Don't check the cable connection no bootable device insert boot disk

Similar Questions

• Try to install Windows 7 via USB, El Capitan, Macbook Pro 2011 but get this error "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

  I am trying to install Windows 7 via USB, (El Capitan, Macbook Pro - early 2011), but this mistake "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

  You cannot use a USB on Mac 2011 Installer. Please burn the ISO on a physical DVD Windows (a DVD - R Carbon SL on the rate of burning slower is better) and use it to install Windows. The file Info.plist changes only allowing the creation of USB, but does not fully support a USB Installation.

• Is "PXE - MOF: PXE ROM. exit" then below I don't get, "No Bootable Device - Insert Boot Disk and press any key any" why?

  I bought the lifetime windows, defender security system, I also downloaded the windows repair and ran it, I even cleaned my c drive and defragmented, but I always get the same black screen. This is what it looks like.

  PXE - MOF: Exit PXE ROM.

  No boot device - insert boot disk and press any key

  /} In this area here, I slash turns clockwise

  Does anyone know how planned it and most importantly, how to prevent?

  Try to change your startup settings for...

  1 CD-ROM
  2 USB
  3. HARD DRIVE
  4. (if available) floppy drive
  5 LAN.
  You can change it by pressing the button shown next to "Boot Order"

• When I turn on my laptop it goes straight to no bootable device insert boot disk which I do not have?

  When I turn on my laptop it goes straight to screen blk which then no bootable device - insert floppy to start IE, which I did not

  You burn your set of recovery disks? If so start with them. No recovery set > Contact HP to order a set for a small fee.

  You can enter the BIOS by tapping /holding F10 key immediately after turning the power on and use Diagnostics to test your hard drive.

• My Toshiba laptop error: No. Bootable device-insert boot disk and press any key.

  When I put the bootable disc in I lost all my data. Now the problem is that I have a disk of Home Premium Windows 7 64 bit with product key number. This drive doesn't have SP1 on it, and when I tried to load the disc the message was that he could not install this drive.  This hardware of computers may not support booting to this disk.  Make sure that the drive controller is enabled in the Bios of the computer.  (I don't have the original software provided with the purchased used laptop computer).

  I called Toshiba and they said I needed a new drive and it would install for $149.00. I did not pursue it.

  Is my question there a way to get a Microsoft update disc that includes the original as well as the Service Pak data? I see several option on the web site but do not know what I can do.  It seems to me that everything I need is the service pak but cannot load the original software. Is there something in the BIOS I can change?

  Or is there another solution without buying all new software.

  Thank you

  Pickle, farmer

  Your PC Toshiba laptop includes a manufacturer recovery partition, and unless you have screwed up the hard drive, it should still be there and accessible...

  That's how access you... For Toshiba, press and hold the "0" BEFORE and during power-up Need you options recovery and overall the machine back exactly as it was when you bought it first.

  Several updates and hours later, you would still have a working machine. After re-installing your programs preferred and your applications, you must use the data backups made to recover what you have done on the machine since...

  It takes a lot of time, but it all works.

  An alternative...

  You can download a Windows 7 ISO, Windows 7 downloads , create a boot from it and pure media install Windows. The only catch here is that you must be able to read the sticker COST on the machine, the version of Windows and the key code. Then you re - install your favorite programs and do data backup procedure as above.

  If you have no backups of data or copies elsewhere and your Windows does not start, you need to make the drive of the machine, connect to another and copy the important of her data files, then place the player to the original host, using one of the methods above to re - install Windows...

• Re: Satellite L350: media test failure - no bootable device insert boot disk

  I just started a new Sat L350 upward and I can not go beyond the second page that says; Media test failure and no boot device, insert the boot disk and press any key.

  I have no disc and I'm stuck,

  Help!

  Hello

  This error message appears because the BIOS didn't not find a bootable device containing an operating system.

  What of the HARD drive? Is it recognized by the BIOS?
  Check in the BIOS settings; Press ESC and F1 to access the BIOS.
  There, you should check if the HARD drive (all details of the HARD drive should appear) is recognized.
  If this isn't the case, then it means that your HARD drive is dead and so you cannot boot from the HARD drive.

