DMVPN tunnel on a shelf (ADSL Internet access provider)

Similar Questions

• why I don't get internet access? Help, please!

  Why when I connect to my wifi, I'm permitted little or no internet access, but it still shows me trhat I'm connected?

  Hi Chris Naylor,.

  1 Windows operating system you are using?

  2. have you been able to connect to before without any problem?

  3. did you of recent changes on the system?

  Method 1:

  You can read the following article and try to run the troubleshooter and check.

  In the Windows wireless network connection problems

  Method 2:

  You can try to update the wireless adapter and see if it helps.

  Updated a hardware driver that is not working properly

  Method 3:

  Disable IPv6

  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.
  NOTE: You should do this for each network connection.

  Method 4:

  You can also temporarily disable third-party security software and firewalls installed on the system and check if the problem persists.

  Note: Be sure to enable the security software on the computer after checking.

  For more information, you can consult the following article:

  Solve problems, find wireless networks

  Hope this information is useful.

• No Internet access after the connection of the cisco vpn client

  Hi Experts,

  Please check below config.the problem is vpn is connected but no internet access

  on the computer after the vpn connection

  ASA Version 8.0 (2)
  !
  ciscoasa hostname
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  IP 192.168.10.10 255.255.255.0
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  IP 192.168.14.12 255.255.255.0
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  2KFQnbNIdI.2KYOU encrypted passwd
  passive FTP mode
  standard access list dubai_splitTunnelAcl allow 192.168.14.0 255.255.255.0
  INSIDE_nat0_outbound list of allowed ip extended access all 192.168.14.240 255.255.2
  55.240
  pager lines 24
  Within 1500 MTU
  Outside 1500 MTU
  IP local pool testpool 192.168.14.240 - 192.168.14.250
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access INSIDE_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.14.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac setFirstSet
  Crypto-map dynamic dyn1 1 set transform-set setFirstSet
  Crypto-map dynamic dyn1 1jeu reverse-road
  dynamic mymap 1 dyn1 ipsec-isakmp crypto map
  mymap outside crypto map interface
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  !
  global service-policy global_policy
  password encrypted user testuser IqY6lTColo8VIF24 name
  username password khans X5bLOVudYKsK1JS / encrypted privilege 15
  tunnel-group mphone type remote access
  tunnel-group mphone General attributes
  address testpool pool
  tunnel-group ipsec-attributes mphone
  pre-shared-key *.
  context of prompt hostname
  Cryptochecksum:059363cdf78583da4e3324e8dfcefbf0
  : end
  ciscoasa #.

  Hello

  Large.  Try adding the below to make it work

  vpn-sheep access list extended permits all ip 192.168.15.0 255.255.255.0

  NAT (inside) 0-list of access vpn-sheep

  Harish

• No internet access through VPN

  Hi, I have the router Cisco 881 (MPC8300) with c880data-universalk9 - mz.153 - 3.M4.bin when users establish a VPN connection to the corporate network, had access to all the resources but no internet access, please help me what else I need to configure to achieve my goal. I don't want to split the tunnel, internet via VPN, users must have. In my opinion, I have put an additional configuration for NAT, but my router not recognize u-Turn and NAT commands on the object on the network.

  My config:

  Building configuration...

  Current configuration: 13562 bytes
  !
  ! Last configuration change at 09:52:38 PCTime Saturday, May 16, 2015, by admin
  version 15.3
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  XXX host name
  !
  boot-start-marker
  start the flash system: c880data-universalk9 - mz.153 - 3.M4.bin
  boot-end-marker
  !
  !
  logging buffered 51200 warnings
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authentication login ciscocp_vpn_xauth_ml_2 local
  AAA authorization exec default local
  AAA authorization ciscocp_vpn_group_ml_1 LAN
  AAA authorization ciscocp_vpn_group_ml_2 LAN
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  iomem 10 memory size
  clock timezone PCTime 1 0
  PCTime of summer time clock day March 30, 2003 02:00 October 26, 2003 03:00
  !
  Crypto pki trustpoint TP-self-signed-1751279470
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 1751279470
  revocation checking no
  rsakeypair TP-self-signed-1751279470
  !
  !
  TP-self-signed-1751279470 crypto pki certificate chain
  certificate self-signed 01
  XXXX
  !
  !
  Protocol-IP port-map user - 2 tcp 8443 port
  user-Protocol IP port-map - 1 tcp 3389 port
  !

