default gateway for vpngroup

Similar Questions

• How can I specify a default gateway for users of AnyConnect with a local pool of IP?

  Hi all

  This question relates to my ASA5510 8.0 software (4) running.

  For many of my AnyConnect group strategies, I use a local pool of IP to assign addresses to remote clients.  The pool is 10.1.50.1 - 10.1.50.250.  The problem is that when clients connect, they get a default gateway 10.1.0.1 it would be OK in a properly configured network, but it's not really one of those.

  I don't think there is any place where I can specify the default gateway value, is there?  What is the right way to work around this problem?

  Thanks in advance,

  -Steve

  Hello

  Find out what...

  Cisco AnyConnect VPN Client connection Ethernet card:

  The connection-specific DNS suffix. : vcnynt.com

  ... Description: Miniport Adapter virtual cisco AnyConnect VPN for Windows

  Physical address.... : 00-05-9A-3C-7A-00

  DHCP active...: No.

  ... The IP address: 10.1.50.1

  ... Subnet mask: 255.255.0.0.< subnet="" mask="" is="">

  ... Default gateway. : 10.1.0.1.

  10.1.50.1 is a part of 10.1.0.0 subnet. By design, to make the client VPN routing compatible with machines Vista. We had changed the functions of IPs for the DG on the client. It had been noticed that if you have the same DG ip address as the ip address of the virtual card it will not work. So what you see is good behavior.

  In other words, Anyconnect will show the first ip address in the subnet as the DG which in your case is 10.1.0.1.

  HTH...

  Concerning

  M

  PS: To all users whenever you post your questions and the solution given to you, work, please make sure that note you. Helping other users with the same query to get their answers in less time rather post a new thread for the same thing and waiting for responses. This saves time for the author and the person who answers to him.

• [Advanced] Is it possible to put the IP Address of the default gateway for a vmnet NAT?

  I am trying to duplicate a computer lab on my Mac environment, and I need the bridge will be located at one address other than VMWare wants to implement.  I know how to create a static IP address for a virtual machine, but I need adjust the routers option in Library/Preferences/VMWare Fusion/vmnet2/dhcpd.conf.  Will there be a networking Library/Preferences/VMWare Fusion/to allow this?  Is there something I can put before or after the "DON'T CHANGE" section dhcpd.conf that replace the parameters in this section?

  Except that, is there a way to prevent the re-writing of the dhcpd.conf file after I made a change to VMWare?  I tried it wrong in various ways, including the re - generate the hash SHA1 of the networking file and reset the modification time of the dhcpd.conf to the original time, without success.

  Here are my current settings:

  subnet 10.10.0.0 255.255.0.0 subnet mask}

  range 10.10.128.0 10.10.255.254;

  option broadcast-address 10.10.255.255;

  option domain-name-servers 10.10.0.2.

  option domain-name localdomain.

  by default-lease-time 1800;                # default is 30 minutes

  Max-lease-time 7200;                    # default is 2 hours

  option netbios-name-servers 10.10.0.2.

  routers option 10.10.0.2.

  }

  host vmnet2 {}

  Hardware ethernet 00:50:56:C0:00:02;

  fixed-address 10.10.0.1;

  option domain-name-servers 0.0.0.0.

  option domain-name ";

  routers option 0.0.0.0.

  }

  And I'm changing the gateway to 10.10.0.2 to 10.10.1.250.  Maybe VMWare requires that the first IP address as the host and the second either the entry door and rewritten if not?

  Thanks in advance,

  Dave

  I found a way to do this.  Not sure if it's official, or if it will continue to work in the future.  In addition changes nat.conf, if you simply duplicate the part of the section "DON'T CHANGE" dhcpd.conf below, then the second version of the settings will cancel and replace the first.  Here is my solution:

