Droid3 and Motorola Roadster

Similar Questions

• Portege 4010 Bluetooth - connection for samsung and motorola phones probs

  I have a portege 4010 with bluetooth. I am trying to connect to our two phones - a samsung sgh-e370 (newish) and a motorola V600 (2 years). Both have BT I downloaded and installed the latest Tosh BT stack (4.0.something). Shows Device Manager four drivers of tosh in BT - all are OK. I have allowed the discovery and allow the connection on the tosh. I did the same thing on the phones. When I run the "Add new connection" Wizard on tosh, he finds two phones and they appear under the devices section in BT Manager with the names I gave them on real phones. However, neither picked up phone tosh and showed no tosh by asking the numbers of pins on the phones.

  The net result is I now two phones display in BT Manager, but if I click on is and choose use log I recover the error "connection failed".

  If I try to find the portege using the phone, the samsung it is but motorola doesn't have. I can't get the motorola to twin with the tosh - it just says "unable to pair up with the portege.

  Any help gratefully received.

  RJ

  Hello

  I don't really know what is the problem in your case, but I did this a few times with my Motorola RAZR V3 and it works fantastic. The whole was finished for 1 minute. I hope that you do it in the right order, but I am writing to you the steps I did:

  1 activate the Bluetooth using the FN + F8 key combination
  2. install the new hardware if necessary (some of them)
  3. start the Bluetooth stack
  4 turn on the Bluetooth on the mobile phone (discoverable)

  5. Select the Express mode > next
  6. choose visible device listed in 'Bluetooth device list' > next
  7 choose to identify passkey (1234)
  8. Enter the key in the mobile phone. Twinning will be success

  I did it on this path, and now I can send all documents in my Tecra. If you want to use as a modem, you must do this:

  1. after peeling going on Next and configure the internet connection
  (provider number) > finish
  2. the new connection will be created in the Bluetooth stack utility
  3. you can start the numbering with double click or click with the right button of the mouse and choose 'connect '.

• Satellite A100-159 and Motorola Bluetooth Headset HS815

  Hello
  I can not connect the headset bluetooth Motorola HS815 portable satellite A100-159.
  I disable MS bluetooth and installed the latest Toshiba Bluetooth Stack V4.00.36.
  It's my internal bluetooth device from toshiba:
  077B = "internal Bluetooth CSR (19.2) v2.0 EDR.

  (1) I turn on the headset HS815
  (2) the Bluetooth manager sees a device, opening a pop-up windows where says "authentication failed", indicates the MAC ADDRESS of the helmet and ask me for the PIN.
  (3) I type in the PIN code "0000" default, but nothing happens!
  the HS815 is not connected,
  the Bluetooth Manager doesn't list any any device.

  It is:
  This Motorola HS815 headset is compatible with the bluetooth Satellite A100-159 card?

  Thanks a million in advance
  Filippo

  The error message indicates that something was wrong during the pairing process.
  This is silly, but important questions.
  Are you sure you have connected your headset and no other in the range? Really, the PIN is "0000" and you tyed in properly (maybe caps lock was on to your keyboard and something else has in fact been registered)?
  Delete all pairing if it exists, and then try again.

• MotoCare and Motorola customer support is a joke

  I bought MotoCare ($85) and needed to use it to get a replacement after water damage on my phone Moto X 2 ($800). After sending my phone ($50) and said I would get a replacement in 4 days... I wait 3 weeks and hear nothing.

  I contact the customer support, only to be told that my order was "cancelled". Without more explanation. I can't get a new phone (which I already paid for), I can't get a refund, and I can't even my broken phone back.

  I googled around and found countless stories similar to mine. What the fuck fucks, Motorola.

• E1500 and Motorola SB6141 cable modem

  I just got a new cable modem, Motorola SB6141 and when I connect the pc directly to the modem I get the blue light

  referring it works at high speed Gigabit Ethernet, but when I connect the E1500 light changes to amber which refers to just fast ethernet card.  Why such a fall?

  Do I need another map of the internet?  I have the realtek PCIe GBE Family controller or can I use the Intel 82579V Gigabit Network Connection.  Do I need a card that is 1000mbps?

  Thank you

  Yes, that's correct. You must have this kind of router. You can check the link below to learn more about other product specifications model of router.

  http://KB.Linksys.com/Linksys/UKP.aspx?VW=1&docid=ddcda37857b24a6eac2cd1e9ce266d65_Product_Compariso...

• Contacts blackBerry Smartphones Nokia and Motorola conversion in Blackberry contacts

  I got a deal of my new carrier for two new BlackBerry for the price of a more expensive. So I got a 9700 "BOLD", then my wife receives a Pearl 9100. Now, previously, we used two different phones, she was using a Nokia 3500C (GSM), while I was using a Motorola KRZR K1M CDMA (). I tried port both of our lists of contacts from phone above.

  First, I tried to copy the contacts to my wife in the Nokia SIM card. I then put the SIM card in its new BB, and it would not read the SIM card. I guess that's because BB is locked to a specific carrier. My carrier unlock our phones until we've been with them 3 months, that use me at the moment.