  !
  !
  !
  IP domain name dmn.local
  8.8.8.8 IP name-server
  IP-server names 8.8.4.4
  IP cef
  No ipv6 cef
  !
  !
  license udi pid CISCO881-K9 sn FCZ174992C8
  !
  !
  username privilege 15 secret 5 xxxx xxxx
  username secret VPNUSER 5 xxxx
  !
  !
  !
  !
  !
  !
  type of class-card inspect sdm-nat-user-protocol--2-1 correspondence
  game group-access 105
  corresponds to the user-Protocol - 2
  type of class-card inspect entire game SDM_AH
  match the name of group-access SDM_AH
  type of class-card inspect entire game PAC-skinny-inspect
  Skinny Protocol game
  type of class-card inspect entire game SDM_IP
  match the name of group-access SDM_IP
  type of class-card inspect entire game PAC-h323nxg-inspect
  match Protocol h323-nxg
  type of class-card inspect entire game PAC-cls-icmp-access
  match icmp Protocol
  tcp protocol match
  udp Protocol game
  type of class-card inspect entire game PAC-h225ras-inspect
  match Protocol h225ras
  type of class-card inspect entire game SDM_ESP
  match the name of group-access SDM_ESP
  type of class-card inspect entire game PAC-h323annexe-inspect
  match Protocol h323-annex
  type of class-card inspect entire game PAC-cls-insp-traffic
  match Protocol pptp
  dns protocol game
  ftp protocol game
  https protocol game
  match icmp Protocol
  match the imap Protocol
  pop3 Protocol game
  netshow Protocol game
  Protocol shell game
  match Protocol realmedia
  match rtsp Protocol
  smtp Protocol game
  sql-net Protocol game
  streamworks Protocol game
  tftp Protocol game
  vdolive Protocol game
  tcp protocol match
  udp Protocol game
  type of class-card inspect the correspondence SDM_GRE
  match the name of group-access SDM_GRE
  type of class-card inspect entire game PAC-h323-inspect
  h323 Protocol game
  type of class-card inspect correspondence ccp-invalid-src
  game group-access 103
  type of class-card inspect entire game PAC-sip-inspect
  sip protocol game
  type of class-card inspect correspondence sdm-nat-https-1
  game group-access 104
  https protocol game
  type of class-card inspect all match mysql
  match the mysql Protocol
  type of class-card inspect correspondence ccp-Protocol-http
  http protocol game
  type of class-card inspect entire game CCP_PPTP
  corresponds to the SDM_GRE class-map
  inspect the class-map match PAC-insp-traffic type
  corresponds to the class-map PAC-cls-insp-traffic
  type of class-card inspect entire game SDM_EASY_VPN_SERVER_TRAFFIC
  match Protocol isakmp
  match Protocol ipsec-msft
  corresponds to the SDM_AH class-map
  corresponds to the SDM_ESP class-map
  type of class-card inspect correspondence ccp-icmp-access
  corresponds to the class-ccp-cls-icmp-access card
  type of class-card inspect the correspondence SDM_EASY_VPN_SERVER_PT
  corresponds to the SDM_EASY_VPN_SERVER_TRAFFIC class-map
  !
  type of policy-map inspect PCB - inspect
  class type inspect PCB-invalid-src
  Drop newspaper
  class type inspect mysql
  inspect
  class type inspect PCB-Protocol-http
  inspect
  class type inspect PCB-insp-traffic
  inspect
  class type inspect PCB-sip-inspect
  inspect
  class type inspect PCB-h323-inspect
  inspect
  class type inspect ccp-h323annexe-inspect
  inspect
  class type inspect ccp-h225ras-inspect
  inspect
  class type inspect ccp-h323nxg-inspect
  inspect
  class type inspect PCB-skinny-inspect
  inspect
  class class by default
  drop
  type of policy-card inspect sdm-license-ip
  class type inspect SDM_IP
  Pass
  class class by default
  Drop newspaper
  type of policy-card inspect sdm-pol-NATOutsideToInside-1
  class type inspect sdm-nat-https-1
  inspect
  class type inspect sdm-nat-user-protocol--2-1
  inspect
  class type inspect CCP_PPTP
  Pass
  class class by default
  Drop newspaper
  type of policy-card inspect PCB-enabled
  class type inspect SDM_EASY_VPN_SERVER_PT
  Pass
  class class by default
  drop
  type of policy-card inspect PCB-permits-icmpreply
  class type inspect PCB-icmp-access
  inspect
  class class by default
  Pass
  !
  safety zone-to-zone
  security of the area outside the area
  ezvpn-safe area of zone
  zone-pair security PAC-zp-self-out source destination outside zone auto
  type of service-strategy inspect PCB-permits-icmpreply
  zone-pair security PAC-zp-in-out source in the area of destination outside the area
  type of service-strategy inspect PCB - inspect
  source of PAC-zp-out-auto security area outside zone destination auto pair
  type of service-strategy inspect PCB-enabled
  sdm-zp-NATOutsideToInside-1 zone-pair security source outside the area of destination in the area
  type of service-strategy inspect sdm-pol-NATOutsideToInside-1
