Similar Questions

• Path of VMdirect and Dell Poweredge T110 II

  No matter who got the e/s working on the Dell Poweredge T110 II DirectPath?  On the Summary tab, I have a warning indicating that the host hardware does not support the DirectPath of IO.  I have virtualization enabled in BIOS.  On the configuration tab I also have the error "Host does not support configuring passthrough" my processor is a intel Core I3-3220 3.3 Ghz.   If someone got it works with the latest BIOS?  I have to use USB external drives for storage of files and not facing one of the internal locations and just use the internal slots for my build of ESXI raids.  Any help in this would be appreciated.

  Thank you

  Stephen Bailey

  I discovered that my CPU does not support directpath i/o, so there is no hope in getting this work.  I found a work-around however to get a crossed USB device.

  While VMdirectpath i/o would be nice there is also a USB device transfer which is another way to allow direct communication with a hardware device to a guest operating system.  ESXI allows transfer USB Device (this can be done without vmdirect path).

  When I first tried this (I didn't know at the time that ESXI 5.0 did not support USB 3.0) device usb 3.0 had not passed through and I thought it was because of a misconfiguration of the vmdirect path.  I did some additional research after I discovered that my processor didn't support directpath and found documentation for transfer of USB device.  All I had to do was add the USB controller to my guest operating system configuration then added a "usb device" to the configuration of my guest operating system who found the name of the device is connected.  I was then able to add a USB 2.0 device and my guest what OS is very clear.

• Dell PowerEdge T110 II add on the video graphics card that works

  The system configuration:
  Dell PowerEdge T110 II
  BIOS 2.8.0
  RAM 2x8GB

  For many reasons (for example feeding bus PCI), it is difficult to install a Dell PowerEdge T110 II graphics card.  The ATI Radeon HD 5450 is a good choice for the Dell PowerEdge T110 II because if its (approximately 10W) low energy consumption.

  After trying several HD 5450 (listed below), a graphics card that works is a "VisionTek Radeon HD 5450 - graphics card - Radeon HD 5450 - 2 GB memory DDR3 - PCI Express 2.1 x 16'.

  Edit: Thanks to paikat for the following references, (see his assignment for the links, where to buy)...
  VisionTek manufacturer: 900356
  Reference Dell: A6173020

  This card works when the monitor is connected to the VGA/D-SUB/DB15 connector. I wasn't looking to connect to HDMI or DVI connectors.

  After you install this graphics card, passed the BIOS Setup:
  Integrated Devices > integrated video controller: enabled

  by saying:
  Integrated Devices > integrated video controller: Standard

  and allowed to move from "Standard" to "Distributed" so it now says:
  Integrated Devices > integrated video controller: distributed

  Note: Install the card with the monitor connected to the integrated video port / edge, change the BIOS to Distributed settings, restart the computer and then connect the monitor to the Discrete / distributed / video port to Add on.

  Here are the identifiers on the "VisionTek Radeon HD 5450 - graphics card - Radeon HD 5450 - 2 GB memory DDR3 - PCI Express 2.1 x 16'

  54502GBPC
  VT 5450 PCIe 2GB V/D/H
  VT-400746PC
  PCB #R81KLD-PJ3Z
  R71KLD
  R81KLD
  Version: 1.0
  G0850000-0351L002739CZA-0087
  SH6 94V-0
  E248779

  Here are some pictures of the 5450 VT from DELL:

  

  

  Other video cards that have been tested and work well in T110 II are:

  * XFX Radeon HD 5450 1 GB GDDR3 VGA/DVI/HDMI Low Profile PCI-Express graphics AMD card HD545XZQH2; HD-545 X-ZQH2
  Note there is another version of this card is ONXFX1PLS2 who has not tested.

  * EX-PX610GT-video JATON GeForce GT 610 2 GB 128 - Bit DDR3 PCI Express 2.0 x 16 HDCP ready low profile ready card video

  * Reference DELL SOUND H545H1G Radeon HD 5450 (Cedar) 1 GB memory DDR3 64 bit PCI Express 2.1 x 16

  I hope this can help others avoid the frustration when you try to install a video card in a Dell PowerEdge T110 II.

