Dynamic Cluster migration "Haswell" Intel and Intel 'Sandy Bridge' Cluster

Hi all

Need your help on this, on our below, we have two clusters ClusterA (EVC mode is Intel Haswell) and focus (EVC mode is Intel Sandy Bridge), the current problem we are facing right now is that we can not migrate from VM direct of clusterA to b, but successful once we stop the virtual machine and migrate to b. Webcam live migration of VM of focus to ClusterA now question. My question is, is there a way that we can migrate from VM direct ClusterA to b without changing the mode of the VCA on the two hosts?

Details of home:

Group A:
CPU: Intel Xeon CPU E5-2698 V3 2.30 Ghz
RAM: 256 GB
EVC: Intel "Haswell" generation

Group b:

CPU: Intel Xeon CPU 2.6 Ghz E5-2670

RAM: 256 GB

EVC: Intel 'Sandy Bridge' generation

If a processor can support level VCA XN, it can also support XN-1 to Xlevels 0. For example, a processor that supports Intel EVC baseline 'Sandy Bridge' generation has a level of EVC of L4. Therefore, it can also support VCA L0, L1, L3 and L2 levels. However, he cannot bear VCA level L5, which corresponds to the generation of Intel®'s "Ivy Bridge'. Intel EVC baselines are listed in table 1.1.

Ref: KB VMware: best vMotion compatibility (EVC) processor support

Thus, virtual machines that are running in your focus (EVC mode is Intel Sandy Bridge), should be able to move freely (vMotion) to b (mode of EVC is Intel Sandy Bridge) to ClusterA (EVC mode is Intel Haswell) and A to B provided that the virtual machine that is in your Cluster B vMotioned while in Group A and A is not in the power Cycle, if you put it off and on again then it will be new pickup EVC mode, otherwise it will continue to work with his original mode of VCA.

But if you take the case of the virtual machines running within your group, those who can not be vMotioned to group B, because they are running with mode higher CVS, canoe taken to lower VCA as live migration, you can migrate cold (power off and move)

Ideally if you want to reach vMotion compatibility between the two clusters, you must set the VCA mode for each group for Intel Sandy Bridge. But like asking you if you won't change EVC mode at all, the solution proposed would be

Turned off of the virtual machines in your A group phase by phase, turn cold migration from Group B, there and let the fashion of these machines virtual micro Cluster B EVC, then move them again in A Cluster, in short to realize all the VM in EVC of Cluster B mode. But you will always be in the face of challenge then if VM through the feeding cycle while in Group A, it will pickup Haswell VCA mode and you will lose compatibility vMotion for this virtual machine on cluster again.

so, what you're asking can be done using method above, but better would be to have two clusters in the VCA mode even if you don't have to worry about power cycles.

Note: You need to use vSphere Web Client.

Tags: VMware

Similar Questions

Satellite P750 - 10 c: HARD drive slows down - Sandy Bridge Cougar problem?

Hello

I have problem with my notebook Satellite P750 - 10 c with S/N: 4B478828K.
When I enabled AHCI in the BIOS, computer slows diametrically, day after day was worste and worste, so I tried to change from AHCI to IDE and it helped a little, but is still not good.

I tried to restore my system, but it did not help.
I read that Intel has released a version tapped for Sandy Bridge chipset, I have (HM65) SATA 3Gbs problem (I just checked in HD Tune and HARD drive is connected to the port of 3Gbs), so I think I got bugged version.

My laptop is not guaranteed, but Intel said they changed valid version, so where do I return my phone to fix.

Kind regards
Tomek

> I read that Intel launched buggy version of the chipset for Sandy Bridge.
The problem was a Cougar Point of Sandy Bridge chipset and not the main processor Sandy Bridge.

In addition Intel said that this issue affected only the SATA 2 to 5 and not ports 0 and 1.
Most laptops use only two devices SATA (HDD/SSD and ODD) using the affected ports 0 and 1.
That is why I think that your problem could be linked to the issue of Cougar Point the Sandy Bridge chipset.

By the way: not all Intel Sandy Bridge chipsets have been affected.

