Detection of peak at the same time

Similar Questions

• Apple Magic Keyboard 2 (2016) detects only no more than 3 keys at the same time!

  Hello. So I don't know if there is a solution to this, but I played on my macbook pro 15 inch 2015 model very well and I was pressing 'x', 'w' + 'shift' + 'space' at the same time and four keys were detected by the game, and it worked. After I while I bought the new magical keyboard 2 (2016) and connected to my laptop. I played the same game and based on the same key combination ('x', 'w' + 'shift' + 'space'), but only 'w' + 'x' + 'space' got detected and played. Is it possible to fix this? Thanks for the future replies!

  If you still use Yosemite, as shown in your profile, you can find (if you look at the box) that the keyboard of Magic 2 is planned for El Capitan.   You should go if you want to get the best out of it.   I can't speak for specific failures, but there have been similar problems with the Magic Mouse 2 where the upgrade it is resolved.

• Read data series and detect the break in series at the same time

  I need to communicate with a serial device that sends messages back, but also sends a break, break, break, break series combo that I need to listen to. I've never worked with before series breaks but the only VI I found which seems to detect pending VISA on event VI with the series Break parameter. I'm not sure that understand how I could detect a break in the series, but also to be reading and writing messages at the same time in the meantime. Isn't this possible?

  If you use multiple loops, I think you can do.  You use 1 loop to check to see if there is data and 1 loop looking for breaks series.  Then use queues, authors of notifications or events to anyone who needs to know what you have experienced.

• USBOTG and Charge at the same time on Stream 8

  To keep this thread as productive as possible and efficient for those who find it useful to:

  Unless you have under your eyes

  1. a schematic representation of the 8 Stream USB port (USB port and battery electric circuit etc.)

  2 source code for the firmware BIOS and kernel that controls the material

  Please DO NOT respond or say "is not possible".  In view of the above is true, you do not have enough information to say '' not possible. ''

  If no one replys with a solution, what he calls not possible by default.

  Also please do not answer to say ' I don't know how "or" but I know how to do anything else that ' is also not that useful.

  An update of the BIOS or other software update may be required by HP, Microsoft or both to offer this feature really intuitive and quite possible.

  And I hope that this thread can be an effort consolidated by all who have the 8 flow to make the necessary changes.  The majority of the other tablet PCs are capable of it.  It seems that only the 8 Stream and a few others have trouble with her.

  ~~~~

  I want the ability to use a simple, inexpensive cable and perhaps standard (with electronic active minimum inside) which allows me to host and to use one or more USB devices on the Stream via its USB port B microphone 8 while this cable can also be connected to a charger standard and charge 8 flow simultaneously.  This means that the cable has a minimum of three connectors.  One of the possible configurations are as follows (apart from the normal charging cable):

  1 cable Micro USB B Male - connect to the stream 8

  2 USB male A - connect to the AC charger (IE one that came with the 8 Stream)

  3. USB A female - one or several connectors to plug into the key of USB data, keyboard, mouse or even a hub.

  Connector # 2. above shall provide a power supply to recharge the 8 Stream via conn. #1 and the power supply for external USB devices via conn. #3 so that they are in use - all at the same time.

  A and if the same cable can act as a normal OTG no charger for when no external power supply is available.  This may necessitate a switch or an electrontics active inside.

  The last part of this goal is unimportant for various reasons.  I wish that HP, the manufacturer of 8 flow, to State in writing good mode necessary to do this, so that other manufacturers or even-it yourself can make maximum use of their tablet HP equipment.

  ~~~~

  The neat thing it will alow a person to do with their tablet, it is to work at home using the Tablet as a desktop PC by connecting a keyboard, mouse, perhaps external screen (with USB to the display adapter) and knit for a long time without time limit prescribed by the battery life because the charger provides energy to all involved.

  If there is only a single connector on the cable #3, then an additional node of coarse had to provide support for these multiple USB devices at the same time.  However, it would be better if there were several #3 connectors integrated in the cable itself.  This would be better as a suitable USB hub also requires its own power.  That an adapter is necessary if the whole thing were integrated into one.

  ~~~~

  I really want answers from anyone who has already accomplished USB OTG delivered with simultaneous load with flow 8. (independent of any published 'proper' way is also welcome)

  Today's date is 2015-01-16.  If in 2015-02-16 (one month), nobody has posted a solution and then starts to bug HP and Microsoft on it's us?