  SR2002

  I have read this thread and seen the suggestion of VisionTek, it also works with the card mother E3-1230V2?

  My guess is the Dell PowerEdge T110 II uses the same motherboard for various configurations of CPU, but this is only a guess.

  SR2002

  Also, are there better options eventually with the support of 12 DDR5 and directx?

  None that I know, but I've only tried a few cards. Please let us know if you find cards better than the VisionTek 900356

  SR2002

  I saw a thread suggesting ASUS GTX650-E-2GD5, someone at - he of the inputs on this card?

  I tried a GeForce GT 610 2 GB and it did not work.  Check the use of the GTX650-E-2GD5 (DPT) power and make sure that it is less than 25 watts (see below)

  Quick notes:

  1. the location of PCIe x 16 is actually a "full-size x 8 slot" (also known as an x 16 slot / x 8) and the video card needs to work in this type of accommodation.

  2. video card power (TDP) is a limiting factor. Technical guide Dell says "the system supports a maximum power of 25 W for all four cards PCIe.»  and said Dell owner's manual "ATTENTION: to ensure correct cooling, not more than two cards of four extension may have more than 15 W power consumption (maximum 25 W each), not to mention the integrated storage controller card."

  3 install the card with the monitor connected to the integrated video port / edge, change the built-in BIOS devices > on-board video controller 'Activated' / 'Standard' to 'Distributed', restart the computer and then connect the monitor to the Discrete / distributed / video port to Add on.

• My iMac was bought from China, it runs on 220V power supply, can it be moved to the United States working at 110 V?

  My iMac bought from China, he works with 220V power supply, can it be moved to the United States working at 110 V?

  Electrical and operating requirements

  Voltage: 100-240V AC

  Frequency: 50 Hz to 60 Hz, single phase

  Operating temperature: 50 ° to 95 ° F (10 ° to 35 ° C)

  Relative humidity: 5 to 95% without condensation

  Operating altitude: tested to 10,000 feet

  of https://www.apple.com/imac/specs/

• Server Tower Dell PowerEdge T110 II

  Hello

  For server Dell PowerEdge T110 II Tower

  If I choose

  Microsoft (r) Windows (r) Server 2008 x 64 R2 SP1 Standard Edition(5CAL), FI, S-Chinese [included in price]

  as the operating system, why then I an error like

  The version of Microsoft Windows Server 2008 R2 SP1Operating system was to have 40 GB or 80 GB maximum hard Drivepartition. To solve the problem, please use the links provided.

  choose which hard drive configuration?

  Kind regards

  Once you go to the section "Installation of boot (to Windows (r) OS only) Partition" and select 40 or 80 GB partition error you are referencing disappears.

  Let us know if you have any other questions.

• How vm can my Dell poweredge T110 run?

  How my Dell Poweredge T110 yourself run the specs are

  Processor Intel Xeon X 3450 (2.66 Ghz, 8 MB Cache, 95W TDP, Turbo, HT), DDR3 - 1333 Mhz

  Neniry 8GB (UDIMM rank double 2 x 4 GB) 1333 Mhz

  HD 1 x 250 GB 3 x 1 TB SATA

  1 x adapter Server Intel PRO 1000PT Port GbE, Cu, PCIe x 1

  a friend sayd I can run only 2 VM

  You can see one of the 2 CPU servers with 4 or 6 cores per processor. Similar to your T110 would be the T410. Add the second processor enough RAM and hardware raid controller. You can have SAS rather than SATA drives and you're better off with several discs smaller than smaller disks for better performance.

• Upgrade the graphics card and the power supply on a Pavilion p6823w - compatibility?

  Hello, everyone! After purchasing my HP not too long ago, I decided that I wanted to get updates for it. I intend to turn it into a computer game later, but for now I start small.

  I'm still a little wet behind the ears when it comes to computer hardware, so I would greatly appreciate any input on my decisions for improvement - especially if my power supply and graphics card will adapt and be compatible or if the marks are bad.

