DMVPN with dynamic failover HSRP/IPSEC
"DMVPN with dynamic failover HSRP/IPSEC."
Hi all. Is this possible? When you use a direct IPSEC LAN to LAN, you have a card encryption and when you secure the card encryption at the source of the tunnel interface, you configure "' crypto map
The DMVPN does not use encryption card, sound by using an IPSEC profile with protection of tunnel. How you configure stateful with HSRP IPSEC in this situation? We're heading for a double cloud dmvpn topology with 2 heads dmvpn geographically separate. I want that every network head to have a redundancy HSRP, which can be done fairly easily. But I also want State IPSEC to be replicated for all security associations IPSEC do not fall in the case of a failover. Is it possible in this scenario and how? Thanks a lot as always. Hello again ;-) There are currently no plan at the moment (that I know) to mix with State redundancy and anythign with protection of tunnel. Frankly it is best to create redundancy in DMVPN termination on both turntable and relying on routing protocols - which I am sure you aware of so I won't bore you with details. That said, my personal observation is - if you want a failover go to ASA, when you have routers, you have all these wonderful tools like VTI/GRE for IPsec that mix well with routing protocols, and MUCH MUCH more. It is very often to change some timers for routing protocol driven "failover" happen very quickly. Marcin Tags: Cisco Security VRF support IPsec with dynamic VTI Hello I am Configuring IPSEC compatible with dynamic VTI e VRF. I followed the guidelines of the document According to the example: "taking VRF support IPsec with a dynamic VTI when VRF is configured under year ISAKMP profile" I should be able to configure the features of the vrf and virtual-model under the same crypto isakmp policy. Unfortunalety, if I try to do, I get the following message R4 (conf-isa-prof) #virtual - model 1 % VRF already set to isakmp profile. Unauthorized virtual model Is anyody knows why I'm not able to follow the configuration of this example? Here's my profile setup and configuration of the virtual model Crypto isakmp profile VRF HAS A Keyring function identity address 192.168.0.2 255.255.255.255 type of interface virtual-Template1 tunnel Unnumbered IP Loopback2 ipv4 ipsec tunnel mode Profile of tunnel ipsec protection has I do the test on the router of runningon 3725 XW3 IOS 12.4 (11). Thank you in advance for advice. Concerning Lukas Lukas, I don't know, but probably this was not yet supported 12.4. The document you're viewing is for IOS 15.2. I don't know by heart if your 3715 can run 15.2, if not give 15.1 (4) Mx to try? HTH Herbert VPN IPSEC ASA with counterpart with dynamic IP and certificates Hello! Someone please give me config the work of the ASA for ASA Site to Site IPSEC VPN with counterpart with dynamic IP and authentication certificates. He works with PSK authentication. But the connection landed at DefaultRAGroup instead of DefaultL2LGroup with certificate authentication. Should what special config I ask a DefaultRAGroup to activate the connection? Thank you! In general I would suggest using option "cert." With nocheck, we are simply not strict on IKE ID matchin the certificate, which is normally not a problem of security :-) DMVPN with VRF (redistribution a road by default via VRF) Hi all I was testing a DMVPN configuration so that users with POLES surfing the Internet on the Internet portal of the HUB. The SPOKE1PN is able to ping all internal IP addresses and route determination agrees. When he reached out to the Internet (HUB_INTGW) gateway, pings are okay, but traceroute requests time out. I was wondering if anyone has an idea. Here's my topology. Basically, if SPOKE1PN pings to the Internet, it goes to SPOKE1, HUB1 via tu0, HUB1_INTGW and it gets overloaded NAT. QUESTION (OK, TRACEROUTE DROPS AFTER OVERLOADED NAT PINGS) SPOKE1PN #ping 202.0.0.2 rep 88 Type to abort escape sequence. 