Regarding your question:
Usually if AHCI is enabled, the HARD drive must use the performance of SATA. If compatibility mode, the HARD drive would go at the speed of the IDE.
I think your problem is perhaps related to the problem drive HARD and not Intel problem.

dynamic cluster in Subvi connector pane

Hello

I would write a Subvi, which takes a dynamic cluster, accesses his property of [control] and acting on the results. I don't know if this is possible, or at least have not thought a viable option. If anyone has any ideas, I like to hear them. Let me know if I have defined my problem well enough.

This is possible, do a 'Variant' type connector

With the OpenG LVData toolset , you can get all the information you need.

Tone

Is it possible to migrate an application and drop one of the three types of plans?

Migrating applications is 11.1.1.3 to 11.1.2.2.300. Try to migrate an application and a company wants to only 2 of the 3 types of regime to be brought back. Is there a way to do this? Or to remove or hide the type of 11.1.2.2.300 if all 3 are migrated on?
Here is what has been tried, but he cuased a problem in the DB:
- Migrate an existing application that originally had 3 types of plan. Plan dropped type 1 and kept plan types 2 and 3
- Created 2 types of plan when creating the application in 11.1.2.2
- Initially built the contour using 11.1.1.3 LCM export dimensions and had to modify the XML to import. Edited plan 2 and made this plan type 1. Edited plan 3 and made this plan type 2. Had problems with the LCM/xml and finally finished by using the extractor contour and loading by using the outlineload utility. Dimensions are now based.
- Initially, wrong Bishop Calc. To change the value of the hsp_systemcfg for the type of plan table = 2 instead of 3 as it was in the table.
- Calc Mgr shows that type of plan 2 and no plan to type 1.
Any ideas?

Probably the best way to rebuild the application and then reload the hierarchies or hack files XML of LCM, if 11.1.2.3 then you would be able to create/delete plan types.

See you soon

John

http://John-Goodwin.blogspot.com/

Why my dynamic link does not work and why I get these error messages?

IM using CS6 of still using Pr CC 2014... I have not access to the dynamic linking option either... Can I get assistance with my problem...?

Woks only dynamic as link between versions. Then PR CS6 to EN CS6. There is no dynamic relationship between PR CC and EN CS6.

For questions and a link to a workflow, see:

http://helpx.Adobe.com/Encore/KB/Encore-CS6-installed-cc.html

Dynamic tab Shell cut Images and text

I use the Shell dynamic tab on a page and try to get a few images-links and output text display correctly in the global toolbar. I want the links to the image on the left side of the toolbar and the output on the right side text. The problem is the pictures are cut off and the text is envelope in a small space and is not entirely legible. The images are 32 x 32 pixels. Should I resize them to something smaller? I tried to use small images previously, but it seems simply push down and still cut.
The full text of output must be "logged in as: username", but it is force into a small space and cutting the username like this:
Connected
as:
username (this line is not visible in the toolbar)
Here is my code. Any help is appreciated.
...
"< af:pageTemplate viewId="/oracle/ui/pattern/dynamicShell/dynamicTabShell.jspx "value =" #{bindings.ptb1} ' "
ID = "pt1" >
...
< f: facet name = "globalToolbar" >
< af:panelGroupLayout id = "pgl5" layout = "horizontal" valign = "top" >
< af:toolbar flex = '1' stretchId = 'stretch1"id ="tb1">
< af:group id = "grp1" >
"" < af:commandImageLink text = "' actionListener =" #{tabmanagement.dashboardSelected} "id ="cil1"icon="/images/AsIconDashboard.png "partialSubmit ="true"/ >
"" < af:commandImageLink text = "' actionListener =" #{tabmanagement.toggleSelected} "id ="cil2"icon="/images/AsIconToggle.png "partialSubmit ="true"/ >
< / af:group >
< af:spacer id = "stretch1" width = "10" height = "35" clientComponent = "true" / >
< af:outputText id = value = "#{tabmanagement.loggedInAsText}" / "loggedInAsOT" >
< / af:toolbar >
< / af:panelGroupLayout >
< / f: facet >
...

