diagnostic data export error

Similar Questions

• Data export Error exporting data databae

  Hello. IAM getting the error when you export data from database. the error is
  
  "Export data for June 3, 2009 09:41:20 IST failed.
  : Error network 1042013 [10054]: cannot receive data
  "Error: network error 1042012 [10054]: can not send data.
  
  
  Any clue?
  
  Essbase system 9 (9.3.1)
  
  Thank you and best regards,
  Srini

  There are the onl; there both times I was not able to get an export of work
  1. when all the dimensions of the database have been set as sparse. A database apparently needing at least a dense export dimension
  2. If the .pag file was corruption. You can run a database of audit to check this and try to fix it, there are problems

• How to allow to export diagnostic data?

  Hi, can you tell me how I can give access to the export of diagnostic data in the CR?

  I have a few administrator and they need to open a Support request, but every time they ask me (super administrator) to generate the diagnostic data file.

  I would like to give them this opportunity, then, how can I do?

  
  Best regards

  I'm closing a bit.  I created a Global custom and only defined role - Diagnostics.  The role has been defined to the host and cluster level.  However, the user can run a bundle of diagnosis on the whole VI, not only their datacenter.

• 0X0000007A (KERNEL DATA INPAGE ERROR)

  Hello, I got a screen blue error during the game or just overall being on my pc, but it seems to happen more when I have the game. The code is '0x0000007a (KERNEL DATA INPAGE ERROR)' I did 3 bugs so far.

  1. CHKDSK C: /F /R (http://goo.gl/cQCQj2)

  2 memory diagnostic tool (https://neosmart.net/wiki/0x0000007a-kernel-data-inpage-error/)

  3. fix (when I tried fix it says update applicable to your computer)

  

  These accidents are called BCC116 and are associated with your video subsystem.  Please follow the instructions of this wiki

  

• Type activity data export failed "FormSubmit"

  Hi all

  I try to export activity outside by the API data in bulk.

  But when you use the activity type "FormSubmit", I get "error" status of the synchronization with message as follows:

  [{'count': 0, 'converted': "\/","message":"There \/Date (1426236500847) was a converted l'export.","severity":"error","statusCode":"ELQ-00107","syncUri":"/syncs/64770"},{"syncUri":"/syncs/64770","count":0,"severity":"information","statusCode":"ELQ-00101","message":"Sync to sync 64770 processing error, resulting in a status.","createdAt":"\/Date (1426236500847) error" \ / ""}]

  Other types of activities work well.

  Any suggestions?

  Thank you

  Biao

  I have problems with FormSubmit as well.  For some reason, there is a massive amount of duplicates in FormSubmit, causing the number to go above 5 million documents.  I don't have these problems with any other activity, just FormSubmits.

• SOUL 2014 export error. No update of the first sequence.

  It seems that queuing sequences of Premiere Pro to SOUL via Ctrl + M is forever broken because creating to hang and hang on the dialog "export media. This has been broken for several months. I talked to developers with no resolution to this. For this reason, I now can only export projects by dragging footage on to SOUL first. It worked fine until a few days ago.

  What happens now is that SOUL gets partially thanks to encode a video and then hangs and fails encoding. I get the super useful

  19/12/2014 15:25:14: encoding failed

  -------------------------------------------------------

  Export error

  Movie compilation error.

  Unknown error.

  I created new sequences with the same media, removed 3rd party audio plugins, flying over all the images to another drive, tried to encoded in a different format such as AVI, and I tried to set the encoding to save them on several disks. It will always fail at the same point. It seems to hang and fail on the clips I created in AE, who travelled using JPEG. MOV. I tried to make the clip where SOUL fails using a different AVI container, but he eventually fail in the same place.

  The strangest thing is that when I turn off the clips in first and dragged made I tried, it hangs on the same clip as if it has not been disabled! I also deleted the clips in the timeline and they always appear in the window of insight into the SOUL and it hangs on them and it fails!

  Here are my system specs:

  First Pro CC (updated)

  Win 7 64 bit (up to date)

  I7 970

  24 GB Ram

  NVIDIA 470GTX (updated driver)

  3 x 1.5 TB internal

  4 TB internal

  3 TB internal

  12 to RAID 5 via USB 3.0

  USB 2.0 and 3.0 readers

  Audio device FireWire (M-AUDIO FireWire1814)... even if I'm not using it for reading. It is connected.