  # Configuration file for ISC 2.0 vmnet-dhcpd operating on vmnet2.

  #

  # This file was generated automatically by Setup of VMware.

  # See Instructions below if you want to change.

  #

  # Define us domain-name-servers to satisfy some DHCP clients

  # (dhclient such as configured in SuSE, TurboLinux, etc..).

  # We also provide a domain name to the pump (Red Hat 6.x) happy.

  #

  # VMNET DHCP Configuration. Beginning of "DO NOT EDIT ARTICLE" #.

  # Instructions change: this section of the configuration file contains

  # News generated by the Setup program. Do not change it

  # section.

  # You are free to change to everything else. In addition, this section must start

  # on a new line

  # This file will get saved under a different name in the same directory

  # If this section is edited and you try to set up DHCP again.

  # Written on the: 04/11/2015-21:15:15

  allow unknown-clients;

  by default-lease-time 1800;                # default is 30 minutes

  Max-lease-time 7200;                    # default is 2 hours

  subnet 10.10.0.0 255.255.0.0 subnet mask}

  range 10.10.128.0 10.10.255.254;

  option broadcast-address 10.10.255.255;

  option domain-name-servers 10.10.0.2.

  option domain-name localdomain.

  by default-lease-time 1800;                # default is 30 minutes

  Max-lease-time 7200;                    # default is 2 hours

  option netbios-name-servers 10.10.0.2.

  routers option 10.10.0.2.

  }

  host vmnet2 {}

  Hardware ethernet 00:50:56:C0:00:02;

  fixed-address 10.10.0.1;

  option domain-name-servers 0.0.0.0.

  option domain-name ";

  routers option 0.0.0.0.

  }

  # VMNET DHCP Configuration. End of "DO NOT EDIT ARTICLE" #.

  subnet 10.10.0.0 255.255.0.0 subnet mask}

  range 10.10.128.0 10.10.255.254;

  option broadcast-address 10.10.255.255;

  option domain-name-servers 10.10.1.200.

  by default-lease-time 1800;                # default is 30 minutes

  Max-lease-time 7200;                    # default is 2 hours

  option netbios-name-servers 10.10.1.250.

  routers option 10.10.1.250;

  }

  -Dave

• Always addressed E1500 DHCP default gateway for hotspot :(

  I have an ADSL Modem with built-in router to which the E1500 is connected via Ethernet.

  If I choose 'Automatic Configuration' for the connection setting internet on the E1500 can I enable DHCP on the E1500 but the gateway it gives to the customers is always that of itself (192.168.1.1). The bridge, it should be is the ADSL Modem (192.168.1.254).

  If I choose "bridge" Mode I can not yet activate DHCP.

  Is there a way I can use the DHCP server?

  N ° do not use the DHCP server on the E1500. You can use it if you use it as a router. You want to use this access point. Enable the DHCP server on your ADSL modem.

  Also use the bridge mode.

• Add the default gateway for the VMKernel port group

  Hello

  I use this script to create a VMkernel port group, but the last part of the gateway address of updates to script for all groups of VMKernel ports. How can I change the script so it adds the passage for the 55-CHI-VMKernel port group only. Thank you.

  $hostname6 = "host1".
  $pg = New-VirtualPortGroup-55-CHI-VMKernel - VirtualSwitch "vSwitch1' name - VLanId 55

  New-VMHostNetworkAdapter - VMHost $hostname6 - $pg PortGroup - VirtualSwitch "vSwitch1' - '10.33.1.77' IP - subnet"255.255.255.0"- ManagementTrafficEnabled $true mask

  IP address of the gateway #Add
  $netMgr = get-View (Get-VMHost $hostname6 |) Get - View).ConfigManager.NetworkSystem
  $iproute = new-Object VMware.Vim.HostIpRouteConfig
  $iproute.defaultGateway = "10.33.1.3".
  $netMgr.UpdateIpRouteConfig ($iproute)

  Have you tried it like that?

  $hostname6 = 'host1' $pg = New-VirtualPortGroup -Name 55 - CHI-VMKernel -VirtualSwitch "vSwitch1" -VLanId 55
  New-VMHostNetworkAdapter -VMHost $hostname6 -PortGroup $pg -VirtualSwitch "vSwitch1" -IP "10.33.1.77" -SubnetMask "255.255.255.0" -ManagementTrafficEnabled $true
  #Add gateway IP address
  $netMgr = Get-View (Get-VMHost $hostname6 | Get-View).ConfigManager.NetworkSystem $iproute = New-Object VMware.Vim.HostIpRouteConfig $iproute.defaultGateway = "10.33.1.3"$iproute.GatewayDevice = "vmk0"$netMgr.UpdateIpRouteConfig($iproute)
  

• Can we have different default gateway for MGMT and vMotion?

