Display problems - I found the Office to be tight on the right side of the monitor

Similar Questions

• Satellite P100 - display problem after installing the Samsumg software

  Hello

  I have a Toshiba P100-PSPA3 and just bought a new external monitor Sincmaster from Samsung. I installed it yesterday and everything works fine, I just plug in and the laptop recognizes it as a second monitor. Then I noticed the monitor comes with a CD and they recommend you to install the components of this CD.

  I installed the driver and still works fine but then I installed a software called * Magic money *, it is said that I should make a new start, I did and the image comes in the second monitor, * my laptop screen is black.*
  Then I begin to try all the possible solution I had in my head. I open this Magic Tune, and he says that it s not compatible with my computer, so I uninstall it. I have downloaded the drivers from Nvidia, Toshiba, installed again and again doesn´t work.

  I prove with the nvidia settings and the West without change. NVIDIA doesn´t recognize my laptop as a monitor, screen it recognizes just the Samsumg Sincmaster.

  I looked for people with the same problem in other forums and a possible solution was to turn off the computer, remove the battery and press the power for a few seconds, trying to carry out the computer. I did and it didn t work.

  Someone here could give me a light? I m totally lost now and I have to work with my computer in the next few days!
  Thank you very much
  Ivan

  Hello

  This software is not known to me and it is important to say that notebook manufacturers may not support some third part software.

  I put t know if this software must be preinstalled but I'm sure you can use your external display without it. When the external display is connected, you can switch between the LCD and external monitor by using the FN + F5 key combination. If you want to extend the display outside a use Windows display settings. It should work. I tested several laptop Toshiba with a few different monitors in my office and I n t noticed no problem.

  Have you already solved your problem or you are still looking for the solution?

• Chart display problems - cut off the end or shows not all values

  I have a file I/O reads database table where I can choose a date range to view history, and I can't seem to format correctly.

  If I set the width of the graph large enough to show all values, it cuts the right part.

  Width 1200, the value date of end 10/01/2014, shows only until September 24:

  

  Width set at 1700, will now interrupt the rightmost in the values:

  

  Obviously, I want the best of both worlds - when the date range is selected, it shows all the values and fits in the chart area.

  Any ideas?

  Create a diagram with scrolling.

  Under the item add something like:

• Display problems with the Portege R600 and Win 7

  I have a R600 running windows 7, every two minutes, I have a display problem where where the vertical pixels seem to get every centimeter unaligned, so my screen seems to blur digital in bars across it.

  I have an external monitor attached and get the same problem with or without him. I have tired the driver of toshiba and intel driver.

  It seems to go away if I have windows min and max, but sometimes it doesn't. If I run my mouse an affected area, that it seems in trouble and sometimes it's not all screen.

  A refresh solves it.

  Anyone have any ideas?

  > I have an external monitor attached and get the same problem with or without him.
  Maybe I m wrong but in most cases if these symptoms are seen on the two displays (internal & external) then a graphics chip could be affected
  It would be the worst case, because that would mean that the motherboard needs to be replaced

  But just a question; have you noticed that using the previous Windows OS preinstalled by maybe Toshiba (Win XP or Vista), you must install the image of Toshiba again to verify if this display problem is still visible

• The Adobe Reader 11.0.09 display problem

  Hello world

  My operating system is Windows XP Professional SP3.

  I met a strange display issue Adobe Reader 11.0.09.

  The problem happened not only Adobe Reader 11.0.09 traditional Chinese, but also the United States English.

  The display problem, such as the two images as follows.

  

  

  The strange problem was this menu bar, covered by toolbar items or disappeared.

  Please tell me how to solve the problem.

  Thank you very much.

  Steven Hung wrote:

  I had updated the version of Kaspersky Internet Security 2015 and it was up to date.

  Did you update to version 15.0.1.415?  The problem disappeared with this update?

• W510 display problem

  Hi guys, I just bought a W510 and found a display problem when using the battery.

