Data burning problem

Similar Questions

• Satellite P300 19 p - CD/DVD burning problem

  Hi, I'm new to the forum and I hope somone will be able to help.

  I have DVD burning problems. When I use software engraving the image is usually copied ok and then the burning process starts, which usually lasts only a few moments, then the machine spits out the disc burnt and wasted.

  I usually use Corel DVD Copy 6, but have you tried TOSHIBA and other programs such as NERO. With the help of Corel VideoStudio, it burns discs with a success rate of 90%, but the problem comes when you try to copy my own created disks.

  I tried different types of discs (that is to say + R and - R), and I also tried burning speeds.

  Anbody else suffers from this problem?

  I have managed to find an error code 06077-26 - 2A 040902, made this average anyhting for anyone?

  TEMPRO alerts appear to have provided updates firmware for a number of other DVD players, but not for my machine? Maybe it's due a? All the drivers are up to date.

  Thanks for listening and the anybodies help is more than welcome.

  See you soon.

  In my opinion, you should not think about buying replacements. If you think that the drive does not properly contact service. If necessary the reader will be replaced free of charge.

• Satellite A500: display driver & CD burning problem

  I have problems with the Nvidia Windows Kernel Mode Driver Version 187.98. I went back to Harvey Norman where I bought it and they said to update the driver. I got the update and it still happens. Sometimes more than 6 times within a few hours.

  Now I have problems burning photos on a disc.

  I really want to have this computer at the door and I have had for 3 months and have had nothing else into trouble with him.
  All Satellite A500 work like that

  > All Satellite A500 work like that
  I don t think so

  You must use the Toshiba graphics card driver in most cases that these drivers are pre-tested and should work correctly. BIOS should be also updated!

  > Now, I have a burning problem of the photos on a disc.
  You should check if the new CD/DVD firmware is available for your CD/DVD drive.
  You should look on the European driver Toshiba page. In addition to information, you will get a few details on the firmware available.

  If there is no firmware available, then you should test different CD and DVD from different manufacturers

• data flow problem, queuing Subvi primary VI

  Ive stuck on a very simple data flow problem here, I would like to convey the data queued in the Subvi and dequeue in the main loop of the vi consumer. Ive attached the vi, since im already stuck on this problem, I was hoping I could learn a few things, especially implementation action engine in this situation

  Thank you.

  Your Subvi makes no sense since your loop will always leave after the first iteration and you always initialize your counter to 0 whenever run you it. This is a problem.

  Your code also suffers from several places that are made by the queue data. You will get undeterministic behavior since you do not know which dequeue will get the first data. In general, for a producer/consumer using the architecture queued one or more loops loops should be given enqueueing to the queue. A single loop must be made of data. These loops shuold run in parallel to each other. In your code, you can only run your Subvi whenever you press the Start button and as said you will always show the value 1 to the queue. What you need to do, is to have your Subvi managed independently once it is started. Use "Start Asychronous CAll" to start your Subvi when the Start button is pressed then let it just run. Have it post the meter to the queue. Your lower loop in main VI should remove the values and display them. You need not wait in this lower loop since it is the purpose of the dequeue. This loop will be inactive if there is no current data and run only when the data is in the queue.

  In the upper loop of your VI main remove the dequeue and the queue. You don't need them as the Subvi is all that is necessary to validate the data in the queue.

  Try this:

  

  

• DVD burning problem: I burn the movie on widescreen PAL on a DVD-R disc. I managed it burned without menu. Now, I've added a "Pan and Zoom" menu with a main marker at 00:00:00:00, 21 scene markers, and a stop at 01:29:32:17 (th

  DVD burning problem: I burn the movie on widescreen PAL on a DVD-R disc. I managed it burned without menu. I have now added a "Pan and Zoom" menu with a main marker at 00:00:00:00, 21 scene markers and a cleat to 01:29:32:17 (the end of the film). The combustion is interrupted with a message to watch a C:\Users\ianle_000\Documents\20151206160446.iso file. There is no file. The message also provides a link for an explanation. This Web page is impossible to obtain. I'm running on a PC with Windows 8.1.

