Crypto can be applied by entering ethernet interface.

Similar Questions

• How can I put wireless and ethernet interfaces together?

  I have a 877w router, and I'm trying to set up a wireless network.

  I have a bridged RFC1483 ADSL, so I ATM0.1 in a group of bridge, and then, I defined an interface BVI1.

  However, after you have configured the wireless interface, I noticed that my laptop is the IP address of the supplier, as if wireless had precedence on the BVI interface. Put the Dot11 interface in a separate bridge under VLAN1 does not seem to help either. I tried to put everything in the same bridge, but fast ethernet interfaces do not support address (how the British Virgin Islands work then, I wonder).

  What should I do? Use two VLANS separated? I wouldn't do that. Any help appreciated. Thank you

  Hey, thank you, that did it.

  So I followed the article. I guess I don't understand how the British Virgin Islands. Of the article, I thought them then were at the same level, i.e. all the right behind the ATM interface. I also thought that a BVI able to fill several VLANS. Now my next mission is to understand why I was wrong on both counts.

  Guys, thank you very much for the help. Now I'll try to better understand what I :-)

• Can not connect - when entering a password message "the service user profile service has no logon. Failed to load profile \User' cannot access start menu to apply the options.

  Can not connect - when entering a password message "the service user profile service has no logon. Failed to load profile \User' cannot access start menu to apply the options.

  Hello

  1st thing to try is the system in safe mode restore to before the problem

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not solve it read more

  read the tutorial below

  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  When you log on a Windows Vista-based or a Windows 7 computer by using a temporary profile, you receive the following error message:

  The user profile Service has not logon. User profile cannot be loaded.

  http://support.Microsoft.com/kb/947215#letmefixit

  Your user profile was not loaded correctly! You have been logged on with a temporary profile.

  http://support.Microsoft.com/kb/947242

  If you tried to log on to Windows and received an error message telling you that your user profile is damaged, you can try to fix it. You will need to create a new profile and then copy the files from the existing to the new profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

• How can I create a user of single player?  I tried with roles of readers, but I have to enter Advance Interface.

  I tried with roles of readers, but I have to enter Advance Interface with this user.

  This article: http://www.ateam-oracle.com/read-only-user-in-webcenter-sites/ may be of some use to you

  Kind regards

  Guddu

• How do the management interface of configuration of an ethernet interface?

  We have an ASA 5540 requiring a LAN port for failover. And the left side of the interface available only the management port. How do the management interface of configuration of an ethernet interface?

  You can disable the mode of management only on this interface to make as regualr routable port and use for other purposes, including the purposes of failover LAN database.

  On the management interface - 5510 but applies generally to the management0/0, itself including 5540

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/intParam.html#wp1057800

  Basic LAN failover configuration

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/intParam.html#wp1057800

  Rgds

  -Jorge

• 'Crypto card' to the in-house/internal interface. Possible?

  Hi, I have a two routers on a VPN to a point where the 'Crypto Map' statement is attributed to external as usual. It works fine but I need each router to a different IP address to the external interface.

  For example:

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  life 3600

  privatekey key address 4.4.4.4 crypto ISAKMP xauth No.

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac 3des

  !

  crypto map 1 VPN ipsec-isakmp

  defined peer 4.4.4.4

  Set transform-set 3des

  match the vpn address

  !

  interface FastEthernet0/0

  IP 4.4.4.4 255.255.255.252

  NAT outside IP

  IP virtual-reassembly

  10 speed

  full-duplex

  No cdp enable

  VPN crypto card

  !

  interface FastEthernet0/1

  IP 8.8.8.8 255.255.255.248

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  Instead of the "4.4.4.4" presented to the other side of the VPN, I need the 8.8.8.8 will be presented. I tried to change just the Crypto statements like below, but she always presents the 4.4.4.4 probably because of the interface that the Crypto map is applied

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  life 3600

  privatekey key address 8.8.8.8 crypto ISAKMP xauth No.

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac 3des

  !

  crypto map 1 VPN ipsec-isakmp

  defined peer 8.8.8.8

  Set transform-set 3des

  match the vpn address

  How can I make sure that 8.8.8.8 is what is presented on the other side?

