S170 as default gateway

Similar Questions

• L10-202: Modem: default gateway server error

  I have a new L10-202. It came with XP Home and I reformatted the drive and installed XP Pro and reinstalled Toshiba Utilities. I installed a Linksys wireless router and a linksys Pmica card. The wireless connection is good and if I connect the router directly to the wired LAN, it works very well, too. But when I connect the computer directly to the modem I get an error of default gateway server. Its like its waiting for the router online. I checked all my Windows settings on your desktop that works very well with no luck. Can anyone make a suggestion?

  Thank you.

  Hello

  Have you tried using the modem without the PCMCIA card?
  I m not 100% sure, but maybe the modem doesn't work because the router wifi and pcmcia card are enabled and connected.
  I'll try to use the modem without the router and the wireless card.

  Good bye

• OfficeJet Pro 8000: installation of the driver wireless Officejet 8000 Pro says default gateway is 0.0.0.0

  I'm chasing a well-documented problem of my printer lost network connection after a variable period of printing to do not. The only way to connect is to change the power supply, but the printer may take 5 minutes to blow and grunts until it settles and prints...

  I put a static IP address on the printer (10.0.0.250) as well as an empty default gateway successfully, and the documents are printed after 5mins of blowing and grunting (save the regular lost connection which I'm hunting...).

  I put what I thought has a static IP address on the router to match (see image below), but now I don't know if it was necessary, and if the 'hosting of the fixed DHCP server' is correct. It might be useless and missleading...

  Using the configuration of the printer to 10.0.0.250 interface, it seems to accept the installation of the network when the default gateway is blank. With the help of 10.0.0.2 caused the 'page not found' error in my browser (Chrome).

  However, when you try to reinstall the drivers, the installer has grumbled to the default gateway is set to 0.0.0.0, which currently is the only way it will work...

  The Win7 PC is plugged into the router.
  The printer wireless to the router.

  ipconfig on the pc gives Ethernet card details below.

  So basically I have no idea what I'm doing...!

  ==============

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  Link-local IPv6 Address...: fe80::c8e1:63ef:85e0:7 24% 13 c.
  IPv4 address...: 10.0.0.249
  ... Subnet mask: 255.255.255.0.
  ... Default gateway. : 10.0.0.2.

  Router config.

  

  Thank you for your comments. It seems that I solved the problem of the default gateway. Time will tell if the remains of the printer connected through long periods of no use (see update below).

  It seems that the configuration of the router of the "DHCP fixed existing host" has nothing to do with the device assigned a static IP address. In fact, it seems that this setting prevents the printer through a default gateway of the router address.

  I noticed that when you give the PC a fixed IP, it connected through the router without any other configuration of router. If I reasoned that it may be applied to the printer also, so I moved the printer 10.0.0.251 and Bingo! the default gateway can be set to the IP address of the route.

  Since then I downloaded to other updates, which is supposed to correct the common problem of wireless printers, loss of the connection.

  I'll try to report in the next few weeks an update about the stability of connection network printers.

  UPDATED: May 23, 2016

  And more of the foregoing, my router support suggested I increase a parameter "timeout" from 24 hours to 10 days. I did it more than a week. Today, the printer worked after the impression of not for about 5 days

• Qosmio X 305 comes down from the default gateway - unable to get internet

  We have a few laptops Qosmio X 305 to my place of work and of them at one time or another gout setting "default gateway".

  Making it impossible to get out of the internet.
  And even if you try and add the gateway by default in, the setting will not stick.

  We use dhcp in our environment, so there shouldn't be anything in conflict with this setting.

  Someone at - he heard of that happening?

  We use Vist 64 bit. I guess the problem is with the nvidia driver. Help, please

• Satellite L300, default gateway down on WAN IP Configuration settings

  I have a metered on a Vista 32 bit and have no default gateway listed in my ip configuration settings. Yesterday I re-installed all wireless drivers and if it works. Today, after having been shut down correctly, I turn it on, and the problem is back. I still had the drivers on a USB key, so I have re-installed, but no result. Is this a hardware problem? Today, it seems weird to me that what worked yesterday is useless!

  Hello

  You must first update the Wlan dirver to the latest version:
  http://APS2.toshiba-tro.de/WLAN/

  Also, don't forget you have the latest version of the BIOS and that your Win Vista is up-to-date.

  Please also reset the WLan router.
  I had this problem a few months ago, she was related to the configuration of the router too. I rested it and it worked.

• get the address of a default gateway

  Hi all

  I saw a TCP library function that can get the address of the host.  but someone do it now, how to get the address of a default gateway?

  for example

  192.168.0.4 IP (this ip address can get according to get host address)

  subnet 255.255.255.0

  Deault gateway 192.168.0.1

  B.R

  Gerry

  Hey Gerry--

  To get the default gateway, you'll want to use the IP Helper Win32 API.  Unfortunately, this part of the Win32 API is only available for users of the full package LabWindows/CVI.