  Thank you once again. I burned the DVD!

  It is the first film for which I have reached the stage of burning. I'm not sure why she didn't in the first place. I tried to burn the "no menu" version, but at the time, was shot the DVD itself - I wonder when he reached this point?

  So, I burned the "no menu" version to another DVD, that worked, then the version of menu, with no cleat to a third DVD, which reads perfectly.

  Now that I have a successful routine, I'll stick to it.

  Thanks for all your help.

  I'll close this discussion now.

• Toshiba M30-107 mast * one drive UJ-820 s with burning problems

  When I bought the laptop everything was ok, I could burn CD music, cd of data from any application. Now I can only burn CD from iTunes. When you use ITunes, I can use any kind of disc and it works fine. However, when I try to use explore to burn pictures on a disc or video with Windows media player 10, it is said, it does not recognize the drive or he manages not said there is no disk in the drive (when it obviously). Seems odd. I tried just about everything, but it's still only Itunes that works. Someone else has similar problems and how did you get around them?

  Hi André,.

  Have you checked that your optical drive is enabled windows before burning. If you right click on the drive in Explorer, there should be a 'Recording' tab click on it and check that the indicated settings are compatible with the set up you.

  It is also useful to check for virtual CD drives in Solution Explorer. If you find (other than the real drive) it will be necessary to disable them (right click) because Windows XP supports an optical drive.

  HTH

  Post edited by: NickyNoogle

• Satellite 5200 903: can't read my DVD data burning

  Hallo,

  I have a problem with my DVD/CD-ROM. He can no longer read my DVD of data (backups of my hard drives) that I burned with the same. Also it can read the DVD movie only after I put the DVD in and out a couple of times. He has no problem with the CD.

  Don't you think it's a software or a hardware problem.

  Thank you
  Matthias

  Hi Matthias,

  This sounbds as a problem of possible material for me. As you know that the laser must be re-phased to manage the DVDS and allowed tolerances are much smaller. So your device can handle CD correvtly but fights with DVDs.

  Have you tried cleaning the lens on your DVD-ROM, this can improve the situation for you.

  Good luck

• Equium M-50-216. CD/DVD burning problems

  Hello.

  I recently bought the Equium M50. Now, I can't for the life of burn me to CD / DVD.

  Initially, I put this the fact that the service IMAPI CD Burning Com has been disabled. I started and put in place tp start automatically then rebooted the machine.

  However, I can not YET write with this drive. It reads and plays CD and DVD very well, but WILL not write.

  If I slip and fall explore it tells me that the disk is not accessible, and iTunes launches just the disc from the drive.

  I tried several types of CD DVD would be too much...

  Now, like many of you guys I HATE when computers try to tell me I can't do something!

  Is this a problem that someone met before? I tried to browse the forum but you can't really see too that helps.

  Thank you.

  ADIE

  Hello help

  Believe me, I won't tell you that you can't do something, but I really do not understand that you have this kind of problems with the new unit. When you start the machine for the first time that the unit of factory settings and hardware configuration is optimized.

  Toshiba recovery image include SONIC record now software that allows you to create CDs and DVDs. You can remove and install the clean burning as NERO software and it works well. I have gift? t know what you do with your unit and why you do experiments with IMAPI-Service.

  I just recommend you to check the data of the value. There must be C:\WINDOWS\System32\imapi.exe

  If this does not please recover unit with supplied recovery media and enjoy life.

• CD/DVD burner problems said that it is damaged or missing? Anyone has any ideas to help me solve this problem?

  Hello, I'm trying to fix my burner but I tried to uninstall and reboot my computer to see if the problem might be to set but he told me that my driver cd is missing or damaged, and I don't know what to do besides put my computer back to factory settings. So if anyone knows something I can do like that I don't have to put it back to factory settings it would be great.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: My CD/DVD burner does not work and it is said that it is damaged or missing. How can I fix it?

