Dial-up access hangs after the authenticated message

Similar Questions

• Outlook express hangs after the connection with the mail server

  OE6 hangs after the connection with the mail server?

  Make sure that the other machine is not check that the server so often a machine is not problems because it cannot be verified.

  Try to delete the account, compact the folders and close OE and reopen it and add the account back again.  Also make sure that the antivirus software is not interfere (see www.oehelp.com/OETips.aspx#3).

  You can also telnet to the server directly from this computer to see if it works (see http://techhelp.santovec.us/pop3telnet.htm).

  Sometimes it gets stuck in a message on the server and it can not get downloaded by OE, so it may be necessary to remove the message from the server, but if the other machine got, maybe it's not the question.

  Steve

• VPN client hangs after password authentication

  Hello

  When a remote client tries to establish a VPN session with our (6.3 ongoing) Pix Firewall, it crashes right after the prompt of password with this message (see attachment). When I try the same all works very well. I've included bits of code, I think that relate to their installation.

  name 128.51.0.3 ATG-STELPLAN-Svr

  name 128.60.4.4 ATG-Irish-EMS-Svr

  name 194.201.29.0 LAN-Metalogic

  name 192.168.2.0 LAN-Metalogic2

  name 128.31.1.78 MultiMetals-new-Svr

  name 10.10.253.253 Metalogic_Support_Host

  acl_mdc_inside_nat0 list of allowed access host ip host MultiMetals-new-Svr Metalogic_Support_Host

  acl_mdc_inside_nat0 list of allowed access host ip host EMS Metalogic_Support_Host

  acl_mdc_inside_nat0 list of allowed access host ip host ATG-EMS1 Metalogic_Support_Host

  acl_mdc_inside_nat0 list of allowed access host ip host ATG-STELPLAN-Svr Metalogic_Support_Host

  acl_mdc_inside_nat0 list of allowed access host ip host ATG-Irish-EMS-Svr Metalogic_Support_Host

  acl_mdc_Metalogic-remote_split_tunnel permitted object-group Murray_Subnets ip access-list all

  Metalogic_Pool Metalogic_Support_Host local pool IP 255.255.255.255 mask

  NAT (inside) 0-list of access acl_mdc_inside_nat0

  vpngroup address pool Metalogic_Pool Metalogic_Support

  vpngroup Metalogic_Support by default-field carnegie - it.com

  vpngroup split acl_mdc_Metalogic-remote_split_tunnel tunnel Metalogic_Support

  vpngroup idle 1800 Metalogic_Support-time

  vpngroup password Metalogic_Support *.

  Help, please.

  Thank you

  Rex

  Well, if they have a Linux IPSEC firewall will pass through. A similar problem and the issue of the Linux not passed IPSEC traffic. I suggested to the other party to try the laptop worked outside area and power.

  Therefore, do not worry coz your configuration is correct.

  Let me know if you need help,

  Kind regards

• Satellite M50 226 hangs after the victory of logon Wlan is turned on

  Hello everyone,

  I had a problem with my satellite m50-226.
  It happens quite often that when I boot up my laptop a card WiFi is turned on, the computer hangs after windows journal.
  When I type my user password nothing happens and a few seconds later, the background appears but nothing else.
  When I restart the laptop the same problem occurs. only when I turn off the wlan card, I can start the computer successfully.

  Maybe anyone can help me?

  thanx.

  welcome them
  Alex

  Hello Alex

  I am very interested about your problem and it is interested to know if this problem persists if the unit wakes from sleep or hibernation mode.
  Can you please verify this?

• hot to turn off Java after the startup message

  Hello world

  I know it's a bit old, but I couldn't find an answer to it, or maybe I searched the wrong topic. After the reboot, I still get this warning window saying "to use the"java"command line tool, you need to install a JDK.
  I ElCapitan and recommended Java installed since Mavericks version, but the message never goes away. The used warning window is displayed only after restart, but now he appears randomly during normal use of the laptop.

  Please help me to get rid of

  You have software that requires the Java command line tool? It is only in the JDK you will find Oracle's Web site.