  To retrieve IPV4 information about your network adapters, you can use the GetAdaptersInfofunction.  If you need IPV6 information, you will need to use GetAdaptersAddresses.  I wrote a small example of GetAdaptersInfo and attached to it, you can see the result below:

  

  Let me know if you have any questions-

  NickB

  National Instruments

• The default gateway is missing

  I installed a new internal hard drive and lost internet service because of a default gateway missing, how to fill out my missing default gateway.

  Hi shimko66,

  Thanks for posting in the Microsoft community!

  (1) Windows operating system you are using?

  Method 1:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Method 2: We can reset the TCP/IP stack and see if it can resolve the issue.

  Follow the steps below to reset the TCP/IP stack.

  1) click Start

  (2) type CMD into the search bar

  (3) right-click and open as administrator command prompt

  (4) in the command prompt window, type the following commands:

  netsh winsock reset catalog

  netsh int ipv4 reset reset.log

  netsh int ipv6 reset reset.log

  (5) restart the computer.

  Reset the default router by pressing the reset for 15 seconds with power button.

  > Turn off everything, modem, router, computer.

  > Connect the modem to the WAN/Internet port on the router.

  > Connect the computer to one of the router's LAN/network ports.

  > Turn on the modem, wait for triggering connect light.

  > Switch on the router, wait two minutes.

  > Start the computer.

  Please post back if you have any questions about Windows. I will be happy to provide you with the additional options that you can use to get the problem resolved.

• My internet connection laptop keeps dropping out. This utility solves temporarily, saying the default gateway of something is not available.

  My internet connection laptop keeps dropping out. This utility solves temporarily, saying the default gateway of something is not available. How can I permanently?

  Hello

  1. who is the operating system installed on your computer?

  2. are you using a cable or a wireless Internet connection?

  3. were there any changes or updates made on the computer?

  4. what store did you try?

  Follow the steps mentioned below and check.

  Method 1: I suggest you to return the item and check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  You can try resetting WINSOCK, TCP/IP IPv4 and IPv6 TCP/IP stack.

  a. Click Start and in the search box, type cmd.

  b. right click on command prompt, select "Run as Administrator" to open a command prompt.

  c. at the command prompt, type the following commands:

  netsh winsock reset catalog, which resets the WINSOCK entries to the default installation

  netsh int ipv4 reset reset.log that resets the stack TCP/IP IPv4 default installation

  netsh int ipv6 reset reset.log resets the IPv6 TCP/IP stack by default installation

  d. restart the computer.

  Method 3:

  Reset the default router by pressing the reset for 15 seconds with power button.

  a. turn off the modem, the router and the computer.

  b. connect the modem to the WAN/Internet port on the router.

  c. connect the computer to one of the router's LAN/network ports.

  d. turn on the modem, wait for triggering connect light.

  e. turn on the router, wait two minutes.

  f. start the computer.

  g. when the computer is completely loaded, check if the problem persists.

• M604: M604 how to change the default gateway

  How can we change just a default gateway on the M604 by using the HP installation CD?

  Thnak you.

  Here is what we were doing this was a quick and easy solution:

  Press the home button on Control Panel.

  Open these menus:

  Administration

  General settings

  Restore factory settings.

  A verification message indicates that supplementing the rest function could cause loss of data. Select "Reset" to complete the process.

  The printer restarts automatically after operation comletes.

  Use the installation CD to run the installation with the correct settings.

• My Windows XP computer doesn't have internet access. I tried ipconfig and it shows default gateway.

  I have Windows XP Home... and all of a sudden I get no internet access.  When I do ipconfig... it does not show a default gateway.  I did everything update driver LAN, resetting the router, restart, by specifying the IP address (from the automatic ip configuration) and is still not available.  I know that the router is that I can access it from another computer.  any help would be greatly appreciated.

  original title: default gateway problem

  Is the connection wired or wireless?

  What version of XP, including service pack? (do right click my computer and select properties for info)

  It happened just before this problem occurred (failure, virus infection, etc.)?

  If this is a wired connection (which, I suppose, since you mention the 'LAN' pilot), have you tried to connect the Ethernet cable into a different socket on the router, (b) using an Ethernet cable from verified (maybe the computer that works), or (c) confirming that the Green LED next to the computer's Ethernet Jack lights up when the cable is connected?

  Given that you know about ipconfig, it would have helped if you had provided the results of the ipconfig command.  Here's a way to do it, but first configure the card to obtain an IP address automatically

  • Open a command prompt window
  • Type the following lines and press ENTER after each line

  ipconfig/all > "% userprofile%\Desktop\ipinfo.txt".
  Notepad '% userprofile%\Desktop\ipinfo.txt '.