  Thank you

  Andy

  Hi Andy,.

  I suggest the following command:

  card crypto-address

  http://Tools.Cisco.com/Squish/9c85B
  

  To specify and name an interface identify to be used by the encryption for IPSec traffic card, use the card crypto - local address in global configuration mode command. To remove this command from the configuration, don't use No form of this command.

  card crypto map-name - address interface id

  no card crypto name of the map address

  Example:

  interface loopback0

  IP 4.2.2.2 255.255.255.252

  !

  mymap-address loopback0 crypto card

  !

  S0 interface

  crypto mymap map

  !

  Of course, you need to make sure that the remote end can reach this additional IP address.

  Let me know if you have any questions.

  Please note any workstation that will be useful.

• Ethernet interface disappeared

  As I rebooted my laptop this morning, I didn't more wired Ethernet network. I have not installed updates yesterday, but yesterday it worked correctly. It is not a problem with the router or the cable, because it works correctly with the other laptop. The router detects when I connect the cable (the port lights) but the router has no ARP entry for the connection (only for wifi that I need to write this question). In addition, it still works the WiFi.

  Restarting the laptop does not help. I opened 'Network Preferences' and I removed the Ethernet network in order to recreate, but surprisingly, the 'Ethernet' interface does not appear in the list more (it is available WiFi, Firewire, Thunderbolt 1, Thunderbolt and Bluetooth PAN bridge). With the Network Diagnostics didn't help either. I also tried to test the equipment with the Apple Diagnostics (by pressing D when starting the laptop), but I did not need to start the diagnostics.

  It seems that the ethernet driver has been uninstalled or misconfigured.

  I have a Mac Book Pro (2011) with OSX El Capitan.

  Any advice on what to do?

  Thanks in advance

  You can take a look at the thread below.  Mac model is different, but could be the same cause as your punishment.

  Missing built-in Ethernet

• TimeMachine and two Ethernet interfaces

  OS version 6.4.2 OS X 10.11.3 (El Cap).

  That ReadyNAS has two ethernet interfaces, which I had connected without adherence to the network.

  All Mac on the network would be fix and update the sparsebundle on the ReadyNAS for some time (two days for example) and then each machine would begin to complain that the destination does not exist. One solution would be to reboot the NAS and things would work for a while.

  How I solved this problem is to simply unplug one of the NAS ethernet ports and run on a single interface.

  I guess that there is a conflict in the NAS with Hello or other discovery services and some confusion about the interface gets introduced to the network. This seems to change with the times.

  I could possibly get a switch that supports the binding, but for now I would like to be able to run both interfaces if possible (I pay for them after all)

  Hi rawb1,

  Concerning the use of multiple network cards or adapters ethernet in your ReadyNAS system, here are some useful articles from NETGEAR that you can watch.

  ReadyNAS OS 6: Set up cards under customs

  ReadyNAS - collage/team and how should I use?

  I hope this helps!

  Kind regards

  BrianL
  NETGEAR community team

• Controller time real-time FieldPoint or Ethernet interface

  Good afternoon

  The first feature listed on the PS-2000 product page is:

• Stand-alone embedded real-time controller or on PC distributed i/o Ethernet interface.

Everyone was able incorporate a PS-2000 as an Ethernet on PC distributed i/o interface?  In other words, have the PS-2000 as a FP-1600 Act?

There are some discussions forum discussions that dance around the subject, but I found no really one who responds to her.

Thank you

Ed

Hi edlad,

After playing with a FP-2010 for a while, I think you need to install LabVIEW Real-time on the controller to make it work, even though you are technically not to use it because you are not running a VI/executable on the controller. Regarding your problem with the installation of LabVIEW 8.5.1 on a PS-2000, it is disturbing because it should not be a problem that at all. In fact, I have personally been able to install LabVIEW 8.5.1 on many FP of the 2000s. For that matter, I suggest reformatting of the PS-2000 of MAX and try again.

