DW create the subdirectory on the remote site.

Similar Questions

• ORA-19846: cannot read the header of the data file of the remote site 21

  Hello

  I have a situation or I can say a scenario. It is purely for testing base. Database is on 12.1.0.1 on a Linux box using ASM (OMF).

  Standby is created on another machine with the same platform and who also uses ASM (OMF) and is in phase with the primary. Now, suppose I have create a PDB file on the primary of the SEED and it is created successfully.

  After that is a couple of log, do it again passes to the waiting, but MRP fails because of naming conventions. Agree with that! Now, on the primary, I remove the newly created PDB (coward the PDB newly created). Once again a couple of switches of newspapers which is passed on to the wait. Of course, the wait is always out of sync.

  Now, how to get back my watch in sync with the primary? I can't roll method until the required data (new PDB) file does not exist on the main site as well. I get the following error:

  RMAN > recover database service prim noredo using backupset compressed;

  To go back to November 8, 15

  using the control file of the target instead of recovery catalog database

  allocated channel: ORA_DISK_1

  channel ORA_DISK_1: SID = 70 = device = DISK stby type instance

  RMAN-00571: ===========================================================

  RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.

  RMAN-00571: ===========================================================

  RMAN-03002: failure of the command recover at the 18:55:32 08/11/2015

  ORA-19846: cannot read the header of the data file of the remote site 21

  The clues on how to I go ahead? Of course, recreating the eve is an option as its only based on test, but I don't want recreation.

  Thank you.

  I tried like below:

  1 a incremental backup of the primary of the CNS where off the eve also taken primary backup controlfile as Eve format.

  2 copy the backup of the watch parts, catalogged them on the day before.

  3 recovered Eve with noredo option - it fails here with the same error pointing to the 21 data file.

  OK, understood. Try not to get back the day before first, rather than restore the controlfile and then perform the restoration.

  Make it like:

  1. take incremental backup of primary SNA, also ensures the backup controlfile format.

  2. copy pending, get the location of the data file (names) by querying v$ datafile on the eve. Restore the controlfile ensures from the backup controlfile you took on primary and mount.

  3. Since you are using OMF, the path of primary and standby data file will be different. (/). If you require catalog data from the database files pending.

  (Reason: you restore controlfile from elementary to step 2, which takes place from the main access road). Use the details that you obtained in step 2 and catalog them.

  4. turn the database copy by RMAN. (RMAN > switch database to copy ;))

  5 Catalog backup items that you copied in step 2.

  6. recover the standby database using 'noredo' option.

  7. finally start the MRP. This should solve your problem.

  The reason I say this works is because here, you restore the controlfile to primary first, which will not have details 21, datafile, and then you are recovering. So it must succeed.

  In the previous method, you tried to first collect all the day before, and then restore the controlfile. While remedial classes, always watch seeks datafile 21 as he controlfile is not yet updated.

  HTH

  -Jonathan Rolland

• Site Web is updated online, but seem to update the remote site pane?

  I use Dreamweaver 8.

  I am updating a website I have created initially.  I did this summer with success, until I did a major synchronization in order to cleanse the body of some really old files and make the site easier to manage for everyone.  Sync seems fine, but got it wrong in the end and ended up with the 'old' mainwebsite file and a mainwebsite file 'new '.  I then synced and it deleted the 'old' main site file (which is what I wanted to do).

  Now, when I do updates and put them on the remote site... they do not appear online.  Update the side "remote" site of the box of files.

  I tried to remove the site and then re - get the whole thing as if I've ever been in, but it is not yet published on the web.

  When I "re-" the site, he came with the old main site file, so I'm not sure what the field is SEO.  The old site file could be hiding somewhere on the FTP?

  Any ideas I could try?

  Sorry if I don't am not worded this correctly, I am new to Dreamweaver and use this site to learn the basics.  Thanks in advance!

  You need to be sure the site definitions are contained properly, if we're wrong, local or remote, you will have problems that you have.

  http://TV.Adobe.com/#VI+f1592v1760 Watch this video for a better explanation I can give.