  Then I simply imported contacts into our PC with Nokia Software and then saved your contacts file to *. CSV format. I also did the same thing on my Motorola, with the Motorola software and also recorded one *. CSV file. When I tried to read the two contacts in the Blackberry Desktop Manager, he returned with an error:

  Error has occurred. Error code: 0 x 80040057.

  See the documentation.

  I think it has something to do with some of the fields that exist in a phone but not the other. I would have thought that their Intellisync software would know how to take care of this? It's the exact message even if I don't speak of contacts from the old phone to Motorola or the old Nokia phone.

  Same thing when I try to import the calendar entries too.

  This KB, provides a sample CSV (bottom of the KB, a link)... This might be useful in your quest.

  • KB11194 How to import contacts from a CSV file already created for the BlackBerry smartphone

  Good luck!

• Time Machine and Motorola SB6141 cable Modem is to create an internet break

  I had a SB6141 since I got cable internet 1/2014.  I had hung by a former Airport Extreme Base Station - it was all good.  I bought a time machine from Apple refurb > 6 months ago but < 1 year ago.  I had injury disruptions of the internet - I only know when I try to access the internet and airport utility shows time machine ok, but the router cable not connected.   I called the cable company, the last time it happened, and they showed the line was ok and had me hang directly up to the cable modem to get online - and I did!  They think that the router is messed up.  Once I unplug everything and hang it up, everything is ok.  Sometimes it happens one or twice a day, sometimes not for a week, it's not rhyme or reason - anyone have any ideas?   Thank you, Mike George

  The SB6141 is a good modem, and airport Time Capsule is a good router. But they don't seem to work together that well for a number of users including me.

  Make your choice... keep the modem and try another router... or... keep the time Capsule and try another modem. As soon as you make your choice, the faster your chances for a reliable Internet connection.

  You are not alone in your problems.  Take a look at just a sample of other users who have posted the same question:

  https://discussions.Apple.com/search?q=sb6141

• How can I configure Time Capsule 3 to and Motorola NVG589 to access the Time Capsule backup drive?

  I have ATT Uverse service and am ok with the performance of the WiFi of the NVG589. I want to configure my Time Capsule 3 to extend the network and be able to access the drive for backups Time Machine. I think I am following the steps in Airport utility, but once installation is complete I can find is no longer the time Capsule.

  I want to configure my Time Capsule 3 to extend the network

  The time Capsule cannot "extend" the network Uverse using a wireless connection, if that's maybe what you're trying to do. The time Capsule can only wireless "extend" the signal of another router from Apple.

  The Capsule can be configured to extend the network to Uverse if it is connected permanently... anytime... to the Uverse router using a connection through wired Ethernet cable.

  Please specify on what you're trying to accomplish, so that we can provide the correct steps.

• WRT610N and Motorola SB6120 DOCSIS 3.0 Cable Modem

  I've upgraded to the modem DOCSIS 3.0 in October due to higher bandwidth offerings of Comcast cable.

  Everything was fine until last week when I had recurring loss of Internet connectivity requires me to reboot/cycle my WRT610N and/or modem.

  I updated the firmware of the currently displayed 1.00.03 B15 and reset the router.  This did not help the situation.

  I also tried the suggestions mentioned here, including the Beacon Interval 75, threshold of Frag 2304, threshold RTS 2307, the wide-40 MHz Radio band.  Reset and cycled the router and modem after all this.  I also tried to power off my computer after each reset, all to nothing does not.

  I'm still losing Internet conncectivity several times per hour.  LELA is unable to repair the connection.  So far, the only solution is to reboot the router.

  Do I have a defective router (still under warranty), or is there a problem to interface with DOCSIS 3.0 modems.  Never had this problem with the old Comcast cable modem.

  My WRT610N is version 1 material.  Wireless encryption is WPA - AES, recommended by Beaver in a previous post in August.  Nothing is connected to the USB port on the router.

  Results of 'ipconfig/all' as follows:

  Microsoft Windows XP [Version 5.1.2600]
  Copyright (C) 1985-2001 Microsoft Corp.

  C:\Documents and parametres\joe > ipconfig/all

  Windows IP configuration

  Name of the host...: jb
  Primary Dns suffix...:
  ... Node type: unknown
  Active... IP routing: Yes
  Proxy WINS active...: Yes

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : hsd1.ca.comcast.net.
  ... Description: NVIDIA nForce Networking Controller
  Physical address.... : 00-14-22-xx-xx-xx
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  IP address...: 192.168.1.107
  ... Subnet mask: 255.255.255.0.
  ... Default gateway. : 192.168.1.1.
  DHCP server...: 192.168.1.1.
  DNS servers...: 192.168.1.1.
  Lease obtained...: Thursday, November 19, 2009 19:04:46
  End of the lease...: Friday, November 20, 2009 19:04:46

  I "x-out" the last 6 digits of my MAC address for security reasons.

  I would be very appreicate suggestions.  I strongly suspect that I would like to order a replacement from Linksys via warranty RMA router.

  Thank you for reading this.

  Sincerely,

  Joe

  Received the replacement router on 22-11-09.  WRT610N rebuilt with firmware v 1.00.03 B15.

