Designjet 130nr: lines blue horizontal 130nr

Similar Questions

• DesignJet 130nr: canvas print Designjet 130NR

  Print on canvas of sheet (13 x 19) on Designjet 130NR works very well. Called HP Support asking if there are 24 "canvas rolls that work. Told me and it makes sense, the tool can not handle the Cup fabric.

  Someone at - he found and printed successfully pre-cut large canvases for the 130NR? I've got a good big letter opener, but as anyone who uses the 130 know, it rejects easily paper cut perfectly.

  Thank you

  Marty

  Hello

  Strawberry is not really designed to cut the canvas. Is too thick

  You can still use it, but you will need to replace it more often.

  If your knife used to work, you may need to replace it now

  Here is the part number Q1292-60064 Media knife

• HP designJet 130nr: Spotlight on roller automatic power media must not enter.

  Hello

  I recently bought a HP designjet 130nr used large format, and I noticed that the lights on the Auto Roll power media does not illuminate after I turn on the printer.

  Can someone please?

  The tracer feeds on?  If that's the case then you may have a problem with the drive roller.  If you remove the roll and look down inside you'll see there's a torx screw that mounts to the part of the feed roller who has the power connector.  If you remove the screws (there may be two) and then remove the part you will see there are about 3 or 4 contacts mating when the part is being challenged.  Make sure that none of these contacts are irrelevant.  If the unit power ot on, then remove the parallel cable and the cable to the socket on the printer and plug the unit directly into the outlet. The unit now power on.  Keep in mind with this model when you plug in the cable that the light will Flash several times in front of the screen and the time of glass can turns on but then turns off.  When it fires on the front power button is pressed to turn on the machine.  If the light on the front does not blink a few times you may have a power supply problem.

• Re: HP Designjet 130nr... solved

  Hello

  I have problem my printer HP Designjet 130nr at each startup, it still shows 3 pages by aligning the test print heads.

  Thank you for your help

  Hello

  Thank you
  
  I replaced a cyan Printhead and now everything is back to normal. Now I have a hook to the right and finished leave waste.

  keff

• little blue horizontal lines on the doc, I've done the nozzel check and head cleaning.

  All of a sudden one day when I print there are some blue horizontal lines on the doc, I've done the nozzel check and head cleaning. I have a 810

  Hello

  ·          What version of the operating system is running on your computer?

  Step 1: Check if the problem occurs on a test print.

  http://Windows.Microsoft.com/en-us/Windows7/print-a-test-page

• HP designjet 130nr: CARTRIDGE of black INK HP 130 NR

  Does anyone know how to get cardidges of ink for the HP designjet 130nr printer? It seems that any working on the market! All links will be very wellcome. Thank you.

  PROBLEM SOLVED! I found a supplier for Europe. Thanks a lot everyone.

• drawText along the straight line not horizontal.

  Hello

  Is there a way to draw text along a straight line not horizontal?

  I went through the documentation of the Graphics class and I don't see any variant of the drawText method which can be used to achieve this.

  I'd appreciate comments/ideas to solve this problem.

  Thank you

  -MO

  
  

• Designjet 130NR problems

  Hello

  We have problems with the HP Design Jet 130NR. The week last during a draw of the tracer has stopped working and was infallibly beep, the cause of which I think had fallen to a failure not authentic black print cartridge. We replaced the cartridge with a genuine HP cartridge and acknowledges our yellow/magenta/light magenta show as empty - these appear as "unknown" on the State of maintenance of the system.

  So, I received a copy of the service manual and stripped down to the right side of the printer and there were few black ink that had filtered through the absorbent foam under the ink supply system. I used contact cleaner to clean all the contacts of the cartridge, but in vain. I tried to do the reset/reboot it is indicated in the maintenance manual, but he continually fails to recognize the cartridges.

  All tracer cartridges are at least 50% of the full and geniune all HP.

  Because 3 of the 6 cartridges are no recognized I assume that damage to the ink ink supply system will be the cause? So could I assume that the replacement that should solve the problem? or should there be something else I should be looking?

  Here is a copy of the journal system maintaince (masked ip etc. for intimacy), if this highlights all possible failures:

  For the future refernce anyones solve this problem:

  Replaced ink feeding Station - short circuit - that also killed the chips on 2 cartridges so had to replace those too. System (found on google) maintenance manual explains how to strip tracer apart.

  Then I had to clean the print heads following a guide online.

  Links that I have referred to the (still valid links in June 2014):

  Maintenance manual - http://www.lbrty.com/tech/Manuals_DN/DN_10PS_130PSsm.pdf

  Print head cleaning - http://pindelski.org/Photography/2008/02/27/hp-designjet-printer-head-cleaning-and-repair/

• LaserJet 3600n: lines Laserjet 3600n Black & Blue Horizontal

  Everything prints now has these horizontal lines in them... I know that the drum has a problem that causes the vertical erasure, but it's not too bad...  The lines are, however, a question...

  

  Seems like the wrong toner cartridges.  Follow these steps.  Go into the diagnostic menu and choose the element disable control of the cartridge.  Now when the printer says ready, diagnostic mode, open the toner door and swap the yellow and cyan and exchange the magenta and black.  Don't run the same pq troubleshooting pages that you did before and see if the lines are now is cyan and yellow and magenta or even black.  If still black and cyan, you have two bad toner cartridges.  If magenta and yellow, then you may have a problem with the belt transfer or aft of high voltage.  My gut tells me bad onter cartridges.

