DHCP on 62xx and switches 28xx
I'm putting up a VoIP system and fight with the network config. I have a mixed environment of 62xx series and 28xx series switches. I created a VLAN for voice and uses the default VLAN for data. VLAN routing on the l3 switch works fine. I can ping between subnets without any problem.
Working with intellectual property, as the IP phones will get an address on the subnet of data, then restart and vlan tag allows to obtain the IP address of the subnet of the voice of any port on any switch. But if I put the pvid on any port to the vlan voices, machines Windows still get DHCP on the vlan, but IP phones will not, they will receive only an address so firstly through the subnet data. My voice switches also lose communication entirely, when statically defined with an address of subnet voice and connected to a port with pvid voice vlan.
Through the subnet of data to get an address is no big deal, but being not not able to put my voice switches on the subnet of voice is a problem. I will freely admit that I know just sort of what I do. Any help or advice would be greatly appreciated.
Hello
Here is the recommended method to configure the data and phone. http://www.Dell.com/downloads/global/products/PWCNT/en/pwcnt_voice_VLAN_support.PDF
Data is found in the VLAN no marked native and the voice in a VLAN tagged.
Tags: Dell Switches
Similar Questions
-
Configure the DHCP on the router and switch
Good afternoon
I'm trying to set up DHCP using CLI on a 2610 router and switch 2950. With my current config, the host at the end of the switch (set to receive ip via DHCP) does not have anything assigned. Here are a few shows:
Router:
Router_1 #show ip int br
Interface IP-Address OK? Method State Protocol
192.168.10.1 FastEthernet0/0 YES manual up up (leading to pass)
Serial0/0 YES no not defined administratively down down
Serial0/1 no YES not defined administratively down down
Ethernet1/0 YES no not defined administratively down down
Ethernet1/1 no YES not defined administratively down down
Ethernet1/2 no YES not defined administratively down down
Ethernet1/3 no YES not defined administratively down downRouter_1 #show ip dhcp pool
Pool acer_pool:
Brand usage (up/down): 100 / 0
Size of the subnet (first/next): 0 / 0
Total addresses: 254
Rental addresses: 0
Waiting for the event: no
subnet 1 is currently in the pool:
Range of addresses IP of Current index leased addresses
192.168.10.1 192.168.10.1 - 192.168.10.254 0Switch:
Switch_1 #show ip int br
Interface IP-Address OK? Method State Protocol
Vlan1 unassigned YES NVRAM up up
FastEthernet0/1 no YES unset upward, upward (leading to the router)
FastEthernet0/2 not assigned YES unset down down
FastEthernet0/3 not assigned YES unset down down
FastEthernet0/4 not assigned YES unset down down
FastEthernet0/5 not assigned YES unset down down
FastEthernet0/6 not assigned YES unset down down
FastEthernet0/7 not assigned YES unset down down
FastEthernet0/8 not assigned YES unset down down
FastEthernet0/9 no YES unset down down
FastEthernet0/10 not assigned YES unset down down
FastEthernet0/11 no assigned YES unset down down
FastEthernet0/12 not assigned YES unset down down
FastEthernet0/13 not assigned YES unset down down
FastEthernet0/14 not assigned YES unset down down
FastEthernet0/15 no assigned YES unset down down
FastEthernet0/16 not assigned YES unset down down
FastEthernet0/17 no assigned YES unset down down
FastEthernet0/18 no assigned YES unset down down
FastEthernet0/19 not assigned YES unset down down
FastEthernet0/20 not assigned YES unset down down
FastEthernet0/21 no assigned YES unset down down
FastEthernet0/22 YES no assigned unset upward, upward
FastEthernet0/23 not assigned YES unset down down
FastEthernet0/24 no assigned YES unset down downWhat other info I can provide to solve this problem?
Thank you.
I think that you need to configure the router-on-a-stick.
Post your DHCP configuration.
-
right click on google for, open a new tab and switch to it immediately
When I select a Word and choose in google for right click, firefox opens a new tab and switch to it immediately. I don't want firefox to go immediately to the tab I maybe other words to highlight and click on google search for it.
so, how do you not move immediately to the tabs in firefox open the right click on google for? also as a note in my options on the tab firefox immediately switch to tab is disabled and I use the latest version.
You can set the Boolean pref browser.search.context.loadInBackground true on the topic: config page.
-
can I have both versions installed and switch between the two
Can I have two different versions of firefox are installed and switch between them? If so, how do I set up.
