Digital Cable Set Top Box connected to the Media Center computer, forced to keep MC on the use of channels 3-cant TV Guide in Media Center to record

Similar Questions

• Toshiba WL863 takes too long to start and its Set Top box problem

  Hello

  Aside from no YouTube on the TV - is not a real question

  I have 2 problems with WL863 TV:

  1. the TV takes long time to turn on (between 2.5 and 4 minutes).
  2. the sound of the TV from a Set Top box (HDMI) changes from time to time, as if a low-pass filter has been activated, living just a whistling noise, but returns to normal every few minutes.

  I use the latest firmware.

  This would have something to do with the settings, or do I have to send the TV for repair under warranty?

  Please give some suggestions.

  Thank you

  > 1. The TV takes time to market (between 2.5 and 4 minutes).
  Have you noticed that in the past, or the first day of purchase?

  If not, I recommend you load the default settings (reset) TVs and check it again.
  In the case where the reset won't help you, it might be that a question and device TV related material must be verified by the service agent.

  > 2. The sound of the television to a Set Top box (HDMI) changes from time to time, as if a low-pass filter has been activated, living just a whistling noise, but returns to normal every few minutes.

  This problem could be linked to the connected Set Top Box and not the TV device.

  TV receives the audio signal from the external, connected HDMI (in your Set Top Box case) device. Check if the same audio issues would be noticeable by using another external device like a DVD or BD player. In case the sound issue would be noticeable only with decoder, the question isn't related to the TV, but to the external device.

• "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".

  Original title: when setting up Windows Media Center, I get the error message: "IR hardware not detected".

  I have an internal TV Tuner that has been installed by HP, when I bought recently a "computer build-your-own." (According to the control panel Device Manager, my tuner is a Win TV HVR 1290, made by Hauppauge). The computer came with Windows 7. While installing Windows Media Center, after setting up the TV Signal (on channel 3) I am able to see a video thumbnail on my computer screen. I am also able to change the channel using my remote control U-Verse (not the Windows remote control supplied with the computer). So far so good! I then hit next and get the following message: "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".  After you receive this message, the installation procedure is completed. I called HP that support intalled the tuner. They had not the slightest idea what to do. I then called Hauppage customer (manufacturer of TV Tuner). They said that I need to plug one end of the IR Blaster cable that shipped with the computer in a slot in the back of my computer (they told me which slot). They said so to run the IR all the way cable to my cable box and the other end of the cable to my cable box of band. They said it was necessary to be able to use my Microsoft Remote to instruct the box to change channels (cable IR stuck on the box). I told her that I did not use the Microsoft Remote, I could change the channel with my U-verse remote (that I preferred to use anyway). He said that it took the cable on the band decoder in order to remove the error message and the installation of Windows Media Center. I then called U-Verse technical adapter who informed me of their set-top boxes (made by Cisco Systems) do not have the ability to receive signals IR IR Blaster cable (or any othe IR signal source). Microsoft is apparently not understand how U-Verse set-top boxes are designed to work and sells a product incompatible remote control/IR. My question is this: How do I set up Windows Media Center, in order to avoid getting the error message "IR hardware not detected" when you install Windows Media Center and just use the remote control of the U-Verse that I prefer to use in the first place. Once understand you this point, please send the information to HP, At & T U-Verse and others. Thank you.

  Ron, I have something for you!

  and for all the people who have this problem :)

  Hi, I had the time of IR not detected in Windows 7 Ultimate with a TV wonder 650 card and a box of digital adapter from Verizon for my PC... Go on the road to installation and after the Media Center channel search, choose manual configuration. Choose the aerial signal (I aso picked after this analog) l. After he sought more, he finds no channels.  Do not be afraid. Just accept it and go to the main settings page in the Mediacenter. If I remember correctly, then select TV Guide. Choose Add channel. I added the channel 3.

  Since my Verizon box has no IR for the computer, I added the channel 3 for the media Center and I change the channels with my Verizon remote. All my stations in the Verizon box go to Channel 3.

  The story here is so, for some reason any Windows detects that only my box channel signal TV and you must manually configure the media center on the air, then go to settings and add the channel you want in the guide.

  Why the guide TV control which channel you can tune is beyond me, but the scanner locks all channels, it does not detect. they must be added manually in the guide.

  My TV works and looks okay now.

