Disagreement of Tektronix TDS 3000 VISA and pilot

Similar Questions

• Tektronix tds 3000 invert channel

  I use the drivers to configure the oscilliscope between two experiences that I often change. I got wor except here n;' t seem to be a function to define a channel Invert on. There is a function matjh which claims to have some sort of invert but does not work. Any help?

  It is a simple way to setup just read of the oscilliscope?

  You can use the Write VISA function to send theCH: reverse the order (where is the string you want to reverse. The MEASURE? query returns metrics. Consult the manual of the TDS3000 programmer.

  Ben64

• Urgent: oscilliscope Tektronix TDS 2014 B USB communication interface

  Changed the code from a GPIB interface to the oscilliscope to a USB (Tektronix TDS2014B) and now the code will not work. The VI is not the scope triggering. I checked the USB interactive control of VISA address and it matches the block diagram. I get this error:

  VISA write to Tektronix TDS 200 1000 2000 Series.lvlib:Error Query.vi-> Tektronix TDS 200 1000 2000
  Series.lvlib:Close.VI-> 200 1000 2000 Tektronix TDS Series.lvlib:Initialize.vi

  Help, please!

  Do not take account of this post, I left my signed account and a graduate, decided to ask a question on my behalf. The oscilloscope just need a reboot.

• Installation of NI-VISA and NOR-488. 2 on Mac

  I have a new Mac on which I am trying to install instrumentation OR (VISA and GPIB) pilots, and things don't work any tips would be appreciated. I downloaded the most recent version of these two (14.0 visa) and 3.0.1 for the GPIB, ran the installers (restart the computer between the two installed) and then tried to run the VISA configuration utility and the GPIB configuration utility to verify that the drivers were ok (at this point, no measuring equipment is attached to the machine (ultimately, the material will be a USB-> RS232 adapter and a USB-> adapter GPIB).

  The two configuration utilities crashed running. Config GPIB obtained in what concerns to the top of its window and then crashed a few seconds later; NI-VISA never even managed to finish to display the home screen.

  In reviewing reports of incidents, accidents seem to be in the OR-PAL driver at low altitude. The report indicates that

  / Library/Frameworks/nipalu. Framework/versions/1/nipalu

  Abort() called

  Poking around the list of files mentioned in the uninstall NOR-PAL guide, it seems that the kernel extension nipalk.kekt was not actually installed correctly (it is absent of/Library/Extensions and/System/Library/Extensions, and according to the uninstall folder, it should be present in both. I tried to copy the kext above a machine that does not have a functioning VISA/GPIB install, but OSX refused to load because it has not actually been installed.

  My plan right now is follow the uninstaller for VISA, GPIB and NOR-PAL and then try to run the installers, but I fear that I will end up in the same place. Y at - it something special or something needed to get these drivers to install correctly (i.e. should things be installed in a specific order, should I try to install VISA 5.4 and then do an upgrade installation 14, try to sacrifice a goat, stuff like that)?

  The material is a Mini Mac OSX 10.9.5 running.

  Thanks for any help.

  And just to follow up with a few additional details, I went through the same procedure on a second Mac that was fresh out of the box. When running Setup for NOR-488, one of the things that we tried to install was an "Update" the subsystem NI Core Services of pilots. This was despite the fact that the VISA facility has implemented a much newer version of the kernel drivers.

  Thus, it seems that the problem is that NEITHER-488 Setup does not correct version control before overwriting the subsystem of pilots. He obviously checked that the driver has been installed, since the action has been listed as "update" instead of "install".  At least in principle, running the installer of NOR-488 first, then the VISA installer should work, but for some reason some the only time where I tried in my tests, it did not work. Maybe, I haven't had a full work of sanitation among other failed attempts. Just for the record, is the sequence that seems to work

  (0) remove all traces of any agreement, failed to install. Follow the steps described in the files uninstall.txt for NOR-488. 2, NI-VISA and NOR-PAL. The uninstall for this latter guide is located in/Library/Application Support / National Instruments/NOR-PAL

  (1) perform a standard installation of NI-VISA 14.0. Restart the computer. Check VISA works (just run the config utility)

  (2) perform a standard installation of NOR-488. 2 3.0.1. Restart the computer. The VISA and GPIB crash when access

  (Optional) curse (2A) to the length

  (3) perform a standard installation of NI-VISA 14.0. Restart the computer. The VISA and GPIB should now be functional.

