DNS and routing

Similar Questions

• The fields 'Name' and 'Domain' to 'DNS and routing configuration/host Identification' are always in gray

  In VI3, I used to change the settings of the host DNS (host and domain name) to the tab 'DNS and routing' - & gt; "Identification of home." Even more, if the DNS and DHCP are configured correctly in the environment, there is no need to set these values manually - they were discovered automatically. The story is defferent in vSphere 4. I still have the set of fields 'Name' by 'localhost' and 'Domain' field is empty. And I can't change them - they are grey.

  Seems that the host is still able to discover its hostname automatically. I see the proper name in the (left pane of vSphere Client) console tree. But these values are not met the 'DNS and routing' tab and I can't put them manually.

  This is normal and how do I use these fields now?

  Yes, you're right. It's a little strange, but it works this way in vSphere now.

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru

• Laptops acquire wrong address DHCP, DNS and gateway wireless

  I have problems with two laptops. For some strange both acquire the bad DHCP, DNS and gateway (server) respond when I try to access the Internet via Wi - Fi. For some reason, this does not happen when I use the LAN (cable) connection.

  that is instead to fetch the address: 133.24.56.78 (no real address), the system retrieves / uses 111.22.33.44 (again, not a real address). BTW, these two systems are configured to fetch automatically get IP addresses and DHCP. I tried to fix the connection in both cases, but it did not work.

  What can I do to fix this?

  Problem solved.

  I changed the router to WEP (WPA - PSK) encryption.

• LAN to lan vpn between ASA and router 7200

  Hi friends,

  I need to configure the lan to lan between ASA vpn (remote location) and router 7200 (on our network).

  <7200 router="" (ip="" add:="" 10.10.5.2)="">-(Internet) -<(IP add:="" 192.168.12.2)="" asa(5510)="">---192.135.5.0/24 network

  I will have the following configuration:

  7200 router:

  crypto ISAKMP policy 80

  the enc

  AUTH pre-shared

  Group 1

  life 3600

  ISAKMP crypto key cisco123 address 192.168.12.2

  Cryto ipsec transform-set esp - esp-md5-hmac VPNtrans

  map VPNTunnel 80 ipsec-isakmp crypto

  defined by peer 192.168.12.2

  game of transformation-VPNtrans

  match address 110

  int fa0/0

  IP add 10.10.5.2 255.255.255.192

  IP virtual-reassembly

  no ip route cache

  Speed 100

  full duplex

  card crypto VPNTunnel

  access-list 110 permit ip any 192.135.5.0 0.0.0.255

  ASA:

  int e0/0

  nameif inside

  security-level 100

  192.135.5.254 Add IP 255.255.255.0

  int e0/1

  nameif outside

  security-level 0

  IP add 192.168.12.2 255.255.255.240

  access-list ACL extended ip 192.135.5.0 allow 255.255.255.0 any

  Route outside 0.0.0.0 0.0.0.0.0 192.168.12.3 1

  "pre-shared key auth" ISAKMP policy 10

  ISAKMP policy 10-enc

  ISAKMP policy 10 md5 hash

  10 1 ISAKMP policy group

  ISAKMP duration strategy of life 10-3600

  Crypto ipsec transform-set esp - esp-md5-hmac VPNtran

  card crypto VPN 10 matches the ACL address

  card crypto VPN 10 set peer 10.10.5.2

  card crypto VPN 10 the transform-set VPNtran value

  tunnel-group 10.10.5.2 type ipsec-l2l

  IPSec-attributes of type tunnel-group 10.10.5.2

  cisco123 pre-shared key

  card crypto VPN outside interface

  ISAKMP allows outside

  dhcpd address 192.135.5.1 - 192.135.5.250 inside

  dhcpd dns 172.15.4.5 172.15.4.6

  dhcpd wins 172.15.76.5 172.15.74.5

  dhcpd lease 14400

  dhcpd ping_timeout 500

  dhcpd allow inside

  Please check the configuration, please correct me if I missed something. I'm in a critical situation at the moment...

  Please advise...

  Thank you very much...

  Where it fails at the present time?

  Can you share out of after trying to establish the VPN tunnel:

  See the isa scream his

  See the ipsec scream his

  Please also run the following debug to see where it is a failure:

  debugging cry isa

  debugging ipsec cry

• Client certificate and router WebVPN

  Hello!