Yes, I have several versions of firefox are installed. Firefox 3.6 is always taken in charge and course, there is the beta, the Aurora and the roads every night. I'm guessing that the other default channels install in clean places out there rather than overwrite your current installation, if not choose the custom installation option.
This is something advanced, generally used by developers etc.
CARE do not uninstall and take an option to remove personal settings, but that is written, as that attempts to remove all the profile data for all versions Firefox installed, you will lose the passwords and bookmarks etc..
Use unique profiles - where Firefox stores your bookmarks, passwords and other user data for each version, or you will have problems.
-
How to switch on and Switch Off LED using lab view
How to switch on and Switch Off LED using lab view, I need to Switch on and off material LED, not the soft LED.
I need to know the different ways to Switch On and Off the LED
Hello
I need to control the LED on my laptop which is to have labview, kindly tell the different ways that my laptop a serial port, is possible to control using that.
-
difference between hubs and switches
What is the difference between hubs & switches?
Hello and welcome to the forums!
There is a subject existing publication from years back. Please click the link below.
You can also try to search for similar topics by typing the keyword in the search field above the page.
-
What is a DHCP client address and what is an ISP?
Try to connect Tivo w / a wireless connector for my computer instead of using the phone line. TiVo's request for a DHCP client address and Pack International customer
Hello
The DHCP Dynamic Host Configuration Protocol () is a protocol for network configuration for hosts on networks IP (Internet Protocol). Computers that are connected to IP networks must be configured before it can communicate with other hosts. The essential information needed are an IP address and a default route and the routing prefix. DHCP eliminates the manual task by a network administrator. It offers a central database of devices that are connected to the network and eliminates duplicate resource assignments.
An ISP (ISP) is an organization that provides access to the Internet.See the following link:
Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
http://support.Microsoft.com/kb/928233Note: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry
-
Need router and switches for simple network tips...
I have to get a new router and switch to an office with 9 computers, 1 printer, and a server. They are all Mac computers. Two Mac computers are running Windows XP through Parrallels (not sure if it matters). All computers have just need access to the Internet (through the router), access to the printer and 5 of them on the server. A few more important details: the router will be located about a quarter of a mile away (where we could get a broadband Internet access) but will have a fiber optic cable running to the office, where will be the selector. In the building off site where the router, we would like to have a backup disk to send important files at the end of each day (or set up to do this automatically later). The optical fiber has capacity of the card. We want that the router must be connected only (wireless). Any suggestion that router and switch combo would be enough? Thank you!
You can use a RVS4400 router that has a gigabit capacity with 4 ports, connected to the gigabit switch.
-
User profile runs as an administrator for the daily work and this account is corrupted and switch every time on my laptop, just open a temp file (created), I downloaded a driver to run my cell phone as a modem while he is on vacation. and the problem started after downloading this software,
Hi johnnyroque
Thanks for posting on Microsoft Answers.
Try to use the following steps to enable the built-in Administrator account and further, then the steps and links to fix a corrupted profile.
Please start on the mode of the Windows recovery environment (WINRE).
-To start the computer into WinRE mode, insert the Vista CD in the CD tray, restart the computer.
-When you are prompted to "press any key to boot from the CD-ROM..." Press ENTER.
-Select the language by default, click Next.
-Select "repair your computer".
http://www.Flickr.com/photos/freeed/363935713/in/set-72157594490796701/
-Select command prompt, and then type the following commands:NET user administrator / Active: Yes
NET user {user account name} {new user password}Note: Please enter the user name and the password without the braces of the flower.
-Restart the computer normally.//////////////////////////////////////////////////////////////////////////////
To fix a see corrupted profile link below:
http://windowshelp.Microsoft.com/Windows/en-us/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspxPlease post back and let us know if it helped to solve the problem - thanks Ken
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think. -
Order of port re-auth authentication and switch / stop of the session
Hi all
We are implementing an ISE (1,4) and met regarded questions on the agenda of the authentication and a stop of the session after posture in line. We got mab, dot1x as authentication order (priority of authentication is set to dot1x, mab). We have configured a reauthentication in the ports of the switch. Windows uses begging all-connect NAM (see 4.2) to dot1x and posture. During the re-authentication, either all-connecting NAM or switch does not start an eapol start and switch allows the session to the MAB, where - as when seen dot1x and mab authentication switch order generates eapol start. The switches are 3750 (15.0 (2) SE8).
