Don't WLC 2504 media HA or not?
We have Cisco WLC 2504 (software version: 7.3.101.0) in our network and management access 10 points, we are now trying to build High Availability (HA) in the WLAN settings. So I need details that this existing platform is capable of supporting HA.
Required clarification as follows.
1 support WLC 2504 HA?
2. If the AP is supported if a license is required to enable it.
3. What is prerequisite software to enable it.
4 Setup guide to enable HA
Attached: existing WLC BOMs
HA PA SSO:
http://www.Cisco.com/en/us/products/ps10315/products_tech_note09186a0080bd3504.shtml
HA N + 1
http://www.Cisco.com/en/us/docs/wireless/technology/hi_avail/N1_HA_Overview.html
AP high availability
http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008064a294.shtml
Thank you
Scott
Help others by using the rating system and marking answers questions as 'response '.
Tags: Cisco Wireless
Similar Questions
-
Cisco WLC 2504 internal DHCP does not work properly
Hi all
I m trials with a Cisco WLC 2504 and some APs of 1832. I set up a DHCP scope on the interface of the controller with 2
a large number of different configurations, but the DHCP protocol does not work and Don t Access Point to obtain an IP address. My first question: is it possible to do DHCP for Access Points or only for wireless clients?
These are my interfaces:
Interface of the PA-Manager:
My DHCP scope:
Advanced DHCP:
I forgot something? Is there anyone using DHCP for its access points?
Thank you!
Hello
On Cisco WLC internal DHCP, you can add the option 43 to say where APs must register. In this case, they will try to resolve the DNS CISCO-CAPWAP-CONTROLLER or CISCO-LWAPP entry.
Let me explain briefly how AP-Manager works on WLC:
- Boots of Access Point and sends a discovery request to the management interface of the controller using the intellectual property you configured as DHCP Option 43 (as described above, it can be resolved by the DNS entry)
- Controller, sends it a response discovered that contains the name of the system, addresses AP-Manager, the number of access points already connected to each interface AP-Manager and the overall capacity of the controller.
- Joints access point controller using the less loaded interface AP Manager.
With this, every AP Manager must have a good configured interface and be connected to a different port, no LAG.
I drop a post here sometimes there is which might help:
https://supportforums.Cisco.com/document/118311/configuring-multiple-AP-...
Thank you
PS: Please do not forget to rate and score as correct answer if this answered your question
-
Cisco WLC 2504 - Access Points do not reach the controller
Hello world
We bougth a Cisco WLC 2504 with two AIR-AP2702I-UXK9 Access Points. The problem is that the AP do not join the WLC.
The output from 'show join ap stats' shows the following:(Cisco Controller) > view join ap stats summary all the
Database Mac EthernetMac AP AP name IP address Status
00:35: 1a: B1:A9:60 00:f2:8 b: f4:1 has: 9 c AP00f2.8bf4.1a9c 192.168.10.23 joined not
00:35: 1a: C9:99:B0 00:f2:8 b: 77:b7:fc AP00f2.8b77.b7fc not joined 192.168.10.24(Cisco Controller) > show join ap 00:35:1 detailed stats to: b1:a9:60
Synchronization phase statistics
-For the synchronization request has received... Does not apply
-For the synchronization completed... Does not applyDiscovery phase statistics
-Applications received discovered... 114
-Answers success of discovery... 114
-Discovery failure processing... 0
-Purpose of the last unsuccessful attempt of discovery... Does not apply
-Attempt to finally successful discovery time... 20:15:40.106 16 June
-Discovery attempt ultimately unsuccessful time... Does not applyJoin the live statistics
-Join applications received... 57
-Join sent successful responses... 57
-Processing of the join request without success... 0
-Purpose of the last unsuccessful attempt to join... Does not apply
-Attempt to join finally managed time... 20:15:50.414 16 June
-Join finally failed time... Does not applyConfiguration phase statistics
-Configuration requests... 114
-Answers configuration successful... 0
-Processing configuration failed... 57
-Purpose of the last unsuccessful attempt to Setup... Invalid license in the application configuration
-Attempt to finally successful configuration time... Does not apply
-Time finally failed configuration attempt... 20:15:50.810 16 JuneLast the decryption of the AP details failure messages
-Last message decryption failure reason... Does not applyDetails of recent disconnection AP
-Last AP connection failure reason... Does not apply
-Last reason for disconnection AP... Unknown failure reasonLatest summary join error
-Type of error that occurred in the last... Application of configuration rejected LWAPP
-Reason for the error that took place the last... Invalid license in the application configuration
-Time which occurred the last error to join... 20:15:50.810 16 JuneDetails of sign-out AP
-Last AP connection failure reason... Does not apply
Ethernet Mac: c 00:f2:8 b: f4:1 has: 9 Ip address: 192.168.10.23Would be grateful for the help.