  Images East of C100 H.264. MTS, JPEG. MOV of AE, JPG still images, the simple titles made in Premiere Pro, color mattes, and. WAV audio clips

  All stocks transitions and video effects.

  Thanks for your help.

  Mark Mapes

  Adobe Media Encoder (AME)

  I tried a reinstall of PP and SOUL, move all the items of assets to another machine and encoding, activation and deactivation "Import sees natively" in the SOUL, the activation and deactivation of mercury in PP and SOUL, and I got the same result. SOUL fails encoding with an error "film compilation error. Same result when I tried to export from PP.

  The only thing that has worked has been made all the clips I created EI using a different codec (was MOV JPEG and I have a new Lagarith AVI rendering). It seemed to work. When it would fail in SOUL he would hang a frame for several minutes before giving me the sound of sheep. Clips from MOV JPEG original of the PP has played very well in the sequences and multimedia players. No drama, no glitches.

  Don't know why wan't SOUL update sequences of PP. The fix for this was the launch of SOUL with Shift key to clear preferences. Also I made sure I saved pp until I dragged more than SOUL for encoding.

  I hope this will help someone else along their journey. Thanks for the research!

• FDQM HFM export error

  Hi guys,.
  
  After the initialization of a few places in FDQM and having faced export errors which I have been able to resolve, I came by it and after that drilled down I don't understand what exactly is the question:
  
  the 400100 is one tale of HFM, as others. I see data in detail, strange. Someone at - it suggestions? Thanks in advance!
  
  ? Load data started: 21/01/2011 19:32:23.
  Line: 83, error: the dimension member account is calculated.
  REAL; 2010; NOV; YTD; 940; 400100; [ICP NO]; [NONE]; [NONE]; [NONE]; [NO];-551907.13251
  -400100
  
  Line: 84, error: the dimension member account is calculated.
  REAL; 2010; NOV; YTD; 940; 4003000; [ICP NO]; [NONE]; [NONE]; [NONE]; [NONE]; 1358.34111
  -4003000
  
  Line: 85, error: the dimension member account is calculated.
  REAL; 2010; NOV; YTD; 940; 4003050; [ICP NO]; [NONE]; [NONE]; [NONE]; [NONE]; 2.04967
  -4003050
  
  Line: 86, error: the dimension member account is calculated.
  REAL; 2010; NOV; YTD; 940; 4004350; [ICP NO]; [NONE]; [NONE]; [NONE]; [NO];-12263.10861
  -4004350
  
  Line: 87 error: the dimension member account is calculated.
  REAL; 2010; NOV; YTD; 940; 4004450; [ICP NO]; [NONE]; [NONE]; [NONE]; [NONE]; 292.198
  -4004450
  
  Line: 89, error: the dimension member account is calculated.
  REAL; 2010; NOV; YTD; 940; 402100; [ICP NO]; [NONE]; [NONE]; [NONE]; [NO];-20422.03584
  -402100
  
  Line: 91, error: the account dimension member is not the base level.
  REAL; 2010; NOV; YTD; 940; 402400; [ICP NO]; [NONE]; [NONE]; [NONE]; [NONE]; 9018.19944
  -402400
  
  Published by: JDeM on January 23, 2011 03:33

  Hello

  If you enable the report of Validation Intersection, you have some reported lines that are all black?
  If Yes, then it may be because of a rule of no entry in HFM.

  Best regards
  Markus

• Satellite A300D-135 - BIOS - System Configuration data read error

  After starting a Satellite A300D-135 laptop computer, the following error message appears:

  
  3070M extended RAM passed
  512 KB of L2 Cache
  System BIOS with a shadow
  Video BIOS with a shadow
  ATAPI CD-ROM: TSSTcorp CDDVDW TS-L632H
  Fixed disk 0: TOSHIBA MK2546GSX
  Initialized the mouse
  ERROR
  System Configuration data read error

  Press to resume, installation

  After pressing F1 the machine starts Windows, very well, but the error message is quite irritating, while it comes with a loud BEEP

  I tried the following things so far (in that particular order):
  -Load BIOS default
  -Flashed the BIOS with the latest version of the BIOS (2.80) for this type of model
  -Reinstalled windows with HARD drive format

  All the these did not work.

