Custody of cycling: writing... Connected... Disconnected

Similar Questions

• Eternal HDD PX1266E - 1 25 retains the connection/disconnection

  I have an external HARD drive, type PX1266E - 1 25, that no longer seems to connect with my laptop.

  Until yesterday, everything worked fine, but then I started to hear the connect/disconnect sounds windows all the time (a first, later others and repeated all the 1-3 minutes approximately).

  They disappear when I remove the cable of the USB ports on my laptop HARD drive.

  If I look at computer Magement - Device Manager - Universal Serial Bus Controllers, I see that whenever I hear the sound connect, Device Manager refreshes and a new item "USB Mass Storage Device" appears between 4 'Intel (r) 82801 DB/DBM USB Universal Host Controllers"and 4 'root USB Hubs' already contained. When I hear the noise of the disconnection, the USB MSD disappears again.

  Following some comments I found on the web, I've uninstalled all the USB controllers and restarted, to clean, but that made no difference.
  If I right-click on the MSD line for the short period that it is visible and select uninstall, then reboot, my computer laptop actuall does not see the external hard drive (the balloons found new hardware USB 2.0 CD + HD and found new hardware USB Mass Storage Device appeared), but the drive is not really recognized (he normally stood like a G (: hard drive).
  Sometimes I get an error message as well after you have uninstalled the drive and when it is reviewed by the PC (a third balloon indicating that a problem occurred during hardware installation. Your new hardware might not work properly), but that only seems to happen if after uninstalling, I don't not yet restarted, but at the same time the HARD drive went through his routine to disconnect/connect again.

  Any suggestions on what I can do?

  Hello

  It of difficult to tell if it s really a laptop or drive HARD USB related issue s
  In your case, I would try to connect the HARD drive to another computer/laptop to check if the same thing would happen with an other other computers.
  This will help you know if his laptop or external HARD drive issue

  But to be honest, it seems that drive TOUGH question... maybe this disconnection messages balloon appears because the HARD drive stops working.

• Wireless on Satellite Pro L10 constantly connect & disconnect

  The wireless connection on my computer worked for two years and this morning he started connect and disconnect every 5 minutes or more. The computer will work with the LAN cable but continues to connect disconnect and reconnect to the wireless network.

  I had a conversation of 2 h with a BT technician, who was no help at all

  The same thing happens on my laptop. I don t know why but the laptop disconnected every 2 minutes using WPA WLan encryption.
  It was very painful!

  I reinstalled the entire operating system and downloaded all updates from Ms. It took several hours but finally it worked!

• Connect disconnect problem (SL 500, windows7)

  Hello friends,

  I am facing a weird problem with my 500 SL with Windows 7 (I also lucid Linux installed on the system).

  (Note: my laptop came with Vista)

  As I begin my computer after it was closed (and NOT for a reboot) it keeps beeping sound from the start connect-disconnect power until I have completely load the operating system. (independent of windows or ubuntu) But after startup is complete he stops himself and he went after it. Anyone faced this problem? All thought it might be because?

  Some observations and comments on my machine.

  1. this product only when I start and the machine not on reboot.

  2. my vista has been currepted earlier. s I reinstalled using an another OEM my volume keys and the thinkvantage (blue) button does not work since then. (This beeper number is one or two weeks now)

  3. I noticed a little slow start for 7 but still all right.

  4. I have thinkvantage Manager of power installed. (It shows connected and disconnected when the ringing lights)

  5. my battery is old enough has around 30-40 min capacity.

  Could be it is bad, or the power port where it connects. Only way to check is by connecting another adapter compatible lenovo (good).

• SE connect/disconnect Internet using a command prompt

  original title: to connect/disconnect Internet

  Is it possible to disconnect & reconnect my internet connection of cable to a command line in Windows XP?

  Hey John,

  I don't know if there is a way to disable the internet connection to the modem or the router by command-line in windows. There is probably a way to disable the network adapter on the local computer through command line, but myself I do not know what commands to use.
  I know, however, that if you drop your IP address, your connection will be terminated. You can do it in the command line by using the command "ipconfig/release" without the quotes. This will minimize your IP address causing your connection down.
  You can bring it to the top by renewing your IP address. This can be done in the command line by using the command "ipconfig / renew" again without the quotes.
  Note * I believe that you must be a system administrator to run these commands.
  Now, I'm sure that's not the best way to do it, but it will certainly do the job.
  I hope this helps.

• Replace/upgrade my router after purchase/adding a 'Smart' to my network TV and now have a noise to connect/disconnect running in background.

  Original title: connect/disconnect sounds in the background

  I had to replace/upgrade to update my wifi router after purchase/adding a 'Smart' to my network TV and now have a noise to connect/disconnect running in the background, on something, every few minutes.  It does not affect the operation of my computer, but it is very annoying. Cut the old router market and connect and disconnect before replacement, but did not any noise so I don't think it is related to that.  I can't find any evidence of the old router on the computer anyway.  I hope you can help me!

  Hi Danielle65,

  You can try the following steps and check if it helps.

