Does not start a new Section on a left-hand page

Similar Questions

• I installed the new version of LIghtroom (2015) compared to the creative clouds.  Creative cloud said that I installed the new version.  However, the shortcut icon that has been installed does not start the new version.  Also, I went to the link propertie

  I installed the new version of LIghtroom (2015) compared to the creative clouds.  Creative cloud said that I installed the new version.  However, the shortcut icon that has been installed does not start the new version.  I also went on the link properties itself, but without success in starting.  How to launch the new version?

  Thank you, toinimj59.  I did this part and the installation is complete (there is apparently not earlier--included an acceptance of the general terms and conditions...)

  Solution 1: Disconnect from the desktop creative cloud app and reconnect

  1. Disconnect from and to, the app Office creative Cloud click here for instructions to return in
  2. Launch of Lightroom.

• Does not start a new library.

  Just LightRoom will not start a new library.

  Now what of importance.  It does not start a new library.

  ???

  John

  John,

  You have not given nearly enough information to be able to answer your question.

  What OS are you on? That's what you try to do? How are you trying to do? (In detail).

  And finally, tell us exactly what is happening. Cite error messages in its entirety.

  HAL

• XPS 9000 froze and restart does not start - get the cursor flashing, top left of the screen

  System was working normally and after some time froze - no mouse movement, clock does not move, etc.

  Did a stop down with the power button (hold down 10 sec +) to stop.

  On switching on, does not pass through the boot sequence.  F2 does nothing and the only sigh of 'life' is a blinking cursor, upper left corner of the screen.  Tried to close - turn several times with the same result.

  I suspect a motherboard problem because there is no start. Don't know any other tricks to try to resuscitate the box.

  Does anyone have experience/solution for this type of problem?

  WGR,

  As there is no "beeps", I guess as a failed motherboard.

  Try the following, if you are comfortable working around computers:

  Note: The only 100% POWER supply test method, is to install a known working power.
  
  Unplug the power cord, hold the power button in for about 15-20 seconds, open the case, disconnect the power connector 24-pin motherboard and jumping the Green wire to one of the black wires, plug in the power cord and the power of the system, if food and case fans and disk hard drive performance then the power supply should be good.

  Note: Do not remove the wires from the plug, use a small piece of wire or a paper clip as a rider.

  Excerpt from power supply, again, unplug the power cord, hold the power button again for 15/20 seconds to discharge residual power, reconnect the connector 24 pin to the motherboard.
  Remove all the computer PCI cards, remove the video card [as appropriate], disconnect all devices, except the monitor, mouse and keyboard and unplug cable power & data of all readers.
     
  Reconnect the power cord and power the system on, see if you get something different from the LED on the power button, or any 'beeps '.

  No difference, remove the system memory and try again.

  Still shows no signs of life while looking at a motherboard replacement & maybe a processor.

  Note: The good news is, processors lack rarely, being the only method I know to check a processor, install a compatible work PC, or use a known job processing.

  Unfortunately the Dell OEM XPS 9000 renovated/new motherboards are not cheap.
       
  Bev.

• Tecra S5 does not start on new battery

  Hello
  I recently bought a new battery for my Tecra (the original one has been able to the laptop for less than 10 minutes).
  When I put the new battery (which is fully charged) in my laptop and try to feed upward, the system hangs with a black screen
  and the text cursor blinking "_" in the upper left corner, before windows xp starts.
  It happens with or without AC adapter plugged.
  If I replace the new battery with the old, or remove and boot on power AC/DC, the system starts properly.
  If I boot on current alternative and insert the new battery and unplug the power, I can work until the next boot - so it seems that
  the new battery is OK.
  the new battery is not true toshiba but WhiteEnergy. I used the mark with my previous satellite and worked well.
  Do you have anny suggestions or to change settings?
  The symptoms are quite weired to me.

  > Symptoms are quite weired to me.
  For me, too. Settings to change? I put t really know what kind of settings can improve this.
  When you start your laptop on battery only, you can enter the BIOS settings?
  Have you tried to set on the default settings and check if something will change?

• HotSync does not start with new Tungsten E2

  I put my old camera Tungsten T2 with an E2 level.  Following the upgrade instructions, I implemented the E2 last night and let it charge all night, then tonight made a final with the T2 HotSync and run the installation program on the CD supplied with the E2.  At the time when the installer asks me to press the HotSync button on the USB cable I did and Windows came the notice in the system tray as a new USB device and the Palm handheld device was ready to use.  After that, nothing.  A minute or two later the E2 expires and he said that "the connection between your device and the desktop could not be established.  Please check your configuration and try again. »

  I tried to reinstall the software, upgrade to Palm Desktop 6.2 from the web site, and then restarting the computer several times, but I can never get the HotSync Manager to meet the E2.

  On the other hand, the HotSync Manager will always synchronize with my old T2.

  Palm Desktop is running on Windows XP.  I was using version 4.1.0, which came with my T2.  For the E2, I tried versions 4.1.0 4.1.4e and 6.2.

