Designjet 130nr: designjet 130 nr used power up

Similar Questions

• HP Designjet 130

  I need driver for printer HP Designjet 130 (Windows 7 x 64)? where can I get it?

  Hi Victorua,

  Here is a LINK you can use to get the drivers and software for your printer.

  Let me know if this solves your problem!

  Thank you

• DesignJet 130: what should look like a NEW Assembly of ink for DesignJet 130 tube to

  I ordered a new Assembly of tube of ink for DesignJet 130 from an online source. The item is marked refurbished. Frankly, it seems not yet to have been refurbushied but just pulled an old printer (but that didn't matter that I was expecting again), but it did lead me to ask a slightly silly question.

  The tubes in a new assembly have preloaded ink in them? I guess not, but when I locate a set of 'new' I don't want to jump to a false conclusion so filled beforehand with ink. I guess they must be clean, dry, seems to have never been filled, and not overflow but I thought I would check.

  I'll get my money back and try again. I guess there are some spare parts new surplus stock for this printer floating around. I was wrong in my assumption?

  Concerning

  New tubes of ink are empty, I installed came with setup printheads.
  
  If my post is solved your problem and click the accepted as button solution under him.
  
  In order to thank a Tech for a post click the thumbs up button under the post.
  
  You can even click on the two keys...

• Designjet 130: Two printers Designjet 130 do not print with Windows 10

  I have two printers Designjet 130. Both work fine with XP/Vista/Windows 7. They do not work with 10.

  I spent 20 hours trying to get these things to work with no luck. I tried TWO different machines running windows 10 does not. These printers are running via a USB connection.

  I can install, make the printer by default and PRINT TEST page! I can also print from the HP Scan DR who assures me that all is well. However, when I go to a program such as Notepad, they will not print. Notepad returns an error "The deal invalid. I tried researching this message, but it leads to good spirits more that I can understand.

  My machine is a processor Intel X 5960, 32 GB of memory and a motherboard Asus x 99 Deluxe.

  I tried to launch the installation of the HP software in a variety of modes compatible with no luck.

  I'm out of ideas other than to roll back my 7 software, which I really don't want to do.

  Thanks in advance.

  Ok. I finally solved this problem. I went to the HP site and even ONCE downloaded the driver Designjet 130.

  Download driver on Dec30, 13:34 had a 2 652 k file size

  Today at 11:53 driver has a file size of 3099 KB.

  Maybe they (HP) fixed.

  Maybe my original upload has been altered.

  Very simply:

  Connect your printer. Windows will find and automatically install the USB printing as well as a device driver option. This driver won't work, however, you end up being able to print a test page. This ultimately will always be a false confirmation. The driver version 7.00 is for Vista, Windows 7 and 8. It doesn't work in either compatibility mode.

  Go ahead:

  Go to devices and printers.

  A series of beautiful graphic icons opens.

  Double-click your printer.

  Double click on "customize your printer.

  Go to the about tab.

  Check your installed printer driver version

  10 Windows will install default v7.00 and will keep you in saying he has the best version

  available. Don't believe that.

  The Hewlett Packard scanner DR software will tell you the same thing.

  Do not think that either.

  You want to version 8.10. It is available on the site of HP in 32-bit and 64-bit versions. Download it. I unzipped in a folder on my desktop.

  Now, go to the Device Manager.

  Scroll down to "printers". Click on.

  Right click on your printer.

  Click on "Update driver software"

  Do not click on the first option by default.

  Do not click on "Browse my computer for driver software".

  Click on "Search for driver at this location software '-specify the folder on your desktop and select"include subfolders. "

  Click Browse. The software will make a satisfying update.

  Return to the file "Devices and printers" and the option "customize your printer.

  Double-click. Return to the 'About' tab and confirm that driver version 8.10 is installed.

  Close to everything and to print something.

  Just to check myself, I printed my second document to confirm a nagging doubt.

  The impression is confirmed. Good year for me and anyone else reading this.

• About light magenta printhead Designjet 130

  I have a problem of clear magenta printhead Designjet 130 (Ref. C9424A).
  I replaced the print head 4 times in 6 months (with sealed new elements).
  Everything worked perfectly before 24cc of ink (12%) consumed on this print head
  After that, the printer starts strips (with magenta).
  I already try to clean or align them, but not best result until I have replaced this with new print head.
  All other print heads are fine. The system maintenance report PDF file is attached.
  any advice will be appreciated.
  Thank you.