88, echoes ICMP 100 bytes to 202.0.0.2 sending, time-out is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!! Success rate is 100 per cent (88/88), round-trip min/avg/max = 144/211/328 ms SPOKE1PN #traceroute 202.0.0.2 Type to abort escape sequence. The route to 202.0.0.2 1 192.168.1.1 88 MS 64 ms 16 ms 2 172.14.1.1 164 MS 92 MS 128 ms 3 10.1.0.254 152 MS 124 MS ms 116 4 * * * 5 * * * 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * * SPOKE1 version 12.4 horodateurs service debug datetime msec Log service timestamps datetime msec no password encryption service ! hostname SPOKE1 ! boot-start-marker boot-end-marker ! ! No aaa new-model memory iomem size 5 IP cef ! IP vrf DMVPN RD 1:1 ! crypto ISAKMP policy 1 BA aes 256 md5 hash preshared authentication Group 5 address key crypto isakmp 0.0.0.0 @ngelam1chell3r1c 0.0.0.0 ISAKMP crypto keepalive 60 periodicals ! Crypto ipsec transform-set SET1 IPSEC ah-md5-hmac esp - aes ! Profile of crypto ipsec DMVPN game of transformation-IPSEC-SET1 ! interface Tunnel0 IP vrf forwarding DMVPN IP 172.14.1.2 255.255.255.0 no ip redirection IP mtu 1416 property intellectual PNDH authentication cisco123 property intellectual PNDH card 172.14.1.1 200.0.0.2 map of PNDH IP multicast 200.0.0.2 property intellectual PNDH card 172.14.1.254 200.0.1.2 map of PNDH IP multicast 200.0.1.2 PNDH id network IP-99 property intellectual PNDH nhs 172.14.1.1 property intellectual PNDH nhs 172.14.1.254 source of tunnel FastEthernet0/1 multipoint gre tunnel mode tunnel key 999 Protection ipsec DMVPN tunnel profile ! interface FastEthernet0/0 IP vrf forwarding DMVPN IP 192.168.1.1 255.255.255.0 automatic duplex automatic speed ! interface FastEthernet0/1 IP 201.0.0.2 255.255.255.240 Speed 100 full-duplex ! Router eigrp 1 Auto-resume ! address ipv4 vrf DMVPN family redistribute connected network 172.14.1.0 0.0.0.255 network 192.168.1.0 No Auto-resume autonomous system of-1 output-address-family ! IP forward-Protocol ND IP route 0.0.0.0 0.0.0.0 201.0.0.1 ! no ip address of the http server no ip http secure server ! control plan ! Line con 0 line to 0 line vty 0 4 ! end HUB1 version 12.4 horodateurs service debug datetime msec Log service timestamps datetime msec no password encryption service ! hostname HUB1 ! boot-start-marker boot-end-marker !
No aaa new-model memory iomem size 5 IP cef ! IP vrf DMVPN RD 1:1 ! crypto ISAKMP policy 1 BA aes 256 md5 hash preshared authentication Group 5 address key crypto isakmp 0.0.0.0 @ngelam1chell3r1c 0.0.0.0 ISAKMP crypto keepalive 60 ! Crypto ipsec transform-set SET1 IPSEC ah-md5-hmac esp - aes No encryption ipsec nat-transparency udp-program ! Profile of crypto ipsec DMVPN game of transformation-IPSEC-SET1 ! interface Tunnel0
IP vrf forwarding DMVPN IP 172.14.1.1 255.255.255.0 no ip redirection IP mtu 1416 property intellectual PNDH authentication cisco123 dynamic multicast of IP PNDH map PNDH id network IP-99 source of tunnel FastEthernet0/1 multipoint gre tunnel mode tunnel key 999 Protection ipsec DMVPN tunnel profile ! interface FastEthernet0/0 IP vrf forwarding DMVPN IP 10.1.0.1 255.255.255.0 automatic duplex automatic speed ! interface FastEthernet0/1 IP 200.0.0.2 255.255.255.240 Speed 100 full-duplex ! Router eigrp 1 Auto-resume ! address ipv4 vrf DMVPN family redistribute connected redistribute static Network 10.1.0.0 0.0.0.255 network 172.14.1.0 0.0.0.255 No Auto-resume autonomous system of-1 output-address-family ! IP forward-Protocol ND IP route 0.0.0.0 0.0.0.0 200.0.0.1 IP route vrf DMVPN 0.0.0.0 0.0.0.0 10.1.0.254 ! no ip address of the http server no ip http secure server ! control plan ! Line con 0 line to 0 line vty 0 4 ! end HUB1_INTGW version 12.4 horodateurs service debug datetime msec Log service timestamps datetime msec no password encryption service ! hostname HUB1_INTGW ! boot-start-marker boot-end-marker ! No aaa new-model memory iomem size 5 IP cef ! no ip domain search ! Authenticated MultiLink bundle-name Panel ! Archives The config log hidekeys ! interface FastEthernet0/0 IP 10.1.0.254 255.255.255.0 IP nat inside IP virtual-reassembly automatic duplex automatic speed ! interface FastEthernet0/1 IP 200.0.1.2 255.255.255.240 NAT outside IP IP virtual-reassembly Speed 100 full-duplex ! IP forward-Protocol ND IP route 0.0.0.0 0.0.0.0 200.0.1.1 IP route 192.168.1.0 255.255.255.0 10.1.0.1 ! no ip address of the http server no ip http secure server overload of IP nat inside source list ACL_NATOVERLOAD interface FastEthernet0/1 ! IP access-list standard ACL_NATOVERLOAD