Design routing question

Similar Questions

• Number of antennas router question?  (Several gadgets WiFi using 1 router)

  -My House is a 3 storey 5 bedrooms single family home.  There are 4 people living under his roof and each person has at least 3-4 items wireless who rely on our network domestic wi - fi.  Include wireless iPhone 2 of 6, 3 iPhone 5, 2 iMac (an older and a new one), 1 airbook, 1 MS Surface, 2 older laptops Apple (the old 1 "thick white), 2 iPads, Kindle 1-2, frame 1 photo wireless, 3 printers, wifi, 1 Sony PlayStation4 (via wifi) and much more.

  Our current router is a double (2.5 and 5) and we use them both, and we had recently a technician change the channels, so we are not in competition with the neighbors.  The router signal strength is strong in the home to most of the places.

  My question: with so many features, would be useful to have several routers with multiple antennas to accommodate this request, or made this same question?

  My current router has 3 visible external antennas.  I read that the Airport Extreme has 6 internal antennas.  I'm ready to go buy Airport Extreme, if 3 additional antennas can help, or if I can use two routers for a total of 9 antennas (if this is important).

  Our services to wide band is xfinity and we have one of their fastest options.  Not quite the 105, but about 80.

  Any suggestions?

  Several wireless routers will tend to work better than the Gothic pulpit super multi-antenna a monster looking for router.

  But they all need to be connected with the ethernet.

  Read how to get excellent wireless in your House.

  http://www.SmallNetBuilder.com/basics/wireless-basics/31576-the-best-way-to-get-ensemble-Maison-sans wire-coverage

  External antennas tend to be more effective than internal, but the actual number of antennas is easily overrated.

  Most of the antennas used on routers now are dual band... which means inside the plastic, they have sections for the two bands... If an antenna is really two.

  Our current router is a double (2.5 and 5) and we use both

  Is what model exactly? Of basic etiquette please.

  We had recently a technician change the channels, so we are not in competition with the neighbors.  The router signal strength is strong in the home to most of the places.

  It would have been correct for the first 5 minutes after the technician left the House and then totally out of place. Channel of all the equipment that surrounds you change every day, every hour... maybe every 5 min. While I don't disagree with fixing channel... others would say that it should be left on auto. You gain nothing much at all.

  If the signal strength is good over a 3-storey house, you are incredibly lucky.

  You can't effectively add routers more unless you install ethernet to provide an infrastructure for data streams.

• Aironet 1140 access point / 1941 router question

  I currently have:

  -router (not wireless) 1941

  -Access point 1140

  Looks like I got the AP on controller instead of the standalone version.  My question is, the 1941 (not 1941W) has a wireless controller?  If not, is there a controller module I can add to my router?  Or I would return the AP I to the standalone version (or the 1941 for the 1941W)?

  Thanks in advance for any advice / help.

  It is not a controller which can go in the 1941. The controllers are quite expensive if you probably don't want to go this way in any case. Before you send the return of accreditation, Sue TAC and see if you can convert it to a standalone. Some AP support this, but I'm not sure of the 1140 series.

  It will be useful.

• Wireless router question: how to acess Channel 13?

  Hello
  Message from a person very technically challenged!
  My router is set to channel 13 and should be able to be used by my pc at home (Qosmio) but he refuses to see the router, now paid twice for a grumpy looking, had changed the wireless card, Tosh make sure it

  Hello

  I found a very interesting forum, posting on the Wlan Channel 13.
  Check this box:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=9296&MessageID=32671

  Please also check this FAQ from Toshiba document:
  http://support.toshiba-tro.de/KB0/FAQ35002P0001R01.htm

• Satellite Pro A60: Wireless router Questions

  Hi all
  I am a novice computer, sorry for my lack of knowledge. I just bought a BT Voyager router for Satellite Pro A60 mt, but can't seem to make it work!

  I was told that my Sat Pro has a built-in wireless inbulit receiver? (If yes how I turn it on?)
  When I conect the router to the phone line saying all the lights on the router everything is ok... but when I try to go to the line, NOTHING!

  Please can someone help me... ???

  Hello

  I checked the properties of the Satellite Pro A60 and it seems that the WiFi card is optional on this unit.
  In this case, you should check in Device Manager if the minPCI wireless network card is properly installed on your machine.
  On the right side of the laptop, you will find a switch ON / OFF wireless. If the wireless network adapter is enabled, the led at the front lights.

  Now something on the router. Each WLan router typically has an own software installation package. There should also be an instruction how to manage the router.
  You should check the router instruction

• Wireless-G Broadband Router questions

  I have a router wireless g broadband. Its model name is WRT54GL and 4 people use 2 using son him & 2 others using Wi - Fi to it. I use a wired connection to the router & for some reason any I'm deformation when I race Nascar Legends online. NASCAR Legends was released in 1999. Is there a way to get rid of this distortion issue I have? Let me know in advance. Thank you.

  Try upgrading the firmware on the router and reconfigure the router from scratch.

