Dell U3011 Max resolution problem with Latitude E6510

Similar Questions

• Graphics problems with Latitude E550

  Hello

  I have a problem with a laptop computer latitude and native resolutions.

  I currently have 2 Latitude E5550.

  It has a native resolution of 1920 x 1080 (read in the bios) and the other has a native resolution of 1366 x 768.

  The same drivers (Intel HD graphics 5000 I believe. Video bios 1032v17). Same bios versions. As well on Windows 7 SP1 64 bit.

  My first idea as to why this is because I changed the hard drive in the laptop 2 (1366 x 768 a). It was a drive of 500 GB hard disc, but I replaced with an SSD and installed windows 7 cost. Not sure why this would cause the resolution to be less well?

  Any other information needed let me know.

  Thank you.

  One was ordered with the standard display panel (1366 X 768) and the other has been ordered with an upgrade screen FHD - in other words, the material is different.  This has nothing to do with the drivers, WIndows, etc - a system simply has a screen resolution higher than the other.

• Dell XPS 15 (L502x) problems with mSATA, it is even compatible?

  Hey all,.

  After you run out of warranty and immediately having HDD, I decided to install an mSATA SSD for faster boot times (with the possibility to keep a large spinning for storage disk). I bought a Liteon M3M 128 GB module and installed in the mini-pci-e slot in the compartment under the laptop.

  After that installation there no change, nothing picked up in the bios, nothing through a live Linux OS, nothing in the installer of windows and nothing in Windows itself (when I gave up and replaced the drive rotating and re-installed).

  I've updated to the latest version of the BIOS (A12) but this does not make any difference, I just googled and there is mention of a disabling Intel RST, but this option is not available for me in BIOS

  Is there something that I have done is wrong, it is likely that the device is defective, do I need some kind of pilots of special controller for installation of windows 7 or is this model of Dell just simply not compatible with mSTATA?

  See you soon,.

  -Dan

  Hi Dan,.

  XPS L502X supports the devices in the solid state (SSD) of 256 and 512 GB of capacity. However, I'm sorry to inform him that it does not support the mSATA disks. You can replace the hard drive with an SSD in order to improve the performance of the system.

  Please let me know if you need further information.

• Problem with Latitude E7440, dock E-series & external monitors

  Hello

  I just upgraded to a to an E7440 E6410. I have two Dell 2007FP monitors connected via DVI on a docking station E-series E-Port Plus. These monitors native resolution is 1600 x 1200 @ 60 Hz and my old E6410 was able to run this very well. The new E7440 refuses however to note that 1600 x 1200 is available and that there is an upper limit of 1280 x 1024 @ 60 and 75 Hz. The Intel graphics properties app shows 1600 x 1200 @ 60 Hz is a mode of the monitor support in the Information Center section, but it won't let me select it in the Display Options section.

  Anyone know if it is a fundamental limitation of the docking on the new connector 7000 series or if I just have something wrong set somewhere? All the drivers are up to date for what is the Dell support site is... The computer is running Windows 7 64 bit if that makes a difference.

  Thanks & best regards,

  Martin

  Sorry - should have come back earlier than my IT guy at work found the "fix." There is a updated driver that is for the E7440 but doesn't show up if you are looking for updates of E7440 (?). In any case, I had the drivers are required to:

  http://www.Dell.com/support/drivers/us/en/04/DriverDetails/product/latitude-E5540-laptop?driverId=PTPX3&osCode=W764&FILEID=3292828809&LanguageCode=en&CategoryID=VI

  While the link is E5540 area, the driver is for the GPU Intel HD4400 located in the E7440 as well. This has fixed the problem on all the E7440s that we have here.

  Martin

• Problems with Latitude E7250 & SCCM 2012 R2 (no network in WinPE)

  Hello!

  We have here a weird problem.
  I've added new WinPE 5.x drivers to SCCM, added to the image of boot etc.
  Also added the E7250 drivers and created the driver, added to the task sequence package.
  It worked for all models E4200 until E7240.
  However, E7250 is not functional network in WinPE.