permit 10.1.0.0 0.0.0.255 permit 192.168.1.0 0.0.0.255 permit 172.14.1.0 0.0.0.255 ! control plan ! Line con 0 exec-timeout 0 0 Synchronous recording line to 0 line vty 0 4 ! end Desmon, If the works of ping I can bet you that it's a problem of how ICMP unreachable it will be via NAT (PAT in fact) in response to UDP with expired TTL. Can you do a static NAT on HUB1_INTGW to the IP test and you should see a difference... BTW the debug ip packet is your friend, try it :-) on INTGW and INT_RTR Marcin L2l between an ASA 5505 and WatchGuard XTM330 with dynamic IP Hi guys,. I looked for a solution on this one but can't find inappropriate, most of the discussions were old and with dead links to the solution. We have an ASA 5505 with static IP address on the outside and a customer who have a WatchGuard XTM330 with dynamic IP address to the outside. Is it possible to have an L2L VPN between our ASA and the WatchGuard when he has a dynamic IP? I have no experience on the series of WatchGuard, so, I am very grateful for any answer! Thanks in advance and have a nice day BR Robin Hi Robin, Here are the links you can make reference when configuring static to the dynamic VPN tunnel: -. This one is with Pix on the remote side, but the configuration will remain the same on the local side: -. Kind regards PS Please rate helpful messages. DMVPN with digital ceritificates and Hub acts as a CA server Hello guys,. is there anyway to configure the DMVPN with digital certificates and change the router Hub to act as a CA server? Thank you Yes, you can do it, go ahead and set up your router, Hub, with the normal DMVPN configuration so that it becomes the hub. After doing that follow the link below to add public key infrastructure server features: http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t4/feature/guide/gt_ioscs.html And to register for the rays on the hub, use this link: http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080210cdc.shtml Remember that regardless of the router Hub being the authority of CA, you must sign up for itself to allow the IKE PKI authentication. ASA - s2s vpn with dynamic ip - Dungeon tunnel upward Hi guys,. We want to set up a vpn between our central asa5520, and a new branch office asa5505 with dynamic public ip address. This type of configuration is supported, but the tunnel can only be initiated from the asa distance (the asa central do not know how to reach the asa remote). prove that on this vpn also transit traffic voice, we must always maintain the tunnel. A solution would be to have a kind of continuous ping from the remote office to the central office... is more 'professional' wat to reach our goal? Thank you. Try, 'management-access to the inside' of the asa and ping Materialized with dynamic input possible view? Hello We have some end users have a very complex query of SQL reports (~ 2500 lines) they came with. We are trying to tune and to create additional indexes as needed. He has made more than one aggregation of xml and the chain in select statements. in any case while I'm looking for other methods deal with the problem regardless of a potentially inefficient SQL query. In my opinion, they said that the query taking ~ 6000 sec to finish and basically http sessions expire of their web application after 4000 seconds of inactivity. They have a few dynamic user input from the web page which is fed in the request for multiple WHERE clauses. So I think we want to have this query that is run in offline mode (after the user input is collected) as well as the results stored in a table, then the wep app can do a simple select query to retrieve data from the table of results later. Is there a way to create a materialized view and replace user with some variables bind input and update the values of the variables bind with the participation of the user whenever they want the data, and then refresh the materialized view? Or if there is a better mechanism for Oracle to run asynchronously this query offline with dynamic input and then store the results in a table? My problem is that I don't know if they can call a sp and feed the bind values as parameters, but maybe I need to force them to. I really don't want to process SQL statements dynamic