  Remember, once a print head has been damaged by the air in the tubes, it can not be fixed. After you make sure that no air flow inside the tube, you must replace it with a new print head. If you indeed extract the air from the tube and then replace the old print head, you will have to remove air from the tube and put a new print head in the printer.

• HP Probook 4520 s used power up?

  My HP probook was working fine until that this morning he died now and just used power upward at all no lights etc. Then I tried another battery, I got and when it is plugged the orange light appears now to say this battery unlike my other one but still no power or anything, keep pressing and holding the power button, but nothing happens? Any help to this or if this is a known defect would be great?

  Joeym90 wrote:

  My HP probook was working fine until that this morning he died now and just used power upward at all no lights etc. Then I tried another battery, I got and when it is plugged the orange light appears now to say this battery unlike my other one but still no power or anything, keep pressing and holding the power button, but nothing happens? Any help to this or if this is a known defect would be great?

  try a hard reset:

  Remove the battery and unplug the DC power adapter.
  Press and hold the power button for more than 15 seconds.
  Plug the DC power adapter (leave the battery for now)
  Press the power button

  Best regards
  ERICO

• How to connect another computer directly using power cord ethrenet

  How to connect another computer using power cord ethrenet, both under windows 7

  Hello

  I suggest you to refer to this link and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows7/help/home-sweet-HomeGroup-networking-the-easy-way

  It will be useful.

• 1V - 5v linear output using power supply 5v, voltage divider, and variable resistance

  How can I get 1v - 5v output linear using power supply 5v, voltage divider, and variable resistance?

  Have the you wired as an attachment?  Using my schema, you can calculate the current flowing through the pot based on the fall of the tension in the pot

  4V / 10Kohm = 0.0004

  Kirchhoff's current law, we know that the same current flows through the circuit so now we can calculate the leg below the wall, based on the current and the fall of desired voltage across the resistance

  1V / 0.0004 A = 2.5 K Ohm

  My scheme maintains the current flowing through the circuit of constant, so the voltage divider must never change.  Assuming a linear pot, you will get a swing of such linear voltage as measured at the wiper.  If you wired the pot, a different way, then more then likely, you change the total resistance of 5V ground that would have the common effect that would effect the tensions.

• Creation of computer virtual using Power CLI

  Hello

  I'm attaching to deploy virtual computer using power CLI but I get the error like below below:

  I use the script below to deploy the VM model exisitin

  New-vm-name testvm005 - VMhost home - model TMPL_W2K3_STD_SP2_R2_x86 - datstorename - OSCustomizationspec-W2K3-ENT-R2-SP2 data store - 32 bit

  New - VM: 25/05/2011 10:37:09 New-VM parameter specified ' Templa
  you ' expect a single value, but your name criteria "TMPL_W2K3_STD_SP2_R2_x86" c
  orresponds to multiple values.

  Can somone help out me on this...

  It seems that if you have more than 1 model with that name in your vCenter.

  Make one

  Get-model

  to check it out.

  If you want to use a specific template, you will need to find a distinctive feature.

  Suppose for example that the model that you want to use is located in a folder named MyTemplates, then you can do

  $template = get-Template-name TMPL_W2K3_STD_SP2_R2_x86-location (Get - file - name MyTemplates)
  

  New-vm-name testvm005 - VMhost home - model $template Datastore - datstorename - OSCustomizationspec W2K3-ENT-R2-SP2 - 32-bit

• HP designJet 130nr: Spotlight on roller automatic power media must not enter.

  Hello

  I recently bought a HP designjet 130nr used large format, and I noticed that the lights on the Auto Roll power media does not illuminate after I turn on the printer.

  Can someone please?

  The tracer feeds on?  If that's the case then you may have a problem with the drive roller.  If you remove the roll and look down inside you'll see there's a torx screw that mounts to the part of the feed roller who has the power connector.  If you remove the screws (there may be two) and then remove the part you will see there are about 3 or 4 contacts mating when the part is being challenged.  Make sure that none of these contacts are irrelevant.  If the unit power ot on, then remove the parallel cable and the cable to the socket on the printer and plug the unit directly into the outlet. The unit now power on.  Keep in mind with this model when you plug in the cable that the light will Flash several times in front of the screen and the time of glass can turns on but then turns off.  When it fires on the front power button is pressed to turn on the machine.  If the light on the front does not blink a few times you may have a power supply problem.