  In my test harness I can not to run my webvpn configuration =.

  I have several components: AD MS, MS CS (but without NDE), 2911 router and client computer. Client and router have a certificate of MS CS. In my setup I use certificate or aaa (LDAP) authentication and authentication work aaa good. But the client certificate authentication does not work. And my internal https services do not work too--"no certificate or invalid", but this strange because I imported the CA certificate for that.

  Can you help me it work?

  My version of 2911:

  Cisco IOS software, software C2900 (C2900-UNIVERSALK9-M), Version 15.1 (3) T, RELEASE SOFTWARE (fc1)

  My Config:

  AAA authentication login webvpn group local ldap

  IP local pool webvpn 192.168.200.1 192.168.200.254

  bind authenticates root-dn cn = webvpn, OU = team, dc = domain, dc = com password [email protected]/ * /.

  WebVPN vpn gateway

  IP address port 4443

  SSL root-ca trustpoint

  development

  !

  WebVPN install svc flash0:/webvpn/anyconnect-dart-win-2.5.3055-k9.pkg sequence 1

  !

  employee framework WebVPN

  SSL authentication check all

  !

  connection message 'Portal VPN'

  !

  the policy group peche1

  List of URLS "on the inside".

  functions compatible svc

  filter VPN SPLIT tunnel

  SVC-pool of addresses "webvpn" netmask 255.255.255.0

  SVC by default-domain "domain.com".

  SVC Dungeon-client-installed

  SVC split dns "domain.com".

  SVC split include 192.168.0.0 255.255.0.0

  SVC-Server primary dns 192.168.1.1

  SVC-Server secondary dns 192.168.1.2

  Citrix enabled

  virtual-model 1

  strategy-group-by default peche1

  AAA authentication list webvpn

  vpn gateway

  authentication certificate

  user name - sign up

  root CA trustpoint-AC

  User location flash0 profile: / userprof

  development

  !

  Crypto pki trustpoint root-ca

  Terminal registration

  revocation checking no

  rsakeypair root-ca

  !

  I imported with CA pkcs12 certificate.

  My debug (it happened so I am trying to access my webvpn portal and I choose my certificate of MS CS for access)

  5 Jun 11:22:39: WV: validated_tp: cert_username: matched_ctx:

  5 Jun 11:22:39: WV: could not get opssl appinfo sslvpn

  5 Jun 11:22:39: WV: could not get opssl appinfo sslvpn

  5 Jun 11:22:39: WV: error: no certificate validated for the customer

  Can someone explain to me why it does not work?

  Resolved by the update IOS - version 15.2 (4) M2.

  Concerning

• my browser cannot open google and facebook and other https sites that it does not open even the app store does not work, I tried to change my DNS google DNS and disable IPv6 but still no use, help PLZ!

  my browser cannot open google and facebook and other https sites that it does not open even the app store does not work, I tried to change my DNS google DNS and disable IPv6 but still no use, help PLZ!

  You may have installed one or more variants of the malware "VSearch' ad-injection. Please back up all data, and then take the steps below to disable it.

  Do not use any type of product, "anti-virus" or "anti-malware" on a Mac. It is never necessary for her, and relying on it for protection makes you more vulnerable to attacks, not less.

  Malware is constantly evolving to work around defenses against it. This procedure works now, I know. It will not work in the future. Anyone finding this comment a couple of days or more after it was published should look for a more recent discussion, or start a new one.

  Step 1

  VSearch malware tries to hide by varying names of the files it installs. It regenerates itself also if you try to remove it when it is run. To remove it, you must first start in safe mode temporarily disable the malware.

  Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. Ask for other instructions.

  Step 2

  When running in safe mode, load the web page and then triple - click on the line below to select. Copy the text to the Clipboard by pressing Control-C key combination:

  /Library/LaunchDaemons

  In the Finder, select

  Go ▹ go to the folder...

  from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

  A folder named "LaunchDaemons" can open. If this is the case, press the combination of keys command-2 to select the display of the list, if it is not already selected.

  There should be a column in the update Finder window. Click this title two times to sort the content by date with the most recent at the top. Please don't skip this step. Files that belong to an instance of VSearch will have the same date of change for a few minutes, then they will be grouped together when you sort the folder this way, which makes them easy to identify.