Best regards
MarcHi Marc,
Make sure first that your controller has software code 8.0.x or above, if first better it. Here's the code recommended by TAC
Then, try the UX above deployment guide to begin. Under Advanced tab WLAN, you need to enable "of the first universal ap' in order to use this app provisioning & connect to the AP.
If you have more than 1 AP, then you must start 1AP using this application. Other access points that you can feed them upward, while AP original is also powered, so they'll use protocal called NDP & start them automatically
Let us know how it goes
HTH
Rasika
Pls note all useful responses *.
-
Windows Update don't load/Windows Media Player does not start
On XP Home Edition SP3, the last week I not was able to get the Windows Update page to load. There is no error message, IE8 seems to think that the loading of the page and there's code, but a blank white page in IE8. I discovered this problem after finding that Windows Media Player wouldn't start - again without error message. I look in Task Manager, the wmplayer.exe process runs for a few seconds, then disappears.
I have run a number of analyses of malware using Avira Free edition (now uninstalled), Spybot S & D, MalwareBytes Antimalware, Windows Defender, and Microsoft Security Essentials with no result or change.
I reset IE8 to its default settings and now find that I can't choose a search engine or view other pages on the Microsoft support site, such as http://support.microsoft.com/oas/default.aspx?gprid=assistance--il displays only the banner from the top on a white page. (I write this using Chrome).
Other posts on the forum about the update or Media Player starts does not seem to be on other versions of Windows, and I've not found anything about problems at a time.
Someone else met this kind of problem?
Thank you
KB2416400 only is installed, among those which you have listed
You are see the effects of an infection hijackware, very probably aggravated by a rootkit infection W32/Alureon-Variant. And I can say that the computer is infected since early August of 2010,at least.
OPTION A: Microsoft PCSafety provides users at home (only) with free assistance in dealing with infections by malicious software such as viruses, adware and spyware (including unwanted software).
https://support.Microsoft.com/OAS/default.aspx?&PRID=7552&St=1OPTION B (recommended in your case): See...
Cleaning a compromised system
http://TechNet.Microsoft.com/en-us/library/cc700813.aspxFollow the instructions in this post of mine in another forum (to-the-letter & in order!) to restore your computer to a State safe & functional: http://aumha.net/viewtopic.php?f=62&t=44636
If you need additional assistance with the clean install, please start a new thread in this forum: http://social.answers.microsoft.com/Forums/en-US/xprepair/threads
Wish I had better news for you. Good luck!
~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft
-
Recently, I realized that I don't have Windows Media Player on this pc, which limit myself by doing a lot of options on my smart TV. I tried to install, but whenever I do, I get a message saying that it is not compatible with my computer, when I chose the right options for windows 7 64 bit.
Maybe you have an edition of "N" of Windows, which would explain your problem.
Windows 7 N editions offer choices
http://Windows.Microsoft.com/en-us/Windows7/products/what-is-Windows-7-N-EditionMedia Feature Pack for Windows 7 N with Service Pack 1 and Windows 7 KN with Service Pack 1 (KB968211
http://www.Microsoft.com/en-US/Download/details.aspx?ID=16546Here is an alternative Player to try.
