Dell Precision 670, ESX (i) failed with... CPUID...

Similar Questions

• Windows 7 works with the Dell Precision 670 computer?

  I have a Dell Precision 670 workstation. It came with Windows xp x 64. I later upgraded to Windows Vista Ultimate x 64. The only problem I had at the time is that the host SCSI controller is not recognized by Vista. I used the XP x 64 drivers for the scsi controller and worked well. I want to upgrade my Vista x 64 to Windows 7 x 64. Everything else does? Doing a job? The Windows 7 Upgrade Advisor reports the controller scsi HD as an unknown (just under the name Vista Upgrade Advisor).

  The HD controller is an embedded controller the Adaptec SCSI HostRaid (Ultra320). I was not able to determine the model # of the controller.

  A representative of Micorsoft with what I discussed this said as a general rule, if your hardware works with Vista service pack 1, you're usually good to go.

  On the Dell website, it lists the 690 as working with Windows 7. It is a similar job, but I can't say with certainty how similar.

  I saw him last night. I'll look over it.

  Dave.

• Dell Precision 670 workstation

  Hello

  Please,

  What is the maximum quantity allowed memory per slot for the Dell Precision 670 Workstation?

  Thank you very much.

  Jaime.

  The registered ECC PC2 - 3200 DDR2 SDRAM DIMM. Supports Dual Channel DDR.

  Must install 2x4gb front row double two slots

  and then 4x2GB single row only.

  800 MHz FSB, Intel E7525 Chipset

• How to install ESXi 4.1 on a Dell Precision 670

  I have ESXi 4.1 of loading the CD successfully (I get around the problem of limit CPUID).

  When it gets to the stage of the installation, it will fail with the message "could not find a device supported to write the image.

  System Specs:

  Reference Dell 670

  Two-processor Xeon 3.2 ghz Irwindale 64 processors quadricoeurs

  2 GB memory

  A 72 GB SCSI HDD (currently formatted NTFS so is still a factor)

  BIOS is A07

  Any help would be appreciated.

  As written in the previous post try to install on a USB key.

  But VMs must leave a hard drive connected to a supported adapter.

  If SCSI does not work, try again with IDE drives.

  See also in white box configurations:

  http://www.VM-help.com

  http://ultimatewhitebox.com

  PS: 2 GB are a very small amount of memory to virtualize virtual machines...

  André

• Dell precision 670 windows 7 64 bit running

  Hi can someone tell me how to change the operating system for the precision 670 to dell for windows 7 64. do we have to change the settings on the Setup? Please

  Thank you

  Changing what operating system? You can not alter the operating system or install 32to 64-bit without a cleaning. You will lose everything. 64-bit requires a processor 64-bit capable. Check your system information.

• Dell Precision 390 doesn't start with Bios pin in Place

  I recently acquired my nieces computer Dell Precision 390 and was trying to upgrade to Windows 7. When I opened upward, I noticed that the pin of the Bios was only placed on one of the pins instead of two of them as shown in the maintenance manual.

  After the replacement of the Bios pin on the appropriate setting, the computer will not start and has no effect when you press the Start button.

  I replaced the pin of the Bios to the place where I found it originally, and the end started computer. What gives here? Why didn't he start if I place the PIN Bios exactly where it is supposed to be?

  Does anyone have answers or suggestions? Thank you!

  His work EXACTLY as designed.
  

  Clear CMOS/NVRAM memory; 390

  By rider:

  The computer must be disconnected from the power outlet to clear the CMOS setting.

  Remove the cover from the computer.
  Locate the RTCRST jumper on the system board.
  Remove the CAP from the single-axis and onto the two pins and wait 3-5 seconds.
  Replace the cap on the single PIN.
  Replace the computer cover.
  Plug the computer and peripherals to their electrical outlets and turn them on.

• Workstation Dell Precision T7400 will not power with ATI Radeon 5970 installed

  Hello

  I had my dream, the monster bi - GPU ATI Radeon 5970 video card and installed in my T7400 but the system will not start, all I get is a fast fan rotation and a kind of sounds from food, a bit like "Brrrnt, click on" led me to believe that the power supply could not handle my video card.

  The video card requires an 8pin and 6-pin power plug. When I plug the 8-pin and 6-pin and turn on the computer, is a no-go as shown above. When only the power plug 6-pin I plugged the PC sounds like it will start, the power of fans but no display as I expect.

  I tried this video card into the two PCI-Express slots with the same failure as a result. The computer works fine with the Nvidia Quadro 3700 in it... using a 6 power connector pins.

  I got the ATI Radeon HD 5970 video card in a store of the local computer and it had tested ($15) because I didn't test it in a spare computer and video card passed with flying colors...