Move text output of the globalToolbar facet in the facet globalSearch fixed problems and gave me the results:

...

Icon="/images/AsIconDashboard.png" partialSubmit = "true" / >

Icon="/images/AsIconToggle.png" partialSubmit = "true" / >

...

...

Very new to photoshop, I try to make changes to a photo and set up as a dynamic object, but after the selection of dynamic object, the grid appears and my photo dissppears

Very new to photoshop, I try to make changes to a photo and set up as a dynamic object, but after the selection of dynamic object, the grid appears and my photo dissppears

Well, something's wrong with Photoshop. Try to close Photoshop, and then press Command + Option + shift as you restart Photoshop. You will be asked to clear the Photoshop preferences. ATTENTION: you will lose all current preferences.

procedure that will dynamically build the query data and table Medallion

Hi people,

I write a procedure that dynamically build the query data and insert in the table "dq_summary".
enforcement procedure with success and data not inserted into the table 'dq_summary '.

I have thin problem in code attached below
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

FOR rep IN cur_di_attr
      LOOP
        dbms_output.put_line ('d: ');   
        
        BEGIN
          EXECUTE IMMEDIATE 'SELECT table_name FROM ' || sum_tab || ' WHERE id = ' || rep.attribute_id INTO rep_tab;
          dbms_output.put_line ('rep_tab: '||rep_tab);
          run_query := run_query || ' ' || rep_tab || ' WHERE ' || nvl(wh_cond, '1 = 1');
          EXECUTE IMMEDIATE run_query INTO end_rslt;
        
          EXECUTE IMMEDIATE 'UPDATE dq_summary SET ' || prop || '_' || p_code || ' = ' || end_rslt || ' WHERE attribute_id = ' || rep.attribute_id;
          dbms_output.put_line ('e: ');      
          dbms_output.put_line ('rep_tab: '||rep_tab);
          dbms_output.put_line ('end_rslt: '||end_rslt);
          dbms_output.put_line ('f: '); 
        EXCEPTION
          WHEN no_data_found THEN
            rep_tab := '';
            sum_tab := '';
        END;  
      
      END LOOP;

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
but in the procedure below must be run several times

create or replace
PROCEDURE DQ_REPORT_PROC
AS
  prop                              di_proposition.pro_name%type;
  col_var                           VARCHAR2(100);
  p_code                            dq_parameter.para_code%type;
  sum_tab                           di_proposition.summary_table%type;
  run_query                         dq_parameter.run_query%type;
  wh_cond                           dq_parameter.where_cond%type;
  end_rslt                          VARCHAR2(20);
  rep_tab                           VARCHAR2(50);
  v_error_msg                       VARCHAR2(200);   
  v_error_code                      VARCHAR2(200);  
  v_object_name                     VARCHAR2(50)                          DEFAULT 'DQ_REPORT_PROC';
  v_iss_no                          VARCHAR2(20)                          DEFAULT NULL;
  CURSOR cur_di_prop IS 
    SELECT upper(replace(replace(pro_name, ' '),'-')) pro_name
      FROM di_proposition;
  
  CURSOR cur_di_para IS
    SELECT upper(para_code) para_code, run_query, where_cond
      FROM dq_parameter;
  
  CURSOR cur_di_attr IS 
    SELECT attribute_id
      FROM dq_summary;
BEGIN
  
  DELETE FROM dq_summary;

  INSERT INTO dq_summary (attribute_id, entity_name, attribute_name, data_champ) 
    SELECT a.attribute_id, b.entity_name, a.attribute_name, a.data_champ
      FROM di_attribute_master a, di_entity_master b
     WHERE a.entity_id = b.entity_id;

  FOR c_prop IN cur_di_prop
  LOOP
    prop := c_prop.pro_name;
    
    BEGIN
      SELECT distinct SUBSTR(column_name, 1, INSTR(column_name, '_')-1), summary_table
        INTO col_var, sum_tab
        FROM user_tab_cols a, di_proposition b
       WHERE a.table_name = 'DQ_SUMMARY'
         AND upper(replace(replace(b.pro_name, ' '),'-')) = prop
         AND SUBSTR(a.column_name, 1, INSTR(a.column_name, '_')-1) = upper(replace(replace(b.pro_name, ' '),'-'))
         AND upper(b.status) = 'Y';
         
         dbms_output.put_line ('col_var: '||col_var);
         dbms_output.put_line ('sum_tab: '||sum_tab);
         