  ~~~~

  Technical training:

  I understand the possibility the tablet software and firmware must take a decision on the manner in which power flows on the power port USB microphone B pins.

  I know that with a proper design of the electronic circuit carring these signals of power inside the Tablet could be sensitive to what is connected and without risk to decide for himself what to do without needing to control software.  For example by testing/detecting periodically differential voltage or current management to see what sides of the connector can supply.

  But this is only one of the many "could bes".

  In addition, this can be no standard regarding the standard USB.  What seems to be actually the case with a lot of cables OTG + fresh, is that physical clues embedded in the cable or charger are used to signal to the Tablet what the situation is.  Then the signal of software/firmware of the Tablet, interprets what the situation is intelligently and responds by flipping the bits of correct hardware control to activate, or deactivate the power flow in the port and also control its direction in or out.

  I'm not familiar with the standard USB.  Maybe I could do more research, if I believed that HP followed with 8 Stream or even the standard covered this situation explicitly.

  But to a certain extent, it seems I'll have to invent something that should be intuitively just like it does with other tablets. Isn't it?  Maybe I'm overthinking, but I can't find any USB OTG + cables load that specify compatibility with 8 HP flow.

  In any case, I was familiar with both methods other use of tablets to send the highest mentioned signal to the hardware/firmware/software of the tablet to the idea that it's time to load / time of OTG or both.

  The first method is a 0 Ohm to 200 ohms short between pin USB A 2 and 3.  This is the bidirectional data differential lines D - and D + respectively.  In data mode, all the data passes back and forth on those lines.  When you load with a cable, it's the charger module that puts this short, not on the cable.  I measured the short on three different Chargers.  It is 0 Ohms on two of them, one of those who are the charger that came with the 8 HP flow.  The others 0 ohms was generic.  The third was for an apple iPad and it measured on 53KOhms.  It's probably not the resistance ohms 0-200, but probably it is impedance termination indicating that there is some intelligent serial port communication in the charger itself.  Leave it to Apple to be different.

  This method is somewhat questionable, as this signaling mode would prevent OTG + fee because it seems unlikely that you will be able to OTG when the data lines are shorted each and overloaded with such low impedance.  I could be wrong on this subject...

  The other method I have seen suggested to work with some tablets and phones other than the 8 stream is too short the USB microphone B pin 5 to Terminal 4 with 0 Ohms to 100 000 Ohms.

  USB B has 5 pins.  USB has only 4.  The extra pin on B moves the GND pin 4 pin 5 pin to and makes pin 4 PIN ID.

  If this signal applies to a drop in the ID pin (4) or in some cases, I saw that she proposed, he runs down with 0 Ohms.

  Dead shorting things always makes me nervous.  If ID is a simple normally high impedance high input, resistance could be used to make voltage well below the low or zero threshold while also preventing the risk of damage when cheat on him with a device that you do not have the diagram for.

  Yet, 100K is a bit high for a 'pull down' in most of the situations that I'm used to.  Even a 10K would be uncertain. A 1 K or 2 K seems reliable enough, but then things are weaker and in know more nowadays low...   All but a dead short but if possible.

  So, it seems possible that the device might be able to "indicate" by the specific value of the resistance, which can be found here.  In other words the resistance is not a pull down but in fact a signature analog ID, in which case the exact value will be crucial. So if this is the case, a guess is not going to work.

  Obviously in such a system as described above, a chip inside the Stream 8 should be responsible to support this information. I hope the 8 Stream has such a chip.

  Probably a register inside this chip would be at all times what the State of the pin ID is a binary number.  All that is needed is for the BIOS to the chip and the registry in it and read this number via the bus to determine what happens to the port. Finally, he would use that signals of info to send the order of material to the electrontics of power set the appropriate direction to take etc.  (and change the State of the icon on the screen of the rude)

  I don't know if the PIN ID method described is a standard USB or not either.

  Eventually, there may be a third way. But I do not suspect that it would be possible with a non-active external device. In any case too complicated for the novice DIY for sure.

  The device would need to act is a kind of extension of bus.  As an active hub.  But she would use the negotiation of data USB serial lines and in addition to reproduce one or more additional USB ports, intelligently inform the tablet to get with the program which is "now we're going to otg and recharge at the same time."

  This requires a smart external device with a processor Inside, no doubt.

  It seems to me that many other tablets have been able achieve avecjoint here the need for a smart external device and thus the flow must also be able to do.