ThinkG: Regarding your question on the use of a PSC-2220 to connect with belvedere, I don't know because the support of Lookout is managed by our subsidiary in Shanghai by e-mail only. However, I don't know that you can use this second ethernet port to connect with another network (cFP-180 x) FieldPoint module using the FieldPoint drivers. Here are some good articles about this configuration knowledge base. I hope they are useful.

http://digital.NI.com/public.nsf/allkb/F602F6F1B243282686257495007695BB?OpenDocument

http://digital.NI.com/public.nsf/allkb/67F94BB93BCE32CF86257367006B3659?OpenDocument

Thanks for choosing National instruments.

Aaron Peña

National Instruments

Technical sales engineer

http://www.NI.com/support

• Using TCP on the second ethernet interface

  Hello

  I use a PXI 8109 Pharlap module running.

  I try to use the second my PXI ethernet interface to send UDP and TCP packets. The main interface is used to manage channels Veristand.

  Here is the configuration of my two ethernet interfaces:

  -eth0 (primary):

  IP: 10.0.0.3

  subnet mask: 255.0.0.0

  -eth1:

  IP: 192.168.10.9

  subnet mask: 255.255.255.0

  For UDP, I have no problem, the packets are sent to the second interface as I want to. I think it works because there is an entry "network address" on the "Open UDP" VI so that the system can choose the right interface.

  For TCP, I use the VI "to open a TCP connection" but there is not that kind of entry. And it does not work: I suppose that the system tries to use the main interface, but it can route packets...

  For more information, my two networks is physically independent.

  Can you help me find out what is happening? Is it possible to use the TCP protocol on the second ethernet interface?

  Thank you very much

  Kind regards

  Laurent

  
  

• Difference between the series & ethernet interface.

  Hello world

  I have some doubts in basic foods.

  Q1: What are the differences between the interface series and interfaces ethernet.

  Q2: Can we use ethernet interfaces to put an end to a WAN connectivity like series. Why always we use interfaces series to connect the Wan.

  Please help me by answering these questions.

  !!!! THANKS IN ADVANCE!

  Hello

  Fast Ethernet card is one of the option for a higher speed T1/E1, other TDM options that can be offered are DS-3 and STM1 that can be offered on infra nominal basis as well. For example, you can subscribe for 10 MB BW on 45 MB access.

  The answer to your second question, is that there could be a possibility that you have subscribed for VPN (EVPL or VPLS) L2 or L3 VPN (MPLS).

  Woks of L2 VPN on labels VLAN and L3 VPN termiantes on a device of L3.

  concerning

  Navin Parwal

• of Ethernet interface input queue size/81/80 (max)

  Hello

  Anyone have the problem that the C1140 - K9W7 (or C1135) Gigabit interface

  sometimes "blockages" due to problems of queue (from what I understood it was the problems of queue)?

  I got this AP, C1140-K9W7 with IOS 12.4 (21a) JA1 and noticed that it did not

  any entry of packets to the interface, Gigabit, County of drop 0 but strangely the entrance queue

  information was that he had size 81 and 80 max... seems to me that the treatment of the queue

  code hanging somewhere...

  The output interface is OK however (the AP sends arp requests..).

  I did some research but could not find any information on this subject, also followed the

  steps to try to resolve what was causing this, without success [1]. The rating of IP traffic

  shows that the interface receives packets, but they are not under treatment and "not".

  droped too (at least the number of drop is 0).

  If I reboot the AP it works OK Yes... I can still access the console (via serial) and it

  in the case where there is no suggestion of procedure, is still in this State.

  Thanks for your time.

  John Mousinho

  [1] http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a0080094791.shtml

  Looks like this might be related:

  CSCtf27580 Ethernet interface queue entry corner of traffic broadcasting/uniGRE

  Y at - it no traffic WILL through this access point?

  The workarounds are:

  Reboot APs to bring APs back up for time being.
  
  OR
  
  go back to 6.0.188.0 code on WLC.
  
  OR
  
  Route GRE traffic away from AP's.
  