• PXE - e61: media test failure, check cable__pxe-m0f: exit pxe rom__no bootable device - insert boot disk and press any key

  My boyfriend knocked over a glass of soda on my laptop and it had the same error message for always, I'm not terribly computer savy, but 'shop' means they want 200-275 to fix! Help!

  It would seem that you have a hardware problem, caused by the spilled liquid.

  Hardware issues are beyond the scope of these Forums.

  I suggest that you take it to a reputable repair shop, computer room.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows 7 when I turn the laptop it says check cable connection pxe - mof: outgoing intel pxe rom no boot device insert boot disk and press any key

  Windows 7 when I turn the laptop it says check cable connection pxe - mof: outgoing intel pxe rom no boot device insert boot disk and press any key

  Hello

   

  1. What is the brand and model of the laptop?

  2 have you made any changes to the computer before the show?

   

  Method 1:  Change the boot order in the BIOS settings:

  See the following steps:

  Important: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  (a) start on typing Dungeon either F1, F2, F10, Esc, or DEL to enter the BIOS Setup.

  Warning: some manufacturers use F10 for recovery of the system.

  (b) glance to "Drive Configuration", "Boot order" or similar

  (c) check the second drive the first boot device CD/DVD and hard drive.

  (d) to save the settings and exit.

   

  Method 2:

  Step 1: Trying to boot into safe mode and see if that helps.

  Start your computer in safe mode:

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  If step 1 work, try step 2

  Step 2:  A clean boot to check if startup item or services to third-party application is causing this issue.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:

  http://support.Microsoft.com/kb/929135

  Note: when you're done to diagnose, follow step 7 in the article to start on normal startup.

• Error starting: "check the cable connection.

  Original title: that check the connection of the cable during the start up to the average?

  When I boot my computer says check cable connection? my computer crashed and has messed with it when you start to get in the system until I restored the computer to its original state. help I don't want to go through this again

  Hello

  ·          What version of the operating system is running on your computer?

  ·          Where there are changes made to your computer before this problem?

  ·          Question took place even after the computer has been restored to its original state?

  ·          It's a laptop or a desktop computer?

  This happens usually when the physical connection to the computer is not intact. Make sure that the physical connections are correctly configured.

• Equium M70 LAN adapter - it tells me to check the cable connections.

  When I connect a cable to the LAN adapter to the back of the laptop, how can the status LEDs should he show.
  I have only one view. Does that mean I have a problem.
  I am trying to connect to my ISP using an ethernet cable. He always says check cable connections.

  Near the port of LAN, there are two LEDs available: orange and green. When the LAN cable is OK and connection is where the Green led is permanent. The orange LED blinks when data transfer is available. Please check it carefully.

  If the Green LED is not on after connecting the cable LAN there are three possibilities:
  The LAN cable is defective
  Your router settings are bad (MAC settings or IP address)
  Or in the worst cases the LAN card on your laptop is defective (check in the Device Manager)

• Satelite L750 - "check the cable connection. no boot device. "

  Got the laptop for Christmas 2011, so it s only a month, I used it as usual and suddenly the internet froze and you t couldn't do something on Google chrome, the screen is black then after a while and the writing of this article has appeared-[https://twitpic.com/show/iphone/899pgv]

  What on earth am I doing?

  Advice in simple terms would be very useful; I m not a computer genius haha

  Hello

  It is really strange.
  Please, enter the BIOS settings and check if the HARD drive is listed there.
  The value of the default BIOS and check if the same error message comes again.

  As I understand it it's just that your laptop can not find the HARD drive.

• Satellite A30: PXE - E61 media test check the cable failure

  OK got this message on a cell phone of friends
  Others have played with him and made it worse, and now I received the laptop to try and fix.

  When you start to get

  PXE - E61 media test check the cable failure
  PXE - M0F outgoing PXC Rom

  If his tent to boot from the local network instead of the hard drive I have reset bios by default I disabled everything when I F12 boot to hard drive get the error message rΘation and one at a time, that nothing works even when I try to disable lan starts, he tries always to.

  When I try to install from disk backup it is hard disk not found, but in the bios the hard drive is located and can not boot from it.