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• DVD Burner problem

  I'm writing a DVD mastered with data. He is preparing to go, and then tells me "There was an error burning disc."  I then put in another disc and it never passes the validation errors entry screen. I bought another brand of DVD media and also a new DVD burner. I put the slow write speed as I can.

  Hello FarmBoy59,

  I suggest that you run the fixit by following the link below. This will automatically diagnose and repair problems with your CD or DVD drive when trying to read or burn media:

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  If this does not work, I suggest that you follow the steps in the link below:

  http://support.Microsoft.com/kb/314060

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in Windows

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit ourMicrosoft answers feedback Forum and let us know what you think.

• CD burning problems

  I have a Dell Inspiron 1525 with Windows Vista Home Premium.  Lately I had problems with CD burning.  If the CD or DVD already has data on it, it burns very well.  But, if I put a blank CD or DVD in the drive, my computer does not even recognize that it's there.  The AutoPlay dialog box not does not come on my screen and it doesn't have format me the drive.  In addition, it does not record anything on my computer, where it shows how much space on the disc.

  I went to the Dell website and they have downloaded a driver on my computer, but that didn't help.  They also sent my new CD burner and that did not help.

  Then, I got an external burner with its own software and it worked for about a week and now it has exactly the same problem.

  For some reason, I can only burn CDs and DVDs which already have data on them.  But if it's a blank disc, my computer does not even recognize that it's there.  In fact, when I try to burn one, he tells me to put a disc in the drive.

  How can this be repaired?

  Files can get corrupted in Windows.

  I'm glad it works again for you.

  If it happens again, it might be an idea to remove it and try it in another machine to make sure that the problem is not in the drive itself.

  See you soon.

  Mick Murphy - Microsoft partner

• Vista Media Center - DVD burning problems

  my media library began to say that error when you try to burn a dvd of a tv show, that I taped. The program is a unrestricted type and I've been able to burn these programs on dvd. My windows updates are up to date. I'd appreciate any help

  Hi David,

  Thank you for using Microsoft answers.

  I will need some additional information to help you best.

  O what is the exact error message you get?

  Ø do you have any third-party burning software installed on your computer?

  O are able to read these files in Windows media center?

  Follow the instructions below that may help you resolve the issue.

  Method 1:

  Let us try to disable antivirus and check if it works.

  Reactivate the antivirus after checking the issue.
   
  Let us try to disable the third-party firewall and check if it works.
  Re-enable the firewall after checking the issue.

  Method 2:

  Uninstall the third-party software if any burning and see if the problem is resolved.

  Method 3:

  You can try to restore your computer to a previous state and see if the problem is resolved.

  Follow the instructions below to restore your computer to a previous state.

  1. Click Start, type system restore in the search box, and then click System Restore in the list programs.
  2. If you are prompted for an administrator password or a confirmation, type your password, or click on continue.
  3. In the System Restore dialog box, click Next.
  4. In the list of restore points, click a restore point created at least a week before the current date, and then click Next.

     Note: If you do not find a restore point that is aged for at least a week, select the first point of restoration that is available.

  5. Click Finish.
  6. The computer restarts. The system files and settings are returned to the State they were when the restore point was created.

  Method 4:

  Try to install the update from the link below.

  June 2008 Cumulative Update for Media Center for Windows Vista

  http://support.Microsoft.com/kb/950126

  Check whether the problem is resolved.

  Method 5:

  See the following topic in the link below.

  What is protection against copying and how does this affect me?

  This management recorded TV in Windows Media Center: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/Managing-recorded-TV-shows-in-Windows-Media-Center-frequently-asked-questions

  See the link below for more information on burning CD/DVD with media center.

  Burn a CD or DVD in Windows Media Center

  http://Windows.Microsoft.com/en-us/Windows-Vista/burn-a-CD-or-DVD-in-Windows-Media-Center

  Please post back and let us know if it helped to solve your problem.