  Someone has good information on this subject, or is broken Dell WinPE 5.x driver's cabin?

  -J

  This page of support solved our problem.

  

  Intel did something weird with the HWID of the NIC on the Exx50 models.

  Jannis-

• Resolution problem with Age of Empires on Windows 7.

  I can't get Age of Empires to work in a resolution of 1280 x 800; It plays only at 640 x 480. I tried all the different compatibility options, and none of them worked. This game worked on Windows Vista, but since I have upgraded to Windows 7. How to get the game to run at least in a higher resolution?

  MS Windows 7 Home Premium
  Intel Pentium Dual CPU T2310 @ 1.4 GHz, 2.0 GB RAM, Mobile Intel 965 Express Chipset Family
  Thank you

  Well, I looked, and I have to do an update of the driver from the manufacturer's Web site. But HP has no updates for my type of computer running windows 7. Does this mean I'm stuck with the resolution 1024 x 768?

  Lonnie7 you have... once more... for a game, you can choose only these resolution which are supported by a game. 1280 x 800 is NOT supported by AoE.

  You remove the black bars, your image is adjusted to fill all the screen and that's all you can do.

  If my graphic card support I say 1900 x 1200 can I run AoE with this resolution? NO! I can only choose these resolution which are supported by a game.

• resolution problem with my monitor every time I turn on

  I have a monitor to display wide w1907 h p on nvidia gforce7050/nvidia nforce 6101.2 weeks I had restore the desktop pc top of page back to default settings since then every time I turn on the screen starts to the resolution of the game and then after a few seconds, it turns into the resolution.i minimum re on this return to the recommended resolution and it stops on this setting until I have put it off and then when I use the PC again I have to repeat the process thanks t..

  Hi Tony,.

  Have you checked that you have the correct nvidia gforce drivers installed from the manufacturers Web site?
  This problem may appear when you have a general driver for the graphics card.

  You could try reinstalling the drivers for the graphics card because it could have been corrupted somehow when return you to the default settings.

  Kind regards

  Joel

• Reference Dell place 11 Pro - problems with the PXE boot

  Before buying a large number of these tablets (11 Pro 7130 venue), I have to ensure that they can be deployed from MS Configmgr (2012). So far, I have no chance for our test model to perform a PXE boot.

  Following the instructions documented by Dell here:

  

  I have a USB dongle to Ethernet Lenovo based on the AX88772B chipset... that is supported according to the documentation. However, try to perform a PXE boot, the screen hangs on the message:

  -----------

  check for the presence of media...

  on ipv4 pxe boot

  -----------

  After awhile, it starts up and then hard disk. BIOS version is A14.

  Any help would be appreciated!

  We have solved this problem by following these:

  

  

  .. DHCP basically has to manage a little different UEFI devices.

• HDMI on Dell ST2310 monitor resolution problem / Inspiron 537/Radeon 4350

  I don't get resolution 1920 x 1080 on my Dell ST2310 monitor using a Radeon 4350 graphics card using the HDMI output.  I get about 1 "black bands black horizontal and vertical.   Strangely, I have perfected 1920 x 1080 when I use the DVI output of the video card to the monitor.  I checked the screen resolution setting in Windows 7 and on the monitor and it is 1920 x 1080 (monitor says just = 1080 p resolution).  Does anyone have advice?

  Success!  Thank you!

  It worked for me, but my settings were VERY difficult to find (someone send this to ATI and Dell, the two companies isn't any idea of this parameter).

  Here are my steps (for Version 2009.0614.2131.36800):

  1. open your Catalyst Control Center in advanced mode.

  2. find the top menu on the left titled: Graphics

  3. select «Desktop & poster»

  4 STEP IMPORTANT: If you have 2 monitors you will see the large monitors in the Middle, and note the SMALL monitors in the lower left corner.  Right click on the LITTLE monitor on the lower left to change.

