Drive on Pavillion G7 failure

Similar Questions

• Unable to start my laptop, error: an unexpected error has occurred. Defective hardware such as a hard drive or the CD-Rom drive which is a failure. Status: 0xc00000e9

  When I tried to boot my Toshiba laptop, I get the message that unexpected error occurred.  Defective hardware such as a hard drive or the CD-Rom drive which is a failure. Status: 0xc00000e9

  \windows\system32\ntkrnlpa.exe file status: 0xc0000098

  Windows failed to load because the kernel is missing or currupt

  My computer did not come with an installation disc.  Best Buy has it

  I need my laptop, can anyone help.

  You download and make the disks to another computer.

  If you continue to have problems to take your machine to a repair shop.

• dvd - RW drive HP pavillion dv6 3180ea will write but not read!

  DVD - RW drive hp pavillion dv6 3180ea my laptop has stopped reading all discs.  However, it seems to be able to read and write the DVD-R Virgin

  I tried to diagnose the solution via the HP Support Assistant, without success.  Help!

  Hello

  You are welcome

  Can you let me know what follows.

  1. open windows control panel, open Device Manager, open the CD-ROM/DVD-ROM drives, right click on the device listed here and select Properties.  On the general tab, is there an error code in the device status area and if there is, what is the error code?

  2. What is the full version of the operating system you are using - IE Windows 7 64 bit?

  3. did you eject the drive tray and tried to clean the lens?  If you do not, try cleaning with a piece of soft cotton and check if it makes a difference.

  Kind regards

  DP - K

• "Your drive indicates that a failure may be imminent. Back up all important files and replace your player. »

  I got this error when using my video editing software all in rendering. "Your drive indicates that a failure may be imminent. Back up all important files and replace your player. "I did a backup using Dell Datasafe backup. My warranty is still in effect. What should I do? Ring for a new?

  Hi Williamz101,

  Error Code 2000-0151 indicates a hard drive failure. Please back up all your important data. Hard drive needs to be replaced.

  Thank you & best regards
  Mustapha S
  #iworkfordell

• Don't drive HP Pavillion G6 2210SA RED hard failure no bootable image message

  Hello

  I'm sure that the hard drive has failed. I tried reset hard with and without mains. I left the power on and after a while, I get a message saying that the selected boot image is not authenticated. I went into the BIOS, but there is no Diagnostics tool to test the hard drive.

  I'm happy to have another hard drive (if you can confirm that this is the question), but how to install Windows 8 once I have reinstall the hard drive? I can't even find my phone on the support forum and even fewer know about recovering from a hard drive failure.

  Can someone help please? Thank you.

  janner66 wrote:
  

  Very good idea. I'll post on some forums and see if anyone can help. Do I need to know my serial number of Windows 8 to make it work?

  No, the product number is encoded in the BIOS so you only have the recovery disks.

• Possible hard drive after clean install failure

  Appreciate it really all thoughts on this issue, because it drives me crazy and apparently get worse...

  I added 8 GB of RAM and an SSD Samsung 840 PRO in a Mac mini in 2011 about three years ago. At the time, the Fusion drive has just been introduced, and I found the online instructions to configure the combo HD SSD/existing as a Fusion player. After ironing out a few bugs, it worked perfectly (at least from the point of view of the user) for nearly three years. Significant speed increase, could handle more intensive applications of multiple users, etc.

  Three weeks ago, I decided to do a clean install. I wanted to get rid of all accumulated waste, as well as some of the Notification Center widgets don't work properly. Immediately I noticed the startup time is longer, but once connected, all seemed well. Just moved old files to the new system from a Time Machine backup, and everything worked well. In disk utility, it looked as if the OS has created two discs as a Fusion player, so I left as what.

  A week ago, I started notice stuttering in the downloaded movies in iTunes, which never happened before. Around the same time I started having the spinning beachball while running almost nothing: Safari with less than 10 tabs open (no video game), iTunes (inactive), Mail, etc... Impose anything. I performed first aid in disk utility and found no problem. I kept the activity monitor for the last 24 hours with nothing significant, other apps does not not showing the spinning ball.

