DesignJet 9050 does not receive task until you press the Cancel button

Similar Questions

• Two Macbook Pro, both does not start up, when I press the power button, I hear two disc bit Caryl, I see little light on the front on the displasy release button, black screen, no edge

  It was weird because I've NEVER had two computers have the same problem before. They are the model 2008 2.2 Ghz Core 2 Duo, 6 g of RAM, models of 128 GB of hard drive, the two Yosemite running, both had new hard drives, cables, batteries and RAM installed OWC (Apple approved reseller) and I use Macs for at least 20 years. In about a week, one just blacked out while sitting on my desk doing nothing, the other does the same on a week later. When I press the power button, I hear the drive hard hum twice, then all I get is the little light on the screen release button, that's all. Black screen. fails, nothing. I can press the power button and it will fit off the coast. Is it possible that some of them have infected somehow, or possibly send me the malware that has infected my system? I would not normally only, but for all of them to go down to one right after the other with the same problem just made me think, it must be the same cause, but what?  I had been in a war of fire recently with very ugly people, and I've never seen two Macs have the same exact problem in a row like that right.

  I took readers on the Macbook Pro, put them on sleds and threw them in my PowerMac, and both seemed fine, no problem, started well upward, ran utility disk on them, no problem, so I started to the checklist. Reset the PRAM. Nothing. SHIFT key at startup. Nothing. D at the start. Nothing. V order at startup. nothing. I wouldn't mind even their evisceration and making a portable useful with the parts of the two, but until I find out what the problem is, what can I do?

  If anyone has any suggestions, I would really appreciate it, I've supported every button I can think at the start, tried an inch USB key, boot and disk, this is the same Caryl bit both of the car, no chime, black screen, that's all.

  Thanks for your help.

  Damicon999 wrote:

  Is \Is possible for someone they have infected somehow, or possibly send me the malware that has infected my system?

  no chime, black screen, that's all.

  I don't think they are infected.

  The startup chime indicates that the Mac has made the initial diagnostic tests and there is no hardware problems or fundamental software.

  No edge in your case is a problem.  I think it's the luck of the draw to have 2 failures.

  In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

  Genius of booking http://www.apple.com/retail/geniusbar/

  Online https://getsupport.apple.com/GetproductgroupList.action

  check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

• ElliteBook 8460p will not be running when you press the Start button

  Hi Ant classmates.
  
  I am facing a problem with my 8460p ElliteBook. When I press the Start button it won't start and I need to apply some mechanical vibrarions so he reacts to the button. I guess that there is a problem with a connection inside. The thing is that he does not always fail, but it happens more often. I'm afraid to send it to HP support and resume with a message like "the problem didn't see the - up." I'm close to the date limit of warranty, but I need my laptop for 3 more weeks for professional issues. What should I do?
  
  Thank you

  Hello Angelica,.
  Welcome to the HP Forums.
  
  I'm sorry, but to get your question more exposure, I suggest posting in the trade forums, since it is a commercial product. You can click here for the link.
  http://h30499.www3.HP.com/hpeb/
  
  Thanks for posting on the HP Forums.

• Why Satellite Pro A300 does not start when you press the power button?

  Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

  In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
  Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

  What should I do to get a normal departure procedure?

  When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

  When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
  The same thing happen on my Satellite A300.

• A font I need is not available in italics. Corel Paint Shop Pro produces the police in italics when you press the Italic button in the software, but I don't see any way to do this in Illustrator. Help, please.

  A font I need is not available in italics. Corel Paint Shop Pro produces the police in italics when you press the Italic button in the software, but I don't see any way to do this in Illustrator. Help, please.

  Select the text and use the Warp tool to give a fake italic.

• PowerEdge T410 won't do anything when you press the power button / stop.

  My work has recently retired this t410 server. It worked without any problems when he was arrested. I had to remove and destroy the hard drives from the system. After that, I was allowed to bring home for my own use. I installed a new sata drive and plugged into the power supply and a free sata port on the motherboard. I get nothing when I tried to boot the system. This version has the unique power. Power light only lights up when you press the test button. System fan is going at full speed, but stops when you release the power button. Also on the control panel lights 1,2 and 4 and HDD power on and turn until the test button is released. There is a single green light lit on the motherboard, while it is plugged. Apart from that, I have no response when you press the main power button. Can anyone tell how to try to get it up and running again.

  -Who-

  I have not received the answers more so I think that this issue is ignored. So I'll let everyone know what finally happened. I solved my problem after a lot of electrical testing. I found a diagram of the arrangement of the power dell power supply pins and I made myself the best possible meter test. After several rounds of tests, I found several pins that did not have the right voltage. I bought a new power supply. I installed and replace everything. I plugged into the system and it auto fed on itself. I loaded from an OS and it works perfectly.