VLC media player
http://www.videolan.org/VLC/You could try the Windows Media Player control via Control Panel / programs and features / Turn Windows Features on or off / multimedia / Windows Media Player, make sure it is checked.
-
Cisco WLC 2504 with AIR-AP1131AG-A-K9
Hello
Can you help me for some info about AIR-AP1131AG-A-K9.
I have a wlc 2504, but I don't know if the AIR-AP1131AG-A-K9-supported 2504 wlc.
Can work this WLC 2504 with AIR-AP1131AG-A-K9 solution?
If so, guide.
Thank you very much
Gezimv
Check out this link. As long as you have software version 8.0.x 2504 version you can use 1131 AP with it. Nothing beyond software fate is more a series of support 1131.
http://www.Cisco.com/c/en/us/TD/docs/wireless/compatibility/matrix/compatibility-matrix.html#56735
HTH
Rasika
Pls note all useful responses *.
-
WLC 2504 cannot access the GUI...
Hi all
I'm not sure what I did wrong, the 2504 itself has only 4 ports and no port management but I heard it's actually port 1 (even if there are no labels for this). That's what I've done so far to try to access the GUI:
in CLI mode, I have
(1) put AP managament address like 10.151.55.129 255.255.255.224.
(2) I have activated the adminmode on port 1, which I assume is management port and enabling admin mode is the same as "no shut" on switches I guess; Here is the command I entered:
(Cisco Controller) config > adminmode port 1 turn on
(3) enabled HTTPS/HTTP through commands:
(Cisco Controller) config > activate network secureweb
(Cisco Controller) config > activate network web-auth secureweb
(Cisco Controller) config > network webmode enable
(4) I then reset system and verify that the changes took place to help display the synthesis network, as shown below. I also activated mgmt via dynamic interface to see if it makes a difference:
RF-network name... TEST_WIFI
Web Mode.................................... Enable
Secure Web view... Enable
Secure Web Mode Cipher-Option high... Disable
Secure Web SSLv2 Cipher-Option Mode... Disable
Secure Web Mode RC4 Cipher preference... Disable
OCSP........................................ People with disabilities
Responder OCSP URL...
Secure Shell (ssh)... Enable
Telnet...................................... Disable
Transfer Ethernet multicast... Disable
Transfer of broadcast Ethernet... Disable
Multicast/Broadcast AP mode... Address multicast: 225.225.225.225
IGMP snooping... People with disabilities
IGMP timeout... 60 seconds
Interval between IGMP queries... 20 seconds
MLD snooping... People with disabilities
MLD timeout... 60 seconds
Interval between MLD queries... 20 seconds
Period of inactivity of the user... 300 seconds
ARP timeout... 300 seconds
Cisco AP by default Master... Disable
Join AP priority... Disable
Mgmt interface wireless... Disable
Mgmt Via dynamic Interface... Enable
Filter MAC bridge Config... Enable
Safety of bridge mode... EAP
Mesh full sector DFS... Enable
Relief of AP... Enable
Support CMCC Auth Web... People with disabilities
Web Auth redirect Ports... 80.1
Web Proxy Auth Redirect... Disable
Bypass-Web Auth Captive... Disable
Web secure Web Auth... Enable
Quick change SSID... People with disabilities
Discovery of the AP - IP NAT only... Activated
IP/MAC Addr binding Check... Activated
Status of CCX-lite... Disable
oeap-600-WLAN-dual... Disable
oeap-600 local-network... Enable
mDNS snooping... People with disabilities
mDNS interval between requests. 15 minutes
(5) I installed my PORTABLE NIC to be 10.151.55.20 255.255.255.224 and connected to port 1 on wlc 2504; but I can't ping 10.151.55.29 nor do I navigate to https://10.151.55.29/. The port appears upwards (the flashing green lights on port 1 and Portable NIC also Flash).