  That's why I thought my 1000 Watt power supply was a problem, so as a bet, I ordered a replacement off eBay and received a sweater to work more the wiring harness and completely replaced the two who has a job to say the least! Have you tried to replace the wire bundle? a lot of work...

  I got it all back together, crossed my fingers and prayed and tried again and the same thing... NO LUCK... I put the graphic card Nvidia Quadro 3700 back in and the system of power like a charm.

  What on earth could it be the cause for it? I REALLY want to get this video card works in this system.

  I even tried a bios update and carefully watched the card mother and everything that I could to see if there's... nothing exploded capacitors...

  Please HELP - I want to get my game...

  Wesley

  I think I found the solution and I would like to mention it here to help others if they get him...

  A: the power of Dell for the T7400 was designed to produce five rails 12 volts @ 18 AMPS each and the video card requires approximately 45 to 50 amps to work properly. Video cables (one with a 8 pin) and 6-pin on the harness even seems to only provide amps 18 or more and the computer will not power because power protection circuit sees too many amps being requested by a 'rail' and turns off immediately...

  I went to electronics of FRY in San Jose and bought a few cards that helped divide the current between different sources, such as the cables of the hard drive and video.

  B: I have a small battery backup power unit and my T7400 was plugged into the saved game... When I got the video card to work, he could make a beep loud and after minutes cutting my T7400 due to the mainstream power support... I plugged the computer into a 'surge protector' but not battery backed up to the slot and since then had no problems...

  Now after several tests including FurMark, my graphics card stress works very well in this system... This is due to an unfortunate design in the T7400 power supply and wiring... Now that I have this solved, I hope that someone else can benefit...

  Get an adapter like this one, it allows to separate the power sources for the 8 power connector pin and use the PIN 6 original which is connected to the Dell printer condition 8 pin adapter, for the 6-pin slot... hope that makes sense... by trial and error, you got it right!

  I had one like this:

• x 8 connection distance MXI causes conflicts with my on my Dell Precision T3600 PCI slot

  Hi all

  The easiest to say is that I am migrating from a x 4 MXI explicit connection to an x 8 MXI express connection and when I do I get an error on the motherboard which is unable to load the single PCI slot.

  Error in WIn7 64 bit Device Manager reports a yellow exclamation point

  Device "Intel (r) 82801 PCI Bridge - 244 properties"

  The error listed in the device status box: "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Unfortunately, I need this slot machine to run a card calendar to conjucton with PXI hardware. There is no anomaly when I used the x 4 connections with virtually the same loadout except for one Exchange a PXI-5122 (x 4 config) to SMU 5122 (x 8 config).

  If I leave the MXI PCIe card in but do not connect to chassis PCI slot SMU (and the fine card appear.)

  If I remove the PCI card into the slot, the error still occurs.

  I swapped the x 8 card and NVidia graphics card without success (the 16 x only two slots).

  I photographed the reader and removed the H310 Dell PERC RAID card and charged the RAID array RAID integrated Intel C600 and still no change.

  I have updated BIOS to A07 to latest A08.

  I updated the Intel Chipset at the latest on the Dell Web site.

  I guess that I just wonder at this point if someone is able to run a x 8 MXI express at SMU with a Dell Precision T3600, T5600 or a T7600 chassis.

  PC - Dell Precision T3600

  Windows 7 Enterprise 64-bit SP1

  3.2 GHz Xeon 6 core (E5-1650) w 16 GB of DDR3 memory

  Reference Dell PERC Raid (x 8 PCIe) H310 / C600 onboard Intel RAID

  Nidia Quadro 600

  2 x 1 TB SATA drive (mirrored)

  SMU Rack - OR 1082

  Slot 1 - SMU - 8381

  Slot 2 - OR SMU 5122

  Slot 3 - NOR SMU 5442

  Housing 4 - OR 4 to 6 TB RAID NI 8262 x MXIe

  Housing 5 - PXI 6733

  Housing 6 - PXI 6733

  NI MAX report is attached as a text file.

  After much work by NI Applications Engineer Kyle K, this problem has been resolved.

  I'll post the solution to this PC dependent problem here, just in case it will help others in a similar situation.

  It seems that Dell sometimes uses one default BIOS quite restrictive on the number of PCI bus in these (and other). By allowing several PCI bus, you will be able to list all the devices in the sacrifice of some memory available for OS 32 bit running on 4 GB of RAM. No problem for me because I'm under 64 bit OS.

  Congratulations to Kyle even if he has not posted here yet for him give real congratulations.

  Greg

• Card PCI-6259 is compatible with the Dell Precision 390?

  Hi all

  I need help in answering this question.  I want to buy a better computer for my data PCI-6259 acquisition card.  I tried to search to see if the card is compatible with the PC and there's previous numbers with this set-up before other users.  Do you have a link to the list of the DAQ cards with tested PC configurations?  I want to just make sure that when I buy the computer, everything will work without problem because I only have one shot at this.