  There is a device that claims to be able to work with the HP Jet 7 and 8 and provides same ethernet and USB and big DVI ports so loads the data stream.  But its expensive because it is active.  Se here:

  http://AMZN.com/B00OVDE0GC

  It's called a "Docking Station".

  A reference to a product that does exactly what I want (possibly without active electronic components) is here:

  http://AMZN.com/B00LTHBCNM

  It's by Kirin and it is a device of type squid with four USB ports.  Precisely, which is my goal.  But read in the comments stream 7 user indicated that he would not be OTG and load, not really clear if it worked as a hub USB OTG or not.  Another evaluator stated that she would not support even a single USB device much less fees of 8 Stream.  This device has a switch.

  I forgot to mention that some 'hackers' have claimed success with other tablets to deceive their devices by using a multi-step process to plug things in.  Usually in general they would get connected Tablet and load first, then they would return a switch or something remove some resistance or the signal was introduced by the first position of the switch. For some reason any Tablet would continue to require. Then the data lines would be free and they would plug in a usb key and it mounts correctly even if the tablet was always in charge.

  It's like the power circuit has a lock which does not allow it to return to the mode "power flow" as long as he still feels the power flows inward regardless of what software it is telling.  Full proposal here.

  These tips seem dubious to me.  Changes in the BIOS could change the way it works.  Also you can not be sure what actually happens if you do not have a schematic representation.  You could damage your tablet.  Many people will support icon in the operating system whether the Tablet is in charge.  But I'm sort of a low-risk guy and my policy is generally indicators of intereperet not to have meaning at all once a device is functioning in a non-standard setting.  Especially when it's something that I did not built and could not fix if I FRY.

  Hypothetical reasoning: tell me what data sensory discs really the State of the charging light screen?  This reflect the bit of hardware control programs actually feeding management and status on the port?  Or does it measure the direction of the flow of power, said in the section of the circuit battery monitoring?  Point - none of us have a schema because it's owner. To really be sure according to the smart electronic hardware, the port must be mode flow under advisement "of power. If it's in a "power flow out" mode and power will be delivered externally as well you wind upward with both power supplies the same power at the wheel nets.  In this case, the two opposing regulators attempting both to drive 5 V can have slightly different voltage calibrations.  That could lead to fighting between them, with more than 100% of their capacity.  For example if you try to regulate 4.95 real V and the other and other attempts to regulate 5.05 V.  Current then flows to the tune of 100 mV / a few milliohms in the cables linking the two.  This may be several amperes. (many)  In other words, like I said: you want the tablet to know that power is coming in don't go out and automatically hitting the internal switches needed for that to happen. Probably the icon should indicate this with precision, but in some wacky situation, he could not. There may be a chance that the icon could indicate the load and still be burning or focusing on some circuits of the tablet or the charger.

  Another thing, I could see that happening is if you play with these reported resistance types enough you might find a resistance value that winds up place the device in an intermittent condition.  In other words it keeps flipping back and forth quickly between OTG and fresh.  It can give the illusion that it works.  You can have marginal communication with your USB devices and battery could even load.  But will still be a lot of stress on the power circuit.

  It is difficult for me to risk a Tablet perfectly well if I don't know exactly what I'm doing.

  If a brave individual makes their own experimentation and verifies that it charges and OTGs and you tell the rest of us, you're a hero.

  Maybe one of you has a good knowledge on the USB standard to have more confidence in such an experience... like what the ID pin 4 REALLY supposed to work for example?

  That's what I know so far.  If you think you can help, thanks in advance, or if this helped you, then your quite welcome.

  It works

  http://Accessories.us.Dell.com/SNA/ProductDetail.aspx?c=us & l = to & CS = 19 & SKU = 470-abes & baynote_bnrank = 0 & baynote_irrank = 0 & ~ CK = baynoteSearch & dgc = CJ & cid = 47997 & lid = 4279734 & acd = 10550055-4485850-eb75dcb47e53437680ed323a1f4885fe

  Evidence

  http://targusblog.com/2014/11/25/how-to-turn-a-99-Tablet-into-a-workstation/

  But it's 4 x the price in Europe

  Have fun

• Is it possible to use iCloud shares photos with the two opening and Photos at the same time?

  Is it possible to use iCloud shares photos with the two opening and Photos at the same time?