  I saw someone else evoke here EtreCheck, so I did that and got two red warnings:

  Macintosh HD (2) /: 621,05 go-go (295,75 free) - 31 errors

  Drive failure!

  This error arose in both sections of the HD, as shown below:

  EtreCheck version: 2.9.11 (264)

  Report generated 2016-04-24 07:15:16

  Download EtreCheck from https://etrecheck.com

  Time 02:41

  Performance: Excellent

  Click the [Support] links to help with non-Apple products.

  Click [details] for more information on this line.

  Problem: Beachballing

  Description:

  Recently a clean installed on a system having and sad aftermarket, now without constantly slowing, beachball, movies stutter, etc.

  Hardware Information: ⓘ

  Mac mini (mid-2011)

  [Data sheet] - [User Guide] - [warranty & Service]

  Mini Mac - model: Macmini5, 1

  1 2.3 GHz Intel Core i5 CPU: 2 strands

  8 GB of RAM expandable - [Instructions]

  BANK 0/DIMM0

  OK 4 GB DDR3 1333 MHz

  BANK 1/DIMM0

  OK 4 GB DDR3 1333 MHz

  Bluetooth: Old - transfer/Airdrop2 not supported

  Wireless: en1: 802.11 a/b/g/n

  Video information: ⓘ

  Intel HD Graphics 3000

  DELL S2440L 1920 x 1080

  Software: ⓘ

  OS X El Capitan 10.11.4 (15E65) - since the start-up time: 13 hours

  Disc information: ⓘ

  SAMSUNG SSD 840 PRO series disk0: (128,04 GB) (Solid State - TRIM: No.)

  EFI (disk0s1) < not mounted >: 210 MB

  Boot OS X (disk0s3) < not mounted >: 134 MB

  Macintosh HD (2) /: 621,05 go-go (295,75 free) - 31 errors

  Drive failure!

  Storage of carrots: disk0s2 127.69 GB Online

  Storage of carrots: disk1s2 499.25 Go online

  Hitachi HTS545050B9A302 disk1: (500,11 GB) (rotation)

  EFI (disk1s1) < not mounted >: 210 MB

  Recovery HD (disk1s3) < not mounted > [recovery]: 650 MB

  Macintosh HD (2) /: 621,05 go-go (295,75 free) - 31 errors

  Drive failure!

  Storage of carrots: disk0s2 127.69 GB Online

  Storage of carrots: disk1s2 499.25 Go online

  USB information: ⓘ

  Western Digital My Passport 0748 1 TB

  EFI (disk3s1) < not mounted >: 210 MB

  Backup HD (disk3s2) backup Volumes/HD: 959,83 go-go (207,03 free)

  Computer, Inc. Apple IR receiver.

  MediaTek Inc. MT1887

  Apple Inc. BRCM20702 hub.

  Apple Inc. Bluetooth USB host controller.

  Lightning information: ⓘ

  Apple Inc. Thunderbolt_bus.

  Guardian: ⓘ

  Mac App Store and identified developers

  Launch system officers: ⓘ

  [loaded] 8 tasks Apple

  [loading] 152 tasks Apple

  [operation] 78 tasks Apple

  Launch system demons: ⓘ

  [loaded] 45 tasks Apple

  [loading] 156 tasks Apple

  [operation] 87 tasks Apple

  Launch demons: ⓘ

  [loading] com.adobe.fpsaud.plist (2016-04-15) [Support]

  Items in user login: ⓘ

  Dropbox application (/ Applications/Dropbox.app)

  Other applications: ⓘ

  [ongoing] com.getdropbox.dropbox.259552

  [loading] 393 tasks Apple

  [operation] 189 tasks Apple

  Plug-ins Internet: ⓘ

  FlashPlayer - 10.6: 21.0.0.226 - SDK 10.6 (2016-04-21) [Support]

  QuickTime Plugin: 7.7.3 (2016-03-12)

  Flash Player: 21.0.0.226 - SDK 10.6 (2016-04-21) [Support]

  Default browser: 601 - SDK 10.11 (2016-03-12)

  3rd party preference panes: ⓘ

  Flash Player (2016-04-15) [Support]