that their request is so great andt hey asked me on GTT, but I was under the impression that the data is lost after each session and probably wouldn't really solve anything. Thoughts? Oracle Database 11 g Enterprise Edition Release 11.2.0.4.0 - 64 bit Production Web pages should return something in<5s or="" the="" end-user="" will="" hit="" the="" refresh="" button="" again="" and="" again="" and="" again="" and="">5s> Do something like this: MK Train does not not as expected with dynamic regions JDeveloper version - 11.1.1.7.0 I created an application with 2 workflow with 3 defined fragments like a train. These workflows is deleted a page like dynamic regions. On the page running, in the first region the train works fine. But access to the second region, when I click on the 2nd train stop, the train navigates to the first fragment of the first step. Note: I also created a test application, it was the replication. I looked at your code and found the problem. The bean that you can switch regions is defined in the scope of evil. The TrainDynamicBean must be set in viewScope at least. If you set it in a scope less (backingBean or application) the bean is generated for each request. If you go to region 2 the bean is created again for the next request, and the taskflowid points again to flow available1. This is the reason why you see the view4 when you switch to flow2 but view5 clicking on flow available1. It is a problem.when known and documented, working with dynamic regions. JDev creates the bean in the wrong scope, and you have to take it at least viewScope. Timo TableView with dynamic and updatable columns Hello!! Im trying to encode a TableView with dynamic columns and I saw a lot of examples like this: create columns dynamically But none who would work for my needs. Its very simple: I got a list of customers, and each has a list of purchases. A purchase has a string "buyDetail" and a Date for the ship. My TableView need the first column with the name of the client, and a column more for each day of existing ships. We do not know previously days that will be used. If the sum is greater than 100, for example, I need to be able to apply different styles. Example: I can't use the properties because I don't know how to buy will have to each customer. My best test (only for the first column) was next, but I can't buy it updated if I change the value in the cell: I did not try to write other code columns because I feel that I don't hurt really... This shows the names of Customer´s, but I can't manage if data modification. Post edited by: user13425433 The columns are available already update default... If you happen to use JavaFX properties for the value of the source. The core of you're your question lies in your cellValueFactory. Here we have only the cellValueFactory for the name, not for the other columns. So I'll take the name for example, and you have to adapt to the other columns. But if you do something like this to your cellValueFactory: Then the name can never be updated if it modifies the client instance: there is no "link" between the name and the property used by the table.
We have therefore 3 test case: Then, if the name change pending Customer-> value in the table automatically changes.
It also works the other way around: If the table is editable, and the name property is not unalterable-> the value of the changes of names in the Customer instance follows the table has been changed. In this way, you have created a JavaFX property that is bound to an observable property Java Bean. Same as above, it works both ways when possible. Something like that: If you don't do something like that, the value of the table will never change when the name changes in the instance because the table does not change. Now, you will need to apply this theory to your price columns. I hope that I was clear enough to help you. SpeedGrade does not not with dynamic or stand-alone links. SpeedGrade does not not with dynamic or stand-alone links. Projevt cannot be bound, nor a project can be opened from scratch. Opening or creating a file isn't even an option, and I have a huge project to turn in tomorrow! WTH Adobe. I've updated the first CC 9.0.2 and still nothing Sorry for the