  • Copy and paste the contents of the Notepad document in your response.  Close the command prompt window and the window of Notepad and remove ipinfo.txt from your desktop.

• My internet rpet 'unidentified network' + "the default gateway is not available"...

  My internet was working fine before, but now repeat me 'unidentified network' and I know that's not my internet because I have another laptop that uses the internet itself very well. Then when I try to solve problems, he said "the default gateway is not available"... of the suggestions?

  Hello

  ·         Did you do last changes made on your computer before the show?

  ·         Using internet connection wired or wireless?

  Method 1:

  Follow the steps in troubleshooting from the link and check if that helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  Temporarily disable the firewall on your computer and check if it makes a difference.

  Reference:
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  Note: Makes sure to turn Windows Firewall back, once you have done the troubleshooting.

  Method 3:

  Reset WINSOCK, TCP/IP IPv4 and IPv6 TCP/IP stack.
  a. Click Start and in the search box, type cmd.
  b. right click on command prompt, select "Run as Administrator" to open a command prompt.
  c. at the command prompt, type the following commands:
  netsh winsock reset catalog which resets the WINSOCK entries to the default installation.
  netsh int ipv4 reset reset.log that resets the stack TCP/IP IPv4 default installation.
  netsh int ipv6 reset reset.log resets the default install IPv6 TCP/IP stack.
  d. restart the computer.

  Also, see this KB article:

  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357

  Kind regards

• default gateway is 98.218... not 192.168.1.1help

  I can't access the 192.168.1.1 Linksys been thru step page a lot and my time to pings... WiFi is turned on my wrt54 but I can not connect via laptop... any help is appreciated. I reset for 30 sec and when I go in to check the ip address after release and reset its still not 192.168.1.1.

  Microsoft Windows XP [Version 5.1.2600]
  Copyright (C) 1985-2001 Microsoft Corp.

  Windows IP configuration

  Name of the host...: DESKTOP
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.
  ... DNS suffix search list: hsd1.va.comcast.net.

  Adapter Ethernet Local Area Connection 11:

  The connection-specific DNS suffix. : hsd1.va.comcast.net.
  ... Description: Card Fast Ethernet of Linksys LNE100TX (v5) A
  developments
  Physical address.... : 00-12-17-4F-36-CE
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  ... The IP address: 98.218.163.73
  ... Subnet mask: 255.255.252.0.
  ... Default gateway. : 98.218.160.1.
  DHCP server...: 68.87.73.12
  DNS servers...: 68.87.73.246
  68.87.71.230
  Lease obtained...: Wednesday, March 3, 2010 16:12:19

  End of the lease...: Sunday, March 7, 2010 16:12:19

• Default gateway disappears after installing SP2.

  Hi people

  I just installed SP2, and now when I start/restart the computer, the default gateway is missing. When I check the properties of the connection, the IP address is correct, but the default gateway is blank - it does not 0.0.0.0, there is nothing at all.

  My computer (Vista Ultimate x 86) and a XP Pro PC are connected to a router. I have disabled the DHCP on the router and use a static IP address for each computer. The XP machine is rarely used. I also have a configuration of the VPN connection. When I first encountered this problem, I deleted the VPN connection in case the PC tried to use it to connect to the Internet. I later recreated once I realized what the problem was.

  Even if I can reset the bridge, I don't want to have to do this every time that I reboot.

  **************************************

  ipconfig on my Vista PC at startup:

  Microsoft Windows [Version 6.0.6002]
  Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

  C:\Windows\System32>ipconfig/all

  Windows IP configuration

  Name of the host...: OS
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Ethernet connection to the network space 2 card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Bluetooth PAN network adapter
  Physical address.... : 00-11-67-AA-AC-D3
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  ... Description: Marvell Yukon 88E8056 PCI-E Gigabit Ether
  Net controller
  Physical address.... : 00-1E-8C-B7-D9-76
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::980c:2d5d:1cd3:4195% 10 (Preferred)
  IPv4 address: 192.168.1.100 (Preferred)
  ... Subnet mask: 255.255.255.0.
     ... Default gateway. :
  DHCPv6 IOOKING...: 251666060
  DHCPv6 DUID customer...: 00-01-00-01-0F-F2-6D-55-00-1E-8C-B7-D9-76

  DNS servers...: 192.168.1.254
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {9E323F18-CB91-4524-B5E3-64A8C101B
  078}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 17:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {5A583DB0-C514 - B 49, 6 - 9D1A - 2703884-6
  AFB}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  C:\Windows\System32 >

  **************************************
  **************************************

  After resetting the gateway:

  Microsoft Windows [Version 6.0.6002]
  Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