  It appears that it definitely exists in your code:
  12.4(21a)JHA          12.4(21a)JA01          006.000(196.000)
  

• Virtual Ethernet Interface identification in UCS

  I would appreciate pointers or information that will help me identify the UCS 5108 Blade Server and physical ethernet interfaces based on a value Veth # I get via CLI or SNMP of a UCS FI 6248. For example, by using the command "show table address mac - dynamic" on a CLI 6248, I get the following information:

  * 0025.b500.000e 903 Dynamics F 0, F Veth1892

  * 0025.b500.003f 903 Dynamics F 0, F Veth1676

  * 0025.b500.004f 903 Dynamics F 0, F Veth1668

  * 0025.b500.005e 903 Dynamics F 0, F Veth1884

  * 0025.b500.006e 903 Dynamics F 0, F Veth1876

  * 0025.b500.009f 903 Dynamics 10 F Veth1660

  * 0025.b500.00af 903 Dynamics F 0, F Veth1868

  * 0050.5686.5d0d 200 0 F F Veth1876 Dynamics

  * 0050.5686.5d0e 200 0 F F Veth1852 Dynamics

  * 0050.5686.5d10 200 0 F F Veth1876 Dynamics

  * 0050.5686.5d13 200 0 F F Veth1852 Dynamics

  * 0050.5686.5d17 200 0 F F Veth1916 Dynamics

  * 0050.5686.5d1c 200 0 F F Veth1892 Dynamics

  How can I find out what 5108 chassis, the uplink FEX, the physical ethernet port each of these ports Veth # are?

  TIA,

  Angel

  Hello Angel,

  The following SAM CLI command provides information of full path for server NIC / vHBA

  show circuit of service X Server profile / Y

  There are other commands that do not completely trace the path.

  connect nxos

  See the border-interfaces pinning

  See pinning server interfaces

  HTH

  Padma

• IPSEC VPN on the Ethernet Interface

  Hello

  I have a doubt on a new fundamental concept.

  If IPSEC VPN works on Ethernet Interface of router Cisco? It's IPSEC VPN can be terminated on FastEthernet Interface of the router?

  So far, I worked with Serial Interface only.

  R.B.KUMAR

  Yes it can - see the sample config below: -.

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094525.shtml

• How a GRE tunnel is applied to a physical interface?

  Within the tunnel configuration, we use the controls, the source and destination for the tunnel, but the physical interface does he know how to use the tunnel? The source code of the tunnel parameters replace the physical interface? If we don't configure a tunnel with the right source this interface would then send all information encapsulated in the GRE?

  If we also configure IPSec on the interface, and specify a card encryption to encrypt only the corresponding traffic this corresponding traffic would not use the GREtunnel or information without worrying if it was encrypted IPSec is also be encapsulated in the GRE?

  Also, I read here: https://supportforums.cisco.com/docs/DOC-3067

  'Bind the card crypto to Physics (outside) interface if you are using the version of Cisco IOS 12.2.15 software or later. If not, then the card encryption should be applied to the tunnel as well as the physical interface interface. »

  Why was it necessary to apply the crypto map to both physical and tunnel interfaces, and why is it not necessary with versions of IOS?

  Thanks for any help!  -Mark

  Hi Mark,

  When you set the source of the tunnel in the tunnel interface, the router adds the IP address of the specific interface (loopback or physical) to the GRE packet generated by the tunnel interface.

  This is useful when you need to deliver a tunnel through the Internet WILL, but the tunnel interface has an IP of priivate, if you use the interface external (with a public IP address) as the source of the tunnel.

  When remote endpoint WILL receive the packet, search interface tunnel there as destination of the tunnel and decaps the packets, and then he gets the GRE packet and forwards it to the specific tunnel interface.

  Since 12.4 you simply apply the crypto map to the interface defined as the' tunnel', usually the one connected to the Internet, where all VPN tunnels are landed. The reason for this is the endpoint VPN termination being the physical and not the tunnel interface interface.

  The reason why you need to add the encryption card for both is not clear for me, since I did not support older versions of code.

  Do not forget that when configuring a GRE/IPsec tunnel in ACL Cryptography you set the source and tunnel destination IPs.

  Hoping to help.

  Portu.

  Please note all useful posts

  Post edited by: Javier Portuguez