    EXCEPTION
      WHEN no_data_found THEN
        col_var := '';
        sum_tab := '';
    END;

    dbms_output.put_line ('a: ');

    FOR para IN cur_di_para
    LOOP
     dbms_output.put_line ('b: ');
      p_code := para.para_code;
      run_query := para.run_query;
      wh_cond := para.where_cond;
      dbms_output.put_line ('c: ');
      FOR rep IN cur_di_attr
      LOOP
        dbms_output.put_line ('d: ');   
        
        BEGIN
          EXECUTE IMMEDIATE 'SELECT table_name FROM ' || sum_tab || ' WHERE id = ' || rep.attribute_id INTO rep_tab;
          dbms_output.put_line ('rep_tab: '||rep_tab);
          run_query := run_query || ' ' || rep_tab || ' WHERE ' || nvl(wh_cond, '1 = 1');
          EXECUTE IMMEDIATE run_query INTO end_rslt;
        
          EXECUTE IMMEDIATE 'UPDATE dq_summary SET ' || prop || '_' || p_code || ' = ' || end_rslt || ' WHERE attribute_id = ' || rep.attribute_id;
          dbms_output.put_line ('e: ');      
          dbms_output.put_line ('rep_tab: '||rep_tab);
          dbms_output.put_line ('end_rslt: '||end_rslt);
          dbms_output.put_line ('f: '); 
        EXCEPTION
          WHEN no_data_found THEN
            rep_tab := '';
            sum_tab := '';
        END;  
      
      END LOOP;    
    END LOOP;
  END LOOP; 
  COMMIT;   
EXCEPTION
      WHEN OTHERS THEN
         v_error_msg   := SQLERRM;
         v_error_code  := SQLCODE;  
         TRACKER_LOG_EXECEPTION(v_iss_no, v_object_name, CURRENT_TIMESTAMP, v_error_msg, v_error_code);
      COMMIT;        
  
END DQ_REPORT_PROC;

Published by: BluShadow on February 7, 2012 12:04
addition of {noformat}

{noformat} tags.  Please read {message:id=9360002} and learn to do this yourself in future.

903830 wrote:

I write a procedure that dynamically build the query data and insert in the table "dq_summary".
enforcement procedure with success and data not inserted into the table 'dq_summary '.

I'm sorry. But there is no kind of say that way. The code is undesirable. The approach is wrong. This will not happen. This will cause the fragmentation of memory in the shared Pool. This will lead to another session being impossible to analyze the sliders because of the fragmented memory.

Not only that. The underlying data model is questionable.

All this seems a candidate perfect as an example of how NOT to design and code and use Oracle.

Sandy Bridge and PCI channels/performance question

I was doing emergency surgery on my old HP and I remembered that I have a couple of old graphics cards lying around. And that made me think of my collection in constant expansion of hard drives and never less in less free time, backups, and Sandy Bridge platform limited channels PCI and their (real? theoretical?) effect on performance with cards cards additional specifically RAID. If I'm covering old ground, let me know.
As I understand, there is not much to be gained by installing an old ATI HD2400 Pro or similar in a new computer, what I'm really wondering is - after installing the card and a third running monitor on it - of the main graphics card and related parts of my system would suffer a slowdown similar to what might be expected if a RAID card is installed.
(And no, I don't mean to revive the heated discussions of Sandy Bridge / X 58.) Is it you like someone ' one, anyone - let them be above!)
I am just wondering if it might be a worthwhile project to compare benchmarks with and without a second graphics card installed and if someone thinks it would be a logical way to see no effect on the allocation of 570's PCI channels alone, without the complication of a real external RAID array question (and the enormous benefits it would probably).

everything you need to know here

http://forums.Adobe.com/thread/854514?TSTART=30

This has been put to bed in time there...