  Installed with the current LELA software.  Wireless laptop was runing Vista 32-bit, Wired PC on XP Service Pack 3.

  Everything works normally again.  Replacement router dropped not a (wired or wireless) connection since its installation.

  I find that my original router (bought about 3/09) was defective.

  After replacement of the router, I upgraded my OS to Windows 7 (32-bit on laptop wireless, 64-bit Wired desktop).  No problem at all with the router.

  Hope this helps others.

  Joe

• Toshiba BT Stack 5.10.01 (T) and P990i Windows PAN network problem.

  Hi all

  I would like to ask if someone succeed PAN configuration between battery Toshiba BT and SE P990i?

  I have it set on Debian Linux and it worked like a charm, but it does not work under windows xp. P990i connects to the laptop but it lasts forever.

  Strange thing is that I've successfully connected two laptops using BT PAN without problems.

  Thanks in advance and best regards.

  Mariusz.

  p. s.
  If anyone has some ideas, please email me: fingerr (at) interia (dot) pl.

  Hello

  If there is any possibility try to connect your mobile phone with a few other non-Toshiba notebook. It will be interesting to know if there is the same problem under Windows XP Home edition.

  I don't have the same mobile phone but my Nokia and Motorola s wife works well with my Tecra and BT Stack 5.10.01.

• droid3 wifi

  I have a droid3 and every time I try to download anything now it ask me to do it on a wifi conection, this started 2 days ago. How can I start using the phone to download and it dosent matter the size of the file.

  Thank you

  Try to watch this...

  Go to settings/battery and saving of data/data manager. Is this allowed? If so it does not check if you will be able to download 3G or Wifi. You see an orange triangle in your notification bar?

• CLIQ and T505

  I use my CLIQ and Motorola T505 (mostly) successfully. However, I have a hiccup I don't know how to fix. When I'm in the car, I push the button on the T505 to turn it on, but then the music player on my CLIQ suddenly starts playing through the T505... I turn on the music player, it begins by himself, playing what was the last song I listened! The music player program is called "CMP_Amazon_FoFM_1.0.162" (which the option 'about' in the player's menu) and it came with the phone... it's not something that I downloaded and installed.

  Any thoughts?

  Thank you!

  I have it. When you press the button break read on the left side, it will start your Media Player. I didn't know this before, but I just did with my setup here.

  Your button may be blocked or stuck over this way the cause to think that you hit.

  Is there a way to disable.

  Go to the menu and tap Settings, wireless, Bluetooth settings, press and hold on the Motorola T505 until a screen opens.

  Now press options and turn off Media. Now the media won't play on your T505.

  I hope this helps, let me know.

• Phones of motorcycle and cars toyota

  well, I've been holding off the coast on this cause, that I was hoping the upgrade to lollipop would fix this, but we are still waiting for lollipop and who knows when it comes out.

  OK so I bought the turbo the day it was released in October, next month, I bought a new Toyota venza, so I connected with Bluetooth and it also has e-mail on it in order to listen to your messages and answer. Messaging has never worked, also Toyota entune, it's a bunch of applications that connect with your phone and make more of a center of entertainment to your radio in your car.

  anyway... I'm going to the concession for some kind of service and I'm talking with one of the mechanics and ask him why my phone sometimes disconnects and Messaging does not work. then he continues to tell me that for whatever reason as phones Motorola and only Motorola phones on kit kat I have this problem, Toyota knows about it and Motorola does, but no one is fixing it.

  so I guess what I want to know is if someone else has this problem with their phone and a Toyota brand?

  also is there anyone of Motorola who can better explain this?

  Thank you, kblgy

  
  

• Future updates will come from Motorola or Google?

  When Google will release an update of Honeycomb (as to enable SD card), we will be able to install this update immediately or need for Motorola to personalize it in order to release it then to the Tablet Xoom?

  And is there something that will tell us about the Xoom when a Xoom firmware or an update of the OS will be available for installation?

  I know the way that the apps tell us when there is an update but I don't know if it's the firmwares in a way even or OS updates will show.

  for non - us xoom, updates are coming us and Motorola xoom, it comes from google.

• Setup Motorola Atrix with Google TV via a HDMI device problem, help?

  I'm curious to know if anyone has had problems with implementation of devices via HDMI or using the Motorola Atrix (I'll be crossed this announcement on the forums Android and Motorola too to see what response I'll be there too).

  "After connecting my Atrix, turned to the Google TV (29') using the HDMI cable I got with the phone, I go to 'Settings' > 'Video input' > HDMI settings" > "Device list" > and click on "Enable", I get an error message that says:

  No HDMI devices have been found. Please check the connections.

  Thanks to a default function I chose, the "remote control" screen on my Atrix.

  I tried all four cards HDMI on the TV and received the same error message.

  Anyone would be able to help me solve this?

  I have the Sony NSX24GT1 24 and my phone is a Motorola Atrix Mobile phone black MB860 running on the Android 2.3.4 version.

  p.s. I really like my phone and I really like my TV and the possibility of using the two together! I really hope I can get help with this. Thank you!!

  Fixed! I had to press the input button on the very complicated, heavy Google TV remote control button (bad design).