  in the destination box source sdm-zp-in-ezvpn1 ezvpn-pairs area security
  type of service-strategy inspect sdm-license-ip
  source of sdm-zp-out-ezpn1 of security area outside zone ezvpn-zone time pair of destination
  type of service-strategy inspect sdm-license-ip
  safety zone-pair sdm-zp-ezvpn-out1-source ezvpn-zone of destination outside the area
  type of service-strategy inspect sdm-license-ip
  safety zone-pair source sdm-zp-ezvpn-in1 ezvpn-area destination in the area
  type of service-strategy inspect sdm-license-ip
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 2
  BA aes 256
  preshared authentication
  Group 2
  !
  Configuration group customer crypto isakmp Domena
  key XXXXXX
  DNS 192.168.1.2
  Dmn.local field
  pool SDM_POOL_1
  Save-password
  Max-users 90
  netmask 255.255.255.0
  banner ^ Cwelcome ^ C
  ISAKMP crypto ciscocp-ike-profile-1 profile
  match of group identity Domena
  client authentication list ciscocp_vpn_xauth_ml_2
  ISAKMP authorization list ciscocp_vpn_group_ml_2
  client configuration address respond
  virtual-model 1
  !
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac ESP_AES-256_SHA
  tunnel mode
  !
  Profile of crypto ipsec CiscoCP_Profile1
  game of transformation-ESP_AES-256_SHA
  set of isakmp - profile ciscocp-ike-profile-1
  !
  !
  !
  !
  !
  !
  !
  interface Loopback0
  IP 192.168.9.1 255.255.255.0
  !
  interface FastEthernet0
  no ip address
  !
  interface FastEthernet1
  no ip address
  !
  interface FastEthernet2
  no ip address
  !
  interface FastEthernet3
  no ip address
  !
  interface FastEthernet4
  Description $ETH - WAN$ $FW_OUTSIDE$
  IP x.x.x.x 255.255.255.248
  NAT outside IP
  IP virtual-reassembly in
  outside the area of security of Member's area
  automatic duplex
  automatic speed
  !
  type of interface virtual-Template1 tunnel
  IP unnumbered Loopback0
  ezvpn-safe area of Member's area
  ipv4 ipsec tunnel mode
  Tunnel CiscoCP_Profile1 ipsec protection profile
  !
  interface Vlan1
  Description $ETH_LAN$ $FW_INSIDE$
  IP 192.168.1.1 255.255.255.0
  IP access-group 100 to
  IP nat inside
  IP virtual-reassembly in
  Security members in the box area
  IP tcp adjust-mss 1452
  !
  local IP SDM_POOL_1 192.168.10.10 pool 192.168.10.100
  IP forward-Protocol ND
  IP http server
  23 class IP http access
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  The dns server IP
  IP nat inside source list 3 interface FastEthernet4 overload
  IP nat inside source static tcp 192.168.1.3 interface FastEthernet4 443 443
  IP nat inside source static tcp 192.168.1.2 8443 interface FastEthernet4 8443
  IP route 0.0.0.0 0.0.0.0 X.x.x.x
  !
  SDM_AH extended IP access list
  Note the category CCP_ACL = 1
  allow a whole ahp
  SDM_ESP extended IP access list
  Note the category CCP_ACL = 1
  allow an esp
  SDM_GRE extended IP access list
  Note the category CCP_ACL = 1
  allow a gre
  SDM_IP extended IP access list
  Note the category CCP_ACL = 1
  allow an ip
  !
  not run cdp
  !
  Note access-list 3 INSIDE_IF = Vlan1
  Note CCP_ACL category in the list to access 3 = 2
  access-list 3 Let 192.168.1.0 0.0.0.255
  Note access-list 23 category CCP_ACL = 17
  access-list 23 permit 192.168.1.0 0.0.0.255
  access-list 23 allow 10.10.10.0 0.0.0.7
  Note access-list 100 Auto generated by SDM management access feature
  Note access-list 100 category CCP_ACL = 1
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq 22
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq www
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq 443
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq cmd
  access-list 100 tcp refuse any host 192.168.1.1 eq telnet
  access-list 100 tcp refuse any host 192.168.1.1 eq 22
  access-list 100 tcp refuse any host 192.168.1.1 eq www
  access-list 100 tcp refuse any host 192.168.1.1 eq 443
  access-list 100 tcp refuse any host 192.168.1.1 eq cmd
  access-list 100 deny udp any host 192.168.1.1 eq snmp
  access ip-list 100 permit a whole
  Note access-list 101 category CCP_ACL = 1
  access-list 101 permit ip 192.168.1.0 0.0.0.255 any
  Note access-list 102 CCP_ACL category = 1
  access-list 102 permit ip 192.168.1.0 0.0.0.255 any
  Note access-list 103 CCP_ACL category = 128
  access-list 103 allow the ip 255.255.255.255 host everything
  access-list 103 allow ip 127.0.0.0 0.255.255.255 everything
  access-list 103 allow ip 93.179.203.160 0.0.0.7 everything
  Note 104 CCP_ACL category = 0 access-list
  IP access-list 104 allow any host 192.168.1.3
  Note access-list 105 CCP_ACL category = 0
  IP access-list 105 allow any host 192.168.1.2