  Kind regards

  KarthiK TP

• Mobile data connectivity problem

  My phone shows that is has 4G in the status bar, but my application does not connect to the internet. But when I restart my device it becomes normal and same problem arises again. Can someone give me a permanent solution.

  Try the procedure described in this article to see if they help.

  If you cannot connect to a cellular network or cellular data - Apple Support

• iPhone 5 c data connection problems

  I have a 5 c iPhone running iOS 9.3.1. I can't connect to a data connection. I have 3G and LTE on and off homelessness. I was not able to connect to a given since iOS 8.x.x connectio. When I enabled cellular data, it said 3 G in the top left corner and finally changes to 1 x. If I try to load a website in Safari, I get a pop up that say 'impossible to connect to the Internet' or 'a cellular connection is not currently permitted. I had to have my SIM card fixed, so my operator gave me a replacement phone, and the upper left corner says LTE when I turned on a data connection and it worked by the fine.

  lelandsc wrote:

  I had to have my SIM card fixed, so my operator gave me a replacement phone, and the upper left corner says LTE when I turned on a data connection and it worked by the fine.

  What do you mean that you need to get your SIM card fixed? It sounds like one of two things that cause you problems, either there is a problem with your SIM, or you need to troubleshoot your phone. Have what troubleshooting you tried? You don't list everything, and if you suffer from this problem since iOS 8, I would ask why you do not have the home phone? Who provides a service for your device, Apple, an Apple authorized service provider or your carrier?

• SSHD Toshiba MQ01ABD100H - Firmware / data recovery problem

  Hello!
  I have the mission critical data on a MQ01ABD100H of Toshiba to SSHD which was in a Sony VAIO for less than one year who decided to stop working from one day to the next. All I care about is the data. A professional data recovery company apparently reputable rated player, told me that it was a "mechanical failure", said they could recover the data and gave me a quote of $1500.00. A week later I was told something different; They said the platters and heads seem to agree and the problem seems to be on the circuit board and/or flash drive, and they didn't know how to recover the data. They told me that they have consulted Toshiba too. I asked them if they replaced the pcb Board and they would not tell me or answer questions more. I have the drive in my hands and am looking for options. I really believe that my data is recoverable if the trays are okay, right?

  Here's what I know for sure; the bios of the machine of Sony VAIO Windows 8.1, correctly recognizes the drive. However, it does not start and is not accessible or recognized with cmd prompt Windows 8.1 UEFI options. The drive is not encrypted. After putting the reader into an external enclosure and its connection to another Win8.1 machine, the player starts with no extreme sounds of survey. Slowly, she clicks a few times as if the heads are looking, but then calms down and keeps running quietly. I have installed a Data Rescue PC3 software that recognizes the drive and its attributes correctly but can't read or clone. I have the Partition Wizard software mini tool, which recognizes the drive correctly, but shows the drive as being unreadable.

  That's what I'm trying to do. I'm looking for a donor on mine, with the same model drive, date, firmware, site, number of PCBS, hard drive code.

  Now, here is my unknowns and I appreciate everyone a preview with these. If I change the pcb edge myself, I need still more likely transfer the firmware for the new Board of Directors, even if I try it without doing it. I don't know where the firmware is stored, is there a rom chip or is it stored in the Flash Player. I'm not certain if, with this model of SSHD, if this can be done with replacement of the chip or the software? If it is stored on the Flash drive how is available independent of the HHD part? Must the reader Flash itself be harvested? But what happens if the flash player is bad, how can the firmware ever be recovered? Any ideas anyone? ... other than myself shot in the head, I'm kidding. I think that this may be a common problem that will often not resolved.

  I have the drive in my hands and am looking for options. I really believe that my data is recoverable if the trays are okay, right?

  I am not an expert but if applications cannot access the data and cannot read data from the SSHD then you will need professional help...

  I found the storage Toshiba page where you could get details on this SSHD
  http://Toshiba.SEMICON-storage.com/e...ient-sshd.html

  Mate good luck...