Different networks on different Interfaces

Similar Questions

• "Move" failover to different / interface port

  Sorry if this is in the wrong place, we had if rarely to issues which were not covered otherwise I frequent this area.

  How is it difficult to change the interface used for active failover / standby? This is a pair of work, already configured with standby, but I need to move the cable crossed and tell them to use a different interface.
  Pair of ASA 5510, already put in place and work with failover, which was originally set on Ethernet port 0/3 by senior network administrator. It seems that its use of interfaces or ports he used things straight out of the examples on the web, including the interfaces used.
  The admin network senior retired last spring and left me "supported", gee, thanks.
  I need to make some changes and Ethernet port need for an important new project.
  The management interface 0/0 is unused and shut down. We manage by inside the interface from a specific inside subnet so do not need the interface dedicated management.
  I want to spend the shift IN management TO Ethernet 0/3 0/0

  * This is the current configuration:

  Output of the command: "sh run failover.

  failover
  primary failover lan unit
  failover failover lan interface Ethernet0/3
  failover failover Ethernet0/3 link
  failover interface ip failover 169.254.255.1 255.255.255.252 ensures 169.254.255.2

  * And it's the current 0/3 interface and management configuration:

  interface Ethernet0/3
  STATE/LAN failover Interface Description
  !
  interface Management0/0
  Speed 100
  full duplex
  Shutdown
  nameif management
  security-level 0
  no ip address
  OSPF cost 10

  I know that it can work on the management interface 0/0 because I see a lot of 'how to configure' as if the SAA is brand-new and several examples there indeed be setup on the management.

  I'm looking to find out how to take a pair of ASA is currently configured and has a functional work and all failover configuration simply "tilting move" to a different hole, or change the interfaces used for the 'heartbeat' somehow.

  I guess that's not difficult - but I also assume that there is a specific sequence of events that must occur in order to prevent the pair to enter the failover and switching of the main roles...
  For example - would have turned off or turn off the power switch and if so, how and on what ASA (frankly, I don't know how to access education secondary or standby if it needs to be done, suspended or on the rescue unit, because I never did that 'deep' a before config)
  CLI is very well - I'd be too comfortable in ASDM or cli.

  I really hope this makes sense - I have more than one convenience store and fixer than a designer or network engineer...
  And thank you very much - get this moved will release the interface I need and can really make a big bump in my list of project while the project manager is on vacation this week! I'd love to have done this and before his return.

  Oh, in case it is important as I said, it's running license and version shown here:

  Cisco Adaptive Security Appliance Software Version 4,0000 1
  Version 6.4 Device Manager (7)

  Updated Friday, June 14, 12 and 11:20 by manufacturers
  System image file is "disk0: / asa844-1 - k8.bin.
  The configuration file to the startup was "startup-config '.

  VRDSMFW1 141 days 4 hours
  failover cluster upwards of 141 days 4 hours

  Material: ASA5510, 1024 MB RAM, Pentium 4 Celeron 1600 MHz processor
  Internal ATA Compact Flash, 256 MB
  BIOS Flash M50FW080 @ 0xfff00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
  Start firmware: CN1000-MC-BOOT - 2.00
  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.06
  Number of Accelerators: 1

  0: Ext: Ethernet0/0: the address is 0024.972b.e020, irq 9
  1: Ext: Ethernet0/1: the address is 0024.972b.e021, irq 9
  2: Ext: Ethernet0/2: the address is 0024.972b.e022, irq 9
  3: Ext: Ethernet0/3: the address is 0024.972b.e023, irq 9
  4: Ext: Management0/0: the address is 0024.972b.e01f, irq 11
  5: Int: not used: irq 11
  6: Int: not used: irq 5

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited perpetual
  VLAN maximum: 100 perpetual
  Guests of the Interior: perpetual unlimited
  Failover: Active/active perpetual
  VPN - A: enabled perpetual
  VPN-3DES-AES: activated perpetual
  Security contexts: 2 perpetual
  GTP/GPRS: Disabled perpetual
  AnyConnect Premium peers: 2 perpetual
  AnyConnect Essentials: 250 perpetual
  Counterparts in other VPNS: 250 perpetual
  Total VPN counterparts: 250 perpetual
  Shared license: disabled perpetual
  AnyConnect for Mobile: disabled perpetual
  AnyConnect Cisco VPN phone: disabled perpetual
  Assessment of Advanced endpoint: disabled perpetual
  Proxy UC phone sessions: 2 perpetual
  Proxy total UC sessions: 2 perpetual
  Botnet traffic filter: disabled perpetual
  Intercompany Media Engine: Disabled perpetual

  This platform includes an ASA 5510 Security Plus license.