  Brad Lawryk
  Adobe, Dreamweaver community expert
  Northern British Columbia Adobe User Group, Adobe user group manager

• FTP - cannot create the remote folder

  Help, please!
  
  I use DW 8 on iMac. When you download my site (using sync or put), all two used to work properly, I now meet the following error message and then I hunted:
  
  "error - cannot create the remote folder / folder name and the path--canceled by the user.
  
  I thought that the file may be corrupted somehow and removed completely from the site. On my next attempt, another file has triggered the same message, and so on...
  
  So I am unable to download my site and the bits and pieces that are on the web are truncated because the site is incomplete!
  
  What can I do?

  You may find it useful to stick with the DW FTP. Having the ability to
  Download up/dependent files is nice, as are the other (select features
  more recent, select recently modified, etc.).

  --
  Murray - ICQ 71997575
  Adobe Community Expert
  (If you * MUST * write me, don't don't LAUGH when you do!)
  ==================
  http://www.dreamweavermx-templates.com - template Triage!
  http://www.projectseven.com/go - DW FAQs, tutorials & resources
  http://www.dwfaq.com - DW FAQs, tutorials & resources
  http://www.macromedia.com/support/search/ - Macromedia (MM) Technotes
  ==================

  "hfeurstein" wrote in message
  News:fe8fti$K3U$1@forums. Macromedia.com...
  > To be honest, I don't know if I am running a firewall, I used to be a PC
  > user
  > but got so sick of stupid software windows, virus, constant need
  > updates etc that I bought an iMac and I can only assume that it is
  > running
  > some sort of firewall. In any case, I can confirm that during that time the FireFTP
  > has
  > completed download with no defects, this is why I would need is more DW.
  > Sounds
  > as if the investment is perhaps not quite interesting for a novice like
  > me
  > who really isn't a developer and just use it for simple tasks.
  > mercy
  > However, I like the ftp Sync feature and would like to continue
  > use it.
  > However, sounds as if there are a few flaws in the software
  > who
  > need to be ironed out.
  >
  > Having said all that, I really appreciate your help and especially
  > responsiveness, which is not easy to find these days. I'll take one
  > additional
  > Advisor you may have and thank you once more our support.
  >
  > Best regards, Harald
  >

• Traffic redirect Internet from the remote site on the main site using the tunel of vpn ipsec

  Hi all

  I have a problem to redirect internet traffic from my remote to the main site by the IPSEC VPN tunnel. The remote site is a Cisco 2801 router with ios (c2800nm-advipservicesk9 - mz.124 - 22.T) and the remote site has ios (C870-ADVSECURITYK9-M, Version 12.4 (15) T12, fc3 SOFTWARE VERSION). This redirect does not work and the last jump with extended traceroute form the remote site is the ip wan of the main site.

  Is there someone who can help me with the right settings this redirection via VPN?

  the remote site config file:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Tableau Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  crypto ISAKMP policy 8

  BA 3des

  md5 hash

  preshared authentication

  ISAKMP crypto key dgsn2010 address 41.223.X.X

  !

  !

  Crypto ipsec transform-set esp-3des vpn

  !

  vpndgsn 10 ipsec-isakmp crypto map

  Description at HQ

  set of peer 41.223.X.X

  Set transform-set vpn

  match address VPNHQ

  !

  interface FastEthernet0

  IP 41.223.X.X 255.255.255.0

  NAT outside IP

  IP virtual-reassembly

  IP tcp adjust-mss 1300

  automatic duplex

  automatic speed

  vpndgsn card crypto

  !

  interface FastEthernet 4

  192.168.11.1 IP address 255.255.255.0

  IP nat inside

  no ip virtual-reassembly

  !

  IP route 0.0.0.0 0.0.0.0 41.223.X.X

  VPNHQ extended IP access list

  ip licensing 192.168.11.0 0.0.0.255 any

  !

  the main site config file:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Tableau Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  crypto ISAKMP policy 10

  BA 3des

  md5 hash

  preshared authentication

  ISAKMP crypto key dgsn2010 address 41.223.X.X

  !

  !