correction, but Adobe (sometimes confusing) nomenclature, it's "Dynamic Link" to AfterEffects and 'Direct link' with SpeedGrade. I explained by engineers that they are two very different processes where the difference in name. My answer... If the processes are so very different, why are the names that could be confusing? "Because they are the more precise terminology of what happens." I think they are the most accurate to spoil the spirit of people, but I'm sure the engineers are smarter about this than me! The Direct link process ONLY works when he 'sees' appropriate corresponded builds... for the current coupled: CC2015.0.2/build 9.0.2(4) for first Pro; CC2015.0.1/build 9.0.1x21 for SpeedGrade Then... check your SpeedGrade (wrench, top tab of the 'About' page), making sure it is the correct version. Also... If there is a problem with is functional Sg (sometimes these programs need the Cleaner CC Adobe app to uninstall, then a new re - install) you can use the color workspace editing in Premiere Pro... He has a considerable amount of the capacity of the Sg, but not (for an experienced user of Sg) treat the whole meal. When even... you can make a good amount and quite quickly. And this gives you the expanses of SpeedGrade, that are better than the crappy things 'Fast' of this eons PrPro and '3 - Way' color Correctors use... yuck. Neil Need help with dynamic Action through 4 items Hello everyone. I'm having some trouble trying to comp with dynamic action that will turn on or display a select list item when a value is set for the four elements of the Radio button group. P1_SELCT_LIST P1_RADIO_GROUP_1 P1_RADIO_GROUP_2 P1_RADIO_GROUP_3 P1_RADIO_GROUP_4 So once all four Radio groups are not null, I want the select View list item. Any help with this would be great. I'm on Apex 4.2.0.00.27 Hello You can create the following action: Event: click on Selection type: jQuery selector jQuery selector: radio condition: $v ('P1_RADIO_GROUP_1')! == '' && $v ('P1_RADIO_GROUP_2')! == '' && $v ('P1_RADIO_GROUP_3')! == '' && $v ('P1_RADIO_GROUP_4')! == '' Then add a real Action as follows: ACtion: show Fires when the result of the event is: true Fire on the page loading: No. (uncheck) Assigned to elements, selection type: product (s) Product (s): P1_SELECT Also add an Action to false as follows: ACtion: hide Fires when the result of the event is: false Fire on the page loading: YES (check) Assigned to elements, selection type: product (s) Product (s): P1_SELECT Kind regards Vincent Performance issues with dynamic action (PL/SQL) Hello! I have 5 drop-down lists to select the columns that users want filter, 5 drop-down lists to select an operation and 5 boxes of input values. After that, it has a filter button that submits just the page based on the selected filters. This part works fine, the data are filtered almost instantly. After that, I have 3 selectors 3 boxes where users put the values they wish to update the filtered rows and column There is a update button that calls the dynamic action (a procedure which is written below). It should be in a straight line, the issue of performance might be the decoding section, because I need to cover the case when the user wants to set a null (@), and when it won't update the 3 columns, but less (he leaves "). That's why P99_X_UC1 | ' = decode(' ||) P99_X_UV1 |', "«,» | P99_X_UC1 ||',''@'',null,'|| P99_X_UV1 |') However, when I click finally on the button update, my browser freezes and nothing happens on the table. Can anyone help me solve this problem and improve the speed of the update? Kind regards Ivan PS The procedure code is below: create or replace DWP PROCEDURE. PROC_UPD (P99_X_UC1 in VARCHAR2, P99_X_UV1 in VARCHAR2, P99_X_UC2 in VARCHAR2, P99_X_UV2 in VARCHAR2, P99_X_UC3 in VARCHAR2, P99_X_UV3 in VARCHAR2, P99_X_COL in VARCHAR2, P99_X_O in VARCHAR2, P99_X_V in VARCHAR2, P99_X_COL2 in VARCHAR2, P99_X_O2 in VARCHAR2, P99_X_V2 in VARCHAR2, P99_X_COL3 in VARCHAR2, P99_X_O3 in VARCHAR2, P99_X_V3 in VARCHAR2, P99_X_COL4 in VARCHAR2, P99_X_O4 in VARCHAR2, P99_X_V4 in VARCHAR2, P99_X_COL5 in VARCHAR2, P99_X_O5 in VARCHAR2, P99_X_V5 in VARCHAR2, P99_X_CD in VARCHAR2, P99_X_VD in VARCHAR2 ) IS l_sql_stmt varchar2 (32600); nom_table_p varchar2 (30): = ' DWP. IZV_SLOG_DET'; BEGIN l_sql_stmt: = "update". nom_table_p | 'set '. || P99_X_UC1 | ' = decode(' ||) P99_X_UV1 |', "«,» | P99_X_UC1 ||',''@'',null,'|| P99_X_UV1 |'),' || P99_X_UC2 | ' = decode(' ||) P99_X_UV2 |', "«,» | P99_X_UC2 ||',''@'',null,'|| P99_X_UV2 |'),' || P99_X_UC3 | ' = decode(' ||) P99_X_UV3 |', "«,» | P99_X_UC3 ||',''@'',null,'|| P99_X_UV3 |') where ' | P99_X_COL | » '|| P99_X_O | » ' || P99_X_V | «and» | P99_X_COL2 | » '|| P99_X_O2 | » ' || P99_X_V2 | «and» | P99_X_COL3 | » '|| P99_X_O3 | » ' || P99_X_V3 | «and» | P99_X_COL4 | » '|| P99_X_O4 | » ' || P99_X_V4 | «and» | P99_X_COL5 | » '|| P99_X_O5 | » ' || P99_X_V5 | «and» | P99_X_CD | ' = ' || P99_X_VD; -dbms_output.put_line (l_sql_stmt); EXECUTE IMMEDIATE l_sql_stmt; END; Hello Ivan,. I don't think that the decoding is relevant performance. Perhaps the update is suspended because another transaction has changes that are uncommitted to any of the affected rows or where clause is not quite selective and has a huge amount of documents to update. In addition - and I may be wrong, because I only have a portion of your app - the code here looks like you've got a guy here huge sql injection vulnerability. Perhaps you should consider re - write your logic in the static sql. If this is not possible, you must make sure that the entered user contains only allowed values, for example by P99_X_On white list (i.e. to ensure that they contain only values known as 'is', ')<', ...),="" and="" by="" using="" dbms_assert.enquote_name/enquote_literal="" on="" the="" other="" p99_x_nnn="">',> Kind regards Christian Help with dynamic action and the selection list item Hi Carlos, I've set up a test case of exactly in the same way and it worked fine for me. I've created a page element called P1_DA_DEMO and added some values of the static selection list, then added a help text. I used the settings are lower, I suggest you try again, but also make sure that you have no other Javascript errors on the page. Use a tool like firebug to check. Name: Action Dynamics demo Real Actions Scope of the event set a Bind s. Thank you Paul AMPe ADF with Dynamic tab Shell not made in iPAD 1 +. Subba, I understand, however support for iPad added in PS5 is a set of new features, not a bug fix, so this cannot be claimed as a one off patch with the support of the Oracle. In this case that is expected to capture customers highlights new features of upgrade. Thank you Registration and getting started with the INK HP INSTANT Registration and getting started with ink HP Instant Note: your printer must be connected to the Internet via a wireless connection. How does that you will always have ink HP? Your printer uses Internet to let us know when to send more ink. Here's ho enclosure USB 2.0 for sata @ ide - recongnised but not available in xp I have a box of HD USB 2.0 to SATA @ IDE hard drive. I plug it into my computer and he recognizes her, but I can't display all the files contained in it because it is not in the files anywhere. I ran windows updates, but still do not see it.It is a x Cannot install windows update, error: 80004005 Original title: Update security for Windows Vista (KB978338) I have Windows Vista installed on Dell Inspiron 1420 laptop, which, as Ms security essential, installed, for the last 6 months, I get automatic updates automatically prompts for the securit WTR54GL v1.1 erratic led flashing sequence Sometimes, it's the ping requests sometimes here is an example Reply from 192.168.1.1: bytes = 32 time = 2ms TTL = 100Reply from 192.168.1.1: bytes = 32 time = 1ms TTL = 100Reply from 192.168.1.1: bytes = 32 time = 1ms TTL = 100Reply from 192.168.1.1 How to find which version of Windows Live Messenger I have no? whatversionofWindowsLiveMessengerdoIhave andwhydoIgetsomuchjunkmail?Similar Questions
The ASA uses parts of the client cert DN to perform a tunnel-group lookup to place the user in a group. When "peer-id-validate req" is defined the ASA also tries to compare the IKE ID (cert DN) with the actual cert DN (also received in IKE negotiation), if the comparison fails the connection fails. know you could set "peer-id-validate cert" for the time being and the ASA will try to compare the values but allow the connection if it cannot.
