Dell PowerEdge T610 (memory upgrade)

Similar Questions

• Dell PowerEdge R710 memory upgrade 16 GB (4x4Go) for 72GO with more than 64 GB (8x8Go)

  Hi all

  My Dell PowerEdge R710 is seen 16 GB (4x4Go) now and would like to add 64 GB (8x8Go), it will be total 72GB. Please help me add memory into the slot on the right. Can I do the following as below

  A1/B1 > 8 GB

  A2/B2 > 8 GB

  A3/B3 > 8 GB

  A4/B4 > 8 GB

  A5/B5 > 4 GB

  A6/B6 > 4 GB

  Thanks Robert, I already bought 64 GB (8x8Go) and would like to add to my current server which is running 16 GB (4x4Go). So, please show me how.

  Thank you

  Binh Kien

• Dell PowerEdge T310 Memory Upgrade configuration

  Hi all

  Currently I have a T310 with 2 x 4 GB memory

  Information about the DIMM:

  (Hynix 4 GB PC3-12800 DDR3 - 1600 MHz ECC Registered CL11 240 - Pin DIMM memory rank double Module Mfr P/N HMT351R7CFR8C-PB)

  I intend to add with a total of 6x4Go = 24GB 4x4GB

  This new configuration of memory will be supported?

  Thanks for the reply

  See more info on the server below;

  Server has 1 CPU (Xeon x 3430 @ 2.40 Ghz)

  Memory information: Ok

  Attributes of the bars of memory

  Attributes; Memory Matrix 1
  Location; Motherboard or motherboard
  Use; System memory
  Power installed; 8192 MB
  Maximum capacity; 32768 MB
  Available slots; 6
  Locations used; 2
  The ECC type; Multibit ECC

  Total of bars of memory

  Attributes; Value
  Total installed capacity; 8192 MB
  Total available power to the BONE; 8192 MB
  Total maximum capacity; 32768 MB

  Table 1 of the memory details

  Status; Name of the connector; Type; Size
  OK; DIMM_A1; DDR3 - synchronous registered (buffered); 4096 MB
  OK; DIMM_A2; DDR3 - synchronous registered (buffered); 4096 MB
  Unknown; DIMM_A3; [Not busy];
  Unknown; DIMM_A4; [Not busy];
  Unknown; DIMM_A5; [Not busy];
  Unknown; DIMM_A6; [Not busy];

  Device memory information: Ok

  BRIEF on connector: DIMM_A1

  Attributes; Values
  Situation; OK
  Device name: DIMM_A1
  Size; 4096 MB
  Type; Synchronous DDR3 registered (buffer)
  Speed; 0.63 ns
  Failures; None

  Device memory information: Ok

  BRIEF on connector: DIMM_A2

  Attributes; Values
  Situation; OK
  Device name: DIMM_A2
  Size; 4096 MB
  Type; Synchronous DDR3 registered (buffer)
  Speed; 0.63 ns
  Failures; None

  Components (FRU) Information System

  Device; Serial number; REF.; Revision; Reference of the manufacturer; Date of manufacture
  System Planar (BMC); CN1374008602B7; 02P9X9; A00; DELL; Mon Aug 09 04:00 2010
  1 power supply (PS 1); CN1797208E0NQR; 0N884K; A00; DELL; Mon 16 Aug 10:25 2010
  DIMM_A1; 4B55A111; HMT351R7CFR8C-PB; S/O; Hynix Semiconductor (00AD04B380AD); Mon Apr 09 16:00 2012
  DIMM_A2; 4B15A14C; HMT351R7CFR8C-PB; S/O; Hynix Semiconductor (00AD04B380AD); Mon Apr 09 16:00 2012

  You can always memory of control similar to the one you already based on the part number. Also check the link below for memory other compatible Dell:

  http://Accessories.us.Dell.com/SNA/category.aspx?category_id=8136&c=us&l=en&s=BSD&CS=04&mfgpid=203788

• configuration dell poweredge t610

  Hi all

  I hope you guys can help me with the following.

  I have this server in the office: dell poweredge t610.

  Configured with raid 5.

  Two of your hard drive has failed, so I replaced the. After the replacement, used windows. Boot. I installed a fresh installation of windows 2008, after a reboot once the installation is complete. I know that the following message:

  Uncompressing Linux... ok, booting the kernel.

  System initialization, please wait...

  To start replication, please insert your disk replication.

  Replication will begin once the system has started.