  Thanks to all in advance.

  Kind regards

  justdomechanicalengineering

  Hello

  We do not have a link to specific DAQ board/PC pairings, but the specifications for the Dell Precision 360 indicate that she has three ports PCI 5V which must be compatible with your PCI-6259.

  Best,

  Dan Nelson

  Technical sales engineer

• Dell Precision 7710 with NVIDIA Quadro M5000M problems with 3D WPF content

  I have a

  Dell Precision 7710

  6920HQ-i7 CPU @ 2.9 GHz

  32 GB of Ram

  Windows 7 Pro Sp1

  NVIDIA Quadro M5000M 369.49 driver version

  I bought an upgrade for my

  M6700 Precision

  Our company has developed and uses software that uses WPF to render 3D content in a XBAP in Internet Explorer.  When I try to use it on the 7710, 3D content flickers when it is redrawn, makes it almost unusable.  The stats we can get our application, we can see that time of update for refreshment / current is about 45ms, while on most of the other PC, even those using the integrated Intel graphics card, typically 12ms.

  We used this software on a large number of PC without feeling anything as bad, which is obviously quite disappointing because the laptop should be able to view we want to hassle.

  As far as I can tell all our drivers for everything on this laptop are up-to-date.

  We tried using the NVIDIA Control Panel to force the laptop to use the High Performance Nvidia Quadro rather than the graphics card integrated card and it seems to be made while we were able to do, it shows the icon in the taskbar notification and which showed that IE was using the Nvidia.

  I tried tweaking pretty much all other settings I can think / see.

  I tried to use the Dell Precision optimizer to select different profiles with no luck.  The Dell Precision optimizer seems not really demonstrate the use of the GPU processor or any other stats to see with the GPU, which seems odd to me.

  I ran Diagnostics on the laptop available on the Dell support site.

  I searched the net and found a few examples of problems with Nvidia and WPF cards, but none of these things that we found seems to apply to our application.  We have desktop computers at the office where he works well with other Nvidia cards / best of all.

  In addition, the fan on the 7710 will quite difficult sometimes - hard that I expect.  I tweaked the power settings to move less, but it always seems to run the fan more that I think it should / would appear on my M6700 - or maybe it's just a fan of stronger.

  So I wonder:

  If anyone out there has experienced something similar?  If so, any suggestions on how to fix or things to try would be greatly appreciated.

  Thank you

  We solved the problem by making changes in our application software.  We still don't seem to be able to reach the same FPS as for the other GPU, which should be similar, but we're working on that also.  Perhaps because we are trying to run the application at 4K.  If anyone has a similar laptop and can provide details on the 3D graphics performance using any software comparative analysis, it would be great if they could share for comparison.

• Dell Precision T3600 problem with feedback headphones

  Hi all

  I recently acquired a new Dell Precision T3600 (in January 2013). However, I got a problem with your comments when I insert earphones into the headphone jack on the front of the office. The noise can be described as a sizzling/humming noise that is loud to the point that it is too distracting to listen to the audio through it. You can hear in the headphones, however, comments are always present and distracting. I also used several different headphones to exclude that, as the problem.

  I'd love to hear from others if it is a common problem with this system. I've read elsewhere that it could be a problem with the graphics card from NVIDIA, but I'm not sure.

  Kind regards

  Shaun.

  Some components of the system:

  -Intel Xeon CPU E5-1603

  -OS Windows 7

  -Graphics NVIDIA NVS 300

  This should answer your question.

  http://en.community.Dell.com/support-forums/desktop/f/3513/t/19466580.aspx

  I just got a T3600 and will contact them to get the front i/o Panel replaced.

• Dell Precision M90 recently upgraded to x 64 Win7 can not get correct graphics, stuck with the Standard VGA Graphics Adapter Card

  I have a Dell Precision M90 laptop and recently upgraded to Vista 32 bit to 64 bit Windows 7.  Everything worked perfectly, except for my display drivers.  Windows 7 installed a driver called Standard VGA Graphics Adapter.  This driver has a very low resolutions only and cannot deal with games or same Aero.

  I had an experience with updated video drivers with Vista.  My graphics card is a NVIDIA Quadro FX 2500 M.  When I had Vista there is no Vista compatible driver for this card, so I used the Geforce 7900GTX driver (which is inspired by the FX 2500 M) and it worked fine.  Of course, the Quadro FX 2500 M doesn't have a driver compatible windows 7.

  I downloaded the driver for the 64 - bit Windows 7 Geforce 7 series so I could upgrade and use, however when I used the NVIDIA installer it says that my computer has no compatible hardware for this driver (I tried to install it in Vista compatibility as well).  I tried to force the upgrade by using the option "have disk" and choosing the .inf directly file.  This did not always and said that he could not work because "the selected driver for this device does not support this version of Windows" even if it is the version of Windows 7.