  Crypto ipsec transform-set esp-3des vpn

  !

  vpncreo 10 ipsec-isakmp crypto map

  Description FOR bastos

  set of peer 41.205.X.X

  Set transform-set vpn

  match address 110

  !

  interface FastEthernet0/0

  Description OF WAN

  IP 41.223.X.X 255.255.255.240

  NAT outside IP

  IP tcp adjust-mss 1492

  vpncreo card crypto

  !

  interface FastEthernet0/1

  Description OF LAN

  IP 192.168.10.1 255.255.255.0

  IP nat inside

  automatic duplex

  automatic speed

  !

  overload of IP nat inside source list NAT interface FastEthernet0/0

  IP route 0.0.0.0 0.0.0.0 41.223.31.241

  access-list 110 permit ip any 192.168.11.0 0.0.0.255

  NAT extended IP access list

  deny ip 192.168.10.0 0.0.0.255 192.168.11.0 0.0.0.255 any

  permit ip 192.168.10.0 0.0.0.255 any

  ip licensing 192.168.11.0 0.0.0.255 any

  !

  You must configure the routing policy based closure for NAT can be invoked on the main site.

  Here is an example configuration for your reference:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a008073b06b.shtml

  Additionally, make sure that you don't do any NATing at your remote end, IE: you must configure the NAT exemption for all traffic from 192.168.11.0/24 to any (Internet).

  Hope that helps.

• Why can't I preview the changes before putting them live on the remote site in a browser?

  Help, please! I have inherited a website for editing and can't seem to get a preview of my changes without them going to live first. When I click on 'Live', the program hangs and I have to reopen. When I click on 'Preview in browser' he asks me to save the file or not and puts them on the remote site as well. I'm not particularly web savvy and learn on the way. I use CS6 on a Macbook OS X Yosemite.

  Your test server (Mamp) works?  If this isn't the case, you must start it.

  Nancy O.

• Create the remote database using dblink view

  Hello
  
  I have a small question for you.
  
  Is it possible to create the remote database using dblink view? Following syntax error
  
  create discover ViewName@DbLinkDame (ColumnName) as
  (select 1 double)
  
  "ORA-00905: lack of keyword.
  
  Is this possible at all?
  And particularly - is this possible when the remote database is MSSQL and I use heterogeneous services?
  
  I really appreciate your help
  Best regards
  Wojtek
  
  Published by: wojpik on October 21, 2009 03:59

  This is a workaround for a remote Oracle database (use the queue of work), however:

  http://asktom.Oracle.com/pls/asktom/f?p=100:11:0:P11_QUESTION_ID:597877500346143250

  but I have no idea if something similar is possible for MSSQL...

• How to check if the link exists in the remote site

  Hi all:
  
  Guys please can you me if there is a way I can check if the link exists in the remote site? for example
  
  < cfif hyper link to www.mysite.com exists in www.remotesite.com >
  good... We will continue
  < cfelse >
  Please add link to www.mysite.com before continuing
  < / cfif >
  
  Is this possible... you have to use the spider? If yes how?
  
  Thanks guys,.
  A
  

  to develop the excellent suggestion of tclaremont:

  You can use refindnocase() to search the returned by cfhttp filecontent
  call us at:

  http://www.yourwebsite.com">
  method http://www.VisitorsPage' = 'GET' result = 'Foobar '.
  ResolveUrl = "yes" getasbinary = "auto" >
  <>
  foobar. StatusCode is "200 OK" >
  ] * href [^ >] *' & replace (myurl, '. ',' \.',)
  'all') & '[^>]*>(.*?) <\>', Foobar.filecontent) >
  link
  
  no link...
  
  
  ... connection error or the web page you requested does not exist...
  

  of course, if the www.VisitorsPage site is sneaky and has the link to
  your site code page, but hide it with css/javascript, it's going to
  be difficult to discover using regexp... better just go and watch their
  Web site...

  Azadi Saryev
  SABAI - Dee.com
  http://www.SABAI-Dee.com/

• . Audio OGA works very well with local files, is to play at the remote site.

  I created a mini-site. It works well when I test it on my computer using local files, but the sound does play with it is downloaded on my remote site.
  The problem occurs on multiple computers, with several versions of Firefox, on Windows 7 and OSX Snow Leopard.