  5. Select "configure."

  6. click on the tab "scaling Options.

  7 set to 0

  8. click on apply

  9. click on Ok

  You are finished.  I hope someone from ATI reads it and finds that it is much too complex even for an advanced user.  The menu item 'Configure' should have been included at the bottom of the fall of large monitors on the screen.  Why only on the graphics very small monitor in the lower left corner?

• DELL INSPIRON N5110 wifi problem with bluetooth?

  I have a DELL Inspiron, only 10 months and since I reinstalled windows and I'm trying to install the drivers bluetooth and wi fi, during setting up pilots wonder press Fn + F3, he worked as before the reinstallation of the window, but now it does not work, wifi or bluetooth does not get turned What to do now, how to fix it coz I really need the wifi service. In addition, my laptop doesn't have a manual switch or button for wifi and bluetooth. Thank you

  Hello

  Welcome to the community

  In N5110, for wireless card switch is FN + F2. You have reinstalled Quickset application? Otherwise this download link please; http://Dell.to/HInYUY Install and reboot the computer and try to use the card wireless again. You will notice a LED on the left edge of the computer. Let me know the results. Happy to help you!

  Kind regards

• The resolution of the serious problems with after effects CC (2014) on Windows Pro 8.1 on laptop Dell Precision M3800?

  
  

  My new company installed Adobe Creative Cloud (there were a few annoying problems of Proxy at first, due to the seriously tight I.T policy) , but we have a few serious problems resolution with after effects CC 2014 (also have this resolution problem with Adobe Premiere, Media Encoder, Muse) on Windows 8.1 Pro on a laptop Dell Precision M3800 with icons and search interface too small and hard to see is there a fix, an update, or a work-around, can anyone help?

  
  

  Any help will be appreciated!

  
  

  k.regards
  

  Ramon

  I was wrong! :-) Just download the new version. Excellent update. Can finally use it again without changing the resolution.

  I also like the new user interface.  The much better Panel layout. Beautiful interface dark. See you soon. John.

• Satellite C70 - A - 16 L - screen resolution problem

  Hello

  I recently had a screen resolution problem with my laptop (C70 - A - 16 L).
  The max screen resolution which is imparted to me is 1366 x 768, whereas before I think he used 1600 x 900.

  I tried the latest drivers, Bios, etc. and have also restored the operating system to a previous backup, as well as a new installation.
  I also tried to roll back to Windows 7 (with proper drivers). They all offer the same problem.

  This new maximum resolution display correctly - as if the LCD does not deal with the timings of 1366 x 768.
  I believe that the Panel is OK and the problem he reports the EDID information properly - to force windows to use the new resolution.

  Is there a download monitor.inf file that can be used to bypass the EDID reported by the Panel?

  Kind regards

  Antwist.

  If the right to display drver is usually installed everything should be OK.
  Have you installed Intel driver Toshiba download page 9.17.10.3062 version?

• Cannot get the resolution of 2560 x 1600 Dell U3011 connected to M4600 laptop with NVidia

  My setup:- Dell U3011 30'' IPS monitor- Dell M4600 Laptop with NVidia Quadro 1000M - Simple E-Port replicator model PR03X- OS: Ubuntu 12.10, kernel 3.5.0-21, 64-bit (I know it is not supported officially, RHEL is, so I guess there should be a way of getting it work)- Drivers: NVidia proprietary drivers 304.48 (also tried with 304.60)- X.org version: 1.13
  

  According to the specs the monitor should be capable of doing 2560x1600 through DVI-D or DisplayPort.
  

  The problem is: I can't get it to work with DisplayPort even if directly plugged to the laptop. The Nvidia driver seem to detect DP properly, although it doesn't detect the monitor. It only detects the laptop LCD display. If I go to Nvidia Settings, there is no eternal monitor listed.
  