Scott

ADK

Effects of lightsaber using the dynamic link with Premiere pro and After Effects CS4

Hi all
I'm working on a video project and that you want to add a lightsaber effect, but a layer which is suppose to be transparent isn't using dynamic links.
I shot the video in my head, and everything else hidden. I made a flash body to put my head on. Now I know how to make a lightsaber in After Effects CS4. (starting with comp 1 with videos making a white solid layer, and then using the tool pen to make the sword. Then copy the sequences video and place it in comp 2. Then to return to comp 1 and remove the video sequences. then on comp 1 making a SOLID BLACK LAYER {that's the problem} and place it under the layer of white. Then duplicate the white layer 3 times. Changing each feather white layer mask to make the glow. so going to comp 2 and take the 1 model and her nest to model 2... Then change the blending mode of the model nested 1 to the screen.
The main timeline in Premiere Pro CS4 and I have the video layer 1 to Photoshop file which is pink and the background of this project. I made a dynamic link to After Effects and copied and pasted the video images and flash to the comp. Here, I made the lightsaber.
That is the problem. The model of dynamic links with video, flash and the lightsaber will not show my pink background in Premiere Pro shows him my video, flash and lightsaber but the background is black. In case of problems, I noticed if I turn off the LAYER BLACK for the lightsaber effect, I see my pink background with video and flash sequences and the glow of sabre, but my blue lightsaber color will not appear.
Do more problems I set photoshop to lightsaber model file and I see the video, the flash, the lightsaber but I think because the background is pink I don't get a color glow to the sword (vilot color)
If the layer of black is supposed to be transparent, so why can't see my background in Premiere Pro using dynamic links?
appreciate any help I can get,
Thanks in advance.
Mr. PETER K
P. S. - one-way I kinda had this work was I took one of the masks of white and copied and pasted layers in nested layer comp 1. Adjusted to the width of the mask and the pen and I got a glow of blue ok. You just can't mask width too because it shows a lot of black. It is not as good as I want and I hope someone can help...
Thank you again...

Well, blend modes don't create transparency, so the behavior is correct - because technically, the background of the model is ignored for the mix of operations, in areas where there are no content below for the mix, only the layer of black color is used. You create transparency good, real luminance based on unmultiplying, that can be done with the Knoll Unmult plugin Red Giant Software (free) or the effect of changing the channel of the AE monitoring bey a color delete effect.

Mylenium

Omni 1020 120 pc: upgrade processor motherboard Sandy bridge

Can I use Intel Core i3-3220 (3rd generation) Ivy Bridge 3.3 GHz LGA 1155 55W Intel HD Graphics 2500 for my Omni 1020 120 pc aio pc?

Thank you for the information, @Nannigalaxy.

The information I needed was the (in) at the end of the model. Here are the processors that have been fully tested to work in your motherboard:

TDP: up to 65W
Socket type: LGA 1155
Motherboard supports the following processor upgrades:
Intel Pentium G4xx (Sandy Bridge) core
Dual-core Intel Pentium G5xx (Sandy Bridge)
Dual-core Intel Pentium G6xxT (Sandy Bridge)
Dual-core Intel Pentium G6xx (Sandy Bridge)
Dual-core Intel Pentium G8xx (Sandy Bridge)
Intel Core i3-2xxx/T (Sandy Bridge) Dual Core
Intel Core i3-2xxx (Sandy Bridge) Dual Core
Intel Core i5-2xxx (Sandy Bridge) Quad Core
Intel Core i7-2xxx (Sandy Bridge) Quad Core

These are processors that we know won't work correctly. If you use any processor not on the list, he has a good chance that it won't work.

Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

G6-1262sa Pavilion: Pavilion g6-1262sa CPU upgrade v2, Sandy Bridge = > Ivy Bridge?

Hi, thanks to the Pavilion g6-1262sa maintenance and manual cleaning and this great forum, I recently discovered that replace my i3-2330 m is possible with all sandy bridge i7 2620m processors.

These questions may sound silly, but I continued my research and I have more ideas to confront reality as a couple.