  I saw the same message appearing on several places on the internet (on different laptops with a Phoenix BIOS in common), but so far I have not been able to find a working solution.

  It might me a hardware problem, but all devices (vga, soiund, lan, wifi, usb, hdd) seem to work perfectly under Windows, so this does not seem the question). Another solution that is mentioned in some forums, replace the battery. But because the phone keeps time correctly I don't think it's the case either.

  Any ideas?

  Kind regards
  GJ

  Hello

  The POST (power on self-test) BIOS checks and detects errors on the motherboard.
  I think it has something to do with the hardware on the motherboard problem.
  I doubt that you can solve this if update of the BIOS and the BIOS default settings didn't change that.

  What to say; I think that the technician of the ASP should run tests to check what's wrong or what cause this I think it is question of s mobo.

• Satellte M30: BSOD - KERNEL DATA INPAGE ERROR atapi.sys

  Hello

  I really hope, really, that someone can help me. I'm no computer Wizard, so if you can help please give me simple instructions. My problem is that often my satellite M30 freezes and blue page happens to give me a warning.

  Top of the page is KERNEL-DATA-INPAGE-ERROR, then goes on to say disable Options memory BIOS such as cache or shading, atapi.sys says below.

  So can someone please help.

  Thank you

  Hello

  Because you are not a computer expert ;) I'll try to write as simply.
  It looks more like a hardware problem as a problem of software!

  But to be 100% sure, you should recover the laptop with the Toshiba Recovery CD supplied.
  This CD will be programmed the laptop back to the factory setting and usually the laptop should work properly after the recovery of the new!

  If you the BSOD will appear again the chances are high that memory, HARD drives and the motherboard is malfunctioning.

  But because you are a beginner, I would not recommend trying to solve this problem yourself.
  In this case, you must contact the ASP in your country!

  Good luck

• Equium A300D - 13 X - Configration system data read error

  Hello

  I have a problem with my Equium A300D - 13 X laptop, everytime I turn on my laptop it starts and loads the initial startup screen as usual, Toshiba once asked that loud "BEEP" comes from my laptop, and lists the following information:

  Phoenix TrustredCore (tm) NB
  Copyright 1985-2006 Phoenix Technologies Ltd.
  All rights reserved

  Herring of the ITA (DDR2 + T/RS690M/SB600)
  CPU speed = 2000 MHz

  639K system spent RAM
  1918M extended RAM passed
  1024 KB of L2 Cache
  Occult system BIOS
  Video BIOS with a shadow
  ATAPI CD-ROM: MAST * ADVD-RAM UJ-850 S
  Fixed disk 0: WDC W2500BEVT-00SCSTO
  Fixed disk 1: Hitachi HTS542520K9SA00
  Initialized the mouse
  ERROR
  System Configuration data read error

  Press to resume, installation

  I replaced the hard drive and flashed the BIOS settings as advised by Toshiba Helpline but the problem persists.

  Help, please! because the "BEEP" is now getting on my nerves!

  See you soon

  Hi andrew_net82,

  It seems that the BIOS has detected an error with a certain part of material...

  Before doing something I recommend you load the default settings in the BIOS. If you are in the BIOS Setup, press the F9 key.

  If it doesn t work you need for professional assistance from an authorized service I think. Guys need to check which part of the material is defective and must be replaced.
  List of the ASP, you can find on the official website of Toshiba.

• Data length error! Helps the release of Keyence micrometer

  I am connected to a micrometer of LS7600 Keyence, and I am able to send commands to the micrometer, as well as receive structred outputes.  For example:

  Command: M0, 1

  Return: ER, M0, 20

  Soul ER error, M0 is my exit command, and 20 means DATA LENGTH ERROR.

  I use a very basic VISA program that connects to the Keyence via my Serial Port.

  So when the micrometer Keyence attempts to send the data I requested, it apparently can't do because it encounters a data length error.  I know it's a problem with my labview software because I can output these values successfully using a Hyperterminal connection.