  I want to emphasize that Windows XP in turn is running in VMware Workstation 6.5 on Fedora 10 many (Linux 2.6.27.12 - 170.2.5.fc10).  Last Sunday I tried start Windows XP natively (which was a royal pain since I have hard drives to do so), installation of Palm Desktop 6.2 he and HotSync.  This configuration has worked insofar as the device is able to connect to the computer.

  Unfortunately only synchronize my to-do list and some 3rd party programs; He lost all of my notes, contacts, calendar of events and photos.  But that's another topic.

• Font book does not start after new created smart folder

  Hey gang.

  I tried to create a smart folder in the last font book. As soon as I did, he started on me beach ball.

  Since then, it hangs at startup.

  I dropped the file. Any other suggestions?

  B /

  Did you restart the computer after you remove the .plist?

  Make a backup using Time Machine or a cloning program, to ensure that data files can be recovered. Two backups are better than one.

  Try to set up another admin user account to see if the same problem persists. If back to my Mac is enabled in system preferences, the guest account will not work. The intention is to see if it is specific to an account or a system wide problem. This account can be deleted later.

  Isolate a problem by using a different user account

  If the problem is still there, try to start safe mode using your usual account.  Disconnect all devices except those necessary for the test. Shut down the computer and then put it up after a 10 second wait. Immediately after hearing the startup chime, hold down the SHIFT key and continue to hold it until the gray Apple icon and a progress bar appear. Startup is considerably slower than normal. This will reset some caches, forces a check for directory and disables all start-up and connection, among other things. When you restart normally, the initial restart may be slower than normal. If the system is operating normally, there may be 3rd party applications that pose a problem. Try to delete/disable the third-party applications after a reboot using the UN-Installer. For each disable/remove, you need to restart if you do them all at once.

  Safe mode - subject

  Safe mode - Yosemite

• Alienware Aurora r4 does not start with new graphics card.

  Hey,.

  I have an alienware aurora end of 2012 I believe.

  I currently have a series of 6800 AMD raedon graphics card, processor 3930 r9 k i7 and 8 GB of ram.

  I recently bought a MSI gtx 970 game to replace my old graphics card. I plug this card and it even lights up when I turn on the computer, but however my pc only happens to the start screen where I get the choice after pressing F2 and F12 and then freezes and I can't do anything. I then hear 3 beeps of inside my pc and then it proceeds to a blackscreen where my only choice is to turn it off manually.

  I tried to uppgrade my BIOS without much success (dident make it work), uninstall all graphics drivers from AMD, but nothing has changed.

  So I'm clueless I'm kinda a noob of the pc and have no idea what could cause this and would love help to explain what happens if all goes well if anyone knows a fix.

  THX in advance :)

  You you connected all power cables required PCIe 970? They are probably different config as AMD-6800. You should have 875w PS, but you might need to check that.

  Probably should have uninstalled AMD Driver Suite (catalyst) before removing the card from AMD.

  If card MSI BIOS a double switch, you can try another position.

  Try Mode Windows safe.

  What operating system do you use? Are you running the UEFI BIOS or legacy Mode?

• Does not start player BDP - BX58 Blu - ray * top of page menu screen more

  Sony unit works very well for about a year now.   Nothing has changed on this end - but - now when I turn on the drive blu - ray I see on HDTV: logo 1) Sony blu ray then) 2 wave horizontal blu and 3) a black screen.

  Instead of 3)-I use to get the * top of page menu * screen for slecting an dvd, browser, etc.

  I noticed that when the device is in step 3) connected to my ethernet (blue light on the power switch of the internet is fixed).    So, I guess that the DVD player is having trouble finding something on the Internet (?).

  At this point, I can't play any DVD - the screen remains black.

  The unit is connected to a SONY AV box.    What is strange, is that nothing has been changed (?)    The latest firmware changes have been installed more than 6 mos ago.

  Help, please.

  solved problem today ' hui - connected hdmi blu - ray box AV Player cable was loose in box AV.   cable just guaranteed and everything is back to normal.  Thank you all for taking a peek.

• Tecra A11 - 11N does not start after upgrading CPU

  Hello

  I would like to do an upgrade of the processor for my Tecra A11 i5 - 430 M 11N to a probably much faster i5 processor. I thought that the i5 - 580 M'd, but the laptop does not start when I installed this processor.

  I started the 430M, done some research on the internet and discovered that the 580 M has a very high FSB speed, and that is what probably does not work / not compatible with my machine.

  http://Ark.Intel.com/products/43537/
  http://Ark.Intel.com/products/49653
  http://Ark.Intel.com/products/49652

  and also http://ark.intel.com/

  Now, I went back to the computer store, returned the 580M and got an i5 - 560 M compared to its specifications as I've seen it would not compatible because it has the same speed of the FSB with the 430 M.

  I then later in the day tried to install this cpu as an upgrade, BUT alas!
  It STILL does not START ALSO.
  I was dumfounded left. The processors in the same line of the family are supposed to be compatible between them provided: lithography, FSB and socket type are similar.

  Or what I'm missing here?
  I did upgrades of CPU in many cases for desktop computers and laptops, and this is the first that has left me with no word to say!