I realize that the compatibility is not only matter of editing the same socket, but also of the bios installed on certain motherboard, however:

1. do you think it would be possible to Exchange Sandy Bridge (2nd generation) i3 - 2330 m for some Ivy Bridge (3rd generation) i5-3210 m?

2 is the 32nm to 22nm manufacturing technology enough difference on its own (even if the rest of the architecture is the same) to prevent that to work?

3 is the bios from my card mother g6 identyfying somehow installed processor? (if this isn't on 'the list' it simply won't work? "or what technical compatibility issue?

According to some statements which I found it on some forums and sites (and a few facts documented free):

Socket: the two processors are compatible with BGA1023 decision-making. (at least that's what I found, if someone could confirm I would be grateful)

Difference of architecture: "The 3rd generation is called 'Ivy Bridge' and is essentially a copy of Sandy Bridge made on a smaller scale, or die." However, Intel also focused on beefing up of the onboard graphics in this generation. »

TDP: both are 35 W

Carrots: both are 2 physical (Virtual 4 - thanks to hyperthreading I guess?)

Energy consumption: "Ivy Bridge CPUS also use less energy", "Ivy Bridge consumes less energy; around 10w, I think. »

Temperature: i5-3210 m going 5 * C more - 2330 m - i3 shouldn't make much difference

Looking forward to some responses, RacA

It is not a technical incompatibility (socket) because as you probably know Ivy Bridge and Sandy Bridge are backward compatible on most motherboards desktop. However, HP has only implemented gen 2d, processor Intel Core compatibility of the HM65 Express chipset that you a. motherboards supporting 3rd gen processors use the HM77 chipset. There is no another motherboard that will fit in your frame.

Your analysis above, which was pretty good, left out the chipset, which you must always remember when assessing the possibilities of upgrade:

http://www.CPU-upgrade.com/MB-Intel_%28chipsets%29/HM65_Express.html

The HM65 supports a couple 3rd gen processors, but none of them are on the list of HP for your model. You can try one of those shown in the link I gave, but I think that there is a small chance that they will work.

If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

Fix for nasty bug of Sandy Bridge badly on USB devices

Anyone know if there is a fix yet, some USB devices fail intermittently on a new MB with Windows 7 64 - bit edition.

It is a quad core running the Sandy Bridge chipset, and vodafone dongles does work, even if they did on W7 64 bit on the former Council.

Fault too:-some external hard drives are not recognized on any port.

Your hard drives are connected via SATA?

There is a known issue with some Sandy Bridge chipsets, where ports SATA fail, don't know if it affects USB ports or not.

Intel issued a notice of recall for this with the affected chipsets - did you check the Intel website to see if you are one of those affected

Sandy Bridge chipset problem

New computers from Dell desktop XPS 8300 with processors Intel i7 2600 still have the 'Sandy Bridge chipset' fault on their motherboards 67-series? I read that Dell at first continued to build defective systems, while planning replace motherboards later for customers who have applied the patch. Is this still the case now?

Don't believe everything you hear / read:

en.Community.Dell.com/.../Intel-Chipset-issue.aspx

www.ZDNet.com/.../11220

They were 'fired' and is most sold once they have received the word of Intel on the issue. Once equipped with the chipset update, sales picked up. Motherboards have been replaced and returns available to those who bought before the problem came to light.

Yet another thread Sandy Bridge vs i7 - 9XX; 16GB vs 24 GB of memory?