  Step 3

  In the LaunchDaemons folder, there may be one or more files with the name of this form:

  com Apple.something.plist

  When something is a random string, without the letters, different in each case.

  Note that the name consists of four words separated by dots. Typical examples are:

  com Apple.builins.plist

  com Apple.cereng.plist

  com Apple.nysgar.plist

  There may be one or more items with a name of the form:

  com.something.plist

  Yet once something is a random string, without meaning - not necessarily the same as that which appears in one of the other file names.

  These names consist of three words separated by dots. Typical examples are:

  com.semifasciaUpd.plist

  com.ubuiling.plist

  Sometimes there are items (usually not more than one) with the name of this form:

  com.something .net - preferences.plist

  This name consists of four words (the third hyphen) separated by periods. Typical example:

  com.jangly .net - preferences.plist

  Drag all items in the basket. You may be prompted for administrator login password.

  Restart the computer and empty the trash.

  Examples of legitimate files located in the same folder:

  com.apple.FinalCutServer.fcsvr_ldsd.plist

  com Apple.Installer.osmessagetracing.plist

  com Apple.Qmaster.qmasterd.plist

  com Apple.aelwriter.plist

  com Apple.SERVERD.plist

  com Tether.plist

  The first three are clearly not VSearch files because the names do not match the above models. The last three are not easy to distinguish by the name alone, but the modification date will be earlier than the date at which VSearch has been installed, perhaps several years. None of these files will be present in most installations of Mac OS X.

  Do not delete the folder 'LaunchDaemons' or anything else inside, unless you know you have another type of unwanted software and more VSearch. The file is a normal part of Mac OS X. The "demon" refers to a program that starts automatically. This is not inherently bad, but the mechanism is sometimes exploited by hackers for malicious software.

  If you are not sure whether a file is part of the malware, order the contents of the folder by date modified I wrote in step 2, no name. Malicious files will be grouped together. There could be more than one such group, if you attacked more than once. A file dated far in the past is not part of the malware. A folder in date dated Middle an obviously malicious cluster is almost certainly too malicious.

  If the files come back after you remove the, they are replaced by others with similar names, then either you didn't start in safe mode or you do not have all the. Return to step 1 and try again.

  Step 4

  Reset the home page in each of your browsers, if it has been modified. In Safari, first load the desired home page, then select

  ▹ Safari preferences... ▹ General

  and click on

  Set on the current Page

  If you use Firefox or Chrome web browser, remove the extensions or add-ons that you don't know that you need. When in doubt, remove all of them.

  The malware is now permanently inactivated, as long as you reinstall it never. A few small files will be left behind, but they have no effect, and trying to find all them is more trouble that it's worth.

  Step 5

  The malware lets the web proxy discovery in the network settings. If you know that the setting was already enabled for a reason, skip this step. Otherwise, you should undo the change.

  Open the network pane in system preferences. If there is a padlock icon in the lower left corner of the window, click it and authenticate to unlock the settings. Click the Advanced button, and then select Proxies in the sheet that drops down. Uncheck that Auto Discovery Proxy if it is checked. Click OK, and then apply.

  Step 6

  This step is optional. Open the users and groups in the system preferences and click on the lock icon to unlock the settings. In the list of users, there may be some with random names that have been added by the malware. You can remove these users. If you are not sure whether a user is legitimate, do not delete it.

• Requirement of DNS and DHCP Server Essentials 2012 home

  I have a Server Windows Essentials 2012 acting as DNS and DHCP server with a domain name for backups etc on my home network. It's that everything works fine, no errors, no problem. Works well actually, telling me when the children did not install updates or restarted.

  I have two groups of users. My sons step, 10 and 12, which I want to use OpenDNS as a provider external DNS with a policy very, very limited and my wife and me who want to use indications of root or Google DNS or any other DNS provider. Others, specific devices no user (box of the xBox, WII, Satellite, TV, CCTV etc.) can use.

  Before the 2012 server, I had a 2 k 3 server running in a virtual machine for DHCP, alone and put my wife and my devices on static reservations with the just and external DNS provider used OpenDNS as the default scope, DNS. Unfortunately different bits of domain services 2012 don't seem to work unless the server of 2012 is the first DNS server listed on client machines (backups failed. Impossible to find other local computers). Currently, this means that we are all using OpenDNS.

  What I would like is a way to say 2012 to send adult group DNS queries to another DNS provider and leave the rest at default to OpenDNS, while still having them register in the original DNS domain. Any suggestions?