• Request for help with my HP Designjet 130 printer

  Greetings,

  I have owned, loved and used my printer Deskjet HP130 for sixteen years now. I do not use and would like to know if you are able to exchange for another product of your company (HP - printer, laptop or other digital material).

  My contact (deleted content)

  Kind regards

  Paul then

  You must search the HP of the trade program in and then see if there is an another DesignJet you would like to have.

  HP generally offers commercialized ins on upgrades in the same line of equipment.

• Designjet 130, OS x 10.7.2 Designjet Maintenance Utility software

  Hi I have a difficulty to find work Designjet Maintenance Utility software for my iMac OS x 10.7.2.

  Any ideas wher download a?

  Thank you!!

  At this point, it is all the software that I see for 10.7 and your printer: http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=352389&prodTypeId=18972&prodSeriesId=352387&swLang=8&taskId=135&swEnvOID=4114

• Designjet 130: Bland green to blue

  I am trying to print a banner 24 "x 72" (plain paper) with a green background. What impression it fades to blue. The point where starts fading is different.

  Initially I thought that the yellow cartridge and print head may need to be replaced as blue + yellow = green. But I am able to print Yellow without problem.

  I replaced the cartridges/printheads, aligning the print heads, calibrated color, physically cleaned areas of ink myself (slightly) and a lot, a lot restarted and printing tests.

  If anyone can provide advice, suggestions or directions, I would be very appreciatve and grateful!

  Thank you very much

  Return to the print head and you'll see the stem that fits into the rubber on the front of the truck part.  You need something small with a PIN at the end to fit into the rubber part.  You then draw the ink with the syringe.  Remember if you can't draw handwriting, where the needle will not move again to draw it, then the tube is clogged and you can be out of luck.  Some people in this case use the same syringe to force a small amount of windex in the tube and let stand for a few hours to see if it opens the tube.  Good luck.

• Satellite NB10T-A-102 used power up - no lights

  Hello

  My NB10T-A-102 SATELLITE has stopped working together 9 days after that its warranty (1 year) lack. Its been a great machine (so far), his dishes seen very little, it is not carried on many (just for most at home). I tried power until Sunday morning and nothings happening, no lights at the front then he seemed to want to do something (like he was pressing the last battery juice) but then nothing. I checked the power supply with a multimeter and its delivery 19v which is correct, but there is no (orange I think) led on the front of the machine. IV tried to take the battery and discharge the static electricity, but nothing seems to work.

  Any ideas? Quite disappointing if its totally given upward after a year of use of the lamp.

  If the power supply light is not illuminated when the AC is plugged, its most likely a motherboard problem.
  ASP can repair
  www.toshiba.eu/innovation/generic/ASP_SUPPORT/

• Battery Tecra M11-130 with not power and the fan runs constantly

  We are having a problem with the battery on one of our laptops. When left for an hour or two the laptop turns off because the battery is dead. We have mounted a battery new but still only get about 1.5 hours.
  In addition, the fan runs continuously. I looked at the PC Healthcheck software which shows as follows:
  * Power *.
  Other costs 14%
  40% of energy consumption system
  Good battery
  * Temperature and fan *.
  CPU temperature 67%
  System internal temperature 56%
  88% fan speed

  I would like suggestions.

  > We have mounted a battery new but still only get about 1.5 hours.

  1.5 hours is a common value, you should consider that dough working time depends on its portable use.

  Battery needed to dump a lot faster if the CPU would be stressed out a lot in your case, that something could run in the background, lose power CPU performance and the dough.

  In addition, you said that the fan runs constantly this could discharge the battery too.
  Therefore, it would be interesting to know what process emphasizes the central unit.

  Start the Task Manager and check the processes tab. In the CPU column, you can find the process that emphasizes the central unit.

  In addition, to change the settings for the CPU performance and cooling of the activities in the options of Win 7 powers that would help to increase the performance of the battery.