  Check your/Library/LauchAgents and /LibraryLaunchDaemons for startup like facebook or similar items. Also, check your user settings (users & groups) under your Log - In for Autostart-software items after the connection.

• X 1 carbon 2014 windows 7 hangs after the main power connection

  Nice day

  After the Polish Lenovo call center refuses to help me ask you to help. For about a week now, my X 1 carbon 2014 hangs after connection to the power supply. It's so irritating. I think, I only installed the updates regular windows 7 and the update of the BIOS via the lenovo update tool.

  The Polish Lenovo Support Center came with the excellent range of system solution. I really hope that you would be able to help more effectively at the same time.

  Thank you!

  Pawel

  
  

• HP Pavilion DV6-2106EA hangs after the insertion of son wired CAT5 (internet)

  HP Pavilion DV6-2106EA hangs after when inserting the cable wires CAT5 for wifi internet works fine

  or wireless works fine. Need help

  Hello

  Unplug your ethernet category 5 cable.

  Download the LAN driver from the link below and save it to your desktop.

  FTP://ftp.HP.com/pub/SoftPaq/sp46501-47000/sp46504.exe

  Then, in the Menu start, open the all programs, open accessories, right-click on command prompt and select "run as Administrator".  In at the prompt, type the following command and press ENTER.
   
  sfc/scannow               (Note that there is a space between sfc and /)
   
  Let the entire process, then the output type and press ENTER.

  Now, right click on the installer you downloaded and select "Run as Administrator" to launch the installation.  When finished, restart the computer and try to connect the cable again.

  Kind regards

  DP - K

• How to open documents in works 9 after the error message

  After the execution of Advanced System Care 5, I am unable to open my Works documents.  I see that they are still in my computer, but I get an error message that says: they have been renamed, deleted or moved and he said to try reinstalling works.  I am also unable to connect to Windows Live Messenger.

  Help, please.

  Thank you.

  After running advanced system care 5

  
  
  See if you can undo the damage of this product of the powder of snake oil. I've seen many problems with this product on the forums, especially since windows file system causing to show as non-genuine.
  I suggest to uninstall this product and not the registry cleaners or speed up my pc products. They do no good and as you now know, can cause damage.
  EDIT:
  You could try their forums. The two problems that you have mentioned:
  http://forums.iobit.com/forumdisplay.php?f=59

• WRT110 hangs after the addition of a new wireless client

  Hi all:

  I have had this problem since I bought the router. After first seen he question, I checked the firmware version and find that I 1.0.04)is. Information on the next release say nothing on fixing this, so I did not bother to update.

  Here's a detailed description:

  I have a home network with approximately 8-10 computers. Eight computers are wired. Two are laptops. I travel every week and whenever I come home and start my laptop, the router needs to be reset. If I did not, none of the computers, including my laptop can connect to the network. In addition, I am unable to pull up to the router configuration page. After the reset of the router (unplug) everything works fine. even the wireless on my laptop.

  I just got used it although it was frustrating for my children. Now I have another laptop for my wife and she connects more often, and when I'm not home. I don't want to have to deal with to reset the router if I have to.

  I've not seen anything like this in the forums, the firmware doesn't seem to be an option, so if anyone has a solution for this, I would appreciate it.

  Thanks in advance!

  You need to reset hard your router to the factory settings and then try to configure the re-...

  To reset the router press and hold the reset button for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...
  Also, make sure that your computer is configured to obtain an IP automatically, disable any firewall, the security software on the computer before you try to access the configuration page...

  I understand you want to upgrade the firmware of your router, but you should give it a try if the above does not solve your problem...

• Local access only after the Network Systems Security 2009 malware removed

  I'll try to put all the details that I can here, but my laptop that has the problem cannot connect to the Internet so I won't be able to copy paste n info. Last week, I was struck with the 2009 malware security systems. It was a pain to remove because it stopped all the work programmes and I could not install malware removal software. Finally beat him by renaming the main program folder 2009 for the security of the systems. That he has stopped working when I restarted the laptop and then I was able to install the malware removal software and took remoped.

  Here is the problem. Now that he is gone my network connections wireless and wired no longer work. I get local access only on an unidentified network. I have Windows vista Home premium and use internet with a modem model Cableone cable Motorola Surfboard SB5101.