  Cluster failover with license features of this platform:
  The maximum physical Interfaces: unlimited perpetual
  VLAN maximum: 100 perpetual
  Guests of the Interior: perpetual unlimited
  Failover: Active/active perpetual
  VPN - A: enabled perpetual
  VPN-3DES-AES: activated perpetual
  Security contexts: 4 perpetual
  GTP/GPRS: Disabled perpetual
  AnyConnect Premium peer: 4 perpetual
  AnyConnect Essentials: 250 perpetual
  Counterparts in other VPNS: 250 perpetual
  Total VPN counterparts: 250 perpetual
  Shared license: disabled perpetual
  AnyConnect for Mobile: disabled perpetual
  AnyConnect Cisco VPN phone: disabled perpetual
  Assessment of Advanced endpoint: disabled perpetual
  Proxy UC phone sessions: 4 perpetual
  Proxy total UC sessions: 4 perpetual
  Botnet traffic filter: disabled perpetual
  Intercompany Media Engine: Disabled perpetual

  This platform includes an ASA 5510 Security Plus license.

  Serial number: ABC12345678
  Running permanent activation key: eieioandapartridgeinapeartree
  Registry configuration is 0x1
  Last modified by me to 15:03:07.132 CDT MON Sep 15 2014 configuration

  Disconnect an interface monitored on your rescue unit that will ensure that it does not take as active. Then cut the failover link and modify its failover parameters. (You will need to first remove the nameif for M0/0).

  Then, make the changes on the primary unit similar free game active. Reconnect the failover link, confirm the synchronization of the units and finally reconnect the interface of production on the rescue unit.

• Order of 100 Mbps with the same policy map on different interfaces of service-policy in routers

  We have several different interfaces in our routers. On that note, we have service-air to limit the bandwidth of 100 Mbps.

  If we use a sheet of class corresponding to a list of access as "permit ip any any".

  and map political with the class-map to the police up to 100 Mbit/s.

  If we apply this policy plan in the form of service-policy interface. All interfaces that use this service policy would share 100 Mbps or will they get 100 Mbps each?

  Thanks for any response.

  Concerning

  Henrik

  Hello

  As you apply the policy by interface, each interface will get 100 MB

  HTH

• ASA 5510 VPN multiple tunnels through different interfaces

  Is it possible to create VPN tunnels on more than one interface to an ASA (specifically 5510 with 8.4), or I'm doing the impossible?

  We have 2 public interfaces on our ASA connected to 2 different suppliers.

  We must work L2L tunnels of the SAA for remote offices through the interface that is our ISP 'primary' and also used as our default gateway for internet traffic.

  We are trying to install a remote office use our secondary connection for its tunnel (office of high traffic we would prefer separate away from the rest of our internet and VPN traffic).

  I can create the tunnel with the ACL appropriate for traffic tunnel, card crypto, etc., put in place a static route to force ASA to use the secondary interface for traffic destined for the public of the remote gateway IP address, and when I finished, traffic initiated by the remote site will cause the tunnel to negotiate and find - I can see the tunnel in Show crypto ikev1 his as L2L answering machine MM_ACTIVE , Show ipsec his with the right destination and correct traffic local or remote identities for interesting, but the ASA local never tries to send traffic through the tunnel.  If I use tracers of package, it never shows a VPN that is involved in the trafficking of the headquarters in the remote desktop, as if the SAA is not seeing this as for the corresponding VPN tunnel traffic.

  If I take the exact same access and crypo card statements list and change them to use the primary ISP connection (and, of course, change the remote desktop IP connects to), then the connection works as expected.

  What Miss me?

  Here is a sample of the VPN configuration: (PUBLIC_B is our second ISP link, 192.168.0.0/23 is MainOffice 192.168.3.0/24 is FieldOffice)

  permit access list range 192.168.0.0 PUBLIC_B_map 255.255.254.0 192.168.3.0 255.255.255.0

  NAT (Inside, PUBLIC_B) static source MainOffice MainOffice static FieldOffice FieldOffice

  card crypto PUBLIC_B_map 10 corresponds to the address PUBLIC_B_map

  card crypto PUBLIC_B_map 10 set counterpart x.x.x.x

  card crypto PUBLIC_B_map 10 set transform-set ESP-3DES-SHA ikev1

  PUBLIC_B_map PUBLIC_B crypto map interface

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  Route PUBLIC_B x.x.x.32 255.255.255.224 y.y.y.y 1

  If I take this same exact configuration and change it to use PUBLIC (our primary connection) instead of PUBLIC_B, remove the instruction PUBLIC_B route and change the desktop to point to the ip address of the PUBLIC, then everything works, so my access list and crypto map statements must be correct.