  The data SHOULD go back which looks like this: M0 + 25.2531

  It's just 12 bits?  Can anyone think why labview does not accept this string?

  Check the display format of the indicator, that you look at the number.  It by default 6 significant digits, is exactly what you say.

  The integer is in the orange wire, just your indicator is not set to show them all to you.

• Blue screen and CORE-DATA-INPAGE-ERROR Message

  The blue screen and the CORE-DATA-INPAGE-ERROR Message appeared during extract some files, 2 consecuentlly. It has happened too, but not that often and during other processes. What should I do? The OS is Vista Home Premium.

  Indeed, I am here!

  Thank you for fixing links.

  The attached file of the DMP is to bug checking KMODE_EXCEPTION_NOT_HANDLED (1e) .

  This indicates that a kernel-mode program generated an exception which did not catch the error handler.

  8th error checking, {c0000005, 9eaa4efc, e551bae0, 0}

  0: kd > 9eaa4efc ln
  (9eaa4eb2) win32k! PFEOBJ::vFreepfdg + 0x4a |  (9eaa4f65) win32k! MultiUserGreTrackRemoveEngResource

  The exception is produced in win32k! PFEOBJ::vFreepfdg + 0x4a.

  0: kd > k
  ChildEBP RetAddr
  e551b6a0 84071908 nt! KeBugCheckEx + 0x1e
  e551ba70 8409584 has nt! KiDispatchException + 0x1a9
  e551bad8 840957fe nt! CommonDispatchException + 0x4a
  e551bafc 8401e70c nt! KiExceptionExit + 0 x 186
  e551bb64 9eb38a95 hal! KfLowerIrql + 0 x 64
  e551bb84 9eafac21 win32k! RFONTOBJ::vDeleteRFONT + 0 x 130
  e551bbbc 9eafada2 win32k! vRestartKillRFONTList + 0x7b
  e551bbf0 9eaafcd7 win32k! PFTOBJ::bUnloadWorkhorse + 0 x 115
  e551bc1c 9eaaf8d9 win32k! vCleanupPrivateFonts + 0x4d
  e551bc34 9eaac06e win32k! NtGdiCloseProcess + 0x16c
  e551bc54 9eaabbad win32k! GdiProcessCallout + 0 x 145
  e551bc70 84262 has 48 win32k! W32pProcessCallout + 0x5d
  e551bcdc 8423f47f nt! PspExitThread + 0x4a0
  e551bcf4 840fde8e nt! PsExitSpecialApc + 0 x 22
  e551bd4c 84094d 42 nt! KiDeliverApc + 0x1dc
  e551bd4c 77a95d14 nt! KiServiceExit + 0 x 56
  WARNING: Frame IP not in any known module. Sequence of images may be wrong.
  04adf6dc 0x77a95d14 00000000

  Associated police crashes, likely a buffer overrun.

  ---------------------------------------------

  1. remove the font cache and then restart > C:\Windows\System32\FNTCACHE. DAT

  * I recommend that you create a system restore point before that just to be sure: Vista - START | type rstrui - create a restore point.

  2 you have avast! + Security installed Aladdin, is at the origin of the conflict.

  Remove and replace avast! and Aladdin with temporary Microsoft Security Essentials for troubleshooting purposes:

  avast! removal - http://www.avast.com/uninstall-utility

  MSE - http://Windows.Microsoft.com/en-us/Windows/Security-Essentials-download 

  3 uninstall Smart Defrag as soon as possible.

  4 uninstall RealNetworks as soon as POSSIBLE, the drivers are too old - 2003.

  Kind regards

  Patrick

• Computer laptop Gateway does not load windows Vista, reads configuration data read error: System.