  Your server sends the correct MIME information in the Content-Type header? See this link for more information: https://developer.mozilla.org/en/Configuring_servers_for_Ogg_media

• Loggin to the administrator of the remote site redirects to localhost on the local server.

  This is certainly news to me. I created a Wordpress site locally and then uploaded to the remote server. For some reason when I connect I get redirected to the local host and the version installed locally in XAMPP. I tried to clear the cache in Firefox, but nothing helped. When Apache and MySQL are disabled in the XAMPP Control Panel, he always tries to redirect to the local server and I get the error "problem loading page".

  Also, strangely, when I disable XAMPP the CSS for the site on the REMOTE server is not displayed! Any ideas short of clear and start over? I can't even to the admin of the site to change the password.

  The fixed. Had to manually change the siteurl value in the table options in the remote database. Thank God...

• Access to the remote site VPN

  Hello

  I'm trying to solve a problem with the VPN, and I hope that someone could give me a helping hand.

  We have 3 offices, each with an ASA 5505 like the router/firewall, connected to a cable modem

  (NC Office) <----IPSEC----->(office of PA) <----IPSEC----->(TC Office)

  Internally, we have a full mesh VPN, so all offices can talk to each other directly.

  I have people at home, by using remote access VPN into the Office of PA, and I need them to be able to connect to two other offices there.

  I was able to run for the Office of CT, but I can't seem to work for the Office of the NC.  (I want to say is, users can remote access VPN in the PA Office and access resources in the offices of the PA and CT, but they can't get the Office of NC).

  Someone could take a look at these 2 configs and let me know if I'm missing something?  I am newer to this, so some of these configs do not have better naming conventions, but I'm getting there

  PA OFFICE

  Output of the command: "show run".

  : Saved
  :
  ASA Version 8.2 (5)
  !
  hostname WayneASA

  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 70.91.18.205 255.255.255.252
  !
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS lookup field inside
  DNS domain-lookup outside
  DNS server-group DefaultDNS
  75.75.75.75 server name
  75.75.76.76 server name
  domain 3gtms.com
  permit same-security-traffic intra-interface
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  inside_access_in of access allowed any ip an extended list
  IPSec_Access to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
  IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.2.0 255.255.255.0
  IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
  inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.224
  inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
  inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
  TunnelSplit1 list standard access allowed 192.168.10.0 255.255.255.224
  TunnelSplit1 list standard access allowed 192.168.1.0 255.255.255.0
  outside_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
  outside_2_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
  outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
  RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.5.0 255.255.255.0
  out_access_in list extended access udp allowed any SIP host 70.91.18.205 EQ
  out_access_in list extended access permit tcp any host 70.91.18.205 eq 5000
  out_access_in list extended access permits any udp host 70.91.18.205 range 9000-9049
  out_access_in list extended access permit tcp any host 70.91.18.205 EQ SIP
  out_access_in list extended access allowed object-group TCPUDP any host 70.91.18.205 eq 5090
  out_access_in list extended access permit udp any host 70.91.18.205 eq 5000
  Note to outside-nat0 access-list NAT0 for VPNPool to Remote Sites
  outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.2.0 255.255.255.0
  outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.5.0 255.255.255.0
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  IP mask 255.255.255.224 local pool VPNPool 192.168.10.1 - 192.168.10.30
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0
  NAT (inside) 1 0.0.0.0 0.0.0.0
  NAT (outside) 0-list of access outside-nat0
  inside_access_in access to the interface inside group
  Access-group out_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 70.91.18.206 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  Enable http server
  http 0.0.0.0 0.0.0.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set esp-3des esp-md5-hmac VPNTransformSet
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto IPSec_map 1 corresponds to the address IPSec_Access
  card crypto IPSec_map 1 set peer 50.199.234.229
  card crypto IPSec_map 1 the transform-set VPNTransformSet value
  card crypto IPSec_map 2 corresponds to the address outside_2_cryptomap
  card crypto IPSec_map 2 set pfs Group1
  card crypto IPSec_map 2 set peer 98.101.139.210
  card crypto IPSec_map 2 the transform-set VPNTransformSet value
  card crypto IPSec_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  IPSec_map interface card crypto outside
  card crypto outside_map 1 match address outside_1_cryptomap
  peer set card crypto outside_map 1 50.199.234.229
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 inside
  SSH timeout 60
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.100 - 192.168.1.199 inside
  dhcpd dns 75.75.75.75 75.75.76.76 interface inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal RemoteTunnel group strategy
  attributes of Group Policy RemoteTunnel
  value of server DNS 75.75.75.75 75.75.76.76
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list RemoteTunnel_splitTunnelAcl_1
  dfavier vUA99P1dT3fvnDZy encrypted password username
  username dfavier attributes
  type of remote access service
  rduske vu0Zdx0n3oZWFSaX encrypted password username
  username rduske attributes
  type of remote access service
  eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
  lestofts URsSXKLozQMSeCBk username encrypted password
  username lestofts attributes
  type of remote access service
  jpwiggins 3WyoRxmI6LZjGHZE encrypted password username
  username jpwiggins attributes
  type of remote access service
  tomleonard cQXk0RJCBtxyzZ4K encrypted password username
  username tomleonard attributes
  type of remote access service
  algobel 4AjIefFXCbu7.T9v encrypted password username
  username algobel attributes
  type of remote access service
  type tunnel-group RemoteTunnel remote access
  attributes global-tunnel-group RemoteTunnel
  address pool VPNPool
  Group Policy - by default-RemoteTunnel
  IPSec-attributes tunnel-group RemoteTunnel
  pre-shared key *.
  tunnel-group 50.199.234.229 type ipsec-l2l
  IPSec-attributes tunnel-group 50.199.234.229
  pre-shared key *.
  tunnel-group 98.101.139.210 type ipsec-l2l
  IPSec-attributes tunnel-group 98.101.139.210
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the pptp
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:6d1ffe8d570d467e1ea6fd60e9457ba1
  : end