  Method 1:

  You can also perform a clean boot and check if it helps.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Note: Make sure that you put the computer to a Normal startup once you are finished.

  Method 2:

  You can also check in Event Viewer about what is causing the problem. Alternatively, you can publish the results, so that we can help you solve the problem.

  Open event viewer

  What are the information contained in the logs of the event (Event Viewer)

• The computer keeps a log of connection/disconnection to the network/internet?

  I experience several internet connection all day breaks.  My computer keeps a log of connection to the internet and disconnected from the internet, so I can track how many times this happens and when?

  Hello

  ·         What is a wired or wireless network?

  ·         Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: To keep a log of connection/disconnection to the network/internet, you can download and install the software. Check out the link for more information below:

  Microsoft Network Monitor 3.4

  http://www.Microsoft.com/download/en/details.aspx?ID=4865

  Method 2: You can also see the article for more information on the the event logs for network problems.

  Using event logs Windows Network Diagnostics to solve network problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/using-Windows-Network-Diagnostics-event-logs-to-solve-network-problems

  Method 3: Check out the following articles for more information about the resolution of network problems:

   

  You may experience connectivity problems or performance issues when you connect a portable computer that is running Windows Vista or Windows 7 to a wireless access point

  http://support.Microsoft.com/kb/928152

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

   

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Hope this information helps.

• I use a laptop Windows 7 in the office wireless remote for my desktop running Vista. The connection disconnects regularly "try to reconnect 1 20.

  Hello

  I use a laptop Windows 7 in the office wireless remote for my desktop running Vista. The regular connection disconnects after a few minutes, then displays the window pop-up "try to reconnect 1 20. It always with success reconnects itself during this first attempt. During the time when the connection is lost, the internet connection is fine, in other words, I could use my cell phone to browse the internet.
  Any ideas what could be causing this?
  Thank you.
  original title: remote to vista win7 desktop keeps losing connection and reconnection se

  Hello

  Follow the steps in troubleshooting section and check if that helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  See also:

  In Windows network connection issues

  http://support.Microsoft.com/kb/313242

   

  The problems of desktop remotely

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Remote-Desktop-problems

• I get an indication of the device to connect/disconnect (sound) but there is no device involved. It is repetitive and persistent and interferes with other audio.

  Computer is turned on. Everything starts as usual, then start audio data of a device connection / disconnection. The system is updated in every way.

  Found the problem. Loose connection.  Female monitor on video card got loose in its housing.

• SW2 guard connection / disconnection

  I just bought sw2 and its Dungeon, connection / disconnection every 15 seconds

  I tried on 2 phones, the same problem happened

  any solution

  Please

  Well, since it's disconnects every 15 seconds, is there any power save mode or similar in these models? If so, you can try to remove it. Otherwise, you can try another brand to see if you encounter the same behavior.

  You can also try to reset your SmartWatch 2, click the following link:
  http://Userguide.sonymobile.com/referrer.php?region=global-en&product=SmartWatch-2-SW2#resetting-you...

  But if the same thing happens, I suggest you contact the nearest service center if a technician can examine your SmartWatch 2. You can contact your local support team for more information on the nearest Center of service or how to proceed with it in the best possible way:
  http://www.sonymobile.com/global-en/support/contact-us/contact-info/

• No Notification sound when the connection/disconnection of USB device

  Hello

  I am running Windows 7 on a separate partition on a 2011 MacBook Pro (installed via Boot Camp).

  This laptop has two USB ports on the left side.

  If I connect/disconnect a USB device to the port more back, I get the notification sound as usual.

  However, if I log out these same devices to the port further there is no notification even if the devices are recognized & seem to work fine.

  Can anyone tell how to enable notification of this port please?

  John,

  Thank you for your response.

  The sound scheme has already been set to "Windows default", but just for good measure, I changed it but it made no difference.

  As mentioned be notified when you use one of the ports USB, but not the other.

  I posted this in an Apple forum & other users of this machine & installation are reporting the issue even if it seems to be a generic hardware problem & not just something on my own system.

  See you soon.

• Disable the connection / disconnection (Adobe Acrobat DC)

  How can the option "connection / disconnection" (Menu: help > login / logout) are hidden / disabled (Adobe Acrobat DC)?

  Currently, the following data in the JavaScript file is stored:
  app.hideMenuItem ("DetectAndRepair");
  app.hideMenuItem ("OnlineSupport");
  app.hideMenuItem ("LearnProduct");
  app.hideMenuItem ("About");
  app.hideMenuItem ("AboutAdobeExtensions");
  app.hideMenuItem ("endAboutPlugInGroup");
  app.hideMenuItem ("SystemInformation");
  app.hideMenuItem ("endGuideGroup");
  app.hideMenuItem ("endUsingGroup");

  Or could "SignIn / Sign Out ' (Menu: help > connection / disconnection) are disabled in the registry?