  -----------------------------------------------------------------------
  ^ C
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  access-class 102 in
  transport input telnet ssh
  line vty 5 15
  access class 101 in
  transport input telnet ssh
  !
  !
  end

  I'd be grateful for help

  concerning

  Hello

  Enter the subnet pool VPN to access-list 3 for source NAT

  You may need to check the firewall also rules to allow the connection based on areas you

  HTH,

  Averroès

• Even IOS VPN Interface Internet Access issue

  Hi all

  I was wondering if there was any equivalent to these orders of ASA 5510 to put on a cisco IOS router 2811.

  Split-tunnel-policy excludespecified

  value of Split-tunnel-network-list LOCAL_LAN_ACCESS

  What I want to achieve is to give internet access to my vpn users without creating a split tunnel, which means the vpn user turns off the Internet on the same interface on that their vpn router ends.

  Is a 2811 for this there docs? I could not find the doc for it...

  TIA,

  -Fred

  Try this link

  Public Internet on a stick

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a008073b06b.shtml#intro

  Rgds

  Jorge

• It would work for a WLAN internet access?

  Hi, everyone, I have a few questions about how to implement public access to Internet in our workplace that would not allow access to our local network.  We have several access points 2702 and 2504 WLAN controller.  Two of the four interfaces on the 2504 have intellectual property in the ranks of our LAN subnets.  I assigned a VLAN for public access to the Internet, but do not know how I would implement on our infrastructure past.  Instead, I was thinking about a cable connected to one of the unused interfaces on the 2504 to a port on our DMZ switch and having traffic for the public Internet, out across the demilitarized zone.  If I had to do this way, but also created a scope DHCP for the public Internet, and the DHCP scope were on an interface that had an address on the local corporate network, customers would always get the address?  What is the best way to do it?

  A second question I have is about how the traffic between the access points and the controller is managed.  When a client connects to the access point, their traffic get dug to the controller and then thrown on the LAN, or the traffic goes to the local network directly from the access point?  The reason why I ask is that we have a remote office that we would like to manage the access point of the controller in the Office at home, but we do not want necessarily all their traffic going back or the office, if it was intended for office network at home, or if it is intended for the Internet.  The remote desktop has its own local internet connection and is just VPN'ing to the desktop at home for internal network traffic.  DHCP for clients at the remote office is managed by a DHCP server on the router on this effect.  A remote desktop access point connected to the controller in the head office would be able to use the DHCP server on the router to the remote desktop?  I test that out in a lab environment and I couldn't get it to work this way.  Remote desktop access point is currently running in mode independent and done a good job.  In the future, this site will also get on our MPLS and finally all traffic going to get dug towards the Home Office, including Internet access, so perhaps at that time, attach the remote AP to the controller would be better.

