CSACSE-1113-K9 initial configuration for ever
Hi all
I'll put up a new CSACSE-1113-k9 (acs 4.2 device).
1st step is to perform the initial configuration by a connection serial (rs-232 port on the chassis of the device).
I already did, but whenever I try to connect to the serial port, Setup runs allover again.
Account admin, ip address, mask, etc., all that is there, but it keeps cycling through the same sequence of script, and I need to access the CLI to issue certain commands.
Tips/advice appreciated please.
Thanks in advance
JD
Hello
It's because you keep giving Yes for the test running on the initial Setup. When you are asked to test the network connectivity you enter N for which. Hope that clarifies your query.
This step is essentially running a ping command to ensure the connectivity of the ACS.
g. at the prompt, enter host name or IP address:, type the IP address or the host name of the device connected to the ACS SE and then press ENTER.
Result: If successful, the system displays the ping statistics. The system displays the command prompt: test connectivity network [Yes]:.
h. if network connectivity is confirmed in the previous two steps, at the prompt, [Yes] network connectivity Test:, type n, or N, and then press ENTER.
Tip the system continues to provide you with the opportunity to test the network connectivity until you answer No. This means that you can fix the network connections or retyping the IP address.
Concerning
Knockaert
Tags: Cisco Security
Similar Questions
-
Accidentally selected 32-bit instead of 64-bit to the initial configuration
I chose accidentally 32-bit instead of 64-bit to the initial configuration. The computer (Satellite L630) came with a disc. If I create a recovery disc it will allow me to select 64-bit or it will create just once for a 32-bit system? Is there another way that I can return to the initial configuration?
What model of laptop you have (L630-xxx)?
Create recovery DVDs and test. You should not wait for a response, just to test it.
You can also try to start installation of recovery of HARD drive, just to see what will happen.http://APS2.toshiba-tro.de/KB0/HTD9102IR0000R01.htm
-
Messed up the initial configuration of Win Vista on Satellite L40
I can only think that I messed up when performing the initial installation of Vista Home Premium on my new Satellite L40.
I finished to the high withComputer\Vista C:\Users/comet containing all my stuff AND - outside of Vista C: - a full mirror in Desktop/Chris...
Can someone tell me if I can return to the initial configuration screen and how?I tried to back up the directories and then delete them and you try to restore a single directory, but the other reappears too!
I'm obviously a complete dunce so please do not forget that and keep your simple instructions!If anyone can help then anyone know a number 0800 for Toshiba Technical Support?
Thanks in advance.
Hello
What s your problem exactly? You can start the Vista?
If so, what you want to change it or not?If you can not boot Vista and then take your Toshiba Recovery DVD and try to reinstall it again
-
Hello
With NI WSN 1.1, using a 9792, I can click on the button set the permissions, and if none had been defined would simply ask me a new administrator password. Now with NI WSN 1.2, when I click on the button set the permissions he takes me to the web interface of the 9792 and said "nobody is connected or you don't have permissions to view/edit users, groups, and permissions.» When I click on the "connect" button, a box opens and asks me a username and password. I scoured the notes version of the help files and the internet, and it seems there is NO documentation on how to set up the first name of username/password combination, or it indicates what combination of username/password default username there might be. I also tried a brand new 9792 straight out of the box and load of 1.2 to this subject and it has the same problem. Is there something obvious that I'm missing? How a person initially configure security on the 9792?
Hello, Garrett,.
Thanks for your post!
Looks like you're having need for information on how to find the information of your 9792 newspaper. When you use NEITHER-WSN 1.1 allowed us users to define the initial password and this is still the case for the 9791. The 9792 is a gateway OR WSN node and a target time LabVIEW Real-time. Its default log in information or lie in a (KB) Knowledge Base using LabVIEW or helping MAX. You use LabVIEW 2009 SP1 or LabVIEW 2010?
The default name of the user and the password is the following:
user name: admin
password:
KO
By default the username and password for the newspaper in a real-time controller
http://digital.NI.com/public.nsf/allkb/14D8257A7724BE85862577F90071B73F
Help of LabVIEW
Start > all programs > National Instruments > xx LabVIEW > LabVIEW help
Then go to... Fundamentasl > working with egalitarian and target > how-to > control and configure a remote device from a Web browser
Help MAX
Open MAX > help > MAX Help (can also press F1 if open MAX)
Then go to... Help MAX remote systems > LabVIEW Real-time targets Configuration > Device Configuration > logging into your system
The help link above LabVIEW is called in 9792 under Related Documentation start guide that directs you using LabVIEW.
NEITHER Wireless Sensor Network Getting Started Guide
http://www.NI.com/PDF/manuals/372781c.PDF
Is the information you were looking for? Please indicate if there is something else we can do.
See you soon
Corby
WSN PES OF R & D
-
LAPN300 - the best configuration for 3 access points, while using the same SSID
Hi all
What is the best configuration for 3 x LAPN300 located in various places around my house of 3 floors, access points if I want just one SSID?