  The display will sometimes dim when using battery power following in the Manager of power Plans:

  • Video playback
  • Maximum battery life
  • Timers (presentation)
  • Optimized power source
  • Energy Star

  This means that, except for the power Plan maximum Performance, the problem exists in all levels of power.

  I post 2 pictures here to make it clear:

  Nomal display

  Display Dim

  Is there someone who has the same problem?

  How does this happen and how to fix it? Thank you!

  Kind regards!

  People call it the problem of 'pixel offset.  See here:

  http://forums.Lenovo.com/T5/W-series-ThinkPad-Laptops/W510-checkered-pixel-patterns-while-running-on...

• C:\windows\ayofeworit.dll the specific module could not be found, the message pops up when loading office

  C:\windows\ayofeworit.dll the specific module could not be found, the message pops up when loading office

  Here are the detailed instructions that protect you and solve your problem in the 'right' way.

  There is very little. DLL files that should be loaded from the C:\WINDOWS folder and is not one of them.  If you can't find a good explanation for the name of the file in a Google search, re chances while your system is currently or has been infected with malicious software.

  A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.

  It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
  Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
  So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.

  You must be sure to solve the problem and not just fix the symptom of the problem by simply relieving your message - system is not a fix (there is a difference).

  If you just locate and uncheck the item in msconfig, which disables the element but does not remove the reference to the element of false starting your computer.   The msconfig program is not a Startup Manager, that's a troubleshooting tool.  Disabling things in msconfig to put an end to the messages and think that your problem is solved is short-sighted and leave behind him a sloppy XP configuration.  Just disable the display of a start-up error message should not count as a 'solution' to the problem.
  If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.
  Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry. There is no cancellation or exit without saving the option in regedit.
  Here is a link to a popular registry backup tool:
  http://www.SnapFiles.com/get/ERUNT.html
  You can also use the Autoruns to find the element of start remains little matter where he's hiding.  Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
  When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner.  Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information
  .  You are really interested only a few sections.
  The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
  Scroll through the list and look for a boot entry associated files in the error message.
  If you can't find on the connection tab, look in any tab.
  You can also click file, search to search for logon, or any tab for all or part of the name of the element.
  Right-click on the offending entry and choose Remove.  If you are not sure what it is, you can simply disable, restart and if the problem is resolved and then remove the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
  Given that you had or have an infection, followed with this:
  Perform scans for malware, and then fix any problems:
  Download, install, update and do a full scan with these free malware detection programs:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.
  Restart your computer and solve the outstanding issues.

• The satellite M60 display problems

  Hello

  I bought a satellite M60 a month ago, and since then, I've been strugling trying to solve a problem that has to do with the display (ATI 700 X mobility).
  When I play some games (the dawn of war, Unreal tournament...) the computer freezes completely, I actually have to force stop it to restart.
  Another problem, that I have seen is with Mixmeister Pro 6, the video playback is erratic, it is as if the computer is unable to handle any overload.

  I tried the upgrade of drivers, nothing works, then I installed the third party Omega drivers, but once again, nothing to do.

  Since the purchase of the M60, I had to correct problems of Wirless and PCMCIA card through driver updates, but there is nothing that I'm be able to do to resolve this display problem.

  I am quite convinced it's a driver issue, but then again, nothing is certain.

  If anyone can help me please I'm getting desperate.

  Hello

  Well, it's not easy to say why it happens but one of my friends has sometimes even appearance but on another unit. If he plays a high-performance games unity cling.
  In my view, this could be a heating problem. Playing games is hard work for the laptop, because all parts (bars of memory, processor, graphics card, etc.) work with max performance and produce a lot of heat. Most laptops are not developed for this.

  However, you should always use the graphics driver from Toshiba. I found the latest version of 15/07/05. It is a display 8.121.050.322A driver. In addition, you must install latest DirectX. I think that it s a 9.1. Check whether the fixes for these games are available.