  Thank you!

   A second question I have is regarding to how traffic is handled between the access points and the controller. When a client connects to the access point, does their traffic get tunnelled to the controller and then dumped onto the LAN, or does the traffic go to the LAN directly from the access point? 

  In local mode APs switch always centralized traffic, that is to say CAPWAP tunnel established between AP & WLC. If all traffic comments terminate at WLC connected switch.

  In your case, if you map the traffic comments-SSID to the physical port connects to the DMZ switch, guest SSID users end traffic to DMZ switch. You must ensure that traffic vlan is not go on any other connected WLC trunk ports.

  If AP mode FlexConnect, then traffic will end at the switch where AP connected locally.

  HTH

  Rasika

  Pls note all useful responses *.

• DMVPN tunnel

  Hello world

  I have a few question about DMVPN

  I have a working router hub-and-spoke configuration is. router poke there are configuration on DMVPN tunnel as tunnel source loopback 1. Loopback IP address 1 is 32 10.253.20.X the LAN subnet is 10.168.X.X/24.

  I want to know why we give source Loopback 1 Tunnel and not the local network subnet.

  What is the use of the following commands and these optional commands.

  • PNDH network IP-2000 id
  • tunnel key 100000
  • and tunnel source loopback 1 or ip address

  Also I would like to know if it is possible to tunnel DMVPN configuration between two router or ASA and ASA with version 8.2 or 7.2?

  Thanks a million in advance

  See you soon

  Deepak Khemani

  Hi deepak,

  the command no ipsec nat-transparency udp-program encryption doesn't make use of tcp (default port 10 000) rather than UDP for transaprency nat.

  Other commands creates a cryptographic card to protect the outbound interface.

  Essentially in the encryption card, you have the destination peer (isakmp peers) and the ACL to match traffic to protect.

  In your case, it seems the card encryption protect the GRE Tunnel.

  I believe this because you work encapsultate GRE Tunnel in an IPSEC tunnel, but that causes a lot of overhead.

  I would you recommend that you create an ipsec profile and applies it to the VTI interface, because even if you can make a card encryption with a dmvpn normally, the administration won't be as easy.

  just quick crypto cards vs ipsec vti orders

  Crypto map

  Crypto ipsec transform-set esp - aes ts1

  access-list 100 permit ip src dst

  card crypto map1 10

  defined peer X.X.X.X

  Set of transformation ts1

  ...

  int X/X

  card crypto map1

  now with the vti (assuming that... are already configured in tunnel mode/dest/source)

  Crypto ipsec transform-set esp - aes ts1

  Crypto ipsec profile pf1

  Set of transformation pf1 set

  int tun0

  protection of profile pf1 ipsec tunnel

  I hope this helps.

  Please mark as she answered and/or rate if that will answer your questions

• DMVPN Tunnel and EIGRP routing problem

  I have redundant paths to a remote 2811 router on my network of sites.  The first links is a T1 frame relay connection that has been in place for years, and the new link is on a 54 Mbps fixed wireless that was recently created.

  I'm under EIGRP to my process of routing protocol 100 for the two links.

  I installed a DMVPN Tunnel between the remote 2811 and no. 2851 router on my host site.  The tunnel interface shows to the top and to the top of both sides and I can ping the IP remote tunnel of my networks side host.

  However my eigrp routes are not spread over this new tunnel link and if I run a command show ip eigrp neighbor on each router I show only the neighbor for the frame relay link and not the new wireless link.

  What I'm missing here?

  A tunnel0 to see the shows the following:

  Tunnel0 is up, line protocol is up
  Material is Tunnel
  The Internet address is 10.x.x.x/24
  MTU 1514 bytes, BW 54000 Kbps, DLY 10000 usec,
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation TUNNEL, loopback not set
  KeepAlive not set
  Tunnel source (FastEthernet0/1), destination 172.x.x.x 10.x.x.x
  Tunnel/GRE/IP transport protocol
  Key 0x186A0, sequencing of the people with reduced mobility
  Disabled packages parity check
  TTL 255 tunnel
  Quick tunneling enabled
  Tunnel of transmission bandwidth 8000 (Kbps)
  Tunnel to receive 8000 (Kbps) bandwidth
  Tunnel of protection through IPSec (profile "CiscoCP_Profile1")
  Last entry of 00:00:01, exit ever, blocking of output never
  Final cleaning of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 947
  Strategy of queues: fifo
  Output queue: 0/0 (size/max)
  5 minute input rate 0 bps, 0 packets/s
  5 minute output rate 0 bps, 0 packets/s
  packages of 880, 63000 bytes, 0 no buffer entry
  Received 0 broadcasts, 0 Runts, 0 Giants 0 shifters
  errors entry 0, 0 CRC, overgrown plot of 0, 0, 0 ignored, 0 abort
  output of 910 packages, 81315 bytes, 0 underruns
  0 output errors, 0 collisions, 0 resets interface
  unknown protocol 0 drops
  output buffer, the output buffers 0 permuted 0 failures

  Please go ahead and add a static route on the hub, so it goes through the wireless link and let me know if everything works correctly.

  Federico.

• I need the Java Player for firefox on a stand-alone computer without internet access. I have internet access on another computer. How can I do this?

  I have a stand-alone computer (no internet access) with firefox to run the Java Player. I have internet access on another computer in order to download files and hover over things to the stand-alone computer to install. That do and where can I download and how I install on the stand-alone computer.

  Thank you

  Leroy

  Hi, to get the Offline Installer that you can use on the computer without internet access, please visit https://java.com/en/download/help/windows_offline_download.xml

• How to create network without internet access

  I have three devices: air mac, mini ipad and iphone OS. but I can't access the internet.

  How can I create a network without internet access?

  Maybe I just need another router, but sometimes, I just take my mac and iphone. It is impossible to get the router with me everywhere.

• no internet access at el capitan

  Mac Pro with El Capitan. No Internet access with any browser, but I can access the Internet using the recovery system (this is what I now use to access the site of discussion). Already verify permissions and fix them with disk utility. Other Mac connected to the same router (Apple) can access the Internet without problem.

  It seems I have to re - install El Capitan. Fix?

  How you access the Internet? Wired or wireless? Do you have a good IP address? (Note that the one that starts with 169.254 is NOT good.) What about the access with something else outside of a browser, such as the Mail app? Other devices on your local network can access the Internet?

  Good luck.

• Extend my extreme network with another extreme - waiting for internet access

  Hello - I have a new generation Airport Extreme (let's call it Extreme1) connected to a Comcast modem and it works very well. The extreme will be the router that the modem has no router function. I'm trying to expand my network to another room with another extreme (let's call it Extreme2). I have a connection cable between two rooms. Extreme1 has an ethernet cable from one of its LAN ports connected on port WAN Extreme2. When I try to create a new network with Extreme2 (in aid of the same name, passwords, etc.) it does not work. He was suspended at the end when he is looking for a connection ("Waiting for internet access")-I did the following things based on what I read here:

  1. Changed IPv6 link local parameters
  2. Tried the whole upward on my Macbook and tried on my iphone
  3. The Wan first and then tried to change the configuration after you done for Extreme2 by creating a network
  4. Tried to create a network with Extreme2 connected directly to the modem
  5. Extreme2 factory reset after every attepmt

  And nothing works. Kicker is, I also have a reasonably new airport express and the same thing happens to her as well.

  Do I need to adjust some parameters of network that I'm not aware of? Is it possible that my LAN ports are disabled on Extreme2? It is brand new.

  Thanks for any help.

  Have you used the Apple Setup Assistant?  If you did, it had notified you that the extreme second was being configured "add using Ethernet. The wizard will automatically configure the second airport with the appropriate settings for you.  All you have to do is enter a name of device for the second AirPort Extreme.

  Here I'm assuming that you reset the second extreme to parameters by default until you set it up again and that your second Extreme is the current version of the "tower" or that of previous versions "flat or square.

  The example below shows an AirPort Express as the device which is the extension of the network, but you will see the name of your network and AirPort Extreme on your configuration screen.

  Post back if you need some tips on using the "Wizard" for your configuration.

  

• Office Pavilion Elite e9220y: name of the Internet access when you hover over said tskbr network 5. is that HP name or co cable. ?

  Hello

  I have a desktop Pavilion Elite e9220y Home Premium; Win 7; 64-bit computer.

  I'm wired; but have wireless for other things (Kindle, etc..)