I did some initial research which suggests that I can use the same SSID on all three, as long as they are on different channels. 1, 6 and 11 for example. In theory, then, as I wander around the House the client machine must auto swap to the AP with the signal stronger.
What do you think? What is the best way or do, or could suggest you something else?
As an aside... If I decided to create a second SSID for the guests at home, I would also want to add wireless isolation to this SSID. How would that be managing the DHCP server on the local network? How would be asked to connect to the SSID has never get an IP if they have been isolated from other clients on the local network? Besides, how they see the router? The ANNUAL lets you specify exceptions to this isolation for this feature? Alternatively, as I suspect, is the right isolation feature isolate them from other WLAN, not the LAN clients customers?
I did some testing and configuration of the AP with the same SSID and security will do what you want. Don't worry about setting the channel because the auto channel setting works with these devices and automatically adjusts the spacing between the appropriate channels.
Recommendation of the VPN_user is what you need if you want to isolate the SSID comments from the rest of your network clients.
Isolation of SSID of the AP will guard only wireless devices to communicate with each other on the same SSID on which it is enabled.
-
from scratch
I had to pull the battery on my dell p.c.Now I need to reset everything on the machine. I can handle most of it, but I don't ' know not the initial settings for bios and other initial set up details.» My screen there "list of questions and I n" t have the answers, it is a PHOENIX, I care. Can anyone help?Follow this. It should guide you through the configuration of your BIOS.
-
Configuration for E4200 suggestions
I just bought a refurbed E4200 and run the configuration wizard. It works fine but I know there are always better configurations and settings.
I'm out of the static IP for my devices, but don't know enough about this router beyond that.
I have an XBOX with XBOX LIVE, PS3 PlayStation Network, but also a gaming PC. They are all wired.
Wireless, we have a few desktop computers and laptops.
My previous router was a D - Link DGL 4500 and it was a great router, but has not had the MIMO or punch wireless that it is. I really like this E4200. Anyway, the DGL4500 forum was the best stickies, I have ever seen regarding the configuration for the games. Does anyone know of another forum that may have a similar one sticky for configuration or can someone suggest what works for them?
"Tweaks" are generally to solve gambling problems. I don't really think tweaking everything that would make a real difference for you. Just don't use Qos on the router again because it does not correctly detect the speed upload and Linksys leans on this.
If you have a DSL modem, then put it in Bridge mode and use the PPPoE rather than DHCP in the router Web page. If you have cable or fiber then I would think UPnP would be the only thing needed to enjoy the game smoothly.
If you are having problems then that is when port forwarding/triggering, dmz, etc. come into play. Another that I have not really seen all the articles on how to optimize the gameplay. Having enough bandwidth in combination with low jitter and latency is what counts. Maybe when they solve Qos problem, then you can try it if you have problems of upstream bandwidth.
Also make sure you have the latest firmware. Here (v1.0.02). I was checking the Dlink forums and all they did was open (done automatically UPnP) ports and prioritize the traffic (Qos). But as I said, do not use until Linksys Qos solves the problem because it will considerably cut down your download speed.
-
Initial setup for the module of firepower, where start
Hello world
Ask your help once again, first of all, I've read a ton of guide as to the initial configuration, i.e., initiate the module fire power so that covered.
Recently, one of our clients bought a new ASA with services of firepower, all is well and good, until I saw that on the nomenclature, it has SF - FP5.3.1 - K9.
As far as I know, admins are who will begin the device, for example, through to bootstrap and OUR system software desired.
My question is, what I really have to go v5.3.1? or can I just jump to 5.4? for example, to download the software "bootstrap" of 5.4 and 5.4 sys
Note This is a new ASA fresh-from-the-box-with-the-smell-of-cisco ^_^Hi LJ,.
In this case you can directly jump to 5.4 because she didn't have any configuration.
Kind regards
Aditya
Please evaluate the useful messages.
-
Installation of UCP to CSACSE-1113
Hello together,
I have installation just device CSACSE-1113 and tried to find a way to install UCP, but as far I could see it the UCP software can be installed.
I'm just looking bad or is there really no way for the installation of the UCP to the device?
It would be the right way to install UCP to another server and direct them to the GBA unit?
Sorry for the question, but I am quite new to GBA. But so far I have found many solutions in this forum, thank you very much.
Thanks in advance
Hello
UCP is installed on a different server and then pointed to the device.
Kind regards
Vivek
-
Hello
I searched many hours today in the internet and your forums, but it seems that this problem is not solved yet:
No writable calendars are configured for the invitations with the provider for Google Calendar.
My Thunderbird is 38.3.0 and the provider for Google Calendar 1.0.4.
I put calendar.google.enableEmailInvitations; true but it did not help. I also tried [email protected]... @googlemail.com. Calendar works fine, it syncs, I see all the entries etc. But I can't accept invitations even IF she must have write access.