  It actually works!

  the only problem is that it is not in HD

  but there is something

  
  

• Windows Media Center didn't recognize Cisco/ATT Uverse Set top Box remote

  With Windows 7 Media Center throughout the TV Setup Wizard, everything works until the screen of the decoder.  Automatic set-top box set up does not work.  Through the screen to identify my decoder does not work.  There is not an option for Cisco (there are 361 other).  It seems that Cisco should be on this list.

  Using the function "learning" remote does not work either.  Media Centre telling me that it does not recognize the remote.

  There is information on the web about this, but I have not seen an emphatic solution.

  Thanks for your insight into this problem.

  Please visit this link

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/able-to-see-live-TV-in-Windows-Media-Center/06193a43-D267-4B34-8e9c-5248bc424473

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/att-cable-box-Cisco-MN-ipn4320-wont-work-with-WMC/bb6684bd-628c-4F63-be82-fb800e71f5bd

• Driver for Motorola Set-Top Box QIP6416 to Windows 7

  I would like to take the a/v out of Verizon Set Top Box (QIP6416-2) and use Windows Media Player to watch cable (FIOS) TV using the Line In input for a card CREATIVE Audigy.

  Thank you

  I would like to take the a/v out of Verizon Set Top Box (QIP6416-2) and use Windows Media Player to watch cable (FIOS) TV using the Line In input for a card CREATIVE Audigy.

  Thank you

  Art

  You may be able to find the necessary help in the link provided below.

  http://www.Verizon.com/support/Residential/TV/fiostv/Receivers/User+guides/User+guides.htm#.

  Set up and install.

  http://www.Verizon.com/support/residential/TV/Setup.htm

  Quick Guide to Verizon

  http://www.Verizon.com/support/residential/QuickGuides/index.htm

  If you wait long enough on the installation and install the page, you will get a popup offering help via a chat.

• How to connect the Qosmio G50 for set-top box

  I just got a Qosmio G50.
  I am trying to connect to media player via my cable box.

  The manual says to connect via an rf cable.
  But as the signal is provided by cable SCART, of course, this won't work.

  Anyone has any suggestions as how work around this problem.

  Thanks in advance

  I agree with Akuma.
  Check the connections you may want to use a different connection.

  If you use an adapter, this could make problems.

• Satellite M40-230: what cables are needed to connect to the TV

  Hello

  I went to PC World, where I bought my M40 and asked them for cables to connect to my TV using the s-video connection on the back of my laptop.

  They said that this was not possible because S-video does not sound.

  Does this mean that I have to get a separate cable for audio to use via the speaker/headphone jack?

  Please let know us that it is a little confusing.

  Thank you, George.

  Hello

  As far as I know it of possible to connect the laptop to the TV with an s-video cable.
  The dealer is right, but there are different s-video cables.

  You can use one with s-video on one end Jack and taken 3 RCA (2 audio and 1 video) on the other end of the cable. Or you use a SCART instead of the 3 Sockets.

• Cannot authorize Digital Editions - says could not connect to the activation server

  I use Adobe Digital Editions 4.5 on a Windows 7 computer.

  I was using Adobe Digital Edition to read library books, then decided to allow if I could access my library of books about elsewhere. I downloaded a few books, and then I started having authentication errors. I couldn't erase the authorization through Adobe Digital Editions to try to do it again, I kept getting errors. I followed the instructions to change the registry, which withdrew the authorisation of old, and I can now, select "authorize computer". But when I enter my Adobe ID and password, I get the error message:

  "Digital Editions cannot connect to the activation server. Please make sure that you are connected to the Internet. »

  My computer is connected to the Internet - that's how I am connected to this discussion. I've uninstalled and reinstalled the software, Adobe Digital Editions, and the same thing happens.  Any suggestions? I prefer Adobe Digital Editions alternatives, but if this activation problem can not be solved I won't have the choice.

  I read through other similar positions and found one that says what they uninstalled 4.5 and installed 3.0 instead. I did this and was able to authorize ADE (no internet connection problem) and again to download eBooks from our library.

• 450 HP: how to connect my laptop to Auntie sky set-top box with an HDMI cable

  piease tell me how

  Hello

  Your laptop has HDMI OUT and your decoder has ALSO HOMI out, you cannot connect two PORTS together, it doesn't

  work. It is the only one?

  http://www.honeytechblog.com/Tata-sky-plus-HD/

  Kind regards.