  Time Machine: ⓘ

  Automatic backup: YES

  Volumes to back up:

  Macintosh HD: Disc size: 621,05 GB disc used: 325,30 GB

  Destinations:

  My passport [Local]

  Total size: 959,83 GB

  Total number of backups: 32

  An older backup: 17 09/15, 01:57

  Last backup: 24/04/16, 07:00

  Backup disk size: too small

  959,83 GB backup size < (disc 325,30 GB X 3)

  Top of page process CPU: ⓘ

  3% WindowServer

  kernel_task 2%

  1% fontd

  0% askpermissiond

  Top of page process of memory: ⓘ

  1.45 GB com.apple.WebKit.WebContent (7)

  608 MB kernel_task

  Softwareupdated 475 MB

  ITunes 369 MB

  270 MB QuickTime Player

  Virtual memory information: ⓘ

  80 MB of free RAM

  used 7.92 GB RAM (1.98 GB being cached)

  Used Swap 0 B

  Diagnostic information: ⓘ

  April 23, 2016, 20:52:25 ~/Library/Logs/DiagnosticReports/com.apple.appkit.xpc.openAndSavePanelService_2 016-04-23-205225_ .crash [deleted]

  System/Library/Frameworks/AppKit.Framework/versions/C/XPCServices/com. Apple.AP pkit.xpc.openAndSavePanelService.xpc/Contents/MacOS/com.apple.appkit.xpc.openAnd SavePanelService

  April 23, 2016, 17:23 self test - passed

  April 21, 2016, 18:34:49 ~/Library/Logs/DiagnosticReports/Dropbox_2016-04-21-183449_[redacted].crash

  /Applications/dropbox.app/Contents/MacOS/dropbox

  I guess at this point that OS X put in place the incorrect Fusion drive, causing conflicts... But I don't know what to do about this. I have several backups, so this isn't a problem.

  This community is a great resource, thank you to everyone who adds. As I said, I'd like to advice for this...

  I think it is obvious that you have a disk failure. Could be the SSD, HD, or both.

• HP 2000: Hard drive short DST check - failure

  A ran a diagnostic equipment and received the message...

  ID of congestive M4UF88 - Q 6, 2847 - MFGJXG - 60WB03

  product ID EOP73UA #ABL

  I have no idea what that means!

  Is my bread cell phone. I can't on my account admin, only one guest.

  I lose and it is better to set?

  Thanks for any help

  Hello

  The error code 24 characters is a disk failure short self-test and would indicate that hard is defective and must be replaced.  This is also consistent with the problems you describe.

  If you want to replace it yourself, it is quite inexpensive - a brief guide on this is below.

  The player at the link below is an example of one that would be perfect for your laptop.

  Hard drive 500 GB

  The procedure to replace the hard drive starts on Page 54 of your maintenance & Service Guide.

  As you have upgraded to Windows 10 and as long as the previous installation of Windows 10 had activated Ok after the upgrade, you can simply use another PC to create the installation media for Windows 10 and then perform a new installation - it is all detailed in the guide on the following link.  Note: On the activation screen, select "I don't have a product key" - Windows will activate automatically once installation is complete.

  http://www.howtogeek.com/224342/how-to-clean-install-Windows-10/

  Regarding the existing personal folders on the failed disk, one possibility would be to place it in an external enclosure - is an example of the link below - connect to another PC and see if you can access your files.

  External 2.5 HARD drive caddy ".

  Kind regards

  DP - K

• Power driver - 8 victory State failure

  I bought a Lenova Ideapad a few months ago and have recently been using it more regularly. All of a sudden I'm getting blue screened when he returns to mode 'sleep' and get the error message "driver power state failure." and it takes forever to do restart and operation. I have just installed new software on this computer at this point, except for a flash, and PDF Creator is certainly not likely to be what is running at this point. Very frustrating that a voluntarily bought this machine because of his thought of SSD I was getting something reliable that could start quickly.

  Admin edited the title of the topic.

  
  

• Test hard drive HP Pavilion g6 failure

  Hello!

  My HP laptop has stopped working, I cannot get into windows, but can reach diagnostic tests to the boot sequence.