  Non - PEAK is not a feature of iPhoto or Aperture - this is new with Photos

  LN

• Questions about serial port read and write at the same time

  Hi I create a user interface for the communication serial port, where there are essentially 2 front panels, where the user enters commands one and the other where the prints of UART is delivered. I thought initially using a state machine but the reading and writing may be independent sometimes and so I can't rely on States. I searched a bit on the forum and he left me even more confused. Help, please.

  (1) in a thread that sessions visa duplicated has been used for writing and reading at the same time, is it recommendable? How will this affect performance?

  (2) essentially when the vi is reading data are it must constantly view as well, however, someone said that it takes too much memory to use shift registers, so how do I go about this? If using a State in queue after the loop of reading it affects the playback loop and be sequential?

  In addition anyway is to move the cursor to the latest data from the indicator

  (3) for the control of the user input, assumes that the user has entered an order in the control and press ENTER, then writing visa is launched, but if it comes in another string and press enter then write must be called again... is - it possible? will detect the previous commands in the control of compensation?

  (4) according to my understand the expectation for the event do not monopolize resources and writing can go in parallel, am I right?

  Thank you. I have attached a very basic vi which took me to the point, but I want to make it more robust. Please help especially in the part of the user interface.

  su_a,

  (1) you can have only one session to a port. Several UART can handle full duplex so performance is not affected.  At flow rates of high data and large amounts of data, buffering and latencies of BONE can become a problem.

  (2) who told you that shift registers using too much memory? Shift registers are usually the best way to transfer data from one iteration to another. String concatenation inside a loop (registry to offset or not) causes the chain to develop and may require re-allocation of memory.  Your VI never clears the string so its cold length become very large.

  Generally, you do not have an active cursor on an indicator.  If you want to always display the most recently received characters and turn on the vertical scroll bar use a property node to keep scrolls to the bottom.  This can be annoying for users if they attempt to manually move the scroll bar and find that the program continues to move it back automatically.

  (3) if the user has changed the value in the chain of command, when he hits enter the modified value event fires.  Simply strike brace does not change the value and does not trigger the event.  Not control need to be erased, but the value that he has to change.  If you want to send the same command again, have a button send a command may be a better choice.

  (4) write is a case of the event.  It is not in parallel with anything.  The structure of the event do not monopolize resources.  The other loop will run while it waits.

  The event loop will not stop when you press the STOP button. Probably it wll take two command: change events of value after JUDGMENT before any loop stops.  Replace the Timeout event (which never expires) with a STOP: value change event and a real wire of this judgment to the Terminal endpoint.  Remove the local variable.  Make mechanical locking when released.

  Lynn

• I use VISA 5.3 for reading my serial device... my standard equipment is WELL this device will send four messages for only one comand I need all four messages to display at the same time in VISA SERIES READ BUFFER

  I use VISA 5.3 for reading my serial device... my standard equipment is WELL this device will send four messages of single command given to this instrument... and I read messages through VISA series READ... during the race, the VI buffer displays the messages individually...  I need all four messages to display at the same time in VISA SERIES READ BUFFER, in order to find more than this block, I should add from the palette of function.

  Disable character of endpoint detection or make four readings where you concantanate simply the strings together.

• How to set up and use two video cards at the same time.

  I have HP Pavilion a6150d desktop under Windows XP SP3 PC. My goal is to be able to use the integrated video card and GeForce 220 video card I just buy at the same time.

  The integrated video card and GeForce video card (connected to the PCI-E) are installed and usable, but the problem is that I think that my computer cannot detect a video at a time card, so I can't use 2 monitors at the same time.  The video only card detects my computer is what I chose as a primer in the BIOS. When you go to the Device Manager display adaptors I can only find an available video card and that's regardless of Setup as primary in the BIOS.

  My GeForce 220 have VGA, DVI and HDMI display connectors, but I don't have that VGA cables. So my only option at the moment is to use my video card GeForce with band single VGA connector and integrated everyone to use my two monitors.

  I hope someone can help me without spending more money...

  "You're not going to be able to use the graphics card integrated Intel and PCIe x 16 graphics card at the same time."

  Thanks Frank, this already answered my question, you help me already by saving my time searching for the fix (since there is NO solution), although it won't save my money I like always your quick response and your support. My monitor is HPw1907 with a DVI connector, so I'll just buy a DVI cable. My other monitor LCD SHARP that have a HDMI and VGA connector so I'll just use the VGA cable in this one.

  So I guess that my simple goal is not achievable using HP Pavilion a6150d. I love HP more than Dell, but it's doable in Dell, so I hope that HP will have way on how to make this thing work in the future.