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-next-generation-firewalls/112075-dynamic-IPSec-ASA-router-CCP.html
http://www.WatchGuard.com/docs/4-6-Firebox-CiscoPix.PDF
Dinesh MoudgilCustomer 02/01/2015 03/01/2015 09/01/2015 Morgan $400 (buyDetail) 0 $100 Luis 0 0 $20 Steven $10 0 0 Hulk 0 $5 $32
table = new TableView<Customer>();
ObservableList<Customer> lista = FXCollections.observableList(registros);
table.setItems(lista);
TableColumn<Customer, Customer> customerNameColumn = new TableColumn<Customer, Customer>("");
customerNameColumn.setCellValueFactory(new Callback<CellDataFeatures<Customer, Customer>, ObservableValue<Customer>>() {
public ObservableValue<Customer> call(CellDataFeatures<Customer, Customer> p) {
return new SimpleObjectProperty(p.getValue());
}
});
customerNameColumn.setCellFactory(column -> {return new TableCell<Customer, Customer>() {
@Override
protected void updateItem(Customer item, boolean empty) {
super.updateItem(item, empty);
if (item == null || empty) {
} else {
setText(item.getName());
//APPLY STYLE
}
}
};
});
table.getColumns().addAll(customerNameColumn);
new SimpleObjectProperty(p.getValue().getName());
TableColumn
TableColumn
TableColumn
I have problems of perfomance with dynamic action that is triggered on click of a button.
I have problems trying to achieve to trigger the Help window from an element automatically select. A Help window is triggered when it is clicked on the label of an item, but my customer wants to be triguered automatically as soon as the user clicks to view the options in the select list.
I think I should be able to do with dynamic actions but I can't function.
I know when someone clicks on the label of the item selection list trigger this JavaScript
JavaScript:popupFieldHelp('277938589795252851','1545903379570909')
So I want to trigger the javascript also when the user click on the item selection list and pull down the options and for that I think that the dynamic action is the way to go, but I can't do things.
That's what I have to do:
I created a dynamic option as follows:
Name: test
Sequence: 30
Even: click
Selection type: product (s)
Article (s): P1_RATING <-a selection list item
Condtion: - no requirement.
Real Actions
Sequence: 10
Action: Run the JavaScript Code
Fires when the result of the event is: true
Fire on loading the page: checked
Code: javascript:popupFieldHelp('277938589795252851','1545903379570909')
Thank you anyone who can tell me what I'm doing wrong here or bring a solution to my problem to trigger the Help window from an element automatically select.
Kind regards
Carlos
Sequence: 10
Even: click
Selection type: product (s)
Product (s): P1_DA_DEMO<- a="" selection="" list="">->
Condtion: - no requirement.
Sequence: 10
Action: Run the JavaScript Code
Fires when the result of the event is: true
Fire on loading the page: unchecked
Code: javascript:popupFieldHelp('277938589795252851','1545903379570909')
We used the Oracle Dynamic tab Shell templates to build our page of dashboard with several dynamic tabs.
A year back when we have initially created the main dashboard with Dynamic tab Shell and used of the UIShell API to open new dynamic tab when clicking the command links in the browser side of left hand. We started with Jdev 11.1.1.3 and upgrade us until Jdev 11.1.1.5.
Now this last requirement is, we need to test our applications in the Safari browser in iPAD (2.0). During the test, we observed under questions.
(1) the page with Dynamic tab Shell JSPX is keep showing "Loading"... "We had updated the Safari browser twice to render the page.
(2) any af:commandLink under the JSPX which has shell model dynamic tab, does not. We have lots of links on the left navigation and when clicking on each link will open a new tab dynamic (we use UIShell API). Nothing happens when clicking on these af:commandLinks.
(3) we have 'Home' and 'Logout' links at the top right. Nothing happens on the links click too.
All these as af:commandLinks and af:commandButtons not working as expected when we have them beside a JSPX page without shell dynamic tab.
Tested and observed the same behavior both in version 1.0 and newer iPad iPAD 2.0.
We desperately need help on thin. Pls let us know, if I need to provide more details. Are there specific configurations required to make it work in Jdev 11.1.1.5? At this stage we cannot improve our Env 11.1.1.6 or 11.1.2 as we already have these applications in Production and we should give users flexibility to be used in the iPAD.
Help, please!
Thank you!!
Subba. Maybe you are looking for