Gentlemen.
Like many others, I read the hardware threads on an ongoing basis since getting CS5 about a year, including (I think) all items for damage. I feel that I have a basic understanding of the socket 1366 vs debate 1155/6. No need to re-hash things this time.
Yet, I think bad and others have made convincing for those who need the best, the X 58 with a big-time RAID configuration cannot be beat for the distribution of data and achieve the Holy Grail - balance. The worst the Z68 is derisory location of PCI-E lanes. I do not fully understand, but he can see that the many alleyways less, shared, is less than X 58. But don't the Z68 missing completely those of us who do not push the envelope? Who have a little more time waiting while the ' puter calculates?
I am on a budget and just want to spend my AMD Phenom II platform to an Intel platform. I mainly turn student videos of math which, by nature, must be no more than 5 minutes or more in length. My camera is a Canon T2i images so AVCHD. I took the advice of a member of the Board of Directors and will probably start shooting in VGA, questioning the sanity of shooting HD for clips that do not need to run mode full-screen. Overall, my requirements are on the low end (except for the codec. And I am ready to undertake NeoScene as a patch). I suspect that my needs are in line with many of those who can offer the student of CS5 version and find themselves in need of a new platform, but perhaps not ready for professionals.
Quick Sync appealed to me, that I need to transcode frequently for mobile devices. In addition, other teachers in the building along with camcorders JVC .mov, which means that they can not often change with their favorite software. I find myself any transcoding of our small team.
As I started to build something again over the summer, I'm trying to settle major issues in the face of those of us tax less end of the spectrum. I'll never get a RAID card, but have an arrangement of 5-disc basis, including a RAID on 2 discs 0 for a film. All I have to to is sorting out which platform is best for my needs of any
I'm just trying to move to Intel without breaking. But if another $ 250 for the X 58 will make a HUGE difference, so I would probably jump. Ventilation for a cheap (er) Intel platform:
CPU: i7 - 2500K. No Hyper-Threading but technology can overclock beyond more expensive i7-950. Only $30 cheaper than the i7-950. Spend $100 more for i7 - 2600K and get a higher Nehalem processor, but out behind on $$$.

Motherboards: Z68 starts about $130 for a decent spec'ed ASRock Z68 PRO3 to the ' egg. Fall another $20 for a combo with the CPU. Cripes, X 58 boards are expensive!
After the motherboard, i7 - 2500K and ASRock seek powerful good. $125 less than i7 - 950 and X 58 and who is with a X 58 cheaper Board. In addition, a four-stick kit memory 16GB is about $100 cheaper than 24 GB of G.Skill, rated either in ability Newegg brand. Economy of $225-ish. As long as my needs are satisfied, I'll save money and get a quick synchronization to start. At this point, I'm willing to bet that my short-clip needs will be met, in fact.
Thesis: Now, here can be the deciding factor - with the price of memory fall big-time, but within reasonable limits maximum memory on each platform. X 58 may take 24 GB, the senior Z68 to 16 GB. I remember Bill Gehrke saying that the first results of the suite of PPBM5 showed a difference in (rendering?) time with the jump to 24gigs. I think that the 16 GB looks like a lot of memory, which is. But dropping $100 for 24 concerts would be a game changer? I don't talk a 24 GB kits cheap with 9-9-9 times, not something jumped to hop to the top. (Requires X 58 memory super - duper or a motherboard $ 300 to run in fact 24 GB?)
X 58 may take 24 GB triple-channel memory would be the last word? For all of my tent to save $250 or more by going cheap (er) with i7 - 2500K SB, I'll miss on perhaps the most important? Most of the other programs in CS5 uses CUDA to accelerate - would be slightly less powerful i7-950 processor so supplemented by another 8GB (more than 50%!) of system memory that would apparently stealing other programs compared to SB?
If CS5 works just like a dog scalded on 24 GB, then I will suck and renounce Quick Sync and spend a little more money. I feel there is a difference of opinion if Sandy Bridge is a stronger for the edition CPU (even if there is no debate on X 58 vs Z68 for the processing of data). But it seems that there should be a clearer idea the benefits of 16 vs 24 GB of memory.
Everyone here would make a decision based on this last aspect?

Joel, the extra memory essentially has no effect on the scores of PPBM5 with the CS5 version. We do not yet have any information on the CS5.5. Look at the fourth note on PPBM5 it has been implemented with 14 GB on an X 58 Board. Ultra complex timeline manipulation and encoding may be a little different. I suspect this fall when the Sandy Bridge E CPU and motherboards are released that will start to see the memory strong 8 GB for these cards so that when this produces the current generation Sandy Bridge motherboards will be then be able to be upgraded to 32 GB as some motherboard manufacturers have promised.

Dynamic Cluster migration "Haswell" Intel and Intel 'Sandy Bridge' Cluster

Similar Questions

Maybe you are looking for