Any help would be appreciated
If your connection to your laptop direct to port 1, then you have untagged the management vlan. Now you have configured for vlan 10, you must set to vlan 0.
You will then be able to ping to the management interface and connect to it through the user interface.
Sent by Cisco Support technique iPhone App
-
Re: Satellite L650D - 15K - Windows Media Player does not work
Hello
I bought a new laptop just before Christmas - windows media player does not and I don't know how to solve this problem. Any help would be appreciated?
Gasuro
Try to reinstall Windows media player.
Install version 12 of http://windows.microsoft.com/en-US/windows/products/windows-media-player -
Satellite A300 - easy key of Windows Media Player does not work
Can someone help me?
My easy key of Windows media player does not work and I have installed the package of value added. I don't know what's wrong all the other buttons seem to work well.
When the VAP is installed this button should be enabled to start Windows media player by default.
In any case, you can test the functionality if you set it to start another application.Configuration tool buttons you will find under:
Toshiba Assist (shortcut on the desktop) > Optimize > Toshiba Button support. -
Satellite M70 - media buttons do not work
Hi all
I have been using the Satellite M70 for 2 years now. My OS is XP SP2. The laptop comes with preinstalled express media player. And I still have the Express Media Player recovery CD.
For the reasons that I just formatted the C drive. This is not the first time that I did. But the last time after reformatting drive C Media buttons are still working fine. This time beside the reformatting, I have updated BIOS (from site Web from Toshiba) to version 1.50.
Now media buttons do not work. And not more than (browser and CD/DVD buttons) shortcut keys. I tried to reinstall the express media player by booting from the recovery CD and reinstall chose. But the problem persists.
Are there ways to get the media buttons still work?
Help would be very appreciated.
P/S: in case it is because of the update of the BIOS, is there way I can flash back to its original version?
Hello
I have the Satellite M70-159 with BIOS V 1.3. I'll try to update BIOS to version 1.5 to see if the same happen on my M70 laptop. I did not Express Media Player, but I will test it with running Windows XP Home edition.
So. Windows XP Home edition, I can use all the keys with Windows media player. Browser and all media buttons work well. With WinDVD too much work.
I don't really know why this does not work on your M70. Maybe you should remove all the stuff your laptop and do a clean install EMC and operating system itself.
-
Integrated media works does not on any web browser on the network.
To my office all of a sudden a large number of internet things stop working on our network. It doesn't matter what browser we use. Some things that don't work are that Pandora Radio, Grooveshark, Iheart radio, integrated pictures and YouTube videos on different sites and calendars on vrbo.com.
We can watch videos on YouTube and listen to music on jango.com so its not all media that do not work.
Since it is broad, I guess it has something to do with our server or network firewall. My office has a small business with Windows Server 2003 server. After that I installed windows updates, a few weeks ago is when I noticed these websites does not.
We also have a WatchGuard Firebox EdgeX20e but I did not any changes recently.
Ideas, any help would be appreciated.
Nate
Hey Nate,
You have a computer on a network in Windows Server 2003 domain, I suggest you to post the same query on Microsoft TechNet forum because we have experts working on these issues. See the link to the request message:
http://social.technet.Microsoft.com/forums/en-us/category/WindowsServerPlease let us know if you have any other questions about Windows. We will be happy to help you.
-
After a computer crash, I reinstalled Windows XP, but Windows Media Player does not work. I don't have reinstall all disks. Will install tools software system Dell, Sonic RecordNow, Sound Blaster Live, or CyberLink Power DVD play cd possible? Thank you.
original title: Media PlayerHello
1. What is the exact error message or error code when you try to open Windows Media Player?
2. what version of Windows Media Player?
3. What is the issue you are experiencing during playback of the CD?
I suggest you follow the Microsoft article reference and check if it helps.
Troubleshooting playback in the Windows Media Player for Windows XP: http://support.microsoft.com/kb/306317
Resources for the resolution of problems in Windows Media Player: http://support.microsoft.com/kb/843509
I recommend you to install the software provided by Dell disk and check if it makes a difference.