  The following text was reporeted on a fast hard drive test:

  Smart Check: PAST

  Short-DSN: FAILURE

  FAILURE ID: 9U0AJM-63570E-MFPX0J-60WH03

  PROD ID: B1J44EA #UUW

  Hard drive 1

  Test drive: FAILURE

  I guess I need to replace the hard drive?

  Kind regards

  BigRedMachine

  Hello

  Unfortunately, it seems that you will need to replace the HARD drive - the error code for short drive Self Test (DST) would indicate that hard is defective and must be replaced.

  The disc is a warranty item, so if your laptop is still under warranty, contact HP (with the error code 24 characters) and arrange for the replaced disk - you can check your warranty status here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

  Kind regards

  DP - K

• EliteBook 8540p: HARD drive, out of warranty failure

  Our laptop Elitebook 8540 P gives a terrible warning about the imminent demise of the hard drive.

  Failure ID is 90F953-5B67SD-XD7U3A - 60A 503

  Product ID is XT924UA #ABA

  Capacity is 320 GB

  So, looks like it's time to replace the HARD drive. I saved the document, making a system image and a repair disk. My question is, how do I proceed from here?

  It would also be nice to know why the warnings are produced. Operation seems normal.

  See you soon.

  Gerry6

  The warning is a good thing - in a bad situation. The hard drive is under surveillance and warning is always a heads-up before he finally dies on you, so you can get a backup.

  You can buy a Mobile SATA Hard Drive to install and then start with your repair disk to restore the Image of detail. Just be sure to get a capacity at least equal as the 320 GB or more.

• H8-1414: boot diagnostic hard drive test fail with "FAILURE ID: 90EF6C-00811-9XPK0K-60RC03.

  I ran diagnostic quick test for my hard drive boot and he responds with the message

  "FAILURE ID: 90EF6C-00811-9XPK0K-60RC03.

  Could someone tell me what the error id code?

  Thank you!

  Thanks to anyone who might help. I bought a new hard drive today and I'm about to install. Best wishes to all!

• Problem after installing the new drive on Pavillion G6-2320

  The original hard drive on my old book of 8 Windows Pavillion G6-2320 3 months crashed and I sent to HP and got the replacement of the hard drive (laptop still under warranty). They gave me support online printing that I just need to install it in the laptop and would not need the disc to install the operating system. (I had originally bought my own replacement hard drive and had error messages so chatted with online support who took care of the hard drive replacement confirmed that indeed one supplied with the laptop has been damaged)

  After you install the new hard drive and turn on the laptop, the following message appears on the black screen:

  Not found boot device

  Please install an operating system on your hard drive

  Hard drive (3FO)

  The F2 System Diagnostics).

  I went to F2 and test the hard drive. Everything was made. Help please!

  Thank you

  Hello:

  You will need to call HP support and ordering of a set of recovery disc for your model in order to install the operating system and the programs provided with your laptop.

  HP is not delivered replacement hard drives pre-configured with any software.

  They should also ship you the free of charge from the PC recovery discs is still under warranty.

• Moving from one machine to another HARD drive because of hardware failure, need to reactivate. Need help.

  Trying to help someone, their Compaq PC dies M/B or failure of the CPU. I am replacing a similar age of old IBM ThinkCentre o. Both machines have a valid XP license attached, the Compaq has XP Home, IBM has XP Pro. When installing the IBM HARD disk, I get the message that it must be enabled before it can connect, activation fails try to use the automated system, and when I called and tried to talk with a MicroSmurf of India, the female [explitive omitted] disconnected the call before I could try to explain the situation. (Both for customer service).

  I need to know how to get this thing to validate and let me log, because, at the very least, I kinda need to run the file and Settings Transfer Wizard so everything works out on an external drive.

  I tried to use the Hack on MyDigitalLife, Yes, I know, designed for crackers, but it is legitimate, but the tool it is infected with a Trojan, so I had to spend.

  Any help would be greatly appreciated. Remember that here, there is no attempt to violate the license: the 'new' machine has a valid license attached, the OS just needs to be informed of such.

