Digital output is not 5V when connected to a circuit

Similar Questions

• GPIB has not detected when connected to the internet

  Hello

  I have keysight power supply connected to the PXI-8880 via GPIB, it does not detect when it is connected to the internet & it was detected when its not connected. Any body can help me to solve this problem.

  Hello

  This problem occurs because of a conflict in present multiple network adapters in the system. It was a question that has used for detection of targets ethernet to the system that has been resolved. But then this question has also resolved to do the same thing. You can follow the link on how to change the order of the present network adapters in the system.

  http://digital.NI.com/public.nsf/allkb/FD9E1AF5AB1343098625736F0076DE6B

  You must also make sure that the IP addresses of the network adapters are different, otherwise conflict can happen also.

• PCIe-7842R (series R FPGA) digital output does not work properly

  Greetings,

  I'm having some problem show TTL the correct voltage with my PCIe-7842R FPGA board.

  The block diagram of my code FPGA LV Moose appears in "analog - digital .png '. The idea was to convert an analog input (decimal value) to a binary code and 16-bit output by 16 DIO ports. I use the connection block SCB-68 has as the terminal and trendy on the FPGA 1 connector RDIO with SHC68-68-RDIO shielded cable.

  The compiled code ok. But during the test, I noticed that some ports has no output TTL levels correctly. For example, for input 1000 decimal, I would expect binary code 0000001111101000. However, some ports (DIO #6, #7, #9, etc.), which are supposed to ~3.3V (1 digital) high TTL output, output actually 0.8V. I have attached the result measured in 'exit digital test.png '.

  To ensure that the question was not because of the code of the LV, I did some more tests on DIO #6 with a simple example (simple digital output.png). The output was ~ 1V this time at the digital 1.

  It's really confusing because of the digital Edition is supposed to be simple. I used the same FPGA card for controlling roller shutters with TTL signals before and it worked fine.

  Does anyone have similar problems? Any suggestions are greatly appreciated.

  iron_curtain wrote:

  DIOs are connected to a controller digital galvo Cambridge Tech. But I measured the voltage at the terminals of the connector block.

  If you unplug the controller galvo DIOs, do they look good (have the right voltages).  Do you know how many of these entries to the need for controller?  I think you hit the limit the total current available for EID within the Council.

• HP Officejet 7310 all-in-One: printer does not print when connect you to the router

  I can't print from a Mac book pro wireless connected to dsl ATT modem/router.  My printer, HP Officejet 7310 is connected to the router with an ethernet cable.  I can print a test page from the laptop and see my supply rate.  When I try to print an e-mail or my word processing, I get my printer icon on the desktop that said it printer, no error message, but printing does nothing.

  I use the latest driver from apple, 2.0.4 and I have installed and uninstalled the printer numerous times and I

  Download the software twice.

  The HP network configuration page shows the same IP address of the printer, as does the router.

  The printer works fine if connected to the laptop.  If I connect the printer to my mac mini, which is also connected to the

  router by an ethernet cable, I can print from the laptop.  What is going on?

  Hi @TimL2,

  Welcome to the HP Forums!

  I noticed that you can not print with your HP Officejet 7310 when connected to your router. I'm happy to help with this problem!

  Please, try the procedure described in this guide, "printer offline" or "printer not responding" Message (OS X)and let me know what happens!

  If this, or one of the posts on this thread, helped you to solve the problem, please click 'Accept as Solution' said post. To show you 'like', or that they are grateful for my post, please click the thumbs upwards below. If there is anything else I can do to help, please don't forget to let me know!

  I hope this guide is useful!

• iPhone not charging when connected to the computer via USB

  Original title:

  I use windows 7, when I connect my iphone to laptop, it does not load .i don't know it's because of device drivers not installed.when I connect my phone to another laptop its load.  Thank you

  Hello

  1. are you facing problems with USB devices?

  2. that you get an error? If Yes, what is the exact error message?

  3. is your phone detected in iTunes?

  4. doesn't Windows detect the iPhone as storage medium?

  5. are you aware of any changes made to the computer, before the show?

  Method 1:

  Run the hardware troubleshooter and check the issue.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:

  Try to plug it into a different USB port and verification.

  Method 3:

  Check out the following link.

  iOS: device not recognized in iTunes for Windows

  http://support.Apple.com/kb/TS1538

  I hope this helps.

• 'not supported' when connecting computer to TV

  Original title: HAVING BAD RELIANT MY COMPUTER to MY TV Please HELP IF YOU CAN!

  When I try to connect my computer to my HD TV it says no 'supported '. I'm confused because I always connect my computer to my TV to watch movies online, but now for somereason I don't know why it is not currently supported. I tried to change the resolution to the most humble, above and between the two, but still can't seem to find the problem, please help someone... Please, thanks in advance!

  Hi Christine,

  -What is the exact error that you receive when you connect the computer to the television?

  Most likely your Windows is set at a too high resolution for your TV to manage. When a TV meets a too high resolution display, it displays nothing.

  Please try the steps mentioned by Aziz N in

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/format-not-supported-cannot-connect-the-computer/c0508fc0-2851-43C1-95bc-b059a404c0b6?msgId=93bc69bc-3D40-4174-9527-a2d47a0eaa04

  http://Windows.Microsoft.com/en-in/Windows7/connect-your-computer-to-a-TV

  Hope this information is useful. If you have any questions, please let us know.