  Then I called a cable tech support first and they could not help and after all the service works very well on my desktop the same modem and connection. So I called Motorola tech support and they had me do a lot of things for hours (including reinstalling the drivers for the modem) on the phone without effect. Finally, they suggested that I have re-download all ACER Aspirion z9410z drivers and reinstall them. So I did it. Copied to a flash of my desktop drive and reinstalled them. No luck.

  The respectable and sharing Centre, explains that the modem works correctly when you look at the status. But the auto for windows diagnostic tool says to check the IP settings automatically and reset the network card. The two fail to trouble when ran. Here are all the parameters of the network connection.

  Physical address: 00-1A - 66 - AA - 64cB
  Active Yes DHCP
  Autoconfiguration IPV4 address 169.254.195.250
  IPv4 mask subnet 255.255.0.0
  Net Bios on active TCP/IP Yes
  Link-local IPV6 address fe80::1878:12 d 5: a566:c3fa % 36
  Servers of DNS IPv6 fec0:0:0:ffff:1 1%
  FEC0:0:0:FFFF:2 1%
  FEC0:0:0:FFFF:3 1%
                                                  
  IPv4 and 6 are defined automatically detect the IP address and the DNS.

  Hope that gives enough information. There no mater if I use eithernet and USB to connect or wireless. I have the same problems.

  Another thing that can be part of the problem.

  It started after removing the systems security 2009 malware as well.

  When loggin, turned off the laptop, a blue error screen appears. Here are the details generated for it. I'm working on the research of which the question is to be set by the online search.

  Event name BlueScreen
  OS version 6.0.6000.2.0.0.768.3
  local ID 1033
  BCCODE one
  BCP1 00000016
  BCP2 0000001 B
  BCP3 00000000
  BCP4 82028768
  OS version 6_0_6000
  Service Pack 0_0
  product 768_1

  I hope I will get this fix as well.

  Any help will be greatly apprieciated. If more information is required only, let me know and I'll get it.

  Thank you all.
  Jason

  Hello Oxilas,

  I suggest that you use a friend/co-worker Vista DVD and do a repair installation.

  Repair facility:

  You can reinstall your copy of Vista while keeping your files, settings and programs by performing a repair install or an upgrade on the spot with the following steps: (Note: this still does not resolve all problems, especially if the corruption was caused by a 3rd party program or service, you may need to do a clean install) (if this is not successful.)

  <><><><><><><><><><><><>

  Please make sure that you back up all the important data before you continue. Please visit: methods for your backup files.

  Always make sure that you have the means to reinstall your programs, or by an installation disc or access to the installation files.

  <><><><><><><><><><><><>

  1. Insert the Windows installation disc in your computer's DVD or CD drive. You must start Windows installation while running your existing version of Windows.

  2. on the Install Windows page, click install now.

  3. on the get updates for installation page, we recommend getting the latest updates to help ensure a successful installation and to help protect your computer against security threats. You will need an Internet connection to get the installation updates.

  4. on the Type your product key for activation , we strongly recommend that you type your 25-character product key in order to avoid problems during activation.

  5. on the page Please read the terms of the license , if you accept the license terms, click I accept the terms of the license.

  6. to the which type of installation you want? page, click upgrade to begin the upgrade. You can see a compatibility report.

  7 follow the instructions.

  Note: If your installation disc doesn't include SP1, and you are updated, then you must uninstall it before proceeding with an update install. Start-> Control Panel-> programs-> see installed updates, then select Service Pack for Microsoft Windows and click on Uninstall.

  Note: Tit the following settings is reset by default:

  Its computer system

  Device drivers

  Visual effects

  Windows Mail

  Windows services

  If you notice missing files after the upgrade, look in the following folders:

  C:\Windows.old

  C:\$INPLACE.~TR

  C:\$WINDOWS.~Q

  These files can be eliminated with disk cleanup as "records destroyed by upgrade to Windows".

  Delete files using disk cleanup

  Thank you for using answers Forum. Please let us know how it works.