  I don't have a disk of replication.

  How can I solve this?

  "Missing only the drivers for interruption of system controller. can we all now who are these? »

  You must install the chipset:

  ftp.dell.com/.../INTEL_5500-5520-CHIPSET-SOFT_A03_R295077.exe

  "Also the program called to control the raids of the web?

  It's called OpenManage Server Administrator:

  ftp.dell.com/.../OM-SrvAdmin-Dell-Web-WIN-7.3.0-350_A00.exe

• Dell PowerEdge T610 and ESXi 4.0 integrated

  Hello world

  My company has just purchased a new Dell PowerEdge T610 as our first server VM. They bought exactly the same configuration that Dell recommended for virtualization, which came with an option to get the ESXi 4.0 embedded. By charging Dell about $ 2000 for the premium service when buying the ESXi, society has decided that we will install ESXi embedded ourselves (on a SD card or USB key).

  And so the task was given to me

  Now, here's the problem I encounter. I downloaded the ESXi 4.0 installable with customization of Dell, and it seems to work fine on a USB key. But I can't find the instructions on how to actually install the embedded and non ESXi 4.0 installable version. I have ESXi 4.0 installable on the stick, but how do I get the embedded installed on it (or SD card). I see that people have done with ESXi 3.5, but all it seems to be there on the net about installing ESXi embedded yourself is only how to install the installable on the USB. It's a stupid, and built-in question is nothing more then a installable on a USB?

  Sorry for a newbie question...

  Thank you very much in advance!

  André

  integrated, installable should be the same, the difference is that with the integrated option you would not need to install

  Jose Ruelas B

  http://aservir.WordPress.com

• Dell PowerEdge R510 memory Conmfiguration

  Greetings,

  I have a Dell PowerEdge R510 with a SINGLE processor that currently has 16 GB of slots of RAM installed A1 - A4 are all filled with 4 GB memory modules. My questions are the following:

  1. Am I able to, another 8 GB or memory?
  2. Is only to have a CPU a problems with filling more memory?

  Think I found my answer here:

  en.Community.Dell.com/.../19645918

• Upgrade memory Dell PowerEdge T610?

  Hi, I have a T610 with 8 GB (4 x 2G 2Rx8 PC3-8500R). I would put more than 8 GB, (4 x PC3-10600R 2 G 2Rx8). Works? What is the best setting?

  [of]

  Hello.

  How many processors you have installed?  There are several guidelines of population of memory including memory on all channels balanced for optimal performance.

  For a single processor, you will only be able to use six modules because of this limitation, where:

  A1, A4, A2A5, A3A6: 2GB with capacity of 12 GB total memory

  For the two processors:

  A1A4, A2A5 & B1B4, B2B5: 2GB gives the ability of memory of 16 GB. I advise to use strips of memory ability higher such as 4 GB, 8 GB, or even 16 GB because they offer memory expansion more and robust.

• Dell inspiron 15R Memory Upgrade N5110

  Hello

  I have a dell inspiron N5110, and I plan on upgrading the RAM modules, which are estimated at 1333hz. I would like to know if the motherboard can support modules of RAM at higher frequencies, if so, how much of a gain of performance can I expect.

  Any help will be greatly appreciated.

  Thanks in advance.

  Fastest modules may work but will not increase the speed - 1333 MHz is the speed of memory limit in this model.

• The RAID on the PowerEdge T610 controller upgrade

  This system came with a SAS6/iR controller and after the installation of Server R2 2012 and with 32 GB of RAM it's on all fours, probably because we use software RAID 5. I want to upgrade RAID controller so that I can use hardware RAID 5. What controllers are compatible with the T610? I know that the H710 is eligible, but what about the H710P and the H810? We have a bottom of basket that holds 8 discs. Do we need anything else? I see that some people needed cables as well.

  PERC 6 / i and the H700 are validated for the T610. The Hx10 are 12 generation servers (like T620, T610 is 11G). H8x0 controllers are for external storage.