  Graphics card:

  PowerColor Radeon HD 6850 1 GB

  http://www.Newegg.com/product/product.aspx?item=N82E16814131374

  POWER SUPPLY:

  Corsair 500W CX500

  http://www.Newegg.com/product/product.aspx?item=N82E16817139027

  Here is the specific computer I have, for reference:

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=es&CC=ve&TaskID=120&prodSeriesId=...

  Thanks in advance!

  Hello

  I don't foresee any problems with your choices.

  Relatives on the slot PCI-E x 16 must be vacant.  Examine the characteristics of the motherboard.

  These "how-to" HP articles should be useful.

  TIP: Unlock and slide the optical drive forward before you remove and install the power supply. This helps facilitate the removal and installation of the power supply, but it is not mandatory.

• Dell PowerEdge T110 is not using all the Ram installed

  Hi, my name is Juan Marrero.  I work for bike Stop, Inc. in Puerto Rico.

  I've recently upgraded the processor and RAM to our PowerEdge T110 server.  Initially, there were only 4 GB of RAM.  Now he has installed 16GB but only 8 GB are usable.

  The processor is an Intel Xeon x 3430 and has been upgraded to an Intel Xeon x 3470.  No problem here.

  The specifications of the memories are: 4 GB DDR3 PC3 - 10600 ECC Unbuffered DIMM (4 of them)

  for a total of 16 GB of RAM.  I searched the internet and found nothing in the BIOS to not limit to 8 GB.

  Is there a limitation, no matter what the motherboard and processor say they can handle?

  I thought. The Foundation is limited to 8 GB:

  https://msdn.Microsoft.com/en-us/library/Windows/desktop/aa366778 (v = vs. 85) .aspx #physical_memory_limits_windows_server_2008_r2

• Dell PowerEdge 2900 RAID and drive down

  I have a Dell PowerEdge 2900 server. The primary transmission table has three drives and RAID 5. The system came this way, and it has been humming for quite a long time. Recently, one of the disks has deteriorated and the light on the drive flashes green and light amber. The light amber, I figured, it means that there is a problem with the drive and must be replaced. Then, I found a replacement on Amazon.com drive and installed (the drive is hot, but my cold started to be sure). I installed the drive, but keeps flashing green and amber light.

  I didn't know that I shouldn't have to replace the drive in this way, so I will now try to figure out what to do next. I hoped to reallocate the foreign disk so that I can use it, but my server always shows the reader, not having even if the new replacement drive is in the slot, now.

  I'm running PERC 5 / I integrated utility of Configuration Bios 1.04 - 019 a

  I started the server and you press CTRL-R. I've highlighted the controller and press the F2 key, what is operations. When the operations window opens, there are three menu items:

  Create new VD
  Zero Config reset
  Foreign config

  The only thing that I am allowed to do in this menu is to reset the configuration. I can't move my cursor upwards or downwards for one of the other choice of two menu.

  Scroll when the virtual disk and he discovers, it still shows the first two discs and a lack.

  When I press CTRL + N to display the next screen, I see a player listed as failed.

  How can I rebuild my RAID with this new drive? If I can't do it, what is the best way to remove the RAID and start over? If I delete the RAID and do it again (and if my replacement drive is indeed well), how can I make sure that my server not to see it, not having so that I can start using it?

  Alternating flashing green/orange means that the disc is in a status of predictive failure. What OS is running system? If you hotswap drive next failure they may possibly other issues table because the drive was online and participating in the table with errors on the disk. The adequate alternative method is to use our software Openmanage Server Administrator to run a consistency check on the table and then the drive offline. Once this has been done you can then swap the drive. It seems that in your case, that the new drive had bad data copied on it and it made a predictive failure as well. We want to do is run our hard drive diagnostics and test drives in the system.

  http://downloads.Dell.com/FOLDER01456532M/1/Dell-onlinediags-Win32-2.30.0.70.exe

  Install and run the GUI version in the start menu. In the left pane select the PERC 5 and then in the lower right pane select quick test and then to run tests.