Any possibility we could force the switch/NAM agent sent an eapol start during re-auth?
Regarding the posture, posture once conform for an endpoint (after dot1x authentication passes) following a judgment of the ISE manual session for an endpoint, switch creates a new session in ISE changes and switch the State of the unknown port to posture. Posture ise AC client still shows status of complaint of posture in the endpoint. It seems do not know about the stop of the session. During NAM endpoint agent session performs a re-auth component however posture remains unchanged "in line".
Does anyone have experience this problem?.
Thanks in advance.
Concerning
GA
Hi Gaj-
I had the similar problem in the past and for setting the following attribute:
Termination-action-AVPair attribute modifier = 1
Give that a go and let us know if you still have any questions.
Thank you for evaluating useful messages!
-
I use a Brother MFC-7420. Usually, it works under Windows 7, but from time to time (maybe 1 in 20 times) he will not print and I have to unload the coil and switch off the printer before Relighting. It is not always the case, but it is enough times to be a nuisance.
Ideas, people?
Hello
This problem occurs when you make changes to the computer?
Method 1: Diagnose and automatically fix problems printing and printer
http://support.Microsoft.com/mats/printing_problems/
Method 2: Refer to this link: I can not print from my computer via the USB port.
If you have problems, I haveinstall updated printer drivers, see this link:
http://www.brother-USA.com/downloads/default.aspx?PgId=5&R3ModelID=MFC7420Refer to this: update the drivers for hardware that does not work properly.
http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly
See also: printer in Windows problems
http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-WindowsI hope this helps!
-
I have LR 6 (upgrade LR 5and4) installed on Windows PC and switch to Mac. It will not install on Mac since the earlier version is installed. Is there a solution?
Update should allow you to enter the serial number of the previous version during the installation
If this does not work, you must communicate directly with Adobe
Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">===>
Don't forget to stay signed with your Adobe ID before accessing the link below
Creative cloud support (all creative cloud customer service problems)
-
Upgrade CS5 CS6 and switching operating systems
I currently own the CS5 Production Premium Student Edition for PC, and I plan (commercial) CS6 upgrade when it becomes available. Now I work mainly on a Mac and am tired of dual-boot to use my Adobe products, so I wonder if there will be problems with the upgrade and the choice of the OS from PC to Mac switch at the same time. I've seen some old discussions regarding these issues individually, but they applied to previous editions of CS. Any help, ideas or suggestions are welcome!
Hi Tralmek,
There should not be any problem in upgrading and switching of the operating system.
If you want to upgrade to CS5.5 or CS6 MAC CS5 Win, you can do. Its called Cross-platform upgrade.
But as mentioned Bob, you should contact adobe for this. It can be done online from the adobe Web site.
For the best support, I recommend our chat support at http://adobe.ly/yxj0t6. Our chat representatives can provide a personalized experience to solve the problem you described.
Concerning
Arpit
-
DHCP SNOOPING TO THE SWITCH OF CISCO SMALL BUSINESS SF200-48
Please help me. I need to know if the dhcp snooping is available in cisco firmware version 1.3.7.18.
Hi Bonnie, as I know DHCP snooping is not on the SX200 switch. I am also unable to find documentation in Administrator's guide and release notes not stating that it is.
-
Hello
We run 3xWLC controller with 800 AP using ISE 1.2 for authentication wireless 802. 1 x. I was looking in the config of the ISE and notice of 400 edge cheating only 2x2960s are configured with 802. 1 x (ISE RADIUS config) and SNMP and only 2 of the port is 2 ap tie with swtich remaining ports.and the 3XWLC in network devices.
I do not understand how an access point is to do this work (802.1 x) because it is location on different site and people are connecting to various different locations. ISE almost run/do 11 876 profiled ends.
version 12.2
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$ fokm$ lesIWAaceFFs.SpNdJi7t.
!
Test-RADIUS username password 7 07233544471A1C5445415F
AAA new-model
Group AAA dot1x default authentication RADIUS
Group AAA authorization network default RADIUS
Group AAA authorization auth-proxy default RADIUS
start-stop radius group AAA accounting dot1x default
start-stop radius group AAA accounting system by default
!
!
!
!
AAA server RADIUS Dynamics-author
Client 10.178.5.152 server-key 7 151E1F040D392E
Client 10.178.5.153 server-key 7 060A1B29455D0C
!
AAA - the id of the joint session
switch 1 supply ws-c2960s-48 i/s-l
cooldown critical authentication 1000
!