• Designjet 130nr will not load any paper format any source

  Hi all

  I was running out of A1 posters and suddenly my printer wouldn't before hand feeding. I tried the paper infeed roller also bit it doesn't work.

  The printer comes essentially upward with the paper with an X if it and the icon of thumb on the display panel.

  It's as if he can't 'see' the paper.

  I cleaned in and around the printer, look for paper jams and ensured that I used the papers good condition.

  One thing I noticed, is that when it takes a roll of paper, it not there no "scan" light more. IIRC, there was before. Also the roll paper feeds out through the printer.

  Etc drivers seem well as he worked all day and no change in software

  Any help appreciated more

  Hello Alan.

  I'll assume a couple of things, please correct me if I'm wrong.

  -What feeding roll paper is detected by the printer and it feeds the paper to print the milling table.

  -transport of good position turns off and moves on paper.  Then paper jam icon appeared.

  This also occurs in feeding tray/feeder manual.

  I saw your other post and yes it can be the black plastic that is bound if the above is correct. There is a lens cap with a small hook under the carriage and the hook connects to the plastic piece to open the lid. With the lid open the sensor line can see the edges of the paper. It might be that your printer has problem with this lens cover opening.

  Solution: If you take the trolley to the left, you can see the hook on the right side, I think. You can leave the lid as it goes and then carefully detach the cover. The printer should work fine without it.

• pdf files are displayed on white background with horizontal and vertical lines blue

  Hello

  When you open in Adobe Pro pdf saved locally, they are displayed on a white sheet with blue squares (see below). This is true for all the PDF files I tried to open it. If the pdf document is opened in a Web browser, and then it appears on the white paper with no squares. Once it is saved locally and open, it appears as shown below. How can I get all the pdf appear on a white background with no blue stripes? It's distraction very during playback! If irrelevant, I installed windows update yesterday.

  

  Press Ctrl + U.

• Designjet 130nr: designjet 130 nr used power up

  It's been a few days I used the machine. When I didn't hit power button / stop no response. I unplugged the power cord for 30 seconds plugged back in. it turned on but no info is showed in the display screen. I was able to start a print job, but the judgment of the printer in the workplace. Yet once I unplugged the machine. waited a minute and printer plugged in back on again and finished the print job. now its completely dead. I tried to unplug and plug in with no change. Help!

  Maybe all of the front panel has gone bad.  Just a guess.  C7796-60208

• HP Pavillion P6532F freezes & lines blue

  Hi, I have a HP Pavillion P6532F. I'm trying to reinstall Windows 7 on this computer, but it hangs and displays what appear to be multiple horizontal blue lines on the monitor. It's extremely frustrating because I won't be able to use this computer because of the issue. Is there a way can I fix?

  Thanks in advance.

  Hello everyone, just thought that I'll let you know.

  Today, I looked in the computer once more to see if there was something I could do. I realized that since it is such an old computer and it has been through so much, the thermal paste on the GPU should be dry. So, I picked up the heatsink on the GPU, and of course, I was right!

  I re applied thermal paste and it worked like a dream! I hope I helped someone else with this problem.

• Hp Envy 14-line blue/static display

  I don't know if this is the right place to post this but I'm going.
  
  http://i.imgur.com/ODxsHNE.jpg
  HP envy 14 beats edition
  Product: XQ104AV
  Model: 14 t - 1200
  (Warranty expired)
  Purchased on April 11, 2011
  
  A week ago, that I was just my computer, then the screen froze. And these multicolored static places and lines that presented themselves. I had to force the laptop to stop because he would not recover.
  Whenever I start it normally it will load and then finally a blue screen. I don't never even put my password.
  Safe mode is the only way to make it, I can manage work (as in the picture).
  
  Basically, what is wrong with it?
  Can it be fixed?
  What is the best course of action to take?
  
  * It may take some time for me to answer. But I will most certainly.

  It's a bad screen or a bad mother. I'd rather the motherboard. The way to test is to connect an external monitor and see if an image appear right on it. If Yes, then the problem is the screen. If the lines and are also on the external monitor then the motherboard video system gone wrong. Please report back if you need assistance.

  Once we have identified the problem, we can discuss the best way to go about it.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Re: Qosmio X 500 - line blue vertical on screen

  If anyone has experienced this? One blue vertical line along the screen.
  I bought in June 2010, the toshiba warranty is over. I buy a warranty extended for 2 years with Lumley... very annoying as now I have to return my laptop and be without for weeks or months.

  What is the history of Toshiba? Is this an error with the X 500-00 X?

  Any comments? Has anyone else had their screen play?

  Thank you

  I put t think that the repair time will be long. The service guys will check what the problem is (GPU I think) and what they need to do is order new mainboard and replace it.

  How long you should wait depends on service guys. Two years ago, I had damage mainboard on my old Satellite A300 and you won't believe me, within 7 days, I got my laptop.

  My advice to you is to contact the service provider as soon as possible. Be nice and explain that you need your laptop soon, then maybe they'll fix it soon enough.