• Network Diagnostics cable - A is not connected to the Local Area Connection network adapter

  All the links are perfect - network card appears in Device Manager and work - ping 127.0.0.1 but seeing none on in the network connection - cable works in another system - I unplugged the power cables one night and restarted but no result-help solve this problem

  Hello

  Follow the steps in troubleshooting section and check if that helps:

  Network adapter problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

  Also read these articles and check if it helps:

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/using-Windows-Network-Diagnostics-event-logs-to-solve-network-problems

• Is it possible to have the accordion of top boxes smaller than the content of a menu drop-down?

  I am trying to create a drop-down list for my desktop site. The problem is the roll over area covers the other links (on us and facilities). Is there a way to make the box expanded content or the first dropdown to be narrower than the content area? Or is there a better way to implement?

  Thanks in advance!

  

  Have you tried composition of the ToolTip? In the composition of the balloon, the size of the trigger and target are not interrelated.

  And you can also hide the target area once you have finished the design by unchecking 'Lightbox see the part when editing'

  The only thing missing here is the transition as ToolTip composition has an effect of discoloration.

  Concerning

  Vivek

• receive the error code 2001 while restoring the iPhone. in fact, he fell into the water and apple and iTunes logo display and cable when it is connected to the macbook air. Please, help me get through this. Thank you

  http://

  2001 error is usually associated with USB. However, liquid damage probably plays a large role in this case. Take a go-Genius Bar or your local Apple authorized Service provider. -AJ

• black boxes flashing when the use of the computer

  I'm flashing periodically small black boxes on the screen while I use the computer.  Box has no anytthing wrote in it but just flashes quickly and disappears.  Please help me fix.

  Hello

  Did you change your computer?

  Method 1:

  Step 1:

  I suggest you to check in safe mode and perform the clean boot and check.

  Advanced, including safe mode startup options

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Step 2:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 2:

  I suggest to download and install the Microsoft safety scanner and run the scan and check.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

• Web Client connection with the "Use Windows logon credentials" error

  Hello

  I tried to configure vCenter Server appliance (suse) 5.5.0b.

  I created a user in the console of bash and permissions added to it with access complete the server vcenter (with multiplication), added to the Group administrators and users etc.

  When I manually enter credentials to connect it let me, but when I check the "Session using Windows credentials" box produces an error message:

  «The authentication server has returned an unexpected error: ns0:RequestFailed: IDM threw an unexpected error during authentication: platform Native Error [code: 1213] [] [ERROR_INVALID_SERVICENAME].» The error can be caused by a source of identity with a malfunction. »

  I have the same credentials on my computer as in vcenter (the two without configured AD) [this works with vcenter on windows 2008 server].

  I heard it could be the problem of the lack of reverse dns lookup, but I works perfectly.

  vCenter server and dns server are on the same subnet.

  I know there is already a discussion on this error, but the solution is not sufficient (I use American English characters and as I already said - it works on different vcenter).

  Can anyone help?

  Thanks in advance!

  Here's what I got from support that clarifies the case:

  "Design when we choose 'References using Session Windows' respective user name and password is sent to vCenter using the Kerberos authentication protocol that only works when the Client and server are joined to a common domain.

  The reason why we are getting the error reported in your environment is that key Kerberos for the host of the server vCenter application are missing from the/etc/krb5.keytab file. So, I confirm that we will not be able to make the "Session using Windows credentials" option to work in Client and server only not part of the domain.

  To learn more on Kerberos authentication, see Microsoft Link below.

  http://TechNet.Microsoft.com/en-us/library/cc780469 (v = ws.10) .aspx

  "

• I can't erase MESSAGES SUPPRIMES box by removing the use of messages. __UNKNOWN ERROR place __How can I clean my Inbox MESSAGES SUPPRIMES in Windows Mail?

  Problem with Windows Mail

  Unknown error occurs whenever I am trying to remove the contents of the box of MESSAGES SUPPRIMES.

  Thanks for your help.

  Problem with Windows Mail

  Unknown error occurs whenever I am trying to remove the contents of the box of MESSAGES SUPPRIMES.

  Thanks for your help.

  I wonder if it might help...

  Open Windows Mail > menu bar, file > work offline.
  You can delete content in the deleted items folder now?
  Don't forget to put it back online by checking a work offline.

  t-4-2