  Problem solved

• Hi, actually I want the program stops when you press the stop button. but the problem is the program is runing in loop only he doesn't return tile view deleted complete execution of any body can help me for this.

  Hi, actually I want the program stops when you press the stop button. but the problem is the program is runing in loop only he doesn't return tile view deleted complete execution of any body can help me for this.

  Here

• iPhone does not appear when connect you to the computer

  I use iPhone with iOS 9.3 6, recently I upgraded my iTunes to version 12.3.3.17 (64-bit) and my computer is running on Windows 10 Pro (64-bit).  After the upgrade, when I run the iTunes, my iPhone does not appear.

  I tried the following: re - install iTunes, stop and restart the Apple Mobile Device Service, remove the Lockdown folder, but still, my iPhone is not recognized by iTunes.

  Any suggestions to solve my problem?

  You have a third party Virus Scan running on the computer?  Sometimes it can get in the way of communication between iTunes and the phone, especially after an update to iTunes.  Try disabling the antivirus scan and see if the phone appears in iTunes.

  Other devices work on the same USB port?

• PC does not start when you press the power button, after that starts automatically as a ghost!

  I have HP Pavilion a6030in, my pc does not start when I press the power button / stop ther, but she starts automatically after some time after that, it works fine.

  Even once when I closed and leave it for a while and still the problem is not resolved.

  Help, please

  I solved the problem

• Page does not update even though I pressed the shift I click Refresh or press F5

  In another web browser the SHIFT + F5 reload all the content of a page update. This does not work in Firefox.
  I like Firefox the best browser for me. But I can't continue to use with this problem.
  I'm a software developer. I need a control tools and it was driving me crazy.
  All my friends told me about the same problem in Firefox and have migrated to other browsers where this issue does not work.
  If you want to keep Firefox up, always operate at least with the characteristics of base like that!
  Sorry my English.

  Hello

  Please also try Ctrl + F5 to reload the new page.

• My photo jitters folder and does not respond when I click on the maximize button...

  Hi, I have a problem with the MY PICTURES folder in windows 7, it opens and I can get to all my files but when I want to use the maximize on the upper right button it reduced to a very narrow waist and jitters like crazy, then MY PICTURES folder does not. I have to close the program to get back in it. Any help would be apreciated. Thank you.

  Visit the Web site of factory for the video card driver updates,

  Usually in the support section.

  F11 key is a better alternative, any mouse not necessary.

• Phone does not save when I click on the SmartBand Button

  Hello.

  I have a Smartband SWR10 and the other day I discovered that nothing happens when I click on the Smartband button. It should start the media player. When I double tap on the button, it must create a bookmark of life on my phone, but the Smartband just flashes and nothing happens on the phone. It has worked before. The phone and the smartband are connected, because when I get a call or an alarm my Smartband vibrates.

  So, what can be the problem?

  Been a while that I used it, but I think that you must also type the tape (hit it softly) when you press the button.

• IPhoto crashes when you press the info button

  Since very recently, IPhoto crashes every time when I press the info button to enter people information a photo. I have version 9.4.3. running on OSX version 10.8.5. I added the first lines of pages and the pages or error report, if that can help anyone. I tried to repair the basis data, but without success. I am very grateful for any advice on this issue.

  Process: iPhoto [552]

  Path: /Applications/iPhoto.app/Contents/MacOS/iPhoto

  ID: com.apple.iPhoto

  Version: 9.4.3 (9.4.3)

  Generation information: iPhotoProject-720091000000000 ~ 1

  App item ID: 408981381

  The external application ID: 15017489

  Code type: X 86 (native)

  Parent process: launchd [139]

  User ID: 501

  Date/time: 19:50:47.475 2016-01-04 + 0100

  OS version: Mac OS X 10.8.5 (12F2560)

  Report Version: 10

  Interval since last report: 34492 sec

  Crashes since last report: 3

  Per-App interval since last report: 905 sec

  Per-App crashes since last report: 3

  Anonymous UUID: 23235B01-625D-2A47-6A8F-352C3092B10A

  Crashed thread: 0 dispatch queue: com.apple.main - wire

  Exception type: EXC_BAD_ACCESS (SIGSEGV)

  Exception codes: KERN_INVALID_ADDRESS at 0x00000000c53b6a10

  If you use iPhoto 9.4.5 or an earlier version, iPhoto will crash whenever you try to use maps. It is no longer supported.

  See:

  The first versions of iPhoto 11 started to plant for many users suddenly last month.