• Reset the router - questions

  Hello

  My family and I use the Linksys E1000 router for some time and just yesterday my laptop began to have some problems. I don't know where to start, so I guess I'll just start from the beginning.

  I was at my local college library using the Internet. I closed the lid of my laptop, put on the mode 'sleep', knowing that the class I had then would be not long. However, events conspired to made me forget that I even had my laptop until later in the night, when I was home around 6:30 a. After opening the lid, I found that while my computer has recognized the Cisco wireless network, he was not identified. I stopped, tried again. Disconnected. Stop. Turn it back on. All of these variables on the laptop. Finally I went out to the living room where our router and restart it, unconsciously it rest for too long - and the entire router decided to restart.

  With this, our wireless set came down, and none of the computers were able to connect to the Internet. After a few hours of troubleshooting (my knowledge of comes down to I have a sneaking suspicion about how do to reboot a router so I apologize for the apparent inability), I was able to get through Cisco Connect and launch a new wireless - our network name network thus changing NiceTiger for the original name of the router, then the use of CC - FancyPenguin. I was (and am) able to type the IP address in the bar of my browser, connect, change settings and all that good stuff, but I can't always connect to the Internet. It shows on my network card that I am connected to the router (on my laptop), but it shows that the router cannot connect to the Internet. I tried turning it off modem, turn off the router, thing 2 minutes and nothing worked. The wireless router is connected to the PC out in the living room, and now does not work even on the Internet for this.

  I don't know yet where to start on how to solve it. I tried the fact to unplug cables and waiting. I tried fiddling with the settings, but nothing helped. Honestly, I don't know yet what DNS or none of this means. But I am at a loss to know what to do.

  To resolve this issue is extremely important. I have an online class that I take at the College and without Internet, I can not completed by missions. My grandmother needs pay its bills and my mother runs its business online, so if someone could help, I would be very grateful.

  Thank you very much. If you need details or card or anything, just ask and I'll do my best to help you. As I said earlier, however, I'm a total noob and absolute when it comes to this sort of thing.

  Thank you and have a nice day!

  Ok.

  1. try to disconnect the ethernet cable from the modem to the PC, unplug the power supply and the battery pack inside the modem for about 30 seconds or more.

  2. always disconnect power to the router until you are finished with step 3.

  3. connect the batteries of the modem and power and wait for it to start. Once that is complete, connect the ethernet cable to the Port on the router 'Internet '.

• Several router question

  I have been using my router 4 ports of WRT546s. The ports are used to hard wire the different parts of my house (House was wired). Everything works fine. I need to have more than one internet access wired into my office. So I tried to plug my 4 port BEFSR41 router. I can't make it work. I know that the wiring is done correctly, I suppose that there are changes in my settings, but don't know where to start. I passed my warranty period on my two routers, I'm free looking for advice before I spend $30 to Linksys hotline.

  I use a dynamic IP address automatic and get broadband through Comcast. Thank you.

  Instead of using a second router, the best thing to use in this case is a switch, such as the SD205 SD208 or SD216.  The switch requires no configuration.  Simply connect to your router, and it works.

  To save money, your BEFSR41 can be converted to a switch.  To do this, follow these steps:

  (1) put your entire network.

  (2) unplug the BEFSR41 everything, except a single computer that is connected to a LAN of the BEFSR41 port.

  (3) turn on the BEFSR41 and the computer.  If the computer has a wireless card, turn off the power.

  (4) connect to the BEFSR41 and change the following default settings:

  (a) change "local IP address" 192.168.1.2 (which implies that your WRT54GS uses 192.168.1.1, and you use not 192.168.1.2 elsewhere in your network.)

  (b) change the 'DHCP server' to 'disabled '.

  (c) click the 'Save Settings' button and then wait for the screen refresh (3 to 60 seconds).  You will be probably disconnected from the BEFSR41.  Don't worry about this.

  (5) power down your network

  (6) wire of any LAN port on the WRT54GS at any port LAN on the BEFSR41.  Do not connect anything to the Internet on the BEFSR41 port.

  (7) all the other wired LAN ports on both routers behave as if they were built in the WRT54G.

• Static routing question

  I just took a WRT610N and configure a few static routes for my network.

  I have the router connected to a cable modem WAN and the interface of local network connected to my LAN via 192.168.0.1.

  I have three other LAN subnets in a test environment, they are:-

  172.16.0.0/24

  172.16.100.0/24

  172.16.200.0/24

  I tried to add the following to the first subnet:

  Destination = 172.16.0.0 LAN IP address

  Subnet mask = 255.255.255.0

  Gateway = 172.16.0.1

  Interface = LAN

  No matter what I try, I get a message saying route static invalid, and I can't get anything to stick.  Everyone can't see what I'm doing wrong?

  Thank you guys!

  Gary

  The IP address of the gateway in a static route is the IP address of the connected device directly on each side of the router, either on the ethernet LAN or WAN side.

