Detection of MDS via WiFi access

Similar Questions

• My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  Sync your iPhone, iPad or iPod touch with iTunes using a WiFi - Apple...

• Access Internet via WiFi with E3200

  Hello

  is it possible the E3200 router to connect to internet via wifi (WLAN) interface?

  In fact I can use the ethernet port called 'Internet' to connect with my router Fritz Box (which is responsible for my internet connection to my DSL provider).

  But I don't want to use 10 m or over ethernet cable in my apartment, so it would be good to use just wifi.

  Can someone help me get this to work?

  Thank you very much.

  Lol it is not possible. It's a completely different operation mode. The E3200 has an access points wireless that accepts incoming connections from clients. You want the E3200 to connect to a different wireless access point, either you want the E3200 to customer connect to an another acccess points.

  Which is like a cell tower: it accepts connections, but it connects to the other rounds (at least not using cellular frequencies).

  This has nothing to do with the routing to this level, but only with basic connectivity.

  The E3200 with Linksys firmware requires a wired connection.

  3rd party firmware may allow you to use the E3200 as bridge or wireless Repeater same as wireless, perhaps with the FritzBox. But we have to ask in a dd - wrt forum for this.

• Internal access to the site at the remote location via wifi

  We have an internal site to A location and we have a 2 layer hose B location. When you use the ethernet connection, site B can access the site. What we want to do, is allow them to access via wifi with the VPN site to site (who currently works) hosted by of our Sonicwall.

  How this is a problem is our network is separate; wifi at site B is on the DMZ. We added access rules to allow the DMZ-> VPN traffic on the site, which did not work; No ping, no traffic, no communication. We've also added policy NAT, same story.

  My theory on why it does not work is because the VPN tunnel to one SW to another is related to X 0, but even after enabling access, it's the same result.

  Any help would be appreciated. Thank you all!

  Hello

  Is DMZ subnet to site B added under 'Local networks' VPN B Site and under 'Remote Networks' policy in Site A VPN policy? If you have then SonicWALL auto-créera access rules to allow WiFi traffic. Basically, you need to add the DMZ subnet in site B the VPN policy.

  You can also see the article: https://support.software.dell.com/kb/sw7725

  #IWork4Dell

• Only browsers and AVAST cannot connect to internet via ethernet. Computers on the same router via WiFi, MS update, ping cmd - all access

  Help! I'm about to commit the homicide of the computer!

  I have been troubleshooting for weeks and am now bald from ripping my hair!

  Computer: Dell Inspiron 537 s Slim Desktop  w / Pentium Dual - Core CPU E5200 @250 GHz

  Network card: Realtek PCIe FE Family Controller (checked several times, through Windows, it works correctly)

  System: Windows 7 Home Premium, 64-bit with Service Pack 1

  Router: Netgear N600 model #: WNDR3400v2

  Cable router: SBV5220 Surfboard Motorola

  Now several months ago this desktop computer once more had SOME programs lose the ability to access the internet via an Ethernet cable.

  Affected programs:

  MS Internet Explorer

  Mozilla Firefox

  Avast! Security Suite

  Work of MS Security Update

  Ping works sites (Yahoo, etc.)

  Other computers connected to this network via WiFi - no problem getting on the internet.

  Run the network troubleshooter advises all is working properly, no suggestion.

  Attempted fixes:

  Turn off all extensions on IE (but don't forget Firefox and Avast! are also unable to access.)

  Disabled all start-ups and the package process

  Restarted in Safe Mode - still not able to access.

  Ran check complete virus, then check virus run start. Minor ad-ware 'virus' not found, all corrected automatically.

  Rebooted the router and the computer to infinity and beyond! s

  Tried other computers using the same ethernet cable connected to this wireless routers cable, no problem accessing the internet.

  Disabled functions package

  Off MS Firewall

  IP Reset configuration (memory: netsh ip net reset c:\resetlog.txt - without DOUBT NOT EXACT - OF THE MEMORY.) Command worked)

  As I said, this had happened before and then miraculously fixed itself after a short period (less than 1 week). This time, no joy.

  Of course, it's one of two things:

  (1) a configuration problem I just can't find/understand.

  (2) the problem of equipment more strange, more selective, in the universe.

  Anyone? Anyone? Bueller?

  Thank you more can I possibly Express for assistance.

  You could win the lottery and have a lot of beautiful children!

  (M.) Kel

  Hello team zig - zag,

  I wanted to thank you for your help. I finally broke down and reached out to our friends at Microsoft directly for assistance. They had me a role through all the things that you suggested (again). And finally (after many hours of phone and chat discussions) came up with an answer: "* shrug * we don't know what is the problem - choose a restore point and come back to that.» What I did. This has solved the problem of internet access, but created other problems I'm trying (nothing that I have to post here, they are specific to a particular program package).

  Still, I wanted to thank you for your time and effort on my behalf. I'm very, very happy!