  C:\Windows\System32>ipconfig/all

  Windows IP configuration

  Name of the host...: OS
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Ethernet connection to the network space 2 card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Bluetooth PAN network adapter
  Physical address.... : 00-11-67-AA-AC-D3
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  ... Description: Marvell Yukon 88E8056 PCI-E Gigabit Ether
  Net controller
  Physical address.... : 00-1E-8C-B7-D9-76
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::980c:2d5d:1cd3:4195% 10 (Preferred)
  IPv4 address: 192.168.1.100 (Preferred)
  ... Subnet mask: 255.255.255.0.
     ... Default gateway. : 192.168.1.254
  DHCPv6 IOOKING...: 251666060
  DHCPv6 DUID customer...: 00-01-00-01-0F-F2-6D-55-00-1E-8C-B7-D9-76

  DNS servers...: 192.168.1.254
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {9E323F18-CB91-4524-B5E3-64A8C101B
  078}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 17:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {5A583DB0-C514 - B 49, 6 - 9D1A - 2703884-6
  AFB}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  C:\Windows\System32 >

  **************************************

  Can someone tell me what is the cause, please? I would also appreciate it if someone can tell me how I can configure the default gateway by using a batch file executed with administrator privileges. That would save me having to dig through Control Panel etc etc every time my computer starts.

  Thank you!

  Hi RealBlood,
  Thank you for visiting the Microsoft Answers forum.
  To solve your problem follow these steps:

  Repair options for TCP/IP stack for use with Windows Vista.

  Start, Programs\Accessories and right click on command prompt, select "Run as Administrator" to open a command prompt.

  In the command prompt window that opens, type type the following commands:

  Restore the default install WINSOCK entries: netsh winsock reset catalog

  Reset the battery TCP/IP IPv4 default installation. netsh int ipv4 reset reset.log

  Reset the battery TCP/IP IPv6 default installation. netsh int ipv6 reset reset.log

  Reboot the computer.

  Reset the default router by pressing the reset for 15 seconds with power button.

  • Turn off everything, modem, router, computer.
  • Connect the modem to the WAN/Internet port on the router.
  • Connect the computer to one of the router's LAN/network ports.
  • Turn on the modem, wait for triggering connect light.
  • Turn on the router, wait two minutes.
  • Start the computer.

  When the computer is completely loaded, we will see that.

  Hold down the Windows key and press R, then type CMD to open a command prompt:

  In the command prompt window that opens, type type the following command:

  IPCONFIG/ALL

  Right click in the command window and choose select all, and then press enter.
  Paste the results in a message here.

  Martin
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• WRT350N: how to specify the default gateway?

  Hello

  I want to use my wrt350n as dhcp server, but to specify another router as the default gateway.

  I have my wrt350n (192.168.1.254) and another modem/router (192.168.1.1). When a client connects to the wrt350n, it is automatically assigned as the default gateway address of the wrt350 (192.3168.1.1). I would like to change it to refer to the other address 192.168.1.1.

  Thanks for your comments

  Raph

  On the configuration, on the basic settings tab page, there is facility of the Internet and network configuration. Setup of the Internet is for the WAN. Assign The DHCP Auto - Configuration so it will automatically get an IP address from the modem/router.

  On the configuration of the network, local IP address should be 192.168.2.1, subnet mask 255.255.255.0. This is where you enable DHCP. The default gateway should be 0.0.0.0 and that's fine, it assigns the LAN IP of the router.

  Once you have saved it, your router configuration page now is 192.168.2.1 and configuration page of your modem/router is 192.168.1.1.

• Some clients get assigned to WRT300N, while others do not have a default gateway

  Two existing working posts, existing wireless phone and other wireless cable connects to the internet very well.

  Try adding cell phones work, they aquire signal wireless, gets the assigned DHCP IP address but can't connect. Looked at the output of ipconfig and shows no gateway by default - IP of the router is 192.168.1.1 - with everything by default, I did a reset on it.

  The existing machines have all default gateway assigned. Only difference I see is working machines are XP pro. Never had a problem with laptops work connect anywhere else.

  Any ideas on how to install in order to work laptops can connect?

  namralk wrote:

  Ethernet VMware Network adapter adapt VMnet8:

  The connection-specific DNS suffix. :

  ... Description: VMware Virtual Ethernet adapt for VMnet8

  Physical address.... : 00-50-56-C0-00-08

  DHCP active...: No.

  ... The IP address: 192.168.1.1

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  You've configured vmware on your computer to use 192.168.1.1 on the adapter VMnet8. This means that the computer uses 192.168.1.1 itself on this card and obviously will not be resolved 192.168.1.1 as default on your wireless adapter gateway 192.168.1.1 is the computer itself.

  Correct your network configuration in vmware. After that a "ipconfig / renew *" or a reboot must get a new lease of work, including the default gateway. Make sure that vmware does not use the 192.168.1.0/255.255.255.0 subnet for network cards.