• Message came up with, "Windows has detected another computer with the same IP address on this netework."

  A message came that said, Windows detected another computer with the same IP address. "... or similar message to one, that could just be the functioning of the laptop for the wireless?

  MurrayJoe:

  > Mean someone has or may have access to my PC or laptop?

  You mentioned a wireless laptop. Do you get this message at home (when your laptop is in communication with your own wireless router), or that you get this message when in a public hotspot?

  If at home, then I would be not too concerned (what security options enabled in your home router?).

  If you get the message while using a public access point, this does not necessarily your computer has been hacked... but it is a warning that you should not ignore. In general, I would not go to any site that has my financial data, or any other sensitive data, a public hotspot. There are too many ways that a public hotspot may be compromised.

  Your original post said that "a message came that said, Windows detected another computer with the same IP address.

  There are several reasons this could happen... some innocent people and some not so innocent.

  If your network is configured for the most common way, then your router uses a feature called Dynamic Host Configuration Protocol (DHCP). You can read about DHCP here...

  http://en.Wikipedia.org/wiki/Dynamic_Host_Configuration_Protocol

  Basically, when a device on your home network needs an IP address, he asks your router and your router assigns an IP address... technically, "rents" the router address for a given period (one day). Once this period has elapsed, the device must 'renew lease'.

  DHCP stops you from the hassle of having to assign a static IP address to each device on your network and then don't forget to retrieve that meet if/when a device are removed from your network.

  Sometimes the process DHCP can be confused and assign the same address on multiple devices. If/when this happens, communication between devices on your home network may be confused. Windows is smart enough to detect that another device on your home network has the same address as the computer where Windows is currently running..., but Windows can not solve the problem.

  You can determine the IP address of the computer that is running Windows (and posted the message you saw)... by entering "ipconfig" (without the quotation marks) at a command line prompt. Then you can check the IP addresses of all devices on your network until you find the other devices with the same IP address. Then you could say either every device to get a new IP address of the router (or restart the device). Alternatively, you can try just stating the computer that is running Windows to get a new IP address (by first entering "ipconfig/release" then "ipconfig / renew" in the command-line invite him... all orders without the quotes).

  But since you said that you are not very tech savvy, my first suggestion was the easiest... just shut everything in your network, and then restart one at a time by starting with your ISP device, router, and other devices. If the problem persists after that, then more troubleshooting (as described in the previous paragraph) would be necessary.

  I hope this helps to clarify the issue for you. If you have any questions, please post them and I'll try to answer.

• When using my computer, all applications and the windows are closed at the same time, got disconnected and the computer turns off as if someone stops manually.

  Original title: it's a virus that's causing this?

  It happened a few times now. While I use my computer, all applications and the windows are closed at the same time, I am disconnected and the computer is off, as if someone manually stops the computer. I turn on the computer and log in and everything seems to be okay. No data deleted, not that I could find and detect anyway. One day when I turned on the computer, it run chkdsk before doing the usual startup. I use the computer for 2 years and this is the first time, she never did a chkdsk on its own. I used Microsoft Essentials and no viruses were found.

  Should I worry?

  Hello

  You can read the following article and try to download the Microsoft Safety Scanner and perform a full scan on your computer and check.

  Microsoft safety scanner

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Check if there are logs of events related to the issue in the event viewer which may help us to solve the problem of the:

  What are the information contained in the logs of the event (Event Viewer)?

• Can't push button and move the mouse pads at the same time hp envy 15?

  Cannot press the keyboard and move my mouse at the same time, the stops of mouse moving on the screen, then after a few seconds, then thaws it and it can be moved again.

  HP Envy 15-3012tx, Windows 7 64 bit, have not updated, there quite yet new at the beginning of the year

  I also found this to play games almost unbearable, even if I found the source of the problem is the touchpad by using the feature called "palm detection.

  How I fixed it for my computer hp envy laptop was that...

  Control Panel > hardware and audio > synaptics clickpad v.1.1 > parameters > "smart sense" > click the gears of the 'line of smart sense' > the upper off wheel

• Micro security: several apps at the same time registration?

  Anyone know if it is possible for multiple applications 3rd party capture audio from the microphone of the device at the same time? I want to assure you that my app is only the audio capture. Has anyone tried detect if other applications use the microphone?