  Joseph
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Java plugin for Oracle hangs after the last update

  As part of the requirement of the Oracle, we run JRE 1.7.60
  To update firefox this morning and now the plugin is constantly crashing.

  Hello

  Thanks for your reply, but I doubt that flash player is related to do with Java.

  And the Java applet crashing in my browser, I guess, should not be linked to my graphics driver, especially since the only update that took place was an update of firefox.

  In any case, Firefox for some reason any launches 2 additional tabs when executing the Java Applet (IE does not work). In the past, I'm used to close the first tab, since it contains nothing except an Oracle logo.
  However, it seems that after the last update of firefox, if this tab is closed, it cause Java to crash.

  Therefore, do not close the additional tabs by the Java Applet. However, this has never happened before, do not know what has changed in the latest version of Firefox to make it happen now?

  Thank you

• Front Panel hangs after the beginning of the routine

  Hello

  I am writing an application that looks a bit like that fixed. The idea is to have a Setup mode after the beginning of the program, where you can enter all the data to specify a test routine. In the first loop representing the configuration mode, I have an event structure that is pretty huge, in fact, because it represents a contextual help for my program, I added. After clicking on the Start button (which is possible only when some tabs from the tab control are selected), I turn off and the Start button gray. After that puts it on, there are several automatic modes and a manual control which are selected depending on the active tab.

  In this mode, the front suddenly freezes i.e. no control will react to my entry.

  I programmed this sample program to get because of the problem. It seems that there is a problem when using local variables and the switch until released action. The problem was solved when I selected the switch when you press mode.

  I applied the same changes in VI I develop, but the problem still remains.

  Someone at - he had an idea, why?

  
  

• After the error message with computer-media center Scheduler etc has stopped working

  Original title: 8 boxes

  On separate cards on top of each other - they look like maps of correspondence-is this news centre Media State media stopped services aggregator, the drawer module igfx has

  order, hkcmd module has ceased, HD audio Panel has stopped working, Task Scheduler engine stopped working, a persistence module

  stopped working, sink to receive asynchronous callbacks for WMI client applications has stopped working.  They appear after the computer was during one

  While using the Internet, Facebook, please help.

  Hi sue them.

  ·         Did you do changes on the computer before the show?

  ·         Exactly when you receive the following errors?

  ·         What web browser do you use?

  Follow the suggestions below for a possible solution:

  Method 1: I suggest you to start in safe mode with network and check if the similar problem occurs in safe mode.

  Startup options (including safe mode)

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

   

  Method 2: Try the SFC (System File Checker) scan on the computer.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  I hope this helps.

• Windows 8 metro apps hang after the screen saver

  When in the start menu screen of windows 8 after logon after the system remains idle for more than 60 minutes of any style windows app 8 does not open

  ex IE, people, mail, weather, etc.

  'Goto Office tiles' and all the other things like charms work but the applications themselves (all) just stay stuck on the screen to start the application

  Help, please!

  Hello

  Did you make any changes before the show?

  You can run the resolution of the problems of the article below and check.

  Method 1: What to do if you have problems with a soft

  http://Windows.Microsoft.com/en-us/Windows-8/what-troubleshoot-problems-app

  Method 2: Perform the resolution of the problems of system maintenance. Follow these steps:

  (a) press Windows + W key on the keyboard

  (b) resolution of the problems of type and then click settings under the search field

  (c) in the settings click on find and fix problems

  (d) click on system and security

  (e) maintenance of the system click on follow the prompts from there.

  Let us know the status of the issue. I will be happy to provide you with the additional options that you can use to get the problem resolved.

• As the location of the cursor in the text after the notification message field

  Hello
  
  I like that the cursor is in the field of single text called P22_Codigo_barras, to close the notification message that the process has been saved successfully
  
  
  
  Thank you for your attention
  
  REYNEL Martinez Salazar

  Hello

  In your page template, you can add javascript code that defined the focus on this element? You need to go to the notification of the page template (shared components - templates) section you can also do it with jquery.

  Hope that helps.

  Kind regards
  Dimitri
  ----------------------------------
  http://dgielis.blogspot.com/
  http://www.apex-evangelists.com/