What can I do? Is there a solution for this?
Thank you!
DanielUse CalDAV here to access Google Calendar via lightning. I have no experience with the add-on of the provider.
In any case, it is my understanding that you must assign an e-mail address to a calendar in order to be able to accept the invitations for this calendar. I see that in your screenshot.
You can try to remove the Google calendar in lightning and re-create it. Given that all the data is on the server nothing will get lost.
Or you may want to try CalDAV.
https://blog.Mozilla.org/calendar/2013/09/Google-is-changing-the-location-URL-of-their-CalDAV-calendars/ -
No writable calendars are configured for invitations
A few weeks ago I created the lightning (with the great help of the participants to the forum of TB) so that when I get an e-mail meeting invitations, I could accept, and they show up on my Google Calendar. A week ago, it stopped working.
When I receive an invitation, there is no button to accept. Instead, there is a notice that says "no writable calendars are configured for invitations, check the properties of calendar.
I made sure that Google calendar is present and selected in the tab of the Flash. I checked the calendar properties, and the email address where I receive invitations to meetings (my work email) is set as the e-mail address in the Properties dialog box. And the checkbox is enabled to turn on the calendar.
Thanks in advance, does anyone have suggestions to get TB/Lightning to work as it did before? That is to be accepted invitations to meetings and automatically add them to my calendar?
Thank you!
Well, you can then mark your message as 'Solution' for the topic?
Thank you. -
My e-mail and password are correct when I try to configure my mail in Thunderbird, but I always get the error message: Thunderbird could not find your e-mail account settings.
I have also entered with Gmail and was assured that it is configured for IMAP
Thank you.
-
SP A10 - Error 633: the modem is not installed or configured for Dial-Up
I've already reformatted the hard drive and the utility CD to reinstall the modem driver. Anyone got tips on how to solve the problem? An external modem would solve it?
Either way, it's a satellite pro A10Hello
If the HARD drive is formatted, use the recovery CD and reinstall the OS. After that, the modem must be recognized and properly installed. After that, configure Dial connection and check the modem. If the modem is not defective, it should work.
The strange thing is that there is Error 633 which means: the port is already in use or is not configured for remote access remote calls.
Please check this interesting site http://www.modemsite.com/56k/duns633.asp.
If there is no success please write again.Good bye
-
Re: Brooded and configuration for Touchpad
Win7 x 64
L505 - 10 MIt dishes all kinds of problems after an update of security windows for this system a few months ago.
I put a backup of C:\ return, but various functions did not work.
I have most of them are still working today. I installed Flashcard again but configuration for touch pad and display are still missing.
Mouse drivers are HID-mouse PS/2 version: 6.1.7600.16385 Microsoft.
I downloaded path touch driver - 20091202155841.zip, but it cannot be installed.
C: \Program Line\TOSHIBA\Bulletin Council is present but likely damaged and not present in Windows Start-menu\Toshiba.
How can I fix this?arnold12
It is pretty damn good on your laptop.
Is installation of recovery for you solution?I mean, after the new installation of the OS, everything will be OK again.
All you need to do is to backup all your data and start the installation of the HARD disk.
-
Hi, I just bought Dm11 drum machine apple app, how do I configure for use in Garageband?
I guess you mean the Mac Version of DM1. The App is not closely integrated with GarageBand. Therefore, you must export each loop/beat you like WAV or AAC and import it in GarageBand.
Maybe you are looking for
-
How can I specify the first directory when Thunderbird looks like to attach a file?
I want to easily attach a file to a standard directory, so I want Thunderbird to look here firstI specify an attachment for outgoing mail. Any suggestions?
-
HP 450-101nf: feed an its hp 450-101nf pci-e card
Hello! I have a HP 450-101 n (3.7 Gz i3, 4 GB ram, 1 slot pci-e x 1, 1 pci-e x 16 slot) and I want to connect to a map its asus xonar dx, but this map requires a separate power cable and I have not seen one inside my office. Is any possibility of fee
-
System: Windows XP Home Edition, version 2002, service pack 3 Compaq Presario desktop computer AMD Athlon XP 3000 +, 2.16 GHz Problem: Installed Firefox 4.0, worked well with tabs showing their titles on the right, such as "CNN." After the PC is rebo
-
If I buy the Windows 8 upgrade, can I still run Windows 7?
I want a license, but I don't want to use windows 8 to my computers drivers work perfectly with 8.My computer manufacturer is offering a discount of time limited to the cost of upgrade. If I buy now upgrade of windows 8, I will need to update to wind
-
Error 0 x 80070002 won't install or update applications on the store
I'm FURIOUS. I just brought my new laptop at home, installed Microsoft Office (home and the office, because God forbid a computer come with word-processing capabilities, everyone in the world needs, have to pay extra for that!). Although I bought the