  OK a friend knows me to fix his laptop. Apparently what she was experiencing major problems, so he erased the disc and tried to reinstall Win Vista from disk. Will not work. I can get to where you can choose a partition to install the operating system to, and it says: Windows cannot find a system volume that meets its criteria for installation. My friend says he has just tried, form disassemble the computer an audit of all the parties to try ALL the different options during installation, as well as the options for the BIOS. Any ideas people? Here are the approximate specifications, because the owner has not been able to get the computer working for awhile:
  4 GHz, 4 GB RAM computer Gateway laptop, 2006, Phoenix TrustedCore, and a string of other interesting info that appears on the first screen of the error:

  9D.03 BIOS version

  632K RAM passed system
  3966M extended RAM passed
  1024 KB of L2 Cache
  System BIOS with a shadow
  Video BIOS with a shadow
  ATAPI CD-ROM: Optiarc DVD RW AD-7563 has
  Fixed disk 0: WDC WD2500BEVS-26VATO
  Initialized the mouse
  Updated System Configuration data
  ERROR
  System Configuration data read error.

  I'm not very tech savy and I'm not the owner of the PC, so I don't know all about it so go easy on me :).

  If your friend tried to reinstall Windows by using the defined gateway recovery disc (and this is the best way) and this recovery fails, the laptop has hardware problems. Disassemble laptops is a fickle business at best and while it sounds like the hardware problems started before your friend did this, it may have put the nails in the coffin of the laptop to take apart.

  At this point, you can try troubleshooting hardware or your friend can take the laptop to a competent professional (not a type of BigComputerStore/GeekSquad of the place). However, if the laptop has had hard use, your friend must remember that a cell of 4 years with major hardware problems probably won't be cost effective to repair.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot MS - MVP - Elephant Boy computers - don't panic!

• Kernel data Inpage Error... Memory dump... Please help me

  Hi my name is shoaib.

  I am facing a problem of blue screen approximately every 20-40 minutes. I run the memory test and you indicates no error. I check the RAM via the command "mdsched.exe" and she also don't say no found error. But when the blue screen appears it is said on the top of the page "kernel data Inpage Error".

  Please tell me what to do?

  Here is my file link "msinfo32".

  http://1drv.Ms/1Lu9SpH

  I have not found any "directory Minidump" in C:/windows. Please suggest me what to do. I really need your help. Thank you

  If you stopped crashing run a trace of windows performance when you encounter the problem

  In order to diagnose your problem, we need run Windows performance toolkit, the instructions that are in this wiki

  If you have any questions do not hesitate to ask
  
  
  Please run the trace when you encounter the problem

• Dat2.data version error

  I get the dat2.data Version error when I try to print, or even to open Microsoft Word 2007.  It started when I loaded the new epson drivers on my computer.  I tried to uninstall the epson SW but it won't let me, it times out.

  Hi Tom Callaghan,.

  Welcome to the Microsoft Answers community.

  Do you have which version of the driver installed?

  You can install the old driver version and check.

  I suggest to start your computer in clean boot mode, and then uninstall the printer driver and restart your computer. Reinstall the printer drivers.
   
  Method 1: Steps to uninstall and reinstall the printer driver.
  1. click on the Start button and select Control Panel.
  2. click on programs.
  3. click on programs and features.
  4. now uninstall the printer drivers.
  5 restart your computer. This will automatically install the appropriate drivers for it.

  You can also download the driver for it from the manufacturer's Web site.
  http://www.Epson.com/cgi-bin/store/support/SupportIndex.jsp?OID=-10222&infoType=overview
   
  Method 2: Steps to start in clean boot mode:

  1. click on start, type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
  2. in the general tab, click Selective startup.
  3. under Selective startup, clear the check box load startup items.
  4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
  5. click on OK.
  6. When you are prompted, click on restart.

  http://support.microsoft.com/kb/331796 . In addition, see the section on how to restore your computer to a Normal startup mode.
  If the methods above does not solve your problem, and then run system restore.

  Method 3: System Restore will take your computer state permeable when it did not face such a problem, this can be done by selecting the correct restore point.

  To restore the operating system to an earlier point in time, follow these steps:

  1. Click Start, type system restore in the search box, and then click System Restore in the list programs.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  2. in the System Restore dialog box, click on choose a different restore point and then click Next.
  3. in the list of restore points, click a restore point created before you started having the problem, and then click Next.
  4. click on finish.

  For more information, visit the links below:
  http://support.Microsoft.com/kb/936212/
  http://support.Microsoft.com/kb/826862

  Hope this information is useful.
  Let me know if it worked.
   
  Thank you, and in what concerns:
  Umesh P - Microsoft Support