  CT OFFICE

  Output of the command: "show run".

  : Saved
  :
  ASA Version 8.2 (5)
  !
  hostname RaleighASA
  activate the encrypted password of Ml95GJgphVRqpdJ7
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  192.168.5.1 IP address 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 98.101.139.210 255.0.0.0
  !
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS lookup field inside
  DNS server-group DefaultDNS
  Server name 24.25.5.60
  Server name 24.25.5.61
  permit same-security-traffic intra-interface
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
  Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
  Shelton_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
  out_access_in list extended access permit tcp any host 98.101.139.210 eq www
  out_access_in list extended access permit tcp any host 98.101.139.210 eq ftp
  out_access_in list extended access permit udp any host 98.101.139.210 eq tftp
  out_access_in list extended access udp allowed any SIP host 98.101.139.210 EQ
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 5090
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 2001
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 5080
  out_access_in list extended access permit tcp any host 98.101.139.210 eq ssh
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 81
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 56774
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 5000
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 902
  out_access_in list extended access permit tcp any host 98.101.139.210 eq netbios-ssn
  out_access_in list extended access permit tcp any host 98.101.139.210 eq 445
  out_access_in list extended access permit tcp any host 98.101.139.210 eq https
  out_access_in list extended access allowed object-group TCPUDP any host 98.101.139.210 eq 3389
  out_access_in list extended access allowed object-group TCPUDP range guest 98.101.139.210 5480 5487
  out_access_in list extended access permits any udp host 98.101.139.210 range 9000-9050
  inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
  inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
  inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0
  NAT (inside) 1 0.0.0.0 0.0.0.0