  Thank you

  Licenses on these machines are more likely to OEM licenses and so are related to the first machine to which they were installed on.  So, when your Compaq is dead, then no license.  What you need to do is install the Compaq drive has failed as an extra drive (secondary) on the IBM. Sometimes, when you do this, the computer will attempt to start since incorrect disk.  If when you start your IBM machine, you must press the key at the beginning that sends you in the settings of the BIOS on the computer.  Somewhere in the BIOS settings, you must specify that you want the IBM to boot from the original disk which has been in the IBM instead of the disk from Compaq.  Once you do this, IBM should start from its own drive without licensing issues.  You should then see the Compaq drive mounted as a secondary drive under "My Computer".  You will then be able to copy or back up files, you need to save this record.

  HTH,
  JW

• Driver vista Power State failure Blue Screen of Death

  Please help me I think it's that I'm doing this... What is going on.. I have replaced the ram and video card, but has seen this problem before I did it... also just reinstalled windows vista... Please help https://skydrive.live.com/redir.aspx?cid=7cbac7e09f2ecb07&resid=7CBAC7E09F2ECB07! 105 & Thierry = 7CBAC7E09F2ECB07! 101 & authkey =! AEE_idLDpolnFKY

  Hello

  Those showed all CAUSE as a Windows component that means something different it led into error.
  Then ZIP or RAR the actuall minidump files and download them on SkyDrive and post a link here for us
  to analyze the other.

  Check this KB:

  The shutdown process does not terminate and you receive an error message on a computer that is
  running Windows Vista or Windows Server 2008: "Stop 0x0000009F"
  http://support.Microsoft.com/kb/972109

  ----------------

  You use Roxio or Nero programs? They have been known to cause this problem even
  If they worked well for a long period of time. If so check with their support.

  Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot BlueScreens - answers top 3 (+ 1 more).

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/blue-screen-plug-and-play-detected-an-error-most/3deab2fa-4000-4136-8c78-a3d22b1db009

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files.
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  ----------------------------------------------------------

  References to Vista also apply to Windows 7.

  This "might" be a power problem, even if this isn't the most common cause - in this case
  It seems that the PSU could be the fault.

  9F is probably a driver issue. Security/antivirus/antispware programs can also cause these issues.
  Have you added the recent devices or the updated drivers - don't forget to check in the Windows updates to see
  If a driver has been updated before this happen. This can also be caused by a loose card or cable
  and even a weak power supply.

  This error means that a driver does not properly support the power state. Check in Control Panel - device
  Manager to ensure that the drivers are not stop during sleep - double-click adapter - NETWORK adapter
  and WIFI - healthy and others - tab power management - uncheck allow the computer to turn off.
  Maybe the only has a problem.

  Start - type in the search - find MSCONFIG in top - right, click on – RUN AS ADMIN

  General tab - tick this box start Diagnostic - APPLY / OK - REBOOT

  Try it now. If the computer still blue screens thinks that video driver. Otherwise think the card NETWORK, Wifi, sound, or...
  (and it might still be video interacts with something else). See following message for my
  generic driver update methods.

  BCCode: 9F 0x0000009F<-- read="" this="">
  * 1167.html? order = date http://www.faultwire.com/solutions-fatal_error/Driver-Power-State-Failure-0x0000009F-

  ==========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do without if needed fail or the Vista DVD or recovery command prompt mode
  Options if your system was installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• HP mini says check Smart hard drive detected an immenent failure

  Went to use my mini and he had a black screen with a warning about the content of backup immediately because it has detected a failure immennent.  It won't let me something but run the proposed test and the test of hard drive has failed in this regard, a HP mini 110-3100. Not even yet 3 years old.  Can someone tell me if I lost all that on it or if there is a fix that I can do myself or take home. Could what cost be, no idea?

  Please and thank you!

  Probably the best chance to recover all your files would be to remove the hard drive. Then attach it to a > hdd USB adapter or a > USB hdd Enclosure. Plug it into a machine via USB and hard drive will appear as a drive to extra storage that you can browse and copy files on the hard drive of the machine to work. Of course, it depends on how much life is left in the drive.