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Wireless connection unavailable on laptop, but shows all ok on pc and router

  I was at Midway through a conversation today on msn when my wireless connection (on my laptop) disappeared. I checked my pc and everything seems ok, here, my netgear router shows that everything is fine. When I click on 'Find a wireless network' his party! I can access the net very well by plugging it but as soon as I go wireless, I still lost.

  Tried to connect manually - says network with that name already there
  Tried to re start all
  All cables checked

  It's a laptop Toshiba L300
  Virgin cable broadband
  Router NETGEAR Wireless

  everything works fine as long as I'm using the cables.

  I only had my laptop and router wireless for a month.

  Please any other ideas what to do, I really need to be wireless for work as soon as possible

  Hello severina_falls,

  Thanks for posting on the Microsoft answers Community Forum.

  I have some suggestions for you to see if we can provide you with your wireless connection.

  (1) check that the WiFi switch is on on the front panel of your laptop. It is a quick check
  (2) Recycle the router wireless on and outside. Wait at least one minute, then turn it back on. Retest with your wireless network.
  (3) are getting you the error messages in the case where connects to deal with your wireless connection?
  To join the event logs: click on the Start button, right-click computer, click on manage.
  If you receive a notification of user account control , simply click on continue.
  Double-click Event Viewer. Study summary of the the event logs for errors dealing with wireless.
  (4) use System Restore to get your iIf wireless upward and running, you have a System Restore Point that was before starting the problem with your wireless network.
  Use the following KB to get the procedure on the system restore.
  936212 KB - how to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows Vista
  http://support.Microsoft.com/kb/936212

  If please post again and let us know if it helped to solve your problem or if you need further assistance.

  Sincerely, Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Site to Site between ASA VPN connection and router 2800

  I'm trying to get a L2L VPN working between a ASA code 8.4 and a 2800 on 12.4.

  I first saw the following errors in the debug logs on the side of the ASA:

  Error message % PIX | ASA-6-713219: KEY-GAIN message queues to deal with when
  ITS P1 is complete.

  I see the following on the end of 2800:

  ISAKMP: (0): treatment charge useful vendor id
  ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 157
  ISAKMP: (0): provider ID is NAT - T v3
  ISAKMP: (0): treatment charge useful vendor id
  ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69
  ISAKMP (0): provider ID is NAT - T RFC 3947
  ISAKMP: (0): treatment charge useful vendor id
  ISAKMP: (0): treatment of frag vendor id IKE payload
  ISAKMP: (0): IKE Fragmentation support not enabled
  ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
  ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM1

  ISAKMP: (0): built NAT - T of the seller-rfc3947 ID
  ISAKMP: (0): send package to x.x.x.x my_port 500 peer_po0 (R) MM_SA_SETUP
  ISAKMP: (0): sending a packet IPv4 IKE.
  ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
  ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM2

  ISAKMP (0): packet received from x.x.x.x dport 500 sports global (R)

  MM_SA_SETUP
  ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
  ISAKMP: (0): former State = new State IKE_R_MM2 = IKE_R_MM3

  ISAKMP: (0): processing KE payload. Message ID = 0
  ISAKMP: (0): processing NONCE payload. Message ID = 0
  ISAKMP: (0): found peer pre-shared key x.x.x.x corresponding
  ISAKMP: (2345): treatment charge useful vendor id
  ISAKMP: (2345): provider ID is the unit
  ISAKMP: (2345): treatment charge useful vendor id
  ISAKMP: (2345): provider ID seems the unit/DPD but major incompatibility of 54
  ISAKMP: (2345): provider ID is XAUTH
  ISAKMP: (2345): treatment charge useful vendor id
  ISAKMP: (2345): addressing another box of IOS!
  ISAKMP: (2345): treatment charge useful vendor id
  ISAKMP: (2345): vendor ID seems the unit/DPD but hash mismatch
  ISAKMP: receives the payload type 20
  ISAKMP (2345): sound not hash no match - this node outside NAT
  ISAKMP: receives the payload type 20
  ISAKMP (2345): no NAT found for oneself or peer
  ISAKMP: (2345): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
  ISAKMP: (2345): former State = new State IKE_R_MM3 = IKE_R_MM3

  ISAKMP: (2345): sending package x.x.x.x my_port Exchange 500 500 (R)