  There is a problem with the functionality of the site, because Google maps will no longer be supported.

  See the solution of Huxly647:

  Huxly647 , November 20, 2015 12:05 AM
  Re: iPhoto crashes after opening several times in reply to carvermon Useful

  I found a solution that works for me...

  1 goto /Applications/iPhoto.app/Contents/Resources

  2 delete the files 'googlemap.html' and googlesearch.html

  IPhoto no longer crashes, site does not work, but it doesn't bother me too much.

  Let me know if it works for you guys...

  Deletes two files "googlemap.html" and the googlesearch.html of iPhoto application bundle prevents the JavaScript running inside and causing the accident.  Log of course do the same thing. So it's pretty clear that something happened at the end of Google.

  To access the files inside the iPhoto application select it in the Finder and ctrl-click on it. Then use the command "Show Package Contents" from the menu.  Open the content subfolder and then resources.

  Do not try this fix without making a copy of the iPhoto application before trying to delete the two files of the entire application.

• Videos a pause when you press the volume buttons

  Hi, I have a problem while watching videos on YouTube or not... When I use the high and low volume keys, the video stops without reason and I find it so boring... I think it started about a month ago... Can solve us this problem? Thank you

  @Ehabg

  As I thought, the problem its caused by a third-party application, not a preloaded app, you need to uninstall app by app until you find the culprit.

• Audio jack play and pause/stop when you press the various buttons

  Hi all

  I do a simple radio interface and I have 6 buttons which I want to have that specific preset song playing of the button located in the library screening and stop/pause the current song when you press any preset button.

  I tried to use the attachSound, with associated identifiers but don't know if it's the right way to go. He plays songs, but does not stop their...

  {mc_FM1preset1.onRelease = Function ()}
  {if(!this.) Toggle)}
  this.gotoAndStop ("release");
  radio_FM1. Text = FM1preset1
  FM1value = 1
  
  PlayFM1_1 = new Sound (this);
  PlayFM1_1.attachSound (FM1preset1_song);
  PlayFM1_1.start (0, 1);
  
  PlayFM1_6.pause;
  PlayFM1_5.pause;
  PlayFM1_4.pause;
  PlayFM1_3.pause;
  PlayFM1_2.pause;
  
  }
  }

  
  }
  {mc_FM1preset2.onRelease = Function ()}
  {if(!this.) Toggle)}
  this.gotoAndStop ("release");
  radio_FM1. Text = FM1preset2
  FM1value = 2
  
  PlayFM1_2 = new Sound (this);
  PlayFM1_2.attachSound (FM1preset2_song);
  PlayFM1_2.start (0, 1);
  
  PlayFM1_6.pause;
  PlayFM1_5.pause;
  PlayFM1_4.pause;
  PlayFM1_3.pause;
  PlayFM1_1.unload;
  
  }
  }

  then I tried just to put each piece in its own clip and using this code, but it still doesn't stop/pause the song.

  Stop();

  {mc_preset1.onRelease = Function ()}
  mc_song1. Play();
  mc_song2. Stop();
  }

  
  {mc_preset2.onRelease = Function ()}
  mc_song2. Play();
  mc_song1. Stop (1);
  }

  Does anyone have any suggestions? Any help would be great! Thank you!!!

  Basically, I just need to know how to do the supported mc or button to STOP / to PAUSE the song that plays

  Thank you!!!

  -PAt

  the sound class has no property of break.  It has a stop() method, you must use:

  {mc_FM1preset1.onRelease = Function ()}
  {if(!this.) Toggle)}
  this.gotoAndStop ("release");
  radio_FM1. Text = FM1preset1
  FM1value = 1
         
  PlayFM1_1 = new Sound (this);

  
  PlayFM1_1.attachSound (FM1preset1_song);
  PlayFM1_1.start (0, 1);
         
  PlayFM1_6.stop ();
  PlayFM1_5.stop ();  etc.
  PlayFM1_4.pause;
  PlayFM1_3.pause;
  PlayFM1_2.pause;
         
  }
  }

  }
  {mc_FM1preset2.onRelease = Function ()}
  {if(!this.) Toggle)}
  this.gotoAndStop ("release");
  radio_FM1. Text = FM1preset2
  FM1value = 2
         
  PlayFM1_2 = new Sound (this);
  PlayFM1_2.attachSound (FM1preset2_song);
  PlayFM1_2.start (0, 1);
         
  PlayFM1_6.pause;
  PlayFM1_5.pause;
  PlayFM1_4.pause;
  PlayFM1_3.pause;
  PlayFM1_1.unload;
         
  }
  }