  What I don't understand is why the ASA Head Office does not seem to recognize interesting for the tunnel traffic when the tunnel is for the second ISP connection, but works when it is intended for the main ISP.  There is no problem of connectivity with the ISP Internet B - as mentioned previously, the tunnel will come and negotiate properly when traffic is started from the desktop, but the traffic of main office is never sent to the bottom of the tunnel - it's as if the ASA does not think that traffic of 192.168.0.x to 192.168.3.x should pass through the VPN.

  Any ideas?

  Hello

  I think your problem is that there is no route for the actual remote network behind the VPN L2L through ISP B connection

  You could try adding add the following configuration

  card crypto PUBLIC_B_map 10 the value reverse-road

  This should automatically add a static route for all remote networks that are configured in the ACL Crypto, through the interface/link-ISP B.

  If this does not work, you can try to manually add a static route to the ISP B link/interface for all remote networks VPN L2L in question, and then try again.

  The route to the remote VPN peer through the ISP B does not to my knowledge.

  I would like to know if it works for you.

  It may be useful

  -Jouni

• How to compare two different interfaces without creating different versions?

  I know that if we create two different versions of the same interface, so we can compare the two versions. But is it possible to compare two similar interfaces to each other, created in different folders?

  Hi 2782749,

  Not sure if it works with 11g, but possible in 12 c. In the main menu, click on ODI-> browser Version.

  Click on both interfaces, and then click Compare in the upper right corner of the browser Version.

  You can also export and a tool of comparison on the xml files to highlight the differences. The result will be about the same.

  Comparison tools:

  Windows: Compare plugin for Notepad ++

  UNIX: diff

  It will be useful.

  Kind regards

  JeromeFr

  [edited after realizing that a comparison even works with various items].

• To access the tables of an interface from a different interface intermediate I_ *.

  Is it possible to run this series of events?
  
  (1) load the data via the Interface 1 using a simple LKM and a revenge as "Incremental update of Oracle"
  (2) make sure the data store target on the "DELETE_TEMPORARY_OBJECTS" attribute of the IKM flow tab is set to 'false' (so it isn't serving the table when you are finished
  (3) load the data via the Interface 2, with a mapping that gets data leave 1 I_ UI staging table.
  
  Here's what we'd like to do in a few words:
  
  (1) for all records in a result set (let's call MODEL1 Range1 Interface), generates a sequence on a field value in the table of staging for I_MODEL1.
  (2) add MODEL1 to the list of sources for the mapping of Interface 2.
  (2) for all records to a different result together (call the MODEL2 of Interface 2) who meet a join clause and may be associated with a corresponding MODEL1 record search which generated the sequence value for the I_MODEL1 table and put it in this record for the I_MODEL2 table.
  
  Once both interfaces running, the two staging tables can be recessed. And, Yes, we have our own KM which twisted Oracle incremental update to push all the records through the agent, rather than simply generating the value of the sequence once for all of the defined result :-)
  
  Please advise,
  Michael

  I think it's possible if you remove the I$ 1 interface table. You just need to make sure that the second interface must not create one I$ table of the same name as the existing one (1st interface).

  Once the 1 interface will end the I reverse $ table and attach it to the corresponding source interface2. Then perform the necessary mappings. Now put them in order in a package.

• VPN via a different interface of the "outside" interface

  I have two ASA5510 each with two external interfaces, we're connecting to an ISP for the Internet and the other connects to an MPLS network. And I have the LAN on the interface of "inside".

  In my lab, I have each external interface connected to a separate router, and the router connects to an another ASA5510 who will be at the other end of the VPN.

  Enough of this scheme:

  LAN
  |
  |
  |
  |
  ASA--------------
  | defaultroute | specificroute
  |                       |
  |                       |
  |                       |
  Router router
  |                       |
  |                       |
  |                       |
  | defaultroute | specificroute
  ASA--------------
  |
  |
  |
  |
  LAN

  I bring a VPN on the interface either as long as I get the interface default route (0.0.0.0 0.0.0.0). So it seems that the configuration is correct. But given that I have only one default route, I can never raise the second VPN.