  In particular you cannot route a subnet of an IP address of the gateway inside the target IP subnet. The static route example you deposited directions where to send traffic destined to 172.16.0.0/255.255.255.0. It is impossible to set the address of the gateway as 172.16.0.1 because the router doesn't know where to send the traffic to 172.16.0.1.

  In other words, the IP address of the gateway must in most cases be a 192.168.0. * IP address that you use these IP addresses in the local network of the WRT. The IP address of the gateway should be the IP address of the router on the subnet specific target within your local network.

  For example, if your second router with address 172.16.0.1/255.255.255.0 IP LAN has an IP 192.168.0.2, then the 192.168.0.2 is the IP address of the gateway for the static route to 172.16.0.0/255.255.255.0.

• Wireless router questions

  Can someone tell me what is a good and cheap wireless router I can buy so I can connect to Xbox 360 live.

  I have an another 360, it would work with a router?

  Yes it will work with both devices, and your choice is correct. If you want a cheaper one that you can purchase a WRT54G.

• CVP newbie on routing questions

  Hello, newbie here in CVP. Got a deployment with UCCE/CVP 9 X and Conn CUCM/Unit 9 X. No Sip Proxy and the current context we have to route calls to CUCM prior routing to ICM/CVP. I know that's not the best Setup, but there is no budget to spend more managers to call for UnityC to CIM at this stage so all calls will be pretty closely from before CUCM hit ICM. That said, I'm getting conflicting information about how to configure routing. Probably more too read things. From my tests, I need 2 PIMS on every PG to cover both CVP servers which means I need 2 labels VRU to account for each customer routing of the CVP (ie. 121212 and 131313)? I have heard however I need one but my call routing will fail if it is not 2. Is this correct? If this is the case, how ICM knows what CVP VRU label to use when a call is initiated of CUCM to ICM? And how is that redundant PVC without proxy SIP or DNS Srv? Any recommendations would be greatly appreciated.

  No, you build the same label for all customers of routing CVP.

  Sent by Cisco Support technique iPhone App

• Cisco SGE2010P routing question

  I currently have a Cisco SGE2010P that I use as my default gateway for everything on my network. I have a static route that points our VoIP traffic on a dedicated line, and that works very well. I recently added a second route that points to another router with a metric of 200. Now, my hope was that if the main road with a metric of 1 was not the next road would be. In my tests, this does not happen. Am I missing something? Now if I put the metric higher as the default route, then phones register and everything works fine. Any thoughts?

  Hi Sean, when packets match several static routes, the gateway sends the packet to the route with the lowest metric.

  -Tom
  Please mark replied messages useful

• The 3845 router question redundant power supply

  Is it possible to swap a bad redundant power on a without voltage 3845 router the router?

  The FAQ at this URL indicates that they ARE actually hot.  Please look at here, under 'System (AC/DC) Power'.

• Web premium CS6 design install questions.

  Just changed the hard drive and tried reinstaling design premium Web CS6 and couldn't perform the task.  Received these errors/warnings: ERROR: DF024, DW063... WARNING: DW065.  You are using windows 7, I do not understand the mistakes or the means to overcome them. Any ideas?

  Run as Administrator http://forums.adobe.com/thread/969395 to assign FULL permissions can help... said yet, but sometimes it is necessary for all Adobe programs (this is same as using an administrator account)

• Design App question

  Hello
  
  first post for me in this forum. Recently, I got a copy of flex mostly to try the new apollo, run time. I catch up with the new AS 3.0 language and mxml (I just flash8). Now I'm porting an applicaton I developed in Flash (a very simple, I'm not a pro) with the help of Apollo and the remote object with the AMFPHP 1.9. Everything works very well expect a fault very little, I can't seem to solve. I created an application of assistant using the viewStack item type. The viewStack contains 4 'pages' and the comboboxes datagrids located inside some of them are supplemented with data from MySQL using AMFPHP. On the "latest" page, I have a datagrid that captures the data based on the selection, the user did on the first page using a combobox control. What happens is that whenever I run the application, the first time that a change event is dispatched to the combobox, I get an error. I think it's because the change event calls a remote method and its outcome, it is supposed to go the datagrid on the "last" page that has not been created yet by flex, so give me an "Error #1009: cannot access a property or method of a null object reference." What I don't understand, is that if I reject the error and use the combobox control again the DataGrid is updated very well. My question is, is it possible to get this datagrid on the last page initialized at the start of the application? I thought that if I initialized before it gets posted, I shouldn't get the erro, right?. I don't know if it's the best way to do it, so if you have any other suggestions it would be awesome. Thank you for your time and sorry for the long post!

  Hello

  You understand the problem well enough and I don't want to immediately give you the simplest solution, but I want to give you the best solution.

  I propose to keep the separate data from the view in a separate category called :) MyData.as where you can place all ArrayCollections, strings, numbers and etc.

  When you interact with the user interface on every page controls, whenever you go to a new page update of data inside myData.as.

  On the last page, link your data grid to the data source in myData.as

  public static class {MyData

  [Bindable]
  public var users: ArrayCollection collection;
  }