  All my best,

  Kel

• the running program on myRIO with access to controls via wifi

  I built balancing robot using myRIO. It does not perform very well and I can control it via wifi. I have now the Setup is simple enough: I can control and set PID and Kalman (accelerometer gyroscope) values. However, there are significant delays associated with the wifi connection. Therefore, if I am happy with my performance robot WiFi (all the controls value) and then I deploy my program on myRIO - changes in performance of robots since the program is run on myRIO now and there is no bottleneck related to sending the data back and forth between computer and myRIO.

  To avoid this: is it possible to run the program under myRIO but have a link with all the necessary controls on wifi?

  Kind regards

  Drakon

  Drakon,

  Looks like you want to use your computer as a GUI that will read and write variables shared network your myRIO can also connect to.

  http://www.NI.com/white-paper/5484/en/

  It is quite common to all the treatment more push to a real-time controller while having a user interface on a computer that will basically just reading and writing shared variables.  I don't know if this is what you were asking, could you explain what you are currently on your myRIO and your computer, problems you have with your current setup and you want to change?

• WET11 V2 cannot be connected to the AP (access point) via WiFi

  I am facing following problem.

  Someone at - he advice me please how to solve these problems.

  Purpose:

  1. I want to use internet on TV Sony Bravia. (Bravia has no WiFI. "I have only LAN).

  Environment:

  1 access point (Router) - WiFi > WET11 V2 - LAN > TV (Sony Bravia).

  2. IP address 192.168.1.5 = WET11 (automatically not static)

  BOF WET11 V2 assigned IP address access point.
  I checked the access point access point IP attributed to WET11.

  3 TV IP address is automatically.

  But the IP address is unaffected for television.

  4 WET11 firmware version = V2.05 (Sep 16, 2003)

  Problem:

  1. IP address cannot be assigned for television.

  2 WET11 is not the answer for the command 'ping 192.168.1.5' WiFi access point.

  3. I did ping command when the LAN TV cable has been replaced by the wireless access point LAN cable.

  BR

  Mutt

  It is not advisable to use a 802. 11B wireless bridge on a device such as your streaming media TV. Connection will be very slow and is probably the reason why you have a hard time to connect to your wireless router that's more compatible with it. I suggest using a Wireless N bridge or a multimedia wireless on your TV adapter so that you can fully appreciate the media streaming.

• Access to corporate blackBerry Smartphones via wifi if e-mail isn't on a support

  I have a torch 9810 via AT & T. If I turn the cell off the signal and just use wifi, I get all my emails professional very well. Don't need a cellular signal.

  What happens if I cancel AT & T altogether and do not replace it with any carrier. Then I connect my blackberry via wifi to internet. Will I always have the corporate e-mail?

  Part of me said 'Yes', because there is no reason not to. I can turn on the Bberry, connect it via wifi and get email. AT & T is superfluous.

  Part of me said: 'No,' because I don't know, maybe that when I cancel AT & T, Blackberry (the company) "disqualify" me their server (or something) and therefore the phone is a brick.

  Hello and welcome to the community!

  BBs legacy (pre-BB10), all BB exclusive services, including e-mail, depended on an active account to BlackBerry Internet Service (BIS). The device itself does not have an email client full... depends on BIS in order to provide messaging functionality. And BIS infrastructure is hosted at carriers and BlackBerry - and is used for your email at any time, regardless of the channel (carrier or WiFi data network) that you have active on your BB.

  So the long and short of it is that if you cancel your BIS account (due to the cancellation of AT & T), your email will stop working (because your BB will no longer be able to communicate with BIS), even if you only use WiFi.

  The BB10 BIS is removed, replaced by a full e-mail on the device... so client, BB10 device can work perfectly for send only via WiFi, because there is no need to talk to BIS. But legacy devices must speak BIS.

  Good luck!

  Edit... I just noticed the use of the word "business". If by that, you mean BES, then the same situation applies always... it is just a story of BES-level (from your carrier) instead of a BIS account which is required for features.

  See you soon!

• No Internet with MacBook Pro Via WiFi or Ethernet

  My MBP has ceased to connect to internet via WiFi approx. 2 weeks ago. No settings have been changed to our MBP or router. Ethernet connected directly to the router/modem does not work as well. "Wi - Fi was free assigned ip address", on network settings. Also, I can not connect to Wi - Fi to parents/friends/starbucks as well. I searched the forums but have not found a solution. Thanks for your time.

  Please start in recovery mode. In the OS X Utilities screen, select get online help. It will launch a clean copy of Safari. Some plugins, such as Flash, will be available. While in recovery, you do not have access to your saved bookmarks or passwords, so take note of those who before, if they are required for the test.

  Test. After testing, restart as usual and display the results.

• 5s iPhone stuck on apple Sun logo after that iOS updated 9.2 to level via WiFi

  On December 9, 2015, my 5s 64 GB iphone posted a notice that the iOS 9.2 update was available. I went to update via WiFi, but after the upgrade, the iphone starts in a screen of the apple Sun logo. What state is the apple Sun logo indicates in fact? I tried to do a hard reset several times without success. It's quite frustrating to be invited to upgrade your phone with an update of the software and receive instead a disabled device. How to restore normal functionality?