  I also tried to start my computer in safe mode, uninstall the VGA Standard driver and then install the driver NVIDIA, but it does not work either.

  Sorry for the long post, I just wanted to add as much information as possible I hope to solve this problem.  Thank you for taking a look and thanks for your suggestions!

  Fixed!  Finally!  Dell.com took the pilot... but the link that they had posted on the page of Precision M90 was mislabeled.  I tried another way, found the good pilot, and got, it works.  Solved the days and days of frusturation.

• If I want to use an external monitor of ranking on dell precision 5000 or Hp zbook (equipped both of usb3 and thunderbolt 3) this piece of harware would work with SG?

  If I want to use an external monitor of ranking on dell precision 5000 or Hp zbook (equipped both of usb3 and thunderbolt 3) this piece of harware would work with SG? My monitor is a scientist of Flanders HDSDI LM-2460W. I know blackmagic has a few options but the last time I checked, he has not worked with SG. Anyone know?

  I think Sg works more easily with an output of your video card... I run two monitors style DVI outputs, but he could use the HDMI connections too I think. The tab Setup (wrench) go you and activate a second monitor and... it's a unique method instead... use the lines where she asks location information to 'say' Sg where the upper-left pixel of your second monitor (program or viewing) is your monitor 'system '.

  I had two 1920 x 1080 monitors, stacked vertically, OS/UI on the bottom, "programs" or reading on the upper monitor.

  So, this upper-left pixel of my 2nd monitor is a negative number for 'up' and zero to indicate the two pixels top left "even".

  It is-1080 for the "vertical" number... it's the height of my 2nd screen and it is negative, because it is above the main screen.

  It is 0 for the horizontal number. Yes, they are stacked.

  Now, if I had a monitor/program play to the left of my OS/UI screen, it would be...

  Vertical number 0, as relatively, they have the same 'height ';

  Horizontal number of-1920, that reading is on the left.

  Reading right... Vertical would be 0 and horizontal a positive number of 1920 (width of the primary monitor).

  Neil

• Dell Precision M4700 (Windows 7 pro) starts not once configured with UEFI and Secure Boot

  To all those who can help you:

  I got a Dell Precision M4700 and I update bios A05. I was intending to move to Windows 8. Everything was fine and the bios update was successful. I started the new bios under Windows 7 Professional (base OS) factory-installed and was very good.

  However, I can't get into the bios (not even see the POST from Dell or Logo) after I activate the UEFI and Secure Boot.This before I update to Windows 8 Pro. Now I'm stuck with a blank screen (same LCD not lit) and nothing to start. It's like a dead PC.

  Help, please. Is that what I can do or should I contact Dell Support for repair?

  Thank you

  I fixed it!  Just removed the CMOS battery, the BIOS got reset back to factory default.  So I did:

  (1) remove the battery

  (2) press the power button to the case of ground

  (3) remove the lower panel

  (4) disconnect the CMOS battery (it's tedious)

  (5) I hit the power button for some time (30 s) to clear the capacitors or something else, it was my theory, but I doubt it's necessary

  (6) use it to all back to the start

  When I turned it on it turns on and turns off several times before finally stay standing and I was then able to enter the BIOS and all the settings have been restored to factory default.  I am new to Windows 7 on my machine so I'll repeat the process, this time without disabling the legacy option roms!

  Here is the disassembly for precision M6700 and M4700 instruction manual if anyone needs:

  http://support.euro.Dell.com/support/eDOCS/systems/wsm6700/en/OM/om_en.PDF

  http://support.Dell.com/support/eDOCS/systems/wsm4700/en/OM/om_en.PDF

  I was talking about the Dell support problem and the guy said he would talk to his superior and see if something needs to be done, so I guess we'll see if something happens.

  I hope it works for you!

  Ben

• Inspiron 5749: BIOS update fails with the error 'Dell id does not match ".

  Hello

  I'm trying to update the BIOS of the Laptop Inspiron 5749. I downloaded the update file 3443A 07. EXE from Dell support website, where the update is supposed to be compatible with my system:

  -Dell Inspiron 3443/3543/5749 system BIOS;

  -Version A07.

  -Pull out the date 18 November 2015.

  I tried to install the update by using the utility to update the BIOS available in the start menu (after pressing F12). The update failed with the error message "Dell id does not match" or similar.

  Running the update of the session Windows don't seem to have any effect either.

  It seems that the update is only compatible with Inspiron 3443.

  Where can I get the update of the correct BIOS for my laptop? Any help is appreciated.

  The problem has been resolved by a motherboard replacement. Thank you.