  I have a static route pointing to the peer through the correct interface and next hop for the second VPN IP and can ping and traceroute to the public address just fine so routing is correct, but...

  whenever I ping from LAN to LAN to make appear the second VPN log just shows it as an attempt to create a translation.

  It is as if it does not have it as "interesting traffic" but as a regular traffic to the Internet.

  Any thoughts on this?

  Thanks in advance.

  Hello

  If you need to configure the tunnel interface on the ASA (ISP or MPLS)... While you apply the card encryption on both interfaces.

  Then... routing will take care through which interface to negotiate the tunnel.

  Say that the remote site has this configuration:

  Public IP = 1.1.1.1

  Remote LAN = 10.1.1.0/24

  You should have this:

  Route ISP 1.1.1.1 255.255.255.255 NEXT_HOP 10

  Route MPLS 1.1.1.1 NEXT_HOP 20 255.255.255.255

  Route ISP 10.1.1.0 255.255.255.0 NEXT_HOP 10

  Route MPLS 10.1.1.0 255.255.255.0 NEXT_HOP 20

  In addition, configure IP SLA.

  Whenever the ISP interface goes down, the ASA will attempt to negotiate the tunnel via the MPLS interface (because is one that can be used to reach the other site).

  Federico.

• Installs have a different interface? 2015.0.0-> 2015.1.2?

  I'm the creative Cloud deployment on multiple computers and all bar one facilities - 2015.1.2

  A machine is on 2015.0.0 and does not update.

  Hello

  Please confirm the error code you get by updating. You can also try the steps on the link following error download, installation or update of Adobe Creative Cloud applications

• Physical networks VPN multiple interfaces of the ATA.

  Hello all and thanks in advance for any advice you can provide.

  I have a 5220 ASA set up with 3 networks. I have a off-grid, one inside the network and a network of "DSL". Everything works great, except that I'm trying to clean up the way we connect with VPN client.

  At the moment, if we are outside our network, we use the external IP address of the router (x.x.A.1). When we are on the LAN subnet, we are unable to VPN to the external IP address, so we are forced to use a completely separate identification information together and to connect to the IP address of the subnet LAN (x.x.B.1).

  Is it possible to configure the VPN so that we would be able to use the same credentials to connect to the interface either? I can use DNS selective so that requests are sent to the correct IP address... but as it is, it does not accept one set of credentials on each interface.

  Any help would be appreciated.

  Question:

  Have you tried to set up a separate crypto for the LAN interface card input.

  Lets say you have an entry like this crypto map...

  Crypto-map dynamic dynmap 65534 transform-set RIGHT

  cry map outside_map 65536-isakmp ipsec dynamic dynmap

  interface card cry out outside_map

  Can you try to create another entry card crypto under a different name for the LAN interface.

  Let me know.

  See you soon

  Gilbert

• Unable to connect to the network and wireless interface does not appear in ipconfig/all on Vista32

  My niece has a laptop of HP under vista32 who cannot access the network wirelessly or wired.  She is in College and needs the laptop on the network as soon as possible for his class work.  I tried to reload the driver wireless driver (Atheros AR5007 b/g) and reset the tcp/ip stack using the command netsh addressed in the microsoft article, but nothing works.

  I brought the laptop to work where we have an unsecured wireless lan (called comments) for visitors and the laptop can go out and find all points of access wireless including comments.  When I select the comments and try to connect it times out and tells me to watch driver and tcp/ip connections.

  Another clue may be that the wireless card does not appear when I type ' ipconfig/all', or the adapter wireless and wired adapters are not displayed:

  C:\Users\Admin>ipconfig/all

  Windows IP configuration

  Name of the host...: Hannah-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Bluetooth network connection Ethernet card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Device Bluetooth (personal area network)
  Physical address.... : 00-21-86-39-EE-22
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  C:\Users\Admin >

  I'd appreciate any help I can get.

  Thank you!

  In the case where somone has this same question, I wanted to post my final resolution of the problem. I backed up its data and restored the laptop to factory default using HP restore and now everything works fine.  Better I would say loading Zone Alarm on Vista was a bad thing for my niece to do.  Would have been nice to find a magical solution to avoid restoring but never found one.  Even after the alarm zone using their instructions by removing completely, there was apparently a problem with the registry who wouldn't let networks are working properly.  One thing I noticed after that the restoration was the HP Wireless Assistant poped up and told me about available networks, etc.  Assistant wireless didn't pop-up at all whne the cell was dismantled so maybe assistant was broken?  Well, I'm out...