Note : using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.
-
My windows media player will not play a DVD
My windows media player will not play a DVD: Microsoft Windows 95 Version 5.1 (Build 2600.XP_SP3_gdr.111025 - 1629:Service Pack 3). Download a free version of media player to play the DVD? Please tell me the name of the upgrade and where to find the free download version, if so. Thank you!
First thing that you do not run windows 95 if your build number is 2600.XP_SP3 it is a build number of windows XP. Second, you will not be able to play DVDs using this version of windows and media player only. The reason for this is DVD is a standard that a group of companies shut down and basically, they demand rights fees to use, it codec, which you don't have. You will need get a program that has integrated these codec (or find them somewhere). Your best option for this is to completely abandon the but of the using Media player to play your DVD (unless you are looking to buy another piece of software). There is a free option that I use on my machine Windows 7 Basic its called VLC is a free player that makes just about every format out there (not sure Bluray). VLC uses its own codec (I think it's developed for the linux community orginially) rather than using the codec of the industry. You can find the program at http://www.videolan.org/
-
Original title: can not extract my music
I tried to extract the music in my media player library today, and I got an error messege that says: "Media player is not properly intalled, please install and try again." What should I do? How do we? Help, please!
Hi Lnoldon,
1. what version of Windows Media Player?
2. don't you make changes before the show?First of all, we recommend that you check if Rip music is correct. Check if Rip music location is set correctly.
See songs Rip (copy) from a CD to your computerCheck if protect copying of music is selected. If so, then deselect.
a. right click on the Windows Media Player toolbar, tap tools and then click Options.
b. click the Rip music.
c. Click to clear the copy protect music check box.
d. restart the drive and re - copy your music.Visit our Microsoft answers feedback Forum and let us know what you think.
-
Original title: Windows Media Player does not
Remember - this is a public forum so never post private information such as numbers of mail or telephone!
I have Windows XP Professional and have tried playing the CD through Windows Media Player. I get the message "Windows Media Player encountered a problem while playing the file. For any additional help click web help. "Then I do. Nothing here helps me. The player shows all my music but puts little red x showing that he can't play. Help! I downloaded version 11 of Windows Media Player, but it is saying the same thing.
Thank you.
Hello
1. don't you also get an error with the message code?
2 have you installed third-party readers part?
3. What is the format of the files you are trying to play?Follow these steps and check if they help.
Step 1:
I would have you readers of third party temporarily Uninstall and check if persists it to the question.
Step 2:
Most likely you need codecs to play these files with Windows Media Player. I suggest looking up codec in the Internet that supports the file format, download and install them.
See also:
Player Windows Media for Windows XP supported Codecs
WARNING OF THIRD PARTY
Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.See also:
Windows Media Player Error Message help
Aziz Nadeem - Microsoft Support
[If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]
Maybe you are looking for
-
Hello I'm pretty new on stage Apple Notepad I would like more information about the model MJLQ2AE/A This is the model sold to the Kuwait by a shop selling electronic retail with the specifications below Intel Core i7 Gen 4 2.2 GHz processor with Turb
-
How to merge two discs into one?
I recently updated my OS to Windows XP Edition Home Premium to Windows XP Pro. One way or another I have now two drives (Local 'C' and 'E' Local drive). When I start the computer it opens to E drive and I continually have a message that I don't have
-
I'm changing from AOL to an another ISP problems, I may not be able to delete messages in OE6. I think part of the IE8 package OE6? How do I change OE6 to the standard-setting version of AOL? Thank you Stem
-
How can I burn multiple files on a disc of SMEs without substitution of files?
I want to burn small video files on the same disc without replacing each other.
-
Absolute position and orientation of the camera
Hey folks, I'm banging my head against the wall trying to figure what I think should be a fairly simple expression.I'm trying to get my camera to an animatic of a moderator move offshore, and is not imported correctly on its system at least that the