  Access-group out_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 98.101.139.209 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  Enable http server
  http 0.0.0.0 0.0.0.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac WayneTransform
  Crypto ipsec transform-set esp-3des esp-md5-hmac SheltonTransform
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  card crypto IPSec_map 1 corresponds to the address Wayne_Access
  card crypto IPSec_map 1 set pfs Group1
  card crypto IPSec_map 1 set peer 70.91.18.205
  card crypto IPSec_map 1 the transform-set WayneTransform value
  card crypto IPSec_map 2 corresponds to the address Shelton_Access
  card crypto IPSec_map 2 set pfs Group1
  card crypto IPSec_map 2 set peer 50.199.234.229
  card crypto IPSec_map 2 the transform-set SheltonTransform value
  IPSec_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 inside
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.5.100 - 192.168.5.199 inside
  dhcpd dns 24.25.5.60 24.25.5.61 interface inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
  tunnel-group 50.199.234.229 type ipsec-l2l
  IPSec-attributes tunnel-group 50.199.234.229
  pre-shared key *.
  tunnel-group 70.91.18.205 type ipsec-l2l
  IPSec-attributes tunnel-group 70.91.18.205
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:3d770ba9647ffdc22b3637e1e5b9a955
  : end

  Hello

  I might have found the problem.

  To be honest, I'm a little tired and concentration is difficult, especially when access between multiple device configurations. So second pair of eyes is perhaps in order.

  At the moment it seems to me that this configuration is the problem on the SITE of PA

  IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0

  This is an ACL that defines networks the and remote for a connection VPN L2L.

  Now, when we look at what connection VPN L2L this belong we see the following

  card crypto IPSec_map 1 corresponds to the address IPSec_Access

  card crypto IPSec_map 1 set peer 50.199.234.229

  card crypto IPSec_map 1 the transform-set VPNTransformSet value

  Now, we see that the peer IP address is 50.199.234.229. Is what site this? The IP address of the CT Site that works correctly?

  Now what that said the ACL line I mentioned more early basically is that when the 192.168.10.0 network 255.255.255.224 wants to connect to the network 192.168.5.0/24 should be sent to the CT Site. And of course, this should not be the case as we want traffic to go on the NC Site

  Also worth noting is that on the SITE of the above connection is configured with the '1' priority so it gets first compared a connection. If the VPN L2L configurations were in different order then the VPN Client connection can actually work. But it's just something that I wanted to point out. The actual resolution of the problem, of course, is to detach the configuration which is the cause of the real problem in which ASA attempts to route traffic to a completely wrong place.

  So can you remove this line ACL of the ASA of PA

  No IPSec_Access access list extended ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0

  Then, test the VPN Client connection NC SITE again.

  Hope that this will finally be the solution

  -Jouni

• Problem connecting to the remote site

  I created a FTP user on the remote server that works perfectly fine, when I click on test connection. Now, when I click on the remote view or download a file, or connect to the remote server I get this message-"Waiting for server" then I get this error message "connection to the remote host is lost. "Click the button connect to reconnect." I disabled my firewall too. This has been driving me crazy for a long time. Any source of help would be a great help.
  Thanks in advance.

  I had finally found the solution. My internet access point was behind the residential gateway, who created an internet cache (something like). I had to install cygwin which solved the problem. Just had to follow the simple rules to install and you have the problem solved. In any case, I would like to thank all those who had given their suggetions.
  Thanks again.

• Unable to create the internet site at 1024 x 768 on Tecra A9

  It's my problem. I always worked on a laptop Toshiba Satellite with a screen square (75 "wide). The resolution is set to 1024 x 768 (the maximum). + On this format, I founded applications page layout for my wordpress blog. font size and photo sizes. +

  Now, I have a new laptop on the side, Toshiba Tecra A9, it has a screen of 82.5 "and the resolution is Vista-set to a maximum of 1680 x 1050.
  Quality large screen, except for one thing: the reproduction of the pages of my blog (and in fact all the pages of the website) is ridiculous!
  The pages fill is more than 80% of the space of the screen of the monitor, but only 50%. This dwarfs bar that was once my blog page is literally floating in empty space otherwise.

  OK, I understand that one set standard must meet the new monitors somehow. But it happens in all the wrong ways. Compared to my 'old' image of the screen, the police of my texts swells now screaming size, while at the same time, have the images published + shrunk. +, this means a substantial loss of detail.

  I discovered that I can 'restore' it using the utility of Zoom and enlarge the view to 150%, the blogpage will cover most of the screen space, and images are wonderfully great. But the text already blown up expands as is good-no longer shouting at viewers, but Thunder...