  Main differences between H700 or PERC 6:

  PERC 6 is 3Gbps, max disk 2 TB, 256 MB cache
  PERC H700 is cache cache/memory NVRAM 6Gpbs, TB + 2 disks, 512 MB or 1 GB

• Dell Dimension 8200 Memory Upgrade after upgrade the processor

  Hello

  I have a Dell Dimension 8200 (shipping date is 01/05/2002) which came with a FSB of 400. I've recently updated the its origianl 1.8 GHz a 2.4 GHz processor.  I understand that the 8200 with a FSB of 400 can use 800-40ns or 800-45ns memory sticks (I think that mine came with 800-45).  I intend to upgrade memory 1 GB to 4 X 512 (2GB), I installed (4 X 256).  My question is when I went to buy the 4 X 512 memory, said the pub, it could be used in a 8200 with a 2.1 GHz CPU or less.  I have a 2.4 GHz chip. Is that going to be a problem?

  Rbatleman,

  Great question!  When the Dimension 8200 was released the processor speed max was 2.1 ghz (probably why the memory you were viewing had this label).   We have updated later to the processor 2.4 ghz when it was available.  The two units came with the PC800-45 (400 mhz) memory, you should run into any problems with this memory.  Keep in mind the system supports only the RIMM modules that contain devices memory of 4, 8 or 16.  I hope this helps!

  -Andrew

• PowerEdge T310 - Memory upgrade Question

  I'm trying to upgrade a T310 to 16 GB of memory. It has a processor Xeon 3430 2.4 GHz with 8 GB of memory installed factory - four 2 GB 1Rx8 DIMM. I want to spend a total of 16 GB so tried to add two 2RX8 4G memory ECC low voltage according to the recommendations of upgrade parts from Dell. The server will not start. I looked through the forum and Dell manuals to try to understand this. Can I switch to 16 GB with 8 GB of memory installed in existing plant, or do I have to replace the existing memory with four 4 GB RDIMMs? Thank you! Bev S

  The DIMMs you listed are actually UDIMM, why upgrade Rdimms do not work for you. Now with those being UDIMM the T310 only supports using total 4 DIMM. In order to reach 16, you will need to replace the existing 2 GB UDIMM with 4 x 4 GB UDIMM.   Which is the same as using just the 2 8 GB Rdimms only to hit the total of 16 GB you are looking for.

• Dell Dimension B110: Memory upgrade problem

  I have problems with my upgrade memory. I bought a few 1GBX2 2 GB of memory, and I know that my computer can take because I had done the research before I bought the memory. But with I put memory he doesn't recognize her, it's like id I have no memory what so ever in the machine. I was wondering if there was something that I'm supposed to do or change to get the ram to read. It takes PC-3200 RAM type.

  And another thing... I have 512 MB of RAM, but he acknowledges as 504 MB of RAM... Any reason why it's like that?

  Specifications of the computer:

  Microsoft Windows XP
  Professional
  Version 2002
  Service Pack 3

  Intel [R]
  Celeron (R) CPU 2.53 GHz
  512 MB of RAM

  
  

• Dell Optiplex GX520 Memory Upgrade

  Hello, I install 4 GB of memory on Dell Optiplex GX520.

  Of memory can what type I install?

  PC2-4200 is not fast enough for some of the processors supported FSB.

  Faster RAM doesn't hurt anything, but it may not work at the fastest speed, unless the processor is running at top speed for the FSB also.

  • PC2-4200 = 533 MHz clock
  • PC2-5300 = 667 MHz clock
  • PC2-6400 = 800 MHz clock

  

• Dell XPS 8500 - memory upgrade problems

  I bought a Dell XPS 8500 nine a couple of years.  It came with 8 GB of memory (2-4 GB DDR 3 1600).  Recently, I picked up two sticks of 8 GB, DDR-3 new, 1600.  In total, this should give me 24 GB of memory.

  Currently, housing 1 and 3 are using 4 GB sticks and slot 4 has a key of 8 GB.  If I try to stick the other stick in slot 2, the system does not start.  I assumed it was because a bad stick, so I went back to the store and I replaced it, but the problem persists.  I can get a total of 16 GB, which is recognized in the system.  According to Dell, and Crucial, this system should support up to 32 GB.

  This system only supports the memory to some total amounts, as the 16/08/32?  I checked my BIOS is updated as well.

  I'd appreciate any comments on it.  Thank you!

  If you consult the technical data sheet, the only supported RAM configs are: 2, 4, 8, 12, 16, 32 GB.

  Read this.

  EDIT: And modules are best installed in pairs, so 2 x 4 GB + 1x8GB is not an optimal config.

• Reference Dell 8300 & 4600 memory upgrade?

  You can put 2 x 2 GB memory cards in to 4 slots for 4 gb (s) in the 8300 & 4600? Or are you using 4 x 1 GB cards? and why?  Thank you