  Second, if video playback is erratic, it seems that the OS is fully committed.
  In this case, you should check the processes that run in the background of the operating system.
  In addition, try to defragment the HARD disk

  Good bye

• Display problem laptop computer connecting to the TV via HDMI

  I have a Satellite L500 - 19 X and when I connect the laptop to my Sony's Bravia TV, the screen is constantly restless.

  I tried to change the refresh rate, but that did not help. The HDMI cable should not be the problem, because it works very well with my Xbox. The problem is there for both in dual display and expand options display.

  Someone else has the same problem and found a solution?

  Thank you

  > That's the problem for both in dual display and expand options display.
  And when you see the desktop on the TV only?

• Desktop display problem; Why my mouse won't do anything on my display of open office?

  Original title: desktop display problem

  Why my mouse won't do anything on my display of open office? I have a laptop Toshiba A200, andI PC using Windows Vista. I have a mouse Logitech trendy and of course the laptop Snaptics pointing device. The mouse works fine except on the page office itself, and I can't open any icon. I can always open through the windows startup programs.

  Hello

  • What were the changes made before the issue started?

  You can view these methods:
  
  Method 1:

  I suggest you make a system full scan just to be sure.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Method 2:

  If this does not work, create a new user account and check. If it works in a new user account, then probably your user account have been damaged and would need a fix.

  Create a user profile.

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  Now search for the question.

  Follow the link provided below to fix the damaged user profile.

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

• Microsoft Office 2003 in Microsoft vista Ultimate icon display problem.

  Hello

  I have a computer laptop sony vaio with Windows Vista Ultimate Microsoft. I have connected to the external portable hard drive in Windows XP system as a hard drive. I got the backu. After that, I connected the hard drive of my laptop. then after Microsoft Office icons are not showing in correctly. its unknown icon of projection. but my office applications work properly. Can I recharge the icons as a same as before. I use office 2003.

  Can someone help me please.

  I don't know if it will work in these conditions, but you can try to rebuild the icon cache:http://www.vistax64.com/tutorials/117229-icon-cache-rebuild.html.

  If it does not, go to Windows Explorer and check C:\Program Files\Microsoft\Office\ (at this point I don't know what he could tell - perhaps Office 11 or something like that - because I don't have any more than the desktop version and I forgot how the folder structure is named - but you want the folder containining (, all the program icons to start the Office programs) and see if the executable program icons have changed as well.  If not, right-click on each one and then click on create a shortcut (desktop) - do it twice, so you will have one for the office and another to replace the one that is not going to start (and how much more you need based on the number of shortcut icons that you have).  If the icons of the programs also display incorrectly.

  If it does not, then there is no specific functionality of Ofice 2003 (or later versions) to simply change the icons to their original forms.  Try the repair Office option in the:http://support.microsoft.com/kb/821593.  One of the options included (that can be verified) is to restore the desktop shortcuts and which can solve the problem.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• The dvd on the s-video output display problem

  I think I am doing something stupid, but I can't understand it.  I used my T40p for many years, inclunding using the vga external display monitors and digital projectors player.  For the first time, I wanted to use it to view DVDs on a TV using the s-video output capacity.

  I activated the s-video and connected to the tv without problem.  My office is correctly displayed on the TV.  However, when I use the dvd playback software to show a dvd, the tv does not display the content.  The content of the dvd shows correctly on the computer screen, but not on the TV screen.  If I use the view "full screen", nothing shows up on the TV.  If I show only the dvd in a window, then everything on the desktop is shown properly on tv, except the dvd window is blank.  Yet once, it appears correctly on the computer screen.

  I have tried various software to media, including intervideo WINDVD and Classic Media Player player.  I tried PAL and NTSC discs.  No difference.

  I think I'm missing something obvious.  Any ideas appreciated.

  T40p 2373-G3U, 1600 MHz, 1 GB RAM, WinXPP SP2.

  1400 x 1050 with ATI Mobility Fire GL 9000 LCD display adapter display.