!
IP dhcp snooping vlan 29,320,401
no ip dhcp snooping option information
IP dhcp snooping
no ip domain-lookup
analysis of IP device
!
logging of the EMP
!
Crypto pki trustpoint TP-self-signed-364377856
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 364377856
revocation checking no
rsakeypair TP-self-signed-364377856
!
!
TP-self-signed-364377856 crypto pki certificate chain
certificate self-signed 01
30820247 308201B 0 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
2 060355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30
69666963 33363433 37373835 36301E17 393330 33303130 30303331 0D 6174652D
305A170D 2E302C06 1325494F 03550403 32303031 30313030 30303030 5A 303031
532D 5365 6C662D53 69676E65 642D 4365 72746966 69636174 652 3336 34333737
06092A 86 4886F70D 01010105 38353630 819F300D 00308189 02818100 0003818D
B09F8205 9DD44616 858B1F49 A27F94E4 9E9C3504 F56E18EB 6D1A1309 15C20A3D
31FCE168 5A8C610B 7F77E7FC D9AD3856 E4BABDD1 DFB28F54 6C24229D 97756ED4
975E2222 939CF878 48D7F894 618279CF 2F9C4AD5 4008AFBB 19733DDB 92BDF73E
B43E0071 C7DC51C6 B9A43C6A FF035C63 B53E26E2 C0522D40 3F850F0B 734DADED
02030100 01A 37130 03551 D 13 6F300F06 0101FF04 05300301 01FF301C 0603551D
11041530 13821150 5F494D2B 545F5374 61636B5F 322D312E 301F0603 551D 2304
18301680 1456F3D9 23759254 57BA0966 7C6C3A71 FFF07CE0 A2301D06 03551D0E
04160414 56F3D923 75925457 BA09667C 6C3A71FF F07CE0A2 2A 864886 300 D 0609
F70D0101 5B1CA52E B38AC231 E45F3AF6 12764661 04050003 81810062 819657B 5
F08D258E EAA2762F F90FBB7F F6E3AA8C 3EE98DB0 842E82E2 F88E60E0 80C1CF27
DE9D9AC7 04649AEA 51C49BD7 7BCE9C5A 67093FB5 09495971 926542 4 5A7C7022
8D9A8C2B 794D99B2 3B92B936 526216E0 79 D 80425 12B 33847 30F9A3F6 9CAC4D3C
7C96AA15 CC4CC1C0 5FAD3B
quit smoking
control-dot1x system-auth
dot1x critical eapol
!
pvst spanning-tree mode
spanning tree extend id-system
No vlan spanning tree 294-312,314-319,321-335,337-345,400,480,484-493,499,950
!
!
!
errdisable recovery cause Uni-directional
errdisable recovery cause bpduguard
errdisable recovery cause of security breach
errdisable recovery cause channel-misconfig (STP)
errdisable recovery cause pagp-flap
errdisable recovery cause dtp-flap
errdisable recovery cause link-flap
errdisable recovery cause FPS-config-incompatibility
errdisable recovery cause gbic-invalid
errdisable recovery cause psecure-violation
errdisable cause of port-mode-failure recovery
errdisable recovery cause dhcp-rate-limit
errdisable recovery cause pppoe-AI-rate-limit
errdisable recovery cause mac-limit
errdisable recovery cause vmps
errdisable recovery cause storm-control
errdisable recovery cause inline-power
errdisable recovery cause arp-inspection
errdisable recovery cause loopback
errdisable recovery cause small-frame
errdisable recovery cause psp
!
internal allocation policy of VLAN ascendant
!
!
interface GigabitEthernet1/0/10
switchport access vlan 320
switchport mode access
IP access-group ACL-LEAVE in
authentication event fail following action method
action of death server to authenticate the event permit
living action of the server reset the authentication event
multi-domain of host-mode authentication
open authentication
authentication order dot1x mab
authentication priority dot1x mab
Auto control of the port of authentication
periodic authentication
authentication violation replace
MAB
dot1x EAP authenticator
dot1x tx-time 10
spanning tree portfast
spanning tree enable bpduguardinterface GigabitEthernet1/0/16
switchport access vlan 320
switchport mode access
IP access-group ACL-LEAVE in
authentication event fail following action method
action of death server to authenticate the event permit
living action of the server reset the authentication event
multi-domain of host-mode authentication
open authentication
authentication order dot1x mab
authentication priority dot1x mab
Auto control of the port of authentication
periodic authentication
authentication violation replace
MAB
dot1x EAP authenticator
dot1x tx-time 10
spanning tree portfast
spanning tree enable bpduguard
interface GigabitEthernet1/0/24
switchport access vlan 320
switchport mode access
IP access-group ACL-LEAVE in
authentication event fail following action method
action of death server to authenticate the event permit
living action of the server reset the authentication event
multi-domain of host-mode authentication
open authentication
authentication order dot1x mab
authentication priority dot1x mab
Auto control of the port of authentication
periodic authentication
authentication violation replace
MAB
dot1x EAP authenticator
dot1x tx-time 10
spanning tree portfast
spanning tree enable bpduguard
!