  When I open internet access in the bar of tasks and under the "wireless network connection", I see MY connection (and the name I gave my connection) and 5 solid green bars (no problem).

  Above this section, there is an article with a picture of a House (provided by HP, I'm sure), and he says:

  ' Currently logged on:

  and just below it says: (to the right of the photo of the House) network 5

  and just below it says: internet access

  That's all it lists the wireless network connection with my name and the names of other connections in the district.

  My question:

  the name "network 5"?

  HP says it is my cable provider; my cable provider says it's at HP.

  This can be changed?

  Thank you!

  Hello Denise,.

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

  I understand that you have a problem with wireless networks.

  Windows will think it's in a new network whenever it detects a new router. If you have changed your router or the router configuration. Windows creates a new network. But do not worry.

  If you don't want the name of the connection to be listed under active connection, follow the steps.

  (1) open the "Control Panel".

  (2) select and open "network and sharing Center."

  (3) click on the ' icon "(une icône de la maison pour moi) less 'show your active networks'.". " This will open the dialogue "set network properties." Here, you can rename a network connection or a change as the network connection icon.

  4) click on "Merge or delete network locations" to view the list of network connections that are stored. You can merge or remove connections

  Let me know if it helps.

  Have a great day!

• No internet access on Internet Explorer after upgrade Win8.1

  Hello

  yesterday, I downloaded windows 8.1 but now I have no internet access. When I click on internet explore that was on my normal desktop but I have access to internet on internet explore on the main front page, I can't really use that one, it's very tedious.

  I prefer to use internet in the normal way. Can anyone help?
  Thank you.

  Thread is marked as answered. Is everything OK now?
  I have too many machine with Win8.1 but I don't have this problem. It's okay that surface I use applications requiring internet connection works.

  You can test it with another browser like Chrome?

• Since the upgrade to 5.0, firefox wants internet access to update every day. Why?

  I have McAfee Antivirus Plus, and he tells me everyday since I've upgraded to 5.0 that firefox wants internet access for updating files. Before I upgraded, it didn't happen. What gives? Is - this legitimate, or something is weird going on here? Please notify.

  By default, Firefox is to automatically check for updates every 24 hours.

  • Disable automatic updates, if you wish (Options > advanced > update) and manually check whenever you want (help > about Firefox > check updates)
  • Activate the authorization in McAfee for daily check to occur without informing you (contact McAfree for instructions)
  • Change the frequency of the automatic update checking
    • type of topic: config in the URL/address bar and press the Enter key
    • If you see a cautionary, accept it (promise to be careful)
    • Filter = app.update.interval
    • the default value is 86400 (one day in a few seconds, it's 24 x 60 x 60)
    • Right click on the name of the option in the bottom panel, click on 'Edit', enter your new value, click OK, close the topic: config tab
    • The change may take effect immediately, or you may need to restart Firefox for the changes to take effect, I don't know who.

  You need to update the following. The Plugin version (s) below has / have been submitted with your question and is obsolete. You need to update in order to avoid the known security issues with the version (s) you have installed. Click on 'more system info... '. "to the right of your question to see what was included with your question.

  • Next-generation Java plug-in 1.6.0_21 for Mozilla browsers
  1. Check your plugin versions on one of the following links:
     • http://www.Mozilla.com/en-us/pluginCheck/
     • https://www-trunk.stage.Mozilla.com/en-us/pluginCheck/
     • Note: plugin check page lacks information about all versions of the plugin
     • There are links to tests specific plugin available on this page:
       • http://KB.mozillazine.org/Testing_plugins
  2. Update the Java plugin to the latest version.
     • Download site: http://www.oracle.com/technetwork/java/javase/downloads/index.html (Java platform: download JRE)
       • Don't forget to uncheck the toolbar Yahoo option during installation if you do not want to install.
         
     • See also "Manual Update" in this article for update from the Java Control Panel in Control Panel: http://support.mozilla.com/en-US/kb/Using+the+Java+plugin+with+Firefox#Updates
     • Removal of older versions (if required): http://www.java.com/en/download/faq/remove_olderversions.xml
     • Remove several extensions of Console Java (if necessary): _ http://kb.mozillazine.org/Firefox: _FAQs_:_Install_Java #Multiple_Java_Console_extensions
     • Java test: http://www.java.com/en/download/help/testvm.xml