• Need to programmatically change the network on an interface is

  Hi all

  A VSwitch our ESX servers is configured with multiple VLANs and I have a requirement for per program (command line) change the network Virtual Machine is too connected.

  Does anyone know how to do this?

  Thank you

  Darin

  You can manually edit the .vmx VM (s) configuration file and vimsh vmware-vim-cmd wrapper allows you to refresh the configuration VM (s):

  [root@himalaya root]# vmware-vim-cmd vmsvc/reload
  Insufficient arguments.
  Usage: reload vmid
  
  Reload the virtual machine state from afresh.
  

  Unfortunately the virtual machine must be powered off the coast, I think that to do this.

  If you need to do while the virtual machine is running, you'll want to take a look at the API of VI and watch in the ReconfigVM_Task() http://www.vmware.com/support/developer/vc-sdk/visdk25pubs/ReferenceGuide/vim.VirtualMachine.html#reconfigure

  It is also implemented in the VI Perl Toolkit Utilities in the form of script: http://www.vmware.com/support/developer/viperltoolkit/viperl15/doc/perl_toolkit_utilities_idx.html and you can watch the script called vmreconfig.pl http://www.vmware.com/support/developer/viperltoolkit/viperl15/doc/vmreconfig.html

  The VIPT must be running on one or the other Windows/Linux or on VMware VIMA/vMA, not on the Console of Service of ESX classic

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  repository scripts vGhetto

  http://Twitter.com/lamw

  If you find this information useful, please give points to "correct" or "useful".

• Adding routes when iface IP and GW a different network

  Hello.

  I ran into a question without an official answer. For example there is a network of the interface configuration:

  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  ... The IP address: 183.78.80.21
  ... Subnet mask: 255.255.255.255
  ... Default gateway. : 172.22.196.1.
  DHCP server...: 172.22.196.1.

  Now to do some routing for VPN, I add a route like this:

  route add {remote_ip} mask 255.255.255.255 172.22.196.1

  But this does not work, because no IP interface has this GW in the same network: the route addition failed: the index is wrong or the gateway are are not on the same network as the interface. See the Table for the IP addresses of the machine.

  If I specify interface

  route add {remote_ip} mask 255.255.255.255 172.22.196.1 if 2

  the error is the same (interface index 2 is that with the ip and gw).

  How to add this route? How to specify only the interface without GW? Remove GW command:

  route add mask 255.255.255.255 {remote_ip} if 2

  Displays the text of its use.

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

  Hope this information is useful.

• Can I have different AP with SSID groups using a single controller?

  I am designing a wireless network that will provide different SSIDS to various parts of a campus.  Since it is open to the public, I can't use an assignment raius Server vlan dynamic.  Anyone know if I can do with one controller or will it take a controller (or redundant pair) for each zone?  Thank you!

  From liberation WLC 5.2 and later versions, you can have a lot (I'll have a doubt whether it is 255 or 512) SSID configured on the WLC. Given that you can have up to 16 on an AP, you can then assign some SSID for some APs.

  The key is to configure the AP group.

  An AP group defines a list of access points, which SSID these APs are maintenance and what interface they use for each SSID (the default interface mentioned in the config SSID or a substitution).

  So you can have one SSID on your entire campus, but different groups AP it will link with different interfaces. I think that's what you are trying to reach.

  Nicolas

• Parameters of different Cluster OR XNET (Hex 0xBFF6309A)

  I've updated OR XNET on my system and the goal of rt and now I get this error:

  Pible reason (s):

  NOR-XNET: (Hex 0xBFF6309A) interface has already been opened with different cluster settings as those specified for the current session. Solution: Make sure the settings of the cluster of agreement for the interface, or use a different interface.

  MPCC,

  Can you click the CAN Port in the system definition and make sure that the Cluster settings have been kept?  I saw this option to reset before.

  

• same circuit design-different versions of multisim now fixed

  again the circuit model 74LS244N, now the pattern16t file works in different versions of multisim.

  How do you pattern16t signs might be useful.

  This circuit is interfaced with gpib, scsi, usb computer interface circuits.

  It's everything. software must always be carried out for each computer.

  Basically, there are computers with a different interface.

  Richard

  Hello

  The application seems interesting to interface with instruments or devices with these buses. Of course, it must take into account the fact that there are off-the-shelf products that come with the drivers, etc.

  Also, I really liked how you have organized the scheme in Multisim with bus, etc.

  Kind regards