interface GigabitEthernet1/0/33
switchport access vlan 320
switchport mode access
IP access-group ACL-LEAVE in
authentication event fail following action method
action of death server to authenticate the event permit
living action of the server reset the authentication event
multi-domain of host-mode authentication
open authentication
authentication order dot1x mab
authentication priority dot1x mab
Auto control of the port of authentication
periodic authentication
authentication violation replace
MAB
dot1x EAP authenticator
dot1x tx-time 10
spanning tree portfast
spanning tree enable bpduguard
interface GigabitEthernet1/0/34
switchport access vlan 320
switchport mode access
IP access-group ACL-LEAVE in
authentication event fail following action method
action of death server to authenticate the event permit
living action of the server reset the authentication event
multi-domain of host-mode authentication
open authentication
authentication order dot1x mab
authentication priority dot1x mab
Auto control of the port of authentication
periodic authentication
authentication violation replace
MAB
dot1x EAP authenticator
dot1x tx-time 10
spanning tree portfast
spanning tree enable bpduguard
!
interface GigabitEthernet1/0/44
switchport access vlan 320
switchport mode access
IP access-group ACL-LEAVE in
authentication event fail following action method
action of death server to authenticate the event permit
living action of the server reset the authentication event
multi-domain of host-mode authentication
open authentication
authentication order dot1x mab
authentication priority dot1x mab
Auto control of the port of authentication
periodic authentication
authentication violation replace
MAB
dot1x EAP authenticator
dot1x tx-time 10
spanning tree portfast
spanning tree enable bpduguard!
interface GigabitEthernet1/0/46
switchport access vlan 320
switchport mode access
IP access-group ACL-LEAVE in
authentication event fail following action method
action of death server to authenticate the event permit
living action of the server reset the authentication event
multi-domain of host-mode authentication
open authentication
authentication order dot1x mab
authentication priority dot1x mab
Auto control of the port of authentication
periodic authentication
authentication violation replace
MAB
dot1x EAP authenticator
dot1x tx-time 10
spanning tree portfast
spanning tree enable bpduguardinterface GigabitEthernet1/0/48
switchport access vlan 320
switchport mode access
IP access-group ACL-LEAVE in
authentication event fail following action method
action of death server to authenticate the event permit
living action of the server reset the authentication event
multi-domain of host-mode authentication
open authentication
authentication order dot1x mab
authentication priority dot1x mab
Auto control of the port of authentication
periodic authentication
authentication violation replace
MAB
dot1x EAP authenticator
dot1x tx-time 10
spanning tree portfast
spanning tree enable bpduguard
!
interface GigabitEthernet1/0/49
Description link GH
switchport trunk allowed vlan 1,2,320,350,351,401
switchport mode trunk
MLS qos trust dscp
IP dhcp snooping trust
!interface GigabitEthernet1/0/52
Description link CORE1
switchport trunk allowed vlan 1,2,29,277,278,314,320,401
switchport mode trunk
MLS qos trust dscp
IP dhcp snooping trust
!
!
interface Vlan320
IP 10.178.61.5 255.255.255.128
no ip-cache cef route
no ip route cache
!
default IP gateway - 10.178.61.1
IP http server
IP http secure server
IP http secure-active-session-modules no
active session modules IP http no
!
!