  MM_KEY_EXCH

  ----------

  This is part of the configuration of the ASA:

  network of the ABCD object
  10.20.30.0 subnet 255.255.255.0
   
  network of the ABCD-Net object
  172.16.10.0 subnet 255.255.255.0
   
  cry-map-77-ip object-group XXXX object abc-site_Network allowed extended access list
   
  access list abc-site extended permitted ip object-group XXXX object abc-site_Network
   
  ip access list of abc-site allowed extended object abc-site_Network object-group XXXX-60
   
  NAT (any, any) static source 20 XXXX XXXX-20 destination static abc-site_Network abc-site_Network
   
  NAT (any, any) static source 20 XXXX XXXX-20 destination static abc-site_Network abc-site_Network
   
  XXXX-20
   
  object-group network XXXX-20
  ABCD-Net network object
  object-abcd-Int-Net Group
   
  XXXX_127
   
  object-group network XXXX-20
  ABCD-Net network object
  object-abcd-Int-Net Group
   
  ip access list of abc-site allowed extended object abc-site_Network object-group XXXX-60
   
   
  Crypto card off-map-44 11 match address cry-map-77
  card crypto out-map-44 11 counterpart set 62.73.52.xxx
  card crypto out-map-44 11 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  cry-map-77-ip object-group XXXX object abc-site_Network allowed extended access list

  Crypto card off-map-44 11 match address cry-map-77
  card crypto out-map-44 11 counterpart set 62.73.52.xxx
  card crypto out-map-44 11 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  card crypto out-map-44 11 set transform-set ESP-3DES-SHA ikev1

  object-group network XXXX
  ABCD-Net network object
  object-abcd-Int-Net Group

  ------------------------

  Here is a part of the 2800:

  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  ISAKMP crypto key r2374923 address 72.15.21.xxx
  !
  !
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  !
  card crypto cry-map-1 1 ipsec-isakmp
  the value of 72.15.21.xxx peer
  game of transformation-ESP-3DES-SHA
  match address VPN
  !
  type of class-card inspect match class-map-vpn
  game group-access 100
  type of class-card inspect cm-inspect-1 correspondence
  group-access name inside-out game
  type of class-card inspect correspondence cm-inspect-2
  match the name of group-access outside
  !
  !
  type of policy-card inspect policy-map-inspect
  class type inspect cm-inspect-1
  inspect
  class class by default
  drop
   
  type of policy-card inspect policy-map-inspect-2
  class type inspect class-map-vpn
  inspect
  class type inspect cm-inspect-2
  class class by default
  drop
  !

  !
  interface FastEthernet0
  IP address 74.25.89.xxx 255.255.255.252
  NAT outside IP
  IP virtual-reassembly
  security of the outside Member area
  automatic duplex
  automatic speed
  crypto cry-card-1 card
  !
  interface FastEthernet1
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  IP nat inside source overload map route route-map-1 interface FastEthernet0
  !
  IP access-list extended inside-out
  IP 172.16.10.0 allow 0.0.0.255 any
  IP nat - acl extended access list
  deny ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
  deny ip 10.200.0.0 0.0.255.255 172.16.10.0 0.0.0.255
  deny ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
  deny ip 0.0.255.255 28.20.14.xxx.0.0 172.16.10.0 0.0.0.255
  refuse the 10.10.10.0 ip 0.0.0.255 172.16.10.0 0.0.0.255
  refuse the 172.16.10.0 ip 0.0.0.255 192.168.0.0 0.0.255.255
  refuse the 172.16.10.0 ip 0.0.0.255 10.200.0.0 0.0.255.255
  refuse the 172.16.10.0 ip 0.0.0.255 192.168.0.0 0.0.255.255
  refuse the 172.16.10.0 ip 0.0.0.255 28.20.14.xxx.0.0 0.0.255.255
  refuse the 172.16.10.0 ip 0.0.0.255 10.10.10.0 0.0.0.255
  allow an ip
  outside extended IP access list
  allow an ip
  list of IP - VPN access scope
  IP 172.16.10.0 allow 0.0.0.255 192.168.0.0 0.0.255.255
  IP 172.16.10.0 allow 0.0.0.255 10.200.0.0 0.0.255.255
  IP 172.16.10.0 allow 0.0.0.255 192.168.0.0 0.0.255.255
  IP 172.16.10.0 allow 0.0.0.255 28.20.14.xxx.0.0 0.0.255.255
  IP 172.16.10.0 allow 0.0.0.255 10.10.10.0 0.0.0.255
  IP 192.168.0.0 allow 0.0.255.255 172.16.10.0 0.0.0.255
  IP 10.200.0.0 allow 0.0.255.255 172.16.10.0 0.0.0.255
  IP 192.168.0.0 allow 0.0.255.255 172.16.10.0 0.0.0.255
  28.20.14.xxx.0.0 0.0.255.255 ip permit 172.16.10.0 0.0.0.255
  ip licensing 10.10.10.0 0.0.0.255 172.16.10.0 0.0.0.255