• RAID and Dell PowerEdge T110 ESXi 5.0 configuration

  I just do a fresh install of ESXi 5.0 on a Dell server, which has 2 x 250 GB HDDs in RAID 1 configuration. However, in the management of ESXi I am presented with 2 drive 250 GB each, which should be visible as a single drive. This is something that Windows 2008, on bare metal, took care, and what should I do with ESXi to fix this? I just need to reboot the server and enter the RAID configuration? I need to be careful because I don't want to lose any existing data. Thank you.

  Welcome to the community,

  ESXi supports only RAID controllers that are transparently logical drives to the operating system. In your case, it seems that you are using a RAID controller for software that requires additional drivers for the RAID of the operating system, which are not available for ESXi.

  André

• SSD & DELL POWEREDGE T110

  Hello

  I would like to ask questions about the meaning of installing an SSD in the server Dell Power Edge T110. As I understand it, the server runs on the SATA1 interface. What SSD do you recommend?

  Concerning

  mlik1987

  Hello.

  Unfortunately, the SSD is not supported on the server of T110. You are limited to only hard drives SAS and SATA

• PowerEdge T110 II and SAS network

  Hello

  I have an old T110 II server for 2 years and I want to install a double extra port card Go like Broadcom Dell 5720 for installation of Hyper-V and a Perc H310 card that can be easily found in my country.  But neither one is listed for compatibility with this server.  It is possible to do or not?

  In addition, when I researched H310 it is not entered as a single integrated H310 different from that I intend to buy the Dell site which appears as a regular PCI card! Are they different models for H310?

  Barebone Dell servers here are advirtised to work with SAS disks, but are sold without controller Perc... :-)

  Any help or suggestion will be apreciated. Thank you

  Cgales,

  Unfortunately the H310 will not work in the T110 II. This is due to the designed H310 for use specifically in the most recent 12 generation servers. The T110, supported hardware raid controller would be the H200, or with the S300 software raid solution.

  The H310 has another model, which is designed for use in the model of blade servers.

  Let me know if this helps answer your question.

• Win 7 (64) "sleep" and "hibernate": power supply for USB devices

  Hello: Just ordered a new PC with Win 7 Ultimate (64) and I need advice on creating a power plan. I learned the hard way with Vista Ultimate (32) that "sleep" and "hibernate" cuts the power of USB, such as UPS devices with battery backup. It was a bad function, since my UPS runs the software that automatically stops the system if necessary. However, when the Vista computer went to 'sleep', the connection to the ASI has been cut, while the UPS is no longer communicates with the central unit. Therefore, if stopped and directed were needed when the system is idle / "asleep", UPS might not make it. The only solution I could find was to create a custom power plan that stops the CPU (and that only updates the display on screensaver for X minutes and then turns off the screen). Obviously a question of wear for the system, being never in mode 'sleep'. Windows 7 behaves similarly, depriving USB power in "sleep" or "hibernate"? Will I need to apply the same workaround? Please notify. Thank you! daledoc1

  Right click on the USB device device manager concerned and select properties then power management and clear the option to Turn off energy-saving and activate the option to wake up from its sleep.

• New Nividia Grapics card and new power supply which will work on 500-199

  I want to run most of the high quality games! My budget is $ 200 thank you!

  The 550W would be insufficient for the HD 6970 selected thread locking in the other post... to clarify.

  http://h30434.www3.HP.com/T5/desktop-hardware/will-this-work/TD-p/4474108

• Dell PowerEdge T110 with internal RD1000

  Anyone know why the server backup doesn't let you choose the RD1000 as a location for the backup on. It is not yet listed. I see it in the list of files in the drive 'e '. but will not appear in the backup software.

  Hello ttcmartin,

  What is the operating system that you are running?  If it is windows 2008, 2008R2, or 2012, you will need to use a 3rd party software backup to get the player seen.  Since windows 2008 if you want to use a tape as your backup target device you must either get Microsoft DPM or a 3rd party backup software.

  Please let us know if you have any other questions.