  Tested on a pair of 'Late 2012' Mac mini OSX 10.9.4 running. One machine was Labview 2014 before you install the drivers for the instrumentation, the other had not installed LabVIEW.

• you want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. A

  I want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. After that, I want to arduino to send out necessary via a serial port to labVIEW which should be read using visa read and store in a chain. While I am able to write or read both individually, I can't do it consecutively. I used advanced read and write vi for checking my code, but nothing is helping. The wrong bed 'time delay before execution. " Please let me know where I can go wrong. Also is it possible to write code for hx711 using labVIEW

  1. you need not "\n" on your orders println().  This command adds an end of line character already in the message.

  2. you get the error because you have a loop around your reading.  After the first reading (well technically, the second because of you add an extra line end character), there is nothing left in the port.  As a result, you will get the timeout.

  3. you should really consider using a Structure of the event.  This way you just don't write and read when you press the Write button and you can also use the structure of the event to make the loop to stop.  I also go up to close the port inside the stop-> value Change event.

  

• Error with Visa and USB device

  Hello

  I am currently working on a VI to use visa to get information from a USB device. The device is a digital-line tachometer.

  I was able to get the drivers USB and everything set and the device appears in MAX, but now I get an error after the open block of visa, and I don't know why.

  Any ideas would be greatly appreciated, but I don't know that anyone will be able to do, because you probably don't have the same one.

  VI is attached

  
  

• Serial port visa and while loop

  Hello

  I am trying to acquire data of a device through serial communication. This is an RS232 interface. I use a port of visa and I know open and close the port of visa again and again while the program is running is bad style. So, I trieed to use a while - excluding the Visa open loop and nearby (see the attachment of a second, program 2). Unfortunately this work of isn´t program and I can´t find the bug. However the first attachment (program 1) works properly (except that the speed is maybe more low). Sombody could me to get the second work programme.

  Thank you!

  Best regards

  Soffi

  What you need to do is to add a register to offset for the name of resource VISA and error. See attachment a screenshot.

  I couldn't find this anywhere in the examples of NEITHER. (This one is based on the basic series example write and read vi.) When I started with LV, I asked tech support how to do this, and they told me. I WISH THEY WOULD SHARE THIS TECHNIQUE WITH USERS IN THE UNITED STATES!

  I hope this helps. (I can reach the vi if you wish.)

  Ed

• Can I install Driver Visa and USB-GPIB on LabVIEW7?

  Can I install Driver-NI-VISA and USB-GPIB on LabVIEW7? Or I need to install LabVIEW8?

  Thank you

  Véronique.

  Veronica wrote:

  Can I install Driver-NI-VISA and USB-GPIB on LabVIEW7?

  Yes.

  Or I need to install LabVIEW8?

  Only if you want to program in LabVIEW.

• What is the interaction between appellant VIs and subVIs using VI Server?

  I am student at the CLAD and one of the lines in the document preparation or here is the following:

  What is the interaction between appellant VIs and subVIs using VI Server?

  I know how to use the function "Call for reference" to call a VI, but not necessarily a Subvi. I thought a Subvi is always loaded with the calling VI and has nothing to do with the server of VI. What Miss me?

  Hi Bmihura,

  I think that this article will clear up how the VI Server works with subVIs called statically or dynamically.

  Call a VI by reference

  Best regards

• Visa and executable

  Hello everyone!

  I have a problem with the visa and files executable labview.

  I did a VI that use a serial port visa and who have a control to let the customer choose with serial port on which he wants to work. The program works correctly in Labview. However this program will be used for one of my colleague whose PC isn't Labview. Then, I made an executable file that also works in my computer. However, not in that of my colleague. He downloaded the runtime (8.6.1) and when it executes the program instead of having a list with all the serial port of the PC, there is only ASRL5.

  How can I get the full list of ports? I think that this error should be tied to the length of the engine operation (because in my PC, everything is OK), but where exactly is the error?

  Thank you!

  Mila

  Hello 1000 has,

  You do not have products installed in trial mode. Please uninstall these products, upgrade the API of VISA for the last and try to create a Setup program.

  Best regards

• I have a Dell Dimension 3000 CPU and I try to re - install a Dell 720 printer. I get the message. "Failed to start spooler log on the local computer. Error 1075: The dependency service is not...

