DELL PowerEdge R710 and PERC H700 RAID driver for WIn 2008 Std

Hi all

I have a DELL PowerEdge R710 with a controller RAID PERC H700.

I try to install Windows 2008 Std 64 bit, but I can't find the driver. Even for the site web at Can someone help me.

THX in advance


Even if you use a driver of 2008, it should at least recognize it, then you must be using the wrong driver or something wrong :)

If you are installing 2008 R2, make sure that you use this file:

If you install 2008 x 64, make sure that you use this file:

With one, you must first unlock the .exe (right click on the .exe, properties, unlock), unzip / extract the files (run it and make a note of the default location), and then copy the 4 files on a CD, USB, etc., then when Windows tells you that he is not all hard disks, click on the link drivers load below to load the drivers from the media you have chosen.

Tags: Dell Servers

Similar Questions

  • PowerEdge R710 and perc h700, disc not visible in OS


    We have PowerEdge R710 with perc h700 raid 5 controller physical drives under raid6 running. We have recently added a sixth of the road which is much smaller (512 against 4 TBS) we want to just format and use it as a normal drive in the OS (Ubuntu 12.04.5).

    However, the drive is not visible in the operating system. When you enter the settings of the RAID controller that it says that the drive is READY but not configured and all the options to the title of operations are grayed out. How can we make this hard drive is visible in the operating system?

    See you soon

    The H700 does NOT support non RAID, so all records first must be configured on the controller, before its presentation to the BONE. You must configure (initialize) as a single drive RAID 0.

  • Dell PowerEdge R710 memory upgrade 16 GB (4x4Go) for 72GO with more than 64 GB (8x8Go)

    Hi all

    My Dell PowerEdge R710 is seen 16 GB (4x4Go) now and would like to add 64 GB (8x8Go), it will be total 72GB. Please help me add memory into the slot on the right. Can I do the following as below

    A1/B1 > 8 GB

    A2/B2 > 8 GB

    A3/B3 > 8 GB

    A4/B4 > 8 GB

    A5/B5 > 4 GB

    A6/B6 > 4 GB

    Thanks Robert, I already bought 64 GB (8x8Go) and would like to add to my current server which is running 16 GB (4x4Go). So, please show me how.

    Thank you

    Binh Kien

  • PowerEdge R310 and Perc H700

    I have an older R310 which does NOT support the hot-swappable drives and I'm looking to add a raid card Perc H700.  A few quick searches show only cables for installation bottom of basket.

    So I'm not the guy of material more experienced so there cables that go from the H700 to readers SAS?


    It should be X394K part number. The description is HARD drive cable. PERC H200/H700 HDD card

  • Dell PowerEdge 2900 - need to use internal drives for RAID

    Hi all

    I am the I.T. guy for small business from my father. I help them on the side.

    They have recently purchased a PowerEdge 2900 server used with 4 internal SCSI drives

    This server also has a Dell SAS 5 / i integrated controller

    I want to install Windows 2008 R2 standard on this server and use it as a file server and a place to host QuickBooks Enterprise.

    The problem, in that I am running is that I can't find in the Bios or anywhere in the server startup utilities where I can configure the 4 internal drives as a RAID 5 array. I want to do this and THEN install the Windows Server operating system. I used the last Build Server utility Dell and also updated all the firmware to the latest versions. The Build Server utility doesn't let me configure the RAID array.  What I'm missing here?

    Thank you very much for your help!

    I upgraded to a PERC 6 / i integrated RAID controller and now problem is solved. Just need a new controller internal RAID.

    Problem is solved!

  • Adding additional disk to ESXi 4.1 Datastore on Dell PowerEdge R710


    We currently have a Dell PowerEdge R710 with 6 SAS das drives configured in a RAID-1/RAID-5 configuration. A drive is configured as a global hot spare. I would add this spare drive in the RAID-5 table, where some virtual machines live, to recover additional space. Has someone managed to do this? Is the only way via the PERC BIOS management utility?

    Thank you!

    I'm not part "raid-1/raid-5.  But assuming that the table is raid-5, then yes it is possible and yes the BIOS utility is necessary.  The hot spare is currently set should be removed from this role, then added to the existing Bay raid-5, but without the ability to select increase.  This will create free space on the raid-5 array on which then a new logical volume can be created, which will be then seen by ESX as a new drive and therefore another data store can be added to this (or it can be added to the first as a measure).  HTH

    Please give points for any helpful answer.

    Unofficial list of transfer USB devices work


    Hello (or rather the night).

    I have a dell poweredge R310 (with PERC H700) server and 3 hard drives.

    The first two are the storage on SATA drive with a capacity of 3 TB (each 6 to total) this operation of RAID 1.

    The third is a 64 GB SSD for boot into the operating system (I chose to set up Debian).

    I read a few topics who insist to start using UEFI and put the storage disks to GPT for the OS can fully recognize.

    If I could access the UEFI interface, with the configuration of raid PERC H700, but I can't find any indication of the GPT.

    How can I go about it, is that I missed a step?

    Hoping that someone will help me :)

    No, TPG is a function of the operating system, NOT the hardware, so if the PERC does not recognize the full capacity of disc, then either your H700 firmware is old (> 2 to support has been added in the second update of firmware for this card) or the drive is not compatible.  What make and model are you using?

  • Satellite C50 - B - Intel Trusted execution engine Driver for Win 7 required

    Cannot find driver Intel Trusted execution engine for Win 7
    It is not listed on the page of product support for Satellite C50 B?