  Hello

  We run vSphere 5.1 update 3 Enterprise Edition. VLAN is implemented in our site recently.

  Network administrator assigns 3 VLAN to MGMT and vMotion VLAN10.  It also gives me different for these 2 DG VLAN (there is another local network VIRTUAL for VM).

  When I set up the IP address of vMotion, can I change to a different DG of the vSwitch MGMT?

  Thank you

  vSphere 5.1, no, you can't.

  vSphere 6, yes you can, here vmware now gave us separate stack TCP/IP for vMotion and contributes to the vCenter vMotion cross too.

• Default gateway of 8132F Out of Band

  Hello

  I want to check is Gateway default out-of-band 8132F is the same as the default gateway for the switch.

  As I'm now a default gateway of 8132F is not even as a gateway by default out-of-band.

  ---

  out-of-band interface
  IP 192.168.10.210 255.255.255.0 0.0.0.0<-- can="" assign="" another="">
  output
  default IP gateway - 172.16.0.5
  IP route 0.0.0.0 0.0.0.0 172.16.0.5 253
  ---
  Thank you!

  The exit port of the band is at the back of the switch and for out of band management. Page 93 of the user guide shows you where the port is located and has a good description of the port.

  http://Dell.to/1LAfyCM

  If you do not use the port, then there is no need to set the gateway for it.

• PowerConnect 6224 VLAN config / default gateway

  Hello

  I am new to configuring a VLAN and work with DELL going on so please forgive my ignorance.

  I joined a small agency that currently has a flat structure networking including 1 6224 linked to two 5548 one is connected to three 3548 (access), and the other is connected to a server. The 6224 connects to a proxy (default gateway), and then on the Web. All devices are currently on a 192.168.78.0 24 network with ip default gateway 192.168.80.1

  We want to segment the network using two VLAN initially. VLAN 1 user "80" and vlan 1 safety '70' and I want to clarify a few things before that I try:

  1. can you stay the ip on the network switch for vlan user ex: 192.168.80.123 or should I create a vlan separate management?

  2. I know in order for the inter - vlan, the ip of the gateway routing vlan must be on the 6224 and I then have to configure a default route to the proxy. The proxy must be on one VLAN separate or could I leave on VLAN 80 and change the ip address another que.1?

  Thanks in advance.

  I did it several times myself.  You can do almost an infinite number of ways, but it will be better to stick to certain typical networking practices.  Here is the version digest readers of what would be preferable to do so.

  1 enable routing on the switch stack.

  2. make a 80 VLAN for your network 24.80.  Assign the IP 192.168.80.1 to this VLAN.  In this way, customers will now be a ".". 1' default to the network gateway, they are on.

  3 make an another VLAN 70 for your network 24.70.  Assign the IP 192.168.70.1 to this VLAN.  This will be the default gateway for the network.  Repeat for however many VLANS / networks you want to.

  4. create a separate VLAN for his own 'bubble' network between the switch and the upstream proxy server.  (Lets call him a dummy VLAN 100 with an IP range x.x.100.x 29.  It can be just a little/29 block or something or 24 if this is confusing. Configuring the ports a few ports 'access' for this VLAN for that no marked traffic pass over this network.  Set x.x.100.1 to your Proxy Server and x.x.100.2 to your switch, then make sure you have directions on both sides about where traffic should go.

  5. save your configuration so that you have to rebuild it after a reboot.  :-)

  It will be best to set your expecations about it.  You want realistic during a weekend/maintenance window.  ARP cache and other issues can make for some downtime.  In addition, there are certainly other ways to do it, but that may be hurtful on the road when you need to increase or scale.  Two years on the road someone wondered why a default gateway is on a few eccentric IP, or there are errors of routing intermentent, etc..

  Powerconnect worldwide, just be clear what is the difference between a port of "access" to the port of 'general', and are a port 'trunk '.  Conditions may be different from the Lim to make, and if one comes to tell the world of Cisco, this may be a little different.