  I tried with winxp pro disc to try not to get an OS on the laptop any partition to the OS but a blue screen with an error 0 x 00000050 CrashFree disk gives error 1170 if I remember correctly.

  I can't update the bios with new version because she needs windows, I can't stop the lan because there is no setting in the bios very minimul with about 4 useful settings in it.

  Is the hard drive turned or is this a bug in the bios that it detects drive hard, but does not assign a letter properly?

  If I try the recovery console in xp Setup there is no disk to read or write, if I maps the drive in recovery only the cd/dvd rom found no hard drive.

  Any help would be great thank you because I don't know what to do, I don't think that the hard drive is shot myself but maybe if I can get a laptop and try the hard drive what she will say if it is or not, but for now I'm stuck with no. had to go.

  I tried many things
  1. cdrom out and replaced plugs
  2. Jack hard drive out and replaced
  3 took Ram out and replaced
  4. start since the utility disk
  5. start from the winxp disk
  6. Windows XP recovery console no hard disk on c d e f g
  7 disc utility says no hard drive gives me a x: > promt error number 11030 invalid destination by car. Hard disk by bios HITACHI DK23FA-30-(PM)
  9 winxp error if I try to install 0x0000008e

  Post edited by: Shoa

  Post edited by: Shoa

  Hello Shoah

  You did what I would recommend.
  I remember what one of my friends has had a similar problem on an A200. But after the BIOS reset by default, he was able to install the OS from the recovery CD.

  The whole is very mysterious. It looks like a HARD disk failure, but the HARD drive is recognized in the BIOS. But have you checked the HARD disk in other laptop or computer?
  You can try to connect the HARD disk via the external USB HDD controller and could check if it s ok and could format.

  I recommend also to remove the CD/DVD drive and the HARD drive, then set the BIOS to default settings immediately (don't forget to save changes). Then try to power upward without the HARD disc and the drive.
  To my knowledge, you should get an error message.
  Then stop the laptop and put both the device in Notepad. Then go to BIOS and check if both devices are properly recognized.

  Finally, I must say that I don't know if my proposal will help m.
  If she won't help, you will need to contact an ASP in your country, because it really looks like a serious problem.

  Good luck

• "Connection error. Check the Internet connection. »

  I just installed my printer (an HP CM2320fxi upgrade). Everything works except ePrint/Web Services. The printer is connected directly to my router. It prints network computers. AirPrint works from iOS devices. It can scan to e-mail and documents are properly received by mail outside the network accounts (i.e. it must be connected to and talk to the internet). All the router firmware and the printer has been confirmed to date. all devices have been reset and restarted several times. However, if I try to activate HP Web Services for ePrint installation, I get the following error message: "connection error. Check the Internet connection. »

  After struggling with this issue for many months, including many discussions phone and email exchanges with technical support from HP, they finally sent me a replacement printer.  It works as advertised right out of the box.  I don't know what was the underlying problem, but the fact is that he couldn't be corrected with one of the solutions proposed in the discussions on this forum.  Apparently, there's HP printers out there with a lack of internet connection has nothing to do with a solution that is configurable by the user.  If you have one, then you will need to replace your printer.

  I can't thank HP for that.  They tried my patience and tenacity of the months before offering the only real solution.  They must know their products better than that and should have replaced my printer several months ago.  That being said, the tech person with whom I had most of my relationships, it was a nice guy.  I expect he's working under an edict on exhausting all possible tactics before agreeing to replace the unit.

  Good luck!

• How can I check the internet connection?

  How can I check the internet connection after the launching application?

  Method or property with the value true or false.

  Thank you!

  You don't have to see the 2nd answer, discuss blackberry.system.hasDataCoverage

• HP LaserJet Professional P1606: HP Web Services Installation - connection error. Check the Internet connection.

  I try to activate the Services Web of HP but connection error. Check the Internet connection. .

  I use the static ip address with the address of the preferred DNS: 8.8.8.8 and 8.8.4.4 and it does not work.

  I changed to DHCP as it does not work.

  I have a ZTE home modem router connected to the printer.

  The link below should help you.

  http://h30434.www3.HP.com/T5/user/viewprofilepage/user-ID/2585903

  Kind regards

  Oliver