    Device Manager searched this driver and I downloaded the driver for Win 8.1.
    Device Manager not more indicates the absence of the driver, but I don't know if the substitute to Win 8.1 driver works for Win 7.

    Sorry for the English, google helped me.



    The Intel Trusted execution engine driver to Win 8.1 64-bit seems to be compatible with Win 7 64 bit system.
    This is why you should not be worried that installing this driver can cause a few problems.

  • PERC H700 RAID 5, 3 disks, 1 Reporting failed and 1 predictive failure


    I have a PowerEdge T410 with a PERC H700, RAID 5 with 3 disks.  The controller reported a failed drive so I replaced the week last with a drive of new/refurbished.  Now only 1 week later it reported another drive has failed and the drive replaced as predictive failure.  Looks suspicious, i.e. I am doubting the controller card.

    I think updating the firmware of the controller first, but not sure if I should replace the faulty drive first, i.e. If updating the firmware could cause table failure.

    Also, if I install OpenManage on a virtual machine (host is ESXi 4.1), OM sees the controller?

    Thank you!

    Start on our live image and export logs of the OMSA facility there.

  • Dell PowerEdge R710 with windows server 2003 R2 is not start windows in normal mode.

    Hi Sir,

    Dell PowerEdge R710 with windows server 2003 R2 is not start windows in normal mode after upgrading the RAM to 64 GB.

    Arrangement of RAM is made 4 our 16 GB of RAM on 2 channels. I get no error message about the RAM configuration. It is booting in safe mode but not start in normal mode, his hanging during windows startup.

    Please give me guide to solve this problem.

    I thank & regards

    Ramanantsoa D

    Thanks for the reply.

    My version of windows is 32-bit Windows server 2003 Enterprise Edition Service Pack 2.

    Although I have not tried switching/EAP, I will try that and get back to you.

    And again something I have an idea of the installation of windows server 2008 R2 Standard version on this server, it will support? Please let me know Chris.

    Thank you.

  • Install.VGZ fails in ESXi 4.1 install on a Dell Poweredge R710

    I have a cluster of ESXi 4.1 six-host running on Dell Poweredge R710.  They start from a USB key connected to an internal USB port.  I did at least 12-20 installs on the same hardware without problem.

    When I try to re - install on the single ISO ESXi 4.1 host via the iDRAC, the installation fails when loading install.vgz with the error message: "Booting: MBI = 0x000100c0, enter = 0x0040024a.

    I studied the two codes and the only suggestion that I get, it's that my hardware is not supported (specifically that my 32-bit processor is not supported).  I do not have a 32-bit processor, so I know that I can surrender.  I downloaded the CPU VMware ISO (file:///C:/Users/pguarco/Downloads/ compatibility, and my CPU meets all requirements.  Previous installation of ESXi host crashed for unknown reasons, where the re - install.  It is possible, that there is a hardware problem.  Any ideas on how to limit this problem?

    you are doing the right thing. only thing I could thing is bad ISO, (Please make sure that the checksum is correct). and the worst case material PE firmware update.

  • Can someone help me? I have a dell windows vista and the cd/dvd drive won't work correctly. Whenever I have insert a cd/dvd, it takes forever to read, and it ejects itself. Why?

    Can someone help me? I have a dell windows vista and the cd/dvd drive won't work correctly. Whenever I have insert a cd/dvd, it takes forever to read, and it ejects itself. Why?


    Detect and automatically fix problems of CD/DVD

    Please make all below even if you have done some before as it is often the set of operations which solves
    the question.

    Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
    Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
    This will refresh the default driver stack. Even if the reader does not appear to continue below.

    Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
    slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs - a Mr Fixit

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista

    When you insert a CD or a DVD, Windows Vista may not recognize the disc

    Your CD or DVD drive cannot read or write media - A Mr Fixit

    CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
    Drive CD - R or CD - RW Drive is not recognized as a recordable device

    Hardware devices not detected or not working - A Mr Fixit

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    Hope these helps.

    Rob - bicycle - Mark Twain said it is good.

  • Tecra S3 - need SATA / RAID driver for installing Windows XP Home edition

    I'm doing a new installation of windows xp on a Toshiba Tecra S3 model PTS30E-0DT03FDU
    Who knows where to find the RAID driver to load when you start the installation of xp?

    This model no longer appears in the driver download section.

    Of course, it is listed by download, but the older models are listed in the ARCHIVES.

    Please visit the download page for Toshiba - - once again and the slot type of product choose Archive.

    For Windows XP Home edition, you will find RAID driver for download.
    Can find you it?

  • Qosmio G30-175 - where to find RAID driver for Windows 7?

    I have a Toshiba Qosmio G30-175 and I need raid driver so I can install Windows 7. My operating system is XP and on Toshiba-home page, I can't find the driver.
    Can Enyboby please?



    Have you ever tried the Vista driver? If this isn't the case, you need to test, because most of the Vista drivers are also work on Windows 7. > support & downloads > download drivers

    I hope it will work for you, but you can give us feedback on this subject. I think it could be interesting to other people, too. ;)

    Good bye

  • It is possible to move my profile of the user of the c:, d: and reserving my main drive for the OS only

    I use windows Vista that is installed on drive C: (OS) year 80 gig hard drive plus I also drive D: (DATA) one new secondary 320 gig hard drive installed.  I want to use the system more effectively by saving and store my files on this hard drive automatically is it possible to move my profile of the user of the c:, d: and reserving my main drive for the OS only

    There are instructions of third party to do so, but this is not supported by MS and can cause problems

    Maybe redirect Documents libraries on the D drive

Maybe you are looking for