  Finally, don't forget to come up with a good procedure for this during your maintenance window.  Come up with a good plan documented and so well thought out, when run you it, it will be nothing more than a task in office project.

• 7048 config as default gateway. Next internet and Juniper at the break.

  Hi, we have a stack of 2 x 7048 s who are (is?) configured as a default gateway for a number of VLAN from some Dell blade chassis. I won't go into too much detail because it's more of a conceptual thing I need to know

  8 x VLANS, which are all x.x.x.254 255.255.255.0. Large. All the internal stuff works a treat.

  Now, I would like to take 48 port and plug a juniper firewall and have all the internal stuff in access internet. safely.

  I can put in place the Juniper and access the internet separately and everything works fine also. How can I join the two together? How to configure port 48 to be the gateway to the internet for all the VLANS?

  of the outside external internet connection has (internally) is 192.168.1.254. He my Juniper with 192.168.1.92 APS (UnTrust pronounced by the external router DHCP). IP of confidence of Juniper is negotiable, but currently I put like 192.168.2.1 (static) and he would have the port defined as 192.168.2.254

  Therefore, the conceptual bit to get all VLAN.254 see port 48 as the output to the internet, so I'm lokoing. Then, I need to set up DNS etc. internally and on the Gin that is the next challenge.

  Thanks in advance

  The command to enter a lane that will direct traffic to the firewall is.

  console (config) #IP 0.0.0.0 route 0.0.0.0 192.168.2.1

  The IP address 192.168.2.254 should be for VLAN 10 on the 7048. And then no other VLAN must be in the 192.168.2.x broadcast domain.

  Console (config) #interface vlan 10

  Console (config - vlan) #ip address 192.168.2.254 255.255.255.0

  Then, to relay DHCP packets to the DHCP server, you would add the command ip assistance

  Console (config) #ip helper-address 192.168.1.92 dhcp

• S170 as default gateway

  Hello.

  Simple enough question. I anticipate using a S170 as default gateway for a specific network. The topology is attached.

  Can it be done or the S170 is not able to handle protocols other than http?

  This isn't a firewall or the router or switch.

  Something that has been done at the time was a topology like yours, but on the same network ("passthrough").  That is not supported (I don't know if it was ever actually) and I don't think it works more...  In addition, cards they use aren't opened, so if something goes wrong with the box, the link is broken...

• Cannot ping the default gateway with Centrino Advanced-N 6235 on XPS 12 but CAN connect to the Internet

  I have a XPS 12 with an Intel Centrino Advanced-N 6235 wireless card.  I can't ping the default gateway with the wireless card.  When I use a USB network adapter, I can ping the default gateway for the wired connection.  I can connect to the Internet and the internal network with the wireless card and can ping other computers on the network.  I am trying to run a program to connect wireless to a projector.  I have two different programs for the two different projectors.  I can connect by cable but not wireless.  I think that the problem is anything that does not make me a ping of the default gateway or something on the wireless card.  I have a 10 latitude with a Broadcom wireless card that is connected to the same access point and can ping the default gateway and can connect wirelessly to two projectors.  They all have two windows 8 Pro.

  I downloaded the new drivers from Dell, uninstalled, reinstalled, tried to update Windows install the drivers, all with no success. Any ideas?

  The solution of the problem by chance.  I was connected to the computer with a different network than what has been used to authenticate user account on the wireless.  When I switched the user account for the user account that was logged on to the computer was the same who authenticate to the wireless, it worked.  Go figure!

• VKernel default gateway - VLAN

  Hi guys

  If I understand well here it is recommended to have vmotion and traffic management on different VLANS, which means that different gateways

  http://www.yellow-bricks.com/2011/03/22/ESXi-management-network-resiliency/

  I created 25 VLANS for traffic management and the gateway 10.10.25.1

  and VLAN 28 for Vmotion gateway 10.10.28.1

  But how do I managed to get this to work with different gateways tw2? Since there is only a single default gateway of vkernel.

