.

• Module SSL are supported SSH version 1?

  Hi all

  I am pleased that we have this great to discuss Cisco product forum.

  We have a SSL Module installed in our Catalyst 6509. The problem is what SMLS can only support SSH version 1, I could not find how to activate SSH version 2. Is it possible to use SSh version 2 for this device, only that I have to update the IOS?

  Thank you very much for the help!

  Details in the following way:

  SSLM_SLOT9 (config) #ip ssh?

  new authentication attempts to specify number of authentication retries

  Departure (or only) Port number to listen on the port

  RSA RSA key pair name configure ssh

  source-interface interface to specify to address SSH source

  connections

  timeout specify SSH timeout

  SSLM_SLOT9 (config) #ip ssh version 2

  ^

  Invalid entry % detected at ' ^' marker.

  Here is the information for the device:

  Cisco Internetwork Operating System software

  IOS (TM) SVCSSL (SVCSSL-K9Y9-M), Version 12.2 YS VERSION SOFTWARE (15)

  Copyright (c) 1986-2004 by cisco Systems, Inc.

  Last updated on Saturday, 28 May 04 17:29 by integ

  Image text-base: 0 x 00400078, database: 0x00AFE000

  ROM: System Bootstrap, Version 12.2 YS1 SOFTWARE (11)

  SSL Module WS-SVC-SSL-1

  HW Fw (1) Sw 2.1 7.2 3.2 (2).

  Hello

  support for SSHv2 has been added in version 3.1 software SMLS:

  http://www.Cisco.com/en/us/partner/docs/interfaces_modules/services_modules/SSL/3.1/release/notes/ol_9138.html#wp201055

  HTH

  Herbert

• ASA - SSM support SSH V2?

  I'm starting to implement the CRA and tried to get the key of the host of the ASA - 5520 it got an error without papers:

  IPS (config) # ssh - host key 10.0.0.50

  Error: getHostSshKey: no supported version of remote Protocol (2.0)

  Can it be true that the IPS does not support SSH V2?

  Unfortunately, despite the underlying Linux system support SSH versions 1 and 2, the part IDS/IPS is not at the moment. There is a request for existing value/functionality (CSCse05771) for the addition of this type of support

  HTH

• Deployment of VeriStand model to cRIO-9024

  Hello

  I am trying to deploy a dll of Veristand simulink to my target RT VxWorks cRIO model 9024 but I get error compatibility while deploying, saying:...

  Specified model is not supported in the current execution target!

  I created the DLL file and output using RT workshop and placed them in the same folder.

  Can someone help me please?

  Check the XML in your .fpgaconfig and make sure that the values returned by your module HAVE matches the configuration fixed-point.  Looks like your values are currently set to scale by a factor of 16, what could happen if your whole word length is off by 4.  Also make sure you have all the scale applied for channels to HAVE it.

• Support of security Norton advise me I require no security on the iPad for purchases online as Apple coverage, this. Is that correct. Thank you.

  Norton security advice I don't need Norton security for online shoppin and Apple covers this. Is this correct?

  Thank you

  Currently, there are no viruses that affect the iOS devices. As long as you only buy from reputable sites, you should be fine. You should consider your shopping while using a known and trusted WiFi network (or cellular data if your iPad). The public WiFi networks can be a problem.  No technology don't protect you if you give your information to a person not worthy of trust.

• Frequent disconnects between cRIO-9024 and host computer

  Hi all

  I had a brand new cRiO OR 9024 and several modules of recording data a few days ago. I have setup the IP address for the cRIO which is 10.0.0.2 and the subnet mask is 255.255.0.0, which is the same with what I've done for the host (different IP address). I installed the software that I need on the controller RT. Throughout the process, I have disabled the firewall. I use MAX 5.0 and NEITHER cRIO 4.0. Two of them are the latest version. I built the link between the cRIO and my computer successfully. However, the target is always disconnected from the host computer, even if I do not have action on the cRIO, that is. Without running any software on it. Status of the disconnection is achieved since the MAX, but surprisingly, I can ping through the IP address of the cRIO. It seems to me that the connection between the host computer and the cRIO was established.

  I tried to run code on the target, but unfortunately, the disconnection also occurs frequently simple. I checked the CPU target and the use of memory, which are low. So I concluded that the disconnection is not generated by the high utilization of the processor or memory.

  I also tried to reformat the cRIO and reinstall all software, but it has no effect.

  I also found that a warning appears regularly on MAX interface that "there was a problem to retrieve the settings of the target. For more information, go to ni.com/frinfo and enter the Info Code MAXServerUnkownError. If the problem persists, contact National Instruments'. I checked MAXServerUnkownError of

  NI.com and followed the instructions to make sure that there is no bad configuration on my computer as a firewall etc. However, without doing wrong was found.

  Can someone help me figure out what is the problem?

  Concerning

  Japanese

  Hello Japanese,

  Thank you for answering my questions. I have more questions that should lead to a solution to your problems:

  1 is the add-on NO-time installed on the cRIO?

  2. are you able to disable the antivirus on your computer?

  The add-on NO-time turns out to cause frequent disconnects with cRIOs in LabVIEW 2011. To view the add-on, you will need to right click on software under the cRIO, select Add/Remove Programsand select the option custom software installation . If it is installed, I recommend to remove this add-on the cRIO to help solve disconnects.

  Please let me know if disconnects continue after removing NO-time and disabling the antivirus.

  Kind regards

  Andrew Brown

• Pro-grammatically discover remote devices (cRIO or sbRIO) within the Local network

  Hi I'm developing an application where I need to configure my cRIOs. So first of all, I need to find out all the RIO within the network and configure one by one by selecting their IP address in the list.

  What someone has to know everything how to discover. I think there must be a solution that MAX discover any type of remote devices.

  Help, please.

  You specify the version of LabVIEW you use. In LabVIEW 2009, you can use the RT to target information VI for a list of all targets of RT on your local subnet.

  

• Why do I get error-65581 when you try to use a cRIO 9024 and modules c series

  I am trying to send a digital high on a 9401 c series module DIO0 and I get the following error every time.

  65581 error occurred in shared Variable to send true value Out.vi

  NMAYO,

  Depending on your project can you right click on the chassis in the cRIO and make sure that it is set to the Mode Scan mode and not FPGA? In addition, in the solution of measurement and Automation Explorer, you can check the cRIO and check that it has the Support of Scan Engine is installed. The tutorial below shows how to reformat a cRIO and install the software on this subject, the subsequent steps in the software allow you to check your cRIO.

  Reformat a controller embedded time real CompactRIO

• cRIO-9074 to PC connection. (connectivity network limited or not)

  Hello.

  Today, I tried to connect a cRIO 9074 to my laptop.

  But MAX could not see it.

  Then I discovered that the laptop Ethernet driver was not installed. After I installed the new driver network connection appears in the status bar, but he signed limited connectivity or not.

  In addition, when I check its status as the IP address is not 0.0.0.0 even when IP Reset DIP-switch is activated.

  What can be the problem and how can I solve it?

  Thank you!

  Yes, to use the cRIO, you need the following:

  LabVIEW

  LabVIEW Real-time

  NEITHER RIO driver

  LabVIEW FPGA (Optional if you use the scan Mode)

  See "Getting Started with Compact RIO" like a good guides through all your first steps.