Access IP extended ACL-AGENT-REDIRECT list
deny udp any any domain eq bootps
permit tcp any any eq www
permit any any eq 443 tcp
IP extended ACL-ALLOW access list
allow an ip
IP access-list extended by DEFAULT ACL
allow udp any eq bootpc any eq bootps
allow udp any any eq field
allow icmp a whole
allow any host 10.178.5.152 eq 8443 tcp
permit tcp any host 10.178.5.152 eq 8905
allow any host 10.178.5.152 eq 8905 udp
permit tcp any host 10.178.5.152 eq 8906
allow any host 10.178.5.152 eq 8906 udp
allow any host 10.178.5.152 eq 8909 tcp
allow any host 10.178.5.152 eq 8909 udp
allow any host 10.178.5.153 eq 8443 tcp
permit tcp any host 10.178.5.153 eq 8905
allow any host 10.178.5.153 eq 8905 udp
permit tcp any host 10.178.5.153 eq 8906
allow any host 10.178.5.153 eq 8906 udp
allow any host 10.178.5.153 eq 8909 tcp
allow any host 10.178.5.153 eq 8909 udp
refuse an entire ip
Access IP extended ACL-WEBAUTH-REDIRECT list
deny ip any host 10.178.5.152
deny ip any host 10.178.5.153
permit tcp any any eq www
permit any any eq 443 tcpradius of the IP source-interface Vlan320
exploitation forest esm config
logging trap alerts
logging Source ip id
connection interface-source Vlan320
record 192.168.6.31
host 10.178.5.150 record transport udp port 20514
host 10.178.5.151 record transport udp port 20514
access-list 10 permit 10.178.5.117
access-list 10 permit 10.178.61.100
Server SNMP engineID local 800000090300000A8AF5F181
SNMP - server RO W143L355 community
w143l355 RW SNMP-server community
SNMP-Server RO community lthpublic
SNMP-Server RO community lthise
Server SNMP trap-source Vlan320
Server SNMP informed source-interface Vlan320
Server enable SNMP traps snmp authentication linkdown, linkup cold start
SNMP-Server enable traps cluster
config SNMP-server enable traps
entity of traps activate SNMP Server
Server enable SNMP traps ipsla
Server enable SNMP traps syslog
Server enable SNMP traps vtp
SNMP Server enable traps mac-notification change move threshold
Server SNMP enable traps belonging to a vlan
SNMP-server host 10.178.5.152 version 2 c lthise mac-notification
SNMP-server host 10.178.5.153 version 2 c lthise mac-notification
!
RADIUS attribute 6 sur-pour-login-auth server
Server RADIUS attribute 8 include-in-access-req
RADIUS attribute 25-application access server include
dead-criteria 5 tent 3 times RADIUS server
test the server RADIUS host 10.178.5.152 auth-port 1812 acct-port 1813 username test-RADIUS 7 key 03084F030F1C24
test the server RADIUS host 10.178.5.153 auth-port 1812 acct-port 1813 username test-RADIUS 7 key 141B060305172F
RADIUS vsa server send accounting
RADIUS vsa server send authenticationany help would be really appreciated.
I'm not sure that completely understand the question; But if LSE is only political wireless, then none of the wired switches need any configuration of ISE.
Access points tunnel all wireless traffic to the WLC on CAPWAP (unless you use FlexConnect). This is the configuration 802. 1 x on the WLC that implements policies defined in ISE.
Switches wired never need to act as an access network (n) device and so do not need to be defined in ISE unless or until you want to apply policies of ISE for wired devices...
Maybe you are looking for
-
How to stop automatic .part file downloading when I run firefox
When I start Firefox, the Firefox menu bar, slowly stresses green as it downloads a large file. I don't want to download this file, when I close FF I can remove the .part file is created, but when I launch FF again, he recreates the .part and the cyc
-
Impossible to update Shockwave Flash plugin
I'm only updating Shockwave Flash because the plugin page says to do so; Otherwise, I have no problems. The sequence of update I'm having problems is different from those described by others:(1) check the updates of the plugin: Shockwave Flash 11.1 r
-
Tuesday night, I downloaded and installed the latest security update. On Wednesday morning at the restart, AVG Anti Virus intercepted a few Trojans and several files of phishing. I then proceeded to power work and tried to open TrueCrypt, which conta
-
The appeal of LabVIEW VI of Python
Hi Ppl, I'm calling python LabVIEW VI using LabVIEW ActiveX or the LabVIEW run engine of ActiveX that can be enabled in the advanced options of the application builder. The problem that I am facing is: I use the VirtualInstrument.Call () method to ru
-
Explorer.exe freezes when Windows XP starts. Programs do not run but clickable.
Start Windows XP.Click on I want to open an account.Type password.Windows desktop with icons appears. Start a hourglass when scrolling on her menu.Frozen, you won't fix. The Task Manager, end Explorer.exeRun Explorer.exeFreezes again but clickable fo