  access-list 23 allow 192.168.0.0 0.0.255.255
  access-list 23 allow 10.200.0.0 0.0.255.255
  access-list 23 allow 172.16.10.0 0.0.0.255
  access-list 123 note category class-map-LCA-4 = 0
  access-list 123 allow ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
  access-list 123 allow ip 10.200.0.0 0.0.255.255 172.16.10.0 0.0.0.255
  access-list 123 allow ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
  access-list 123 allow ip 0.0.255.255 28.20.14.xxx.0.0 172.16.10.0 0.0.0.255
  access-list 123 allow ip 10.10.10.0 0.0.0.255 172.16.10.0 0.0.0.255
  access-list 123 allow ip 172.16.10.0 0.0.0.255 192.168.0.0 0.0.255.255
  access-list 123 allow ip 172.16.10.0 0.0.0.255 10.200.0.0 0.0.255.255
  access-list 123 allow ip 172.16.10.0 0.0.0.255 192.168.0.0 0.0.255.255
  access-list 123 allow ip 172.16.10.0 0.0.0.255 28.20.14.xxx.0.0 0.0.255.255
  access-list 123 allow ip 172.16.10.0 0.0.0.255 10.10.10.0 0.0.0.255
  !
  !
  !

  !
  route-map-1 allowed route map 1
  match the IP nat - acl
  !

  Hello

  I quickly browsed your config and I could notice is

  your game of transformation (iskamp) on SAA and router are not the same, try to configure the same on both sides.

  in the statement of the ASA NAT you gave (any, any) try to give the name of the interface instead of a whole.

• DNS and static translations

  I have a web server on my dmz. On the demilitarized zone, the computers cannot be accessed by name. The problem is that DNS returns the ip (real) outside. I need the demilitarized zone to translate it into a local ip address. I use the MDP so I'm not using aliases. Any help would be appreciated.

  You can do this with the [static] commands and the "dns" option

  static (dmz, outside) 123.123.123.123 192.168.1.1 dns netmask 255.255.255.255 [keyword dns tells the pix to DNS doctoring for this translation because DNS resolves the public IP address]

  static (dmz, inside) 123.123.123.123 192.168.1.1 subnet 255.255.255.255 mask [allows the internal hosts to connect to the public IP found in DNS and it translates the private IP on the way to the demilitarized zone]

  Make sure you do a [clear xlate] after the changes.

  If you are running under 6.2, you will have to make any [alias] on the Pix.

• Private of IPSec VPN-private network between ASA and router

  Hello community,

  This is first time for me to configure IPSec VPN between ASA and router. I have an ASA 5540 at Headquarters and 877 router to EH Branch

  Headquarters ASA summary.

  Peer IP: 111.111.111.111

  Local network: 10.0.0.0

  Branch

  Peer IP: 123.123.123.123

  LAN: 192.168.1.0/24

  Please can someone help me set up the vpn.

  Hello

  This guide covers exactly what you need:

  Establishment of ASDM and SDM - http://www.netcraftsmen.net/resources/archived-articles/273.html

  Tunnel VPN - ASA to the router configuration:

  http://www.Cisco.com/en/us/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml#ASDM

  Kind regards

  Jimmy

• Issue of ASA NAT and routing

  Hello

  I have a question about NAT and routing on the SAA. I'm relatively new to ASA and don't know if it works or not. I have a pool of public IP (209.x.x.x/28) that routes my ISP to the external interface of my ASA. IP was assigned address for the outside of the ASA is an address of 206.x.x.2/24 with a default GW of 206.x.x.1. I intend using NAT to allow my web/mail servers on the DMZ (192.168.x.x) use 209.x.x.x addresses. However, I do know how to make it work since I'm not arping on any interface for 209.x.x.x addresses as they will be sent to the 206.x.x.2 address by the ISP. Can I just set up a translation NAT (on the external interface?) of the 209.x.x.x on 192.168.x.x address and the ASA will figure it out?