  Please offer assistance or advice.

  Simon

  + The message has been modified.

  Hello

  Recommend to check this doc from Toshiba:

  + Can I put th CPU, screen, or motherboard in my Toshiba laptop? +
  http://APS2.toshiba-tro.de/KB0/FAQ35006D000RR01.htm

  Upgrading the CPU is not supported (officially).
  The point is that, even if the chipset would support the new processor, it would be possible that the laptop wouldn't start because of compatibility problems between the BIOS or other components on the motherboard and the new processor.

• Satellite Pro 460 does not start with the new drive in

  I recently received a Satellite Pro 460, but he had no hard drive.
  It starts great without a disc in but as soon as I put a new hard drive in it does not start.

  I thought that it might be again a hard drive, so I pulled out my old Toshiba Satellite with my old drive to work, and yet, it does not start.

  Someone has any ideas why this is and what I can do about it

  I think that you can not do much. Satellite pro 460 CDT, for example, comes with 2 GB of HARD drive. If you try to get it work with similar HDD without success, it may be defective IDE port on the motherboard.

  What HARD drive you are trying to use on this good old classic?

• Computer does not start after installing new graphics card

  HP-envy h8-1503
  I7 - 3770 k 3.5 GHZ
  10 GB of Ram
  Windows 8.1
  
  I tried to install a new edition of diamond Raedon 7770 to replace my old 7570 and when I try to start the computer I get 6 long beeps and the power light flashes 6 times. Everything is plugged in right and the video card turns on. It will not be output to the screen tho and the computer does not start!

  I fixed it, the problem was the safe boot in my bios, when I disabled the system booted and worked perfectly since! Thanks for the advice tho!

• After the new HARD drive does not start installation Qosmio G15

  I just got this G15 last week and one of the hard drives was bad. Put it in a new Bay 2 and it does not start. I took it back and it starts fine. I even changed the main hard drive Bay 2 HD and it starts up fine with a hard drive. It's something to do with the scores, I think. Any help appreciated.

  Hello
  I think that the boot order has been the bad HARD drive in the BIOS.
  At the new disk you do not installed any OS, and in my opinion, this is a reason for starting problems.
  Simply access the BIOS and change the boot order

• C870-19(r) satellite does not start with the new SSD

  Hello

  I will update the Toshiba Satellite C870 19(r) with a Pro 840 Samsung SSD, but it does not start.

  He said: not found system.

  Post edited by: joch333n

  None found system means that there is no system installed on the SSD drive...

  What you trying to do?
  You start from a disk in order to install the new system?

  In this case, you should disable startup secure in the BIOS.
  I also recommend moving from UEFI mode MSC!

• Pavilion HPE H8-1121: Pavilion HPE H8-1121 - new graphics card + power supply does not start after screen HP (Revisited)

  I have the same problem as this post 2013!  Ouch. Pavilion HPE H8-1121 - new map chart + power supply, does not start after HP screen.

  I installed a new power supply (Seasonic 620W), which works well.  I also installed a GTX 660Ti last year and it was works fine as well.  I recently bought a ZOTAC GTX 970 and attempted to install it, but it will not go beyond the blue HP screen and I get the same code of beeps (1 long, 3 short), who, seems, suggests that the video is not initialized.

  My BIOS date is 2011.

  Where can I find an update for this?

  I'm also using Windows 10, which I found on the HP site is not tested on my model and would probably not favourable to good use.  Should I do back up to 7 or 8?  and then update the BIOS?  Y at - it a update for my BIOS and where can I find.

  In any case, I hope that this is a solution.  Again, this is not a bad machine to be 5 years old.

  Thanks for any help!

  If the video card that you have purchased dose not a legacy vBIOS it will never start. An update of the BIOS doesn't solve that.

  It is likely that your new video card has a vBIOS UEFI and that only is for the PC motherboards newer than yours which have a UEFI BIOS. Your motherboard has a legacy BIOS. 2012 is the year of model when the UEFI BIOS more or less became the de facto on motherboards standard.

  I return it for a refund. Find the candidate of video cards that support the old BIOS. It can be inherited only or switchable vBIOS (legacy or UEFI) vBIOS.  I suggest looking at the site of Sapphire Technology. ZoTac is not known to provide enough information about their video cards in the way. You upgrade a pre-built desktop PC and it's different and a little more difficult to set up a DIY PC. I looked at the site of Zotac and see that nothing is said about their video vBIOS cards.  I would return to the map.  Carefully read the specifications of the video card. A candidate for your motherboard card must have inherited vBIOS support or simply, it won't work.

  ZOTAC (they don't say anything about their product vBIOS)

  https://www.ZOTAC.com/us/product/graphics_card/GTX-970-amp-extreme-core

  Sapphire Technology

  http://www.sapphiretech.com/catapage_pd.asp?cataid=305&lang=eng

  Because you look at game with 4 GB cards. Take a look at the following map. It has a double vBIOS. legacy and UEFI. http://www.sapphiretech.com/productdetial.asp?pid=640A98CD-0CF0-4191-B75C-CA2800111ADB&lang=eng