  What I tried and what did not work:
  

  • Turning off the optimus in the Bios
  • connection of the monitor first, then reboot,
  • start first then connect the monitor
  • by pressing Fn + F8 several times
  • go to Nvidia settings and press "Detect displays" - the monitor is off "sleep mode" for a certain time but past sleeping within a few seconds later, nvidia does not detect
  • installation of different versions of nvidia drivers (the most recent, I tried was 304.60
  • completely uninstall the Bumblebee (optimus is disabled in the bios though)
  • using the open-source drivers again (they don't seem to not work at all, even for the computer screen)
  • Delete entirely xorg.conf file

  X.org logs:
  
  [    25.551] (II) NVIDIA(0): Creating default Display subsection in Screen section<------>"Default Screen" for depth/fbbpp 24/32[    25.551] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32[    25.551] (==) NVIDIA(0): RGB weight 888[    25.551] (==) NVIDIA(0): Default visual is TrueColor[    25.551] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)[    25.551] (**) NVIDIA(0): Enabling 2D acceleration[    25.561] (II) NVIDIA(GPU-0): Display (LGD (DFP-0)) does not support NVIDIA 3D Vision[    25.561] (II) NVIDIA(GPU-0):     stereo.[    25.562] (II) NVIDIA(0): NVIDIA GPU Quadro 1000M (GF108GL) at PCI:1:0:0 (GPU-0)[    25.562] (--) NVIDIA(0): Memory: 2097152 kBytes[    25.562] (--) NVIDIA(0): VideoBIOS: 70.08.54.00.01[    25.562] (II) NVIDIA(0): Detected PCI Express Link width: 16X[    25.562] (--) NVIDIA(0): Interlaced video modes are supported on this GPU[    25.605] (--) NVIDIA(0): Valid display device(s) on Quadro 1000M at PCI:1:0:0[    25.605] (--) NVIDIA(0):     CRT-0[    25.605] (--) NVIDIA(0):     LGD (DFP-0) (connected)[    25.605] (--) NVIDIA(0):     DFP-1[    25.605] (--) NVIDIA(0):     DFP-2[    25.605] (--) NVIDIA(0):     DFP-3[    25.606] (--) NVIDIA(0):     DFP-4[    25.606] (--) NVIDIA(0):     DFP-5[    25.606] (--) NVIDIA(0):     DFP-6[    25.606] (--) NVIDIA(0):     DFP-7[    25.606] (--) NVIDIA(0): CRT-0: 400.0 MHz maximum pixel clock[    25.606] (--) NVIDIA(0): LGD (DFP-0): 330.0 MHz maximum pixel clock[    25.606] (--) NVIDIA(0): LGD (DFP-0): Internal Dual Link LVDS[    25.606] (--) NVIDIA(0): DFP-1: 165.0 MHz maximum pixel clock[    25.606] (--) NVIDIA(0): DFP-1: Internal Single Link TMDS[    25.606] (--) NVIDIA(0): DFP-2: 165.0 MHz maximum pixel clock[    25.606] (--) NVIDIA(0): DFP-2: Internal Single Link TMDS[    25.606] (--) NVIDIA(0): DFP-3: 165.0 MHz maximum pixel clock[    25.606] (--) NVIDIA(0): DFP-3: Internal Single Link TMDS[    25.606] (--) NVIDIA(0): DFP-4: 480.0 MHz maximum pixel clock[    25.606] (--) NVIDIA(0): DFP-4: Internal DisplayPort[    25.606] (--) NVIDIA(0): DFP-5: 480.0 MHz maximum pixel clock[    25.606] (--) NVIDIA(0): DFP-5: Internal DisplayPort[    25.606] (--) NVIDIA(0): DFP-6: 480.0 MHz maximum pixel clock[    25.606] (--) NVIDIA(0): DFP-6: Internal DisplayPort[    25.606] (--) NVIDIA(0): DFP-7: 480.0 MHz maximum pixel clock[    25.606] (--) NVIDIA(0): DFP-7: Internal DisplayPort[    25.606] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display[    25.606] (**) NVIDIA(0):     device LGD (DFP-0) (Using EDID frequencies has been[    25.606] (**) NVIDIA(0):     enabled on all display devices.)[    25.607] (==) NVIDIA(0):.[    25.607] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"[    25.607] (==) NVIDIA(0):     will be used as the requested mode.[    25.607] (==) NVIDIA(0):.[    25.607] (II) NVIDIA(0): Validated MetaModes:[    25.607] (II) NVIDIA(0):     "DFP-0:nvidia-auto-select"
  