  Thanks for the help.

  Todd

  The ASa will figure it out, he will answer ARP queries for all that he has set up in a "static" command As long as th PSIA routes 209.x.x.x directly to the ASA addresses then it should all work fine.

  You just need to add lines like the following:

  static (dmz, external) 209.x.x.x netmask 255.255.255.255 192.168.x.x

  for each of your internal servers in the DMZ. Then an access-list to allow only HTTP/SMTP/etc through these addresses 209.x.x.x.

  list of allowed inbound tcp access any host 209.x.x.x eq smtp

  list of allowed inbound tcp access any host 209.y.y.y eq http

  Access-group interface incoming outside

• How to start Alerts notification to visitors using the DNS and IP society?

  1. I need to configure alerts for notification of visitor using the society of DNS and IP? How to do this?

  2 - second thing is what is the common use of DNS and IP society in the fields of account?

  Thank you

  Nabila,

  It is largely something E9 - the notification feature a much simpler with Profiler (Yes, there is a separate fee)

  without prospect Profiler: (I think I have the actual documentation at my office - will check once I'm back from #mme15 )

  1. go to settings, profiles of visitors, then change your display to show the fields you want to see.  Since you ask specifically about DNS and IP address, the view of the "technical information" is a good starting point.

  

  2. go into Setup and default user settings for users, configurations of Notification to visitors.  You can use the default or create new (lower right corner)

  Specify the view you want to use.  You can also create a custom for this notification by electronic mail header.

  3. go to settings, Notifications

  

  Configure your notification rules.

  

  for your second question - common use of DNS and IP name in the account fields, I don't think that there is a "common use" since the visitor record will show exactly the IP address and most organizations have a range of IP addresses, any sort of comparison of the visitor to the account is difficult.

  If your use case must match their account of visitors, e-mail domain is much easier.  Create a field on the Contact and account for the 'area of email address', a string manipulation cloud app to take the email address and delete everything before him ' @' accounts will be filled with the domain via a data load (or you can approach with a rule/validation rule set update to the name of the company (, remove the spaces and special characters and add with ".com")

  You could then: linking contacts to accounts using this field (will need to ensure that duplicate any record company) or use a rule of Match/deduplication to enter the values for the table of the company to update the contact. (or vice versa)

  I hope this helps.

  Nathan

• A stumper! Help! 5 Buck to the solution! 2 AP bridge mode and router to the internet

  Here's my setup. Draw yourself a diagram please

  I have a model axis video camera server box 2401 connected with RJ45 to a Linksys WAP54G AP in the barn.

  The WAP54G barn then bridge to an another WAP54G wireless in the House.  The WAP54G home is in AP mode. The WAP54G barn is in bridge mode.  MAC addresses are entered correctly in each.  Same channel, no encryption.

  The WAP54g barn is 192.168.1.57 static

  The WAP54G home is 192.168.1.244 static

  The WAP54G home is then RJ45 connected to the RTP300 master of LInkysys wireless router

  Well, I figgured it myself late last night

  I made some changes on the server AXIS... and to the LInksys router

  • Server DNS changed on the axis to match the IP address of the router is 255.255.255.0 192.168.1.1 now
  • change the front entrance of the port on the router to TCP only

  don't know who fixed it but it woks on the internet

  BTW once I have the port forward to the internet, the server can be seen on the internal IP address

  Thank you to those who answered... I wil favorite these links in the case where I need for future use

  appleo

• Problems with new cable modem and router

  Long story short, that my cable modem went bad.  I replaced it.  Now the two computers cannot connect to the internet.  It gives me a DNS error, saying that they can not find the server.  However, I can get on the internet if I hang the right modem to computer with courses through the router. I got it with the new modem a few days of work and use of the router, but now it does not work.

  There are 2 computers on the network, the two runnning vista.
  a linksys router model number BEFW11S4 ver 4.
  and the motorola surfboard SB5101 modem.  the old modem was a surfboard SB5100 motorcycle.

  There's a btn reset on the router (often the metal clip through a pin hole)
  Everything also its possible allways the router is bad