  Use of the registry keys to disable the help of more > connect / disconnect

  For continuous Build:

  [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Adobe\Adobe Acrobat\DC\FeatureLockDown]

  "bSuppressSignOut" = DWORD: 00000001

  For the classic Build:

  [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Adobe\Adobe Acrobat\2015\FeatureLockDown]

  "bSuppressSignOut" = DWORD: 00000001

  -Karan

• Students cannot "connect/disconnect the virtual machine's CD/DVD devices.

  I will start with this context (and apologies for the wall o ' text): I'm a newbie.  I took the course VMware local community college offers [VMware ESXI Server Enterprise (CIS197)], but I've not yet certified. And I don't have a real experience, except what I have taught myself so far.

  I recently accepted a position of learning associated with the College (think: glorified lab tech). I was tasked to work with stuff from VMware in the laboratory (among other things such as Cisco and Juniper equipment). There is no pass-down information like the previous left the position four months ago.

  We have a single host running ESXi 348481 4.1.0. "We have vCenter Server (5.5.0, 1312298), running on Windows Server (2008 R2, Enterprise Edition).  Access host and vCenter through two different IP, addresses using the vSphere client (either 5.5 or 4.1, using a single application - depends to know if I connect to the host or vCenter).

  At that time, the host is using local storage only (we have plans to change this, but it will take time).  The host is not a production on its own server, because it does not have a school systems.  He does, however, run a number of virtual machines in the lab, students use (Linux, Microsoft, Web design, etc.).  So, right now, I can't take it down.

  I was tasked to create a number of virtual machines that students can use to make the basic labs of Microsoft Windows 7.  So far, I have:
  -Created users, one per student, on the host.
  -Creating VMs, deploy one per student, I have a gold model vcenter.
  -Creation of roles to limit the access of students to just their VM attributed, which they access via client vSphere.
  -Created a Windows Server 2008 R2 domain controller that is also a DHCP server.
  -Created a virtual network, which is accessible only by the Windows 7 virtual machines and is not visible outside the vSphere environment (if I said this right - he does not see the Internet or school network).

  So far, it's all good.

  However, I need to be able to allow students the ability to edit the ISO file on which their VM points in order to complete some laboratories. I guess they would use the button "connect/disconnect the virtual machine's CD/DVD devices" on the taskbar (or console window). It does not work.
  I searched a lot and found that others have had the same problem.  However, all of the solutions I've tried so far have failed.  When they click 'Connect to ISO image on the data... store. "they get an error message means nothing to me,"an internal error has occurred in the vSphere Client. Details: Object Reference not set to an instance of an object. Contact VMware support if necessary.
  The role that I use for students has these settings:
  -Data store > Browse the data store
  -Virtual Machine > Configuration > change the settings of the device
  -Virtual Machine > Configuration > settings
  -A bouquet under the virtual machine > Configuration >
  -Configure CD media
  -Console interaction
  -Connection of the device
  -On
  -Power off
  -(and more, which I don't believe are important to the question)
  -State > create the snapshot
  -State > go back to the snapshot

  I tried "Virtual Machine > Configuration > add existing disk", "Virtual Machine > Configuration > add new disk" and "Virtual Machine > Configuration > add or remove an instrument" with no luck.

  Either by the way, the root account can do all these things, but no other account can - not even a game as an administrator account.

  I've seen mention I have apply the role in the data store.  It is perhaps part of the problem. I can't see the data store when I am connected to the host (wellll, I can, if I click on the host name, then on the Summary tab - but roles do not apply at this stage).  I see is 'Inventory' (which has virtual machines and Pools of resources), 'Rôles' and 'log files '.

  I can see the data store when logged in vCenter. Roles of students, however, are defined on the host computer. If I clone the role of users in vCenter and change this role cloned to have "permissions" that those who are on the host computer and then apply it to the data store, it still does not work.

  So, after all this (which I hope I've included all the necessary information), what can I do to allow the students to change ISO to which they are connected?

  Of course, if I left something, or if someone has a question, please ask.  I want to get this resolved as soon as I can.

  It turns out that I finally found the solution to the problem.

  What 'fixed', it is sufficient to vSphere Web Client to vCenter, which then allowed us to use Single Sign-On (SSO).  This, in turn, allowed us to define users and roles in vCenter (rather than having set them up directly on the host computer) which have then been applied to the VMS of students and also to the data store.

  Now, they can (de-) connect their ISOs at will.

  I find it interesting that vSphere Client (application) shows the users (and the things that they have access to), but it won't let you set of users.

• connect/disconnect triggers

  I am planing to create triggers to connect/disconnect on my production DB, while studying a document if read next line, that scare me.
  
  -Beware of the triggers of connection. If they do not work, you can not connect to Oracle.
  
  I want to know what would be the solution if this situation were to occur.

  Hello
  This is right. The SYS user does not fire the trigger you can still login with this user and fix the problem for other users.

  concerning
  Peter

• Connect/disconnect USB

  Is there an API to connect/disconnect a USB device to the host/guest?

  I don't see no function definition for such a case of use in the API... it is "mission critical", so I thought I'd ask.

  No vmware employee confirms that they don't or don't not exist?

  There is no API avaiable for the connect/disconnect USB VIX SDK operation.

  -Thank you

  Sevin.