  You can restore the device in iTunes putting it in recovery mode. To do this, follow these steps:

  1. Connect the iPhone to iTunes
  2. While it is plugged into your computer, perform a hard reset by pressing and hold the Power + Home keys until the screen goes black
  3. KEEP pressed the home button but release the power button.
  4. Keep holding down the home button until you see the iTunes recovery screen (should look like the screenshot below)
  5. iTunes should have detected the iPhone in recovery mode and allow you to click on restore to restore the device.

  Note that you will lose all personal information by doing this. I hope that you all had your backup of important information previously. I hope this helps!

  

• HP Officejet pro 8100 cannot wifi access point?

  Yesterday, my HP Officejet pro 8100 arrived and I try to connect via wifi. I thought that it need access to infrastructure to print via wifi.

  When I turned on the printer I osserved that he create a stand-alone gateway with SSID: HP-Setup-7 a-Officejet Pro with IPv4 server address, etc...

  I was very happy and I printed a page with my smartphone samsung s4 directly connected printer access point (no wifi direct wifi except standard).

  Has been held today has changed, but I can't use printer with its own point of access, but only with an external wifi access point.

  Can someone help me, please? It could be a hardware problem?

  Thank you

  Luca

  P.S. to the webserver I checked 'connectivity point of access' (di accesso instradamento wireless in Italian Punto) is checked.

  Hello lucait

  You are right that the Hp Officejet PRo 8100 is a single function printer which does not directly optional wireless. You can always do what you want to do, but you will need a router to connect the printer to a network, and from there you can use the network routers or set up the feature ePrint for your portable devices.

  I hope this solves your post. Thanks again for the display on the HP Forums. It has been a pleasure. Have a great day!

• I can't connect to internet via wifi

  I use a laptop and a second laptop can connect but my office will not connect to any kind of work more after about one year.

  Hello pjw7167,

  Welcome to the Microsoft community where you can find all the answers related to windows.

  According to the description, it seems that you have problems with the wireless connection. As I understand it, that you can not access Internet via Wifi.

  I need to ask you some questions to help you better.

  1. do you get an error message when you try to connect?

  2. the problem when you try to connect by cable?

  3. were there any changes (hardware or software) to the computer before the show?

  Perform the steps in the link and check.

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  Answer to us if you are experiencing problems with wireless networks or any other problem of Windows, and I'd be happy to help you.

  Good day!

  Hope this information helps.

• EAS does not connect via wifi company post - 1.3.5

  This seems to be a somewhat different issue of EE that some know, so it was recommended that I start a new thread. My question: I can access is no longer to EAS via the wifi of my company. It worked before 1.3.5. If I turn the wifi off, I can then connect EE without problem. I get no error when connected via wifi, rather e-mail and calendar just don't update.

  It turns out that our firewall is configured to disallow connections since our internal wireless to internal resources through external access (that is, accessible through the Internet). This explains why it is not working currently - other devices exhibit the same behavior, including iPhones and laptops.

  The question then becomes: why it worked before? I can check before 1.3.5 I can be connected via wifi to my company and still connect to the Regional service. So the previous version tried to connect via wifi, then when he could not, did he switch to EVDO to connect?

  If this is the case, then it is a very nice feature and it would be great if it was turned off. If it is not the case, then I have no idea why it worked prior to 1.3.5.

• OfficeJet 8600 more: HP OfficeJet 8600 Plus installation on a different subnet via WiFi

  Hello world

  We just installed a new Watchguard router with wifi built-in. The computers on the network are all on the 192.168.0.X subnet. Wifi is configured as an access point to assign different 192.168.1.X subnet. The wired and wifi are "trusted".

  The 8600 is connected successfully via WiFi and I can ping the printer from a computer located in the other subnet. However, when I run the installation of the drivers on the workstation, it can not find the 8600 in the other subnet? Even if I try to manually enter the IP address of the 8600, it won't find it.

  Is this a limitation of the software install HP where it will not be on other subnets to find the printer?

  Thank you all and I thank you for the help

  Mike

  Not going not to happen. You must be on the same subnet so that the computer and the printer works. Basically, the first 3 octets must be the same. 192.168.0.x or 192.168.1.x cannot have both.

• E4200 and WDTV live via wifi without DNS error?

  Someone does it, I mean EVERYONE, got a WDTV live hub to successfully connect to the E4200 via wifi without getting a DNS error?

  My system:

  E4200, fw c. 2.1.39.145204

  WDTV Live Hum, fw c. 3.08.14

  DWA-160 (Rev.) (A) usb wifi dongle fw v. 1.80

  My sony wifi equipped blueray connected to the E4200 without boredom and access the USB HDD connected to the E4200.

  Any help, suggestions, comments are welcome.