  If multiple applications can register at the same time, this could be a pretty serious security concern. See more here:

  http://www.NET-security.org/secworld.php?id=13015

  Thank you.

  A second request to try to use the microphone would get an error message saying that it is not available.

• Windows has started to put some files in two places at the same time, will appear in some programs

  Hello

  in the last two weeks, I noticed that Windows (I use Windows 7) began to act up with its allocation record. First of all, I noticed that a new folder I created for some music files was not detected when I tried to open the file in a music editing program (Adobe Audition). If I created a new folder in a different location and copied the files into that, suddenly hearing would recognize the folder. Change a few days I noticed that in addition to this, when I copied a disc into my computer, after you select a new folder for the files to copy, Windows would create a second copy mirror of the folder and the files and place it in another location not of my choice (this all happens within my music library folder). Some files that I had cut my folder "work on", to stick to my folder to archive tips that did it, and windows in two copies of each of them - one where I had pasted it and other oddly in a separate folder completely in my archives. For some reason any Windows decided to put copies ghosts of several things in this folder without special report. So, if I change the files in a folder, they are automatically changed on the other; If I try to delete a copy of this file, it removes the two; and if I try to cut and paste the lot assigned folder and put it where it should be back (IE if there is already the original copy) Windows says it can't do that because the destination file matches the location of origin. I don't know how to remove these files has doubled up foreign, which create a lot of confusion trying to figure out where my files and which ones to change. I can't find any way or return of Windows to its appropriate classification system, including maximum until recently had none of these problems.

  Music library is not a folder, it's just a definition of research.

  Libraries are really just XML files that define search criteria.

  The real essentials you need to know is that libraries are not records.  They are really just a quick search of several places.  Try this: right click on the document library and select Properties.  This will tell you where the library is looking.  Whenever you open the document library, it performs an instant analysis of these places and tells you what he found.  Is not additional copies files, it's just search results. If you delete something, you remove the one and only original, everywhere where it is.

  You might ask "well, what's the point of a library?  I'm glad you (perhaps) asked.  The reason is you have a lot of places.  Take me for example.  I have some movies on my hard drive.  I have more moves on an extra drive (they will all take place on the main drive).  In addition, my roommate has a few movies on his drive.  With a library, I have a library of videos that research on all drives and gives me a single view combined all our movies instantly.  Now I can see all my films in my library at the same time, no matter which disc they are on.

  The files are not duplicated or moved, you see just a list of them, such as a telephone directory or the Google search results.

• Press the 2 buttons at the same time

  Hello

  I thought I was doing a game of Pinball this morning.  Because the PlayBook a 4-point multitouch, is possible to detect the pressure/holding a button left flipper, a right flipper button or both flippers at the same time.  How about the two buttons a fraction of the second part?  QNX is a real-time operating system, but I have not found this type of control in the AIR SDK.

  Harry

  There should be no problem to do that, but I think you want to use the flash.ui.Multitouch API

  Here's a video that shows how to do this, but you will end by edit it just follow your TouchEvents rather than MouseEvents...

  In response to Touch raw data

  Hope that helps

• In Windows 7 Action Center, MSE, and Windows Defender convertible 'ON' at the same time?

  In the center of Action of Windows 7, Microsoft Security Essentials (MSE) is enabled.  I tried to turn on Windows Defender 'manually' and get a status of "OFF"OBSOLETE"? that quickly toggles back and forth

  I'm trying to maximize my options "malicious."  I have NOT tried turning 'OFF' MSE to see if Windows Defender will be 'ON '.

  My real question is, can MSE and Windows Defender, being 'ON' at the same time or are mutually?

  A "full scan" using MSE detected the following malicious program "trojan:Win32 / Tracur.AV". I immediately deleted it. I think it's GONE!

  My "quick" weekly scans did not detect this malware. What a scare on my new laptop TOSHIBA P750.

  Now I take the time 'always' do a full scan.

  Help

  Hello

  Welcome to the Microsoft community.

  If you use Microsoft Security Essentials, there is no need to use Windows Defender. You can disable that and just let Microsoft Security Essentials run things.

  You should only use an antivirus program. using several programs at the same time will cause problems.

  Please refer to this link:

  http://answers.Microsoft.com/en-us/protect/Forum/MSE-protect_start/Windows-Defender-and-Microsoft-Security-Essentials/5309cb8d-02e1-40E8-974f-0dcedb9ab9fd

  It will be useful.

  Let us know if you have any questions about Windows and we will be happy to help you.