  This cannot be the way it works. First of all: no surfer will take the trouble to play the magnify option.
  Now I have been able to reduce + sizes of the police in the HTML of my blog section for a normal effect. But this means that on my old screen (and I guess on that of all the others who are still working with a 3/4 "outdated" screen), texts will appear too small and unreadable.

  I checked my setup screen Tecra over and over again, can find no fault there.
  I've experimented with different choices of resolution, it is clear that the Tecra screen is designed for maximum results. .

  So what is happening, and how can I fix without losing on one of two different detection systems?

  > Now, I have a new laptop on the side, Toshiba Tecra A9, it has a screen of 82.5 "and the resolution is Vista-game to a maximum of 1680 x 1050. Quality large screen, except for one thing: the reproduction of the pages of my blog.

  Sorry, but buddy I put t understand why post you this here in Toshiba forum?
  The point is that you question has nothing to do with the laptop but only with your Web site design problem.

  Many notebooks (not only the portable Toshiba) are equipped with the 15.4 wide screen XGA and there are a lot of people (me too) who, Web design on portable computers with these screens.

  The fact is that, if your screen resolution is not set to 1024 x 768, then you must use the tools of additional web design (for example; Extension for Firefox: web developer tool bar) or you can use the special functions on s graphics program intensify or reduce the images or the entire site to your favorite resolution.

  I would recommend a few professional sites on Web design / webdevelopment for details.

  Good bye

• Expand the production VLAN behind ASA5510 to the remote site and 2821

  I have a 5510 ASA and here to contact one of the subnets behind this ASA out to my house which has a modem cable, a switch/router wireless and then behind that I have a router 2821.  I have read and it seems that L2TP can be the way to go, but can not find config examples.  Yet once again, I'd extend an and nail a permanent connection of one of VLAN in the production network to the bottom of my house using my cable modem and the 2821.  Examples of configuration would be very appreciated!  In addition, any recommendations for the IOS 2821 would be very appreciated.  Finally, the L2TP looks like how I need to go?  I enclose a very basic Visio diagram of what I'm trying to do.  Thank you, john

  You must L2TPv3.

  ASA does not support but will pass L2TPv3 borrowing.

  At work, you will need to add another router. L3 switches does not support it.

  The configuration of a router would be:

  Pseudowire-class test

  L2TPv3 encapsulation

  IP local interface loopback0 (this will be the source of the tunnel, can use any interface with the IP address access remote xconnect)

  !

  int fas0/0.30

  (do not put an ip address here)

  encapsulation dot1q 30

  pw-class xconnect X.X.X.X 1000 test

  X.X.X.X is the IP the remote router interface, it serves to "interface local ip" in the remote configuration

  Make sure that corresponds to 1000 (VC ID) on both sides

• Filtering of VPN and local access to the remote site

  Hello

  I set up vpn, filtering on all my VPN l2l. I have limited access to remote resources at the local level to the specified ports. It works perfectly.

  But I want to have as full access from local to remote networks (but still retain the remote access to the local level). VPN filter now works as I have two-way with a simple ACL. So is it possible to open all the traffic from the local to remote and all by limiting the remote to the local traffic?

  ASA 5520 8.4 (3)

  Thanks in advance

  Tomasz Mowinski

  Hello

  Well let's say you have a filtering ACL rule when you allow http local network traffic to the remote host

  LAN: 10.10.10.0/24

  remote host: 192.168.10.10/32

  The filter ACL rule is the following:

  FILTER-ACL access-list permit tcp host 192.168.10.10 eq 80 10.10.10.0 255.255.255.0

  I think that this ACL rule would mean also that until the remote host has been using source port TCP/80, it may access any port on any host tcp in your local network as long as it uses the source TCP/80 port.

  I guess you could add a few ranges of ports or even service groups of objects to the ACL rules so that not all well-known ports would be accessible on the LAN. But I guess that could complicate the configurations.

  We are usually management customer and completely different in ASA L2L VPN that allows us to all traffic on another filtering device and do not work in this kind of problems. But of course there are some of the situations/networks where this is not only possible and it is not a feasible option for some because of the costs of having an ASA extra.

  Please indicate if you have found any useful information

  -Jouni