  Thank you very much

  You do not use a gateway for the subnet of vMotion.  Practically vMotion traffic should not be routed you don't need a gateway.  When you configure the vMotion VMkernel port, it will show the default gateway for the other subnet.  You can ignore that.

• Cannot remove the VMkernel default gateway

  Guys,

  I'm setting up some new ESX 4.1.0 servers and I'm running into a strange problem.  I create a new VMkernel port, according to my usual process, I leave VMkernel default gateway blank.  However, after you create the port I noticed the default gateway has filed is filled.  I; ve tried deletig the Group of ports and rercreating, but it continues to be.

  Is it all the same installation of the gateway using esxcfg from the console (I don't know how to proceed to the service console)?

  Thank you.

  Hi Peter,.

  If I remember correctly, you can have only a single default gateway for all your VMKernel ports. If you have set once this default gateway, this value is displayed on the screen of each VMKernel port configuration.

  Take a look at the command-line 'esxcfg-road' to see what can be done.

  Good luck.

  Concerning

  Franck

• L10-202: Modem: default gateway server error

  I have a new L10-202. It came with XP Home and I reformatted the drive and installed XP Pro and reinstalled Toshiba Utilities. I installed a Linksys wireless router and a linksys Pmica card. The wireless connection is good and if I connect the router directly to the wired LAN, it works very well, too. But when I connect the computer directly to the modem I get an error of default gateway server. Its like its waiting for the router online. I checked all my Windows settings on your desktop that works very well with no luck. Can anyone make a suggestion?

  Thank you.

  Hello

  Have you tried using the modem without the PCMCIA card?
  I m not 100% sure, but maybe the modem doesn't work because the router wifi and pcmcia card are enabled and connected.
  I'll try to use the modem without the router and the wireless card.

  Good bye

• OfficeJet Pro 8000: installation of the driver wireless Officejet 8000 Pro says default gateway is 0.0.0.0

  I'm chasing a well-documented problem of my printer lost network connection after a variable period of printing to do not. The only way to connect is to change the power supply, but the printer may take 5 minutes to blow and grunts until it settles and prints...

  I put a static IP address on the printer (10.0.0.250) as well as an empty default gateway successfully, and the documents are printed after 5mins of blowing and grunting (save the regular lost connection which I'm hunting...).

  I put what I thought has a static IP address on the router to match (see image below), but now I don't know if it was necessary, and if the 'hosting of the fixed DHCP server' is correct. It might be useless and missleading...

  Using the configuration of the printer to 10.0.0.250 interface, it seems to accept the installation of the network when the default gateway is blank. With the help of 10.0.0.2 caused the 'page not found' error in my browser (Chrome).

  However, when you try to reinstall the drivers, the installer has grumbled to the default gateway is set to 0.0.0.0, which currently is the only way it will work...

  The Win7 PC is plugged into the router.
  The printer wireless to the router.

  ipconfig on the pc gives Ethernet card details below.

  So basically I have no idea what I'm doing...!

  ==============

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  Link-local IPv6 Address...: fe80::c8e1:63ef:85e0:7 24% 13 c.
  IPv4 address...: 10.0.0.249
  ... Subnet mask: 255.255.255.0.
  ... Default gateway. : 10.0.0.2.

  Router config.

  

  Thank you for your comments. It seems that I solved the problem of the default gateway. Time will tell if the remains of the printer connected through long periods of no use (see update below).

  It seems that the configuration of the router of the "DHCP fixed existing host" has nothing to do with the device assigned a static IP address. In fact, it seems that this setting prevents the printer through a default gateway of the router address.

  I noticed that when you give the PC a fixed IP, it connected through the router without any other configuration of router. If I reasoned that it may be applied to the printer also, so I moved the printer 10.0.0.251 and Bingo! the default gateway can be set to the IP address of the route.

  Since then I downloaded to other updates, which is supposed to correct the common problem of wireless printers, loss of the connection.

  I'll try to report in the next few weeks an update about the stability of connection network printers.

  UPDATED: May 23, 2016

  And more of the foregoing, my router support suggested I increase a parameter "timeout" from 24 hours to 10 days. I did it more than a week. Today, the printer worked after the impression of not for about 5 days