  OK, I solved this problem myself.  The solution is to use a configuration that uses ONLY the external display.  Apparently if you enable the output s-video, but do not turn OFF the LCD screen, the video card only then produces the dvd on the LCD, not s-video content.

  There are two ways to select the s-video output only.  Go to settings-> control panel-> thinkpad configuration.  In the window of thinkpad configuration, at the top left, there are five buttons to activate different display configurations.  One of them is "tv only".  If you click this button, the LCD of the computer stops, and the s-video output became active.  Showing a dvd in this configuration using intervideo WinDVD or other programs video display shows the contents of the dvd to the TV via the s-video output screen.

  The other way is to implement a model of custom view using the Director of 'presentation', which is accessible from the 'thinkpad configuration' window described above.  It is available under the "view" dropdown  I created a custom method called 'dvd' that automatically sets the external screen in 640 X 480 resolution.  This is consistent with my standard TV ntsc resolution and avoids the need to change the display resolution before you activate the s-video output.  I choose this plan using the key FnF7 is quick and easy.

  Hope this is interesting to someone out there.

• incorporate the html google calendar display problem

  I have embeded the custom html code to google calendar.   It looks ok on my page in adobe muse,

  showing about 8 colors and different schedules and the default view is supposed to be a week.

  However it not displayed correctly.  You can see my calendar, such as published on

  http://http://farandawayfarms.BusinessCatalyst.com/weeklylessons.html

  my agenda should be very similar to this example I found on the support forum...

  http://http :// www.learnadobesoftware.com/calendar.html

  If I insert the code in the html object several times and publish the page, sometimes I get the correct display.

  but then after the page is opened and closed repeatedly, the display looks like the old link and not the last.

  This seems to be a bug.   I use the beta program, but don't see any indication that I use the new version of cloud, even if I am a subscriber of cloud subscription.   I have adobe muse 4.1.    all my software is installed since my license of cloud.

  I'm trying to go live with this site in a few days, and I need to solve this problem.

  Thank you.

  I think that I found the problem in Google calendars.    After many many many wasted hours on this.    first Muse, and then finally in Google calendars.    I removed 'birthday and events Contacts.  in my calendar.   I discovered that the calendar worked in muse when I was connected to google calendar, but when I wasn't, the formatting was wrong.   After trying several times and comparing it to two years old web calendar that worked, I removed the 'Anniversary Contacts and events' calendar of my view of the calendar.   He appears in design mode and preview of muse and after publication, it is the display in safari and chrome.   I will continue to follow closely.

  Thanks to everyone who answered me and made suggestions.

  concerning

• In the visualization of my photos display problem: I have red spots in different parts of the pictures. Someone knows how to fix this?  I rebooted my MacBook Pro, but it does not solve the problem.

  In the visualization of my photos display problem: I have red spots in different parts of the pictures. Someone knows how to fix this?  I rebooted my MacBook Pro, but it does not solve the problem.

  Details please

  What version of Aperture? Is OS X 10.7.5 as you say correct for your OS? You shoot JPEG or RAW? If RAW device? Wharton has changed since this worked?

  LN

• having display problems with my macbook air, first version of 2015. When I turn on my macbook, after boarding the password, then press on enter three lines (not really they look more like flashes coming from the top of the screen appear) in

  having display problems with my macbook air, first version of 2015. When I turn on my macbook, after boarding the password, then press on enter three lines (not really they look more like flashes coming from the top of the screen appear) in the colors Blue, green and red.

  also when I turn off my laptop just until the display on the top of the screen that is 2 and a half inch thick green line appears and goes about a second.

  help someone?

  Thank you

  Howdy Yaser of zoysia,

  It seems that your screen displays some graphical anomalies when you connect to your user name. I would use these troubleshooting steps in the following article on the resolution of screens:

  Restart your Mac in safe mode to reset the default display resolution.

  If booting safe mode doesn't resolve the problem, reset your Mac NVRAM and SMC to reset the video ports on your Mac to their default values.

  From: get help with graphics issues on external displays connected to your Mac.

  Thank you for using communities of Apple Support.