  What works "partially":
  

  • Connect the monitor using the VGA cable. So I'm able to get resolution of 2048 x 1240, but the picture quality is bad, it's blurred. Not a solution, really. In this context the NVidia driver detects the monitor as U3011 correctly.
  • Connect the monitor using DVI - D (dual link) cable through the dock station. In this context the NVidia driver detects the monitor as U3011 correctly, TwinView works very well.
    However, I get only 1600 x 1200 resolution as the highest option (not even the 1920 x 1200 which is supposed to work with DVI single-link).
    May be that the docking station does not support DVI dual link?
    The connector on the back of it is dual-link for sure, but perhaps there is no connection of double bond between the laptop and the dock?
    Unfortunately, the laptop has a DVI - D, only HDMI, VGA and DP connector, so I can't try a direct connection.
    Or maybe the driver is misdetecting dual-link as a single link connection, and in fact, it might be possible to force it to use the pixel dual-link clock?
  What to try next? Please help, because so far my new U3011 is useless... :(

  OK, so finally I thought, after reading a thread on some Dell 27 "monitor problems DisplayPort (really scary thread, shame on you, Dell).

  The solution was to turn off the monitor, * unplug it from power * and leave it in that State for some time. Now, it works fine, if connected both via the docking station as well as directly. Also, there is no problem with going back to suspend / sleep.

• Firefox has only display problems in the upper left region of only my Dell U3011 monitor; the monitor does not have these problems with any other application

  Some parts of the Firefox window are translucent, allowing the image of the desktop to show through. These regions are anything but great internet site central image which behaves normally. Unless the desktop is completely black this problem makes reading the tabs, address bar and the bookmark are difficult if not impossible. I encounter this problem only on my new Dell U3011 monitor. Firefox is the only application that has this issue on the Dell monitor. The monitor built into the laptop that animates the Dell monitor does not exhibit this problem. The laptop is a Lenovo W540 running Windows 7 64-bit. Thank you very much for your help. Steve Schupbach

  Hello stevesch

  first see : problem with Firefox going transparent troubleshoot and find a solution

  then with patience to see:

  questions/940393

  questions/940389

  questions/940374

  questions/940377

  questions/940384

  questions/940395

  Thank you

• Problem with Dell Latitude 2100 (with windows vista) is a driver (file: \windows\system32\drivers\msahci.sys) catch 22, it's that it doesn't have an internal cd-rom

  I have a dell latitude 2100 and when it is consumed first upward it goes to a screen of security and said that is wrong and it is said that the status of this file is 0xc000000f how I could fix this without an installation disk because it does not a cd-rom

  Hi Rick,

  Thanks for posting your query in Microsoft Community!

  The description of your problem, you are facing problems with your Dell Latitude 2100 and receiving tell them an error message which is bad and he said that the status of this file is 0xc000000f. In order to quickly provide a solution, please answer these questions:

  1. What is the exact error message with error code?

  2 did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: I suggest you check the drive for errors, and then check if it solves the problem.

  Check your hard drive for errors

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

   

  Important: While running chkdsk on the drive, if bad sectors are found on the hard drive when chkdsk attempts to repair this sector, the data available in this area may be lost, and it is not recoverable.

  Method 2: Try the SFC (System File Checker) scan on the computer.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Note: It may prompt you to insert the Windows installation disc. However, you can use the external DVD player and check.

  Hope this information helps. Answer please if you have any additional questions about the problem you are having and we will be happy to help you further.