• Why Adobe Digital Editions does not freeze when I try to download an e-book from the public library?

  Adobe Digital Editions 4,5.1 gives a message not responding when I try to download an e-book from the public library

  How to open the e-book Digital Edition?

• R7000: UPNP Renderer not visible when connected via WiFi

  Hi all

  I use the R7000 as a router and I have the problem that my UPNP renderer (Denon DNP-F109) is not visible if connected via WiFi (via Ethernet, everything works very well).

  Can someone give me a clue what to do here?

  I went on DHCP and UPNP in the configuration. All UPNP (Server/converter/controller) devices are in the same 192.168. * network.

  Thank you very much

  Stefan

  Hello Stefan,

  Please perform a reset of the device and check again if still the same problem.

• T6i does not appear when connected to Windows 10 PC

  I plugged my T6i camera to my PC with the supplied cord, but the camera is not displayed on the PC.

  I'm on Windows 10 with the camera 1.0.0 firmware version (I don't know if there is a newer version of the firmware)

  Device Manager does not display badly connected devices.

  Any help would be appreciated.

  Thank you.

  Solved.

  WiFi should be disabled on the camera.

• my digital TV show no signal when connected to the hdmi to my hplaptop port

  I plugged the hdmi to HDTV cable end and the other end to the hdmi port to my laptop HP in the off-mode, then I turned the laptop and the tv on and seledted in my TV HDMI input signal. After that a few seconds tv monitor displays the data recovery then it comed no signal .do I need to make changes in my hplaptop pls help to solve this problem. Thank you.

  Hi spkmd,

  Follow these methods.

  Method 1: Check with the manufacturer for the software update of the HDMI driver.

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  Method 2: There may be a combination of keys on the laptop to change to HDMI manually, usually a FN + F # combination. You'll need to refer to the documentation for the laptop to which key can control the HDMI. Also, check the manual that came with the TV.

  Method 3: You can also go into the display properties and change the default view for the HDMI. To check the display properties, follow these steps:

  (a) click Start, then Panel.

  (b) click appearance and themes, and then click display.

  (c) in the settings of the display properties dialog box tab, click the icon of the monitor that represents the monitor you want to designate as the primary monitor.

  (d) click to select the use this device as the primary monitor check box. Note that this check box is not available when you select the icon of the monitor that is currently set as your primary monitor.

  For more information, see the following link:

  How to configure and use multiple monitors in Windows XP

  http://support.Microsoft.com/kb/307873

• Satellite Pro U200: VGA output works not properly when the AC adapter / CC has been connected

  Hello

  I have a problem with vga output. When I'm working on the battery and connect my laptop to external monitor is ok, but when I connect adapter then start waving also bluetooth and wlan is not working properly. In other cases when I disconnect laptop battery and connect the AC adapter it works correctly.

  Thanks in advance

  Hello

  Can you please describe more precisely what is happening here? Does not properly is a rather general statement.

• YouTube will not play when connected to google but will be if he is not signed in

  After all of the options to solve the problem it seems that when signed into my google youtube videos account will not play. The video remains darkened. If not connected to google video accounts works very well.

  It is possible that you may need to delete old cookies from the site. Go to the Firefox Menu, click on Options > privacy > show Cookies and click on remove individual cookies. Search Youtube and delete all the.

  If it continues, please also try to upgrade Firefox to 33 and disable hardware acceleration in flash.

• Satellite L855-150 - USB3.0 External HDD does not work when connecting to USB3.0

  Hello

  I tried 2 times to get a SATA-online work drive HARD USB 3.0 adapter when it connects to the USB 3.0 my L855, but each time it failed.
  First time Windows has recognized a new USB device but didn't install the new HARD drive (HARD drive was taken from my desktop PC and fully functional) second time the USB sound jumped upwards, but after then nothing happened.

  Now, I wonder if there is something wrong with the laptop.

  Can you please tell us what adapter are you using?
  Are you using the original pre-installed OS that you got with your laptop?

  To be honest I n t think that there is a problem with your laptop. It will be interesting to know if there is a problem if you use USB3.0 devices and not some cards.

• iPhone is not syncing when connected to the macbook.

  My iPhone is not connecting to iTunes and when I hook it up to my MacBook Air and maintains a load beep.

  I would like to try a different cable or usb port

  If she has always been the case then I suspect the connector in the iPhone to be vice or have some Lint and dirt inside

• iPhone not charging when connected to the USB power adapter

  Hello. I have a 5 s iPhone that I bought used a few months ago. It works very well.

  Normally I charge it by connecting it to my Mac via a USB cable. Last night, I tried to recharge by connecting Apple USB power (also called a power outlet) adapter, which plugs into the wall, supplied with the phone. (Here's a link to the adapter if you are not sure what I'm talking about:.) When I connect the iPhone to the power adapter, I saw that the phone is charging - there was the small icon representing a lightning bolt near the battery of the iPhone.

  However, when I woke up in the morning, the iPhone has been charged only 47%. I don't remember what the percentage was when I plugged into the power supply last night, but I don't think that the phone at that time was much less.

  So I wonder: nobody knows what went wrong? Is there a way to make sure that the phone is loaded with the adapter?

  Thank you!

  M

  If there is a symbol of bolt of lightning next to the battery icon, then the phone should be in charge.  If it is charging a single source, but not another, then the problem is with the unpaid source.  Try another adapter to confirm.