  Original title: Journal of spooler

  I have a Dell Dimension 3000 CPU and I try to re - install a Dell 720 printer. I get the message. "Failed to start spooler log on the local computer. Error 1075: The dependency service does not exist or has been marked for deletion. I tried this diagnosticTo start print spooler service and also long-term arer services set it to automatic, follow these steps.     a. Click Start, right click on my computer and select manage.  b. in the console that opens, expand the menu Services and applications.  c. click Services.  d. click the button twice to spool print.  e. in the 'Général' tab, go to Startup Type.  f. the Automatic value.  g. click on the Start button.  h. click on apply and Ok.     Click the Dependencies tab, and not all the dependency services and repeat the steps above to set automatic and start the service.      Restart the computer after you start the services above. After restarting the computer check if you can install the printer. And a few others. Someone at - it suggestions? This printer has been operational on this computer at any given time. Windows XP Home / Firefox. .:

  Hello

  1. don't you make changes on the computer before this problem?
  2. when exactly you get this error message?

  Step 1: Run the fix it tool using the article below and check out them.

  Problems printing and printing errors
  http://support.Microsoft.com/mats/printing_problems/

  Step 2: Try the steps from the article below and check out them.

  Error message when you try to start the spooler service for printing on a Windows XP-based computer: "error 1075.
  http://support.Microsoft.com/kb/915168/en-GB

• I'm running Windows SP2 of Visa and get the following message is displayed at startup: "sasnative32 file not found Autocheck ignored."

  sasnative32 not found

  I'm running Windows SP2 of Visa and get the following message is displayed at startup:

  'sasnative32 file not found that autocheck ignored. '

  I found this message in the registry and deleted but it keeps reappearing.

  It does not seem to cause operational problems, but I want to fix.  Any suggestions?

  The BootExecute key should contain autocheck autochk *. This measure of Chkdsk to run at startup.

  You have all Tune Up or optimization programs installed? It is possible, it is distributed with a different brand.

  You can determine what is written in the registry key by using the Process Monitor program

  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645

  If you have not used before, there is an introduction to use it here:

  Windows Sysinternals Primer: Process Explorer, Process Monitor and more. Tech· Ed 2010 North America | Channel 9

  If the value has been restored in the register at the time wherever you can connect, you will need to use logging to start. This can significantly slow down the boot.

  You may be able to determine what is responsible for disabling the departure of items using msconfig.

  http://support.Microsoft.com/kb/929135

• How can I ride me Windows Visa and the rank of a XP operating system?

  How can I ride me Windows Visa and the rank of a XP operating system?

  On Mon, 27 Sep 2010 15:26:17 + 0000, Krista Northcott wrote:
   
  > How can I ride of Windows Visa and the rank of a XP operating system?
   
   
   
  You can not downgrade. For XP, you must install XP properly.
   
  When you perform a clean install, it will begin by formatting the
  by car, then you can get rid of everything, including Vista.
   
   
  --
  Ken Blake
   

  Ken Blake (MS-MVP)

• HP dv7 3000 fan and vga & cpu sinks

  Hello, I would like to know if anyone has the part number of the hp dv7 3000 fan and cpu & heat sink vga. It's with intel core i7 and vga gt 230.

  Thank you.

  Hello

  You can find all the numbers from part/codes for your machine of manuals in the section 'Information Service and maintenance' from the following link:

  http://h20000.www2.HP.com/bizsupport/TechSupport/DocumentIndex.jsp?lang=en&cc=us&prodClassId=-1&ContentType=SupportManual&prodTypeId=321957&prodSeriesId=4011368

  Manual also show you to decide or the pieces on your machine too.

  Kind regards.

• OpenManage Version Essentials 2.0 Firmware gather and pilot inventory

  Ive installed 2.0

  I have 2 inventory servers via "iDRAC (server out of band)" "WS - MAN".

  now, I'm trying to collect the inventory FW so I can test the upgrade of the drac fw.

  No matter what I do "error at least select a server.

  but the servers are not displayed... If I create a new group and add them to the group,

  Group is visible in the window "create F/W and pilot inventory task" but when I check the box and try to finish, he says always "error at least select a server.

  

  I am sure that this particular task is required for in-band system updates.

  Looks like you are using out of band (iDRAC/WSMan).

  In this case, I think you're all ready to go.  You discovered via WSMan, now just go on manage | Updates system and you should be able to see your report compliance and update from there.  You have no need for this task, that you try to create.

  Can you let me know if go to